HARVIA SASS016 Installation guide

Installation instructions

1

Y05-1173

HARVIA BLOCK- manual

EN

Installation instructions

2

Y05-1173

Necessary tools and symbols

BLOCK BENCH MODELS

EXTEND

BOX

AIR

Installation instructions

3

Y05-1173

VONTENT:

BENCH HEIGHTS 4

INSTALLATION OF BENCH FRAMES 4

INSTALLTION OF LOWER BENCH 5

SUPPORTING OF BENCHES 7

BENCH SKIRTS 8

BENCH DECKS 8

BACK RESTS 9

FOOTREST 10

STOOLS 11

CORNER BENCHES 11

BENCH FRAMES 12

SUPPORTIVE LEGS 13

LOWER BENCHES 13

BENCH SKIRTS 14

BENCH DECKS 14

BACK RESTS 15

FOOTREST 16

ROUNDING OF BENCH 17

ROUNDING OF BENCH SKIRT 18

ROUNDING OF BACK REST 19

DECORATIVE BENCH END 20

ARM REST 21

LED-LIGHTS 22

Installation instructions

4

Y05-1173

BENCH HEIGHTS

Check bench heights from offer. Measure and mark level of upper bench frames. Notice, that bench frame is

28mm below bench deck top! Install upper benches onto frames behind wall panels.

INSTALLATION OF BENCH FRAMES

Measure the distance between bench frames and side walls. Fill up the gap with plywood pieces (4mm / 6mm).

Screw bench frame onto frames behind panels.

Zn 6*120mm

Installation instructions

5

Y05-1173

Install upper bench frame also from side. Remember to use plywood pieces in the middle!

INSTALLATION OF LOWER BWNCH

Measure and mark place of the lower bench. Check right position from the offer or in the picture below, which is

showing the right position of lower bench relating upper bench.

Zn 6*120mm

Installation instructions

6

Y05-1173

NOTICE! In AIR-model lower bench starts from the back wall.

EXTEND

BOX

AIR

Depth position of lower bench

must be measured from upper

bench!

Zn 6*120mm

Installation instructions

7

Y05-1173

SUPPPORTING A BENCH

IF width of lower bench is over 1600mm, bench support is needed.

IF width of bench < 1800, install supportive leg for lower bench as in picture ABOVE.

IF width of lower bench > 1800, install supportive leg for BOTH of benches as in picture BELOW.

BLOCK AIR ->

IF width of lower bench is over 1800mm, bench support is needed.

Install supportive leg from behind of bench frame.

5*100mm

5*80mm

X*XXmm

BOX

EXTEND

5*80mm

EXTEND

4,5*50mm

Installation instructions

8

Y05-1173

BENCH SKIRTS

Install bench skirts behind front board of upper bench frame.

BENCH DECKS

EXTEND

4,5*45mm

EXTEND

BOX

Installation instructions

9

Y05-1173

BENCH DECKS (AIR)

suos

BACK RESTS

Big bench decks are made of several pieces to ease

installation and cleaning.

Picture indicates recommended

height of back rest according to upper

bench. Measure, predrill and install.

Wires of LED-lights are recommended

to be installed behind wall boards.

4,5*45mm

TIP! You can choose height of back rests also

according to user.

Installation instructions

10

Y05-1173

FOOTREST

Place footrest on place and mark with pen. Mark places of screws with rubber washers and drill screw holes

through deck boards. Place footrest onto rubber washers (2 layers) and screw underneath deck.

4,5*45mm

Installation instructions

11

Y05-1173

STOOLS

Stools are preassembled.

CORNER BENCHES

Installation instructions

12

Y05-1173

BENCH FRAMES

Install upper benches onto frames behind panels.

Mount benches together from two directions!

5*80mm

Zn 6*120mm

Installation instructions

13

Y05-1173

SUPPORTIVE LEG

Install supportive leg into joint of benches. Lower bench will also be supported with supportive leg.

LOWER BENCHES

Install first bench onto wall and onto supportive leg. Mount benches together from two directions!

4,5*45mm

5*80mm

Installation instructions

14

Y05-1173

BENCH SKIRTS

Install bench skirts behind front board of upper bench frame.

BENCH DECKS

4,5*45mm

Lift and turn decks carefully

on places. Right position is

marked in every deck.

Installation instructions

15

Y05-1173

BACK RESTS

TIP! You can choose height of back rests also according to user.

Picture indicates recommended height of

back rest according to upper bench.

Measure, predrill and install.

Wires of LED-lights are

recommended to be

installed behind wall boards.

4,5*45mm

Installation instructions

16

Y05-1173

FOOT REST

4,5*45mm

Place footrest on place and

mark with pen. Mark places of

screws with rubber washers

and drill screw holes through

deck boards. Place footrest

onto rubber washers (2 layers)

and screw underneath deck.

Installation instructions

17

Y05-1173

ROUNDING OF BENCH

4,5*60mm

Installation instructions

18

Y05-1173

ROUNDING OF BENCH SKIRT

4,5*45mm

Installation as bench skirst.

Look page 13.

Installation instructions

19

Y05-1173

ROUNDING OF BACK REST

4,5*45mm

Installation as back rest. Look page 14.

Installation instructions

20

Y05-1173

DECORATIVE BENCH END

4,5*45mm

Page is loading ...

HARVIA SASS016 Installation guide

This manual is also suitable for

HARVIA SASS016 Installation guide

Related papers

Other documents