Corona Low End Bed - 4ft6
Assembly Instructions
www.happybeds.co.uk
Important before assembly: .
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
Assemble the product as close to its intended final location/room as possible.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Further instructions are on the following pages.
Please keep these instructions for future reference.
@
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause damage to the
joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please contact our
customer services (details at the back of these instructions)
(Not metal)
These tools are not
necessary, but may help
to assemble the product.
Do NOT use any power
tools as this may
damage the frame.
Part Item Qty
30mm dowel
16mm Screw
30mm Screw
Nut
50mm Bolt
120mm Bolt
Half moon nut
A
D
G
L
B
E
J
M
C
F
K
8
4
52
8
2
2
10
8
8
40mm dowel 130mm Bolt
Recycle
2m
01 2 345 6 789 1 0
mm 1 1 1 2 1 3 1 4 1 5 1 6
Part Item Qty
32mm Bolt 2
H
N
Metal bracket
O
2
You will need a screwdriver, small mallet
and M11 spanner (not provided).
2
Spacer
1
Allen key
4
Round metal stud
1Headboard panel (132 x 49cm) - Box 1
2Headboard rail (132 x 9.2cm) - Box 1
3Footboard panel (132 x 17.3cm) - Box 1
Left headboard post (110 x 8.2cm) - Box 2
4
Right headboard post (110 x 8.2cm) - Box 2
5
Left footboard post (56 x 8.2cm) - Box 2
6
Right footboard post (56 x 8.2cm) - Box 2
7
Side rail x 2 (190 x 11.2cm) - Box 2
8
Centre rail (195.5 x 6.5cm) - Box 2
9
10 Slat x 26 (68.2 x 6.5cm) - Box 1 11 Support leg x 2 (28.3 x 6.5cm) - Box 1
HARDWARE LIST - Box 2
12 Hardware Kit x 1 - Box 2
2x
G
B
B
A
A
A
A
A
A
11
11
9
8
N
1
2
3
Step 2: Insert hardware part A to the headend panel (1), footboard panel (3) and Headboard rail (2) using a small mallet
(not provided).
Step 1: Join the support legs (11) to the centre rail (9) using hardware N and G.
Insert hardware part B to the side rails (8) using a small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
H
H
H
H
H
H
H
H
H
H
N
1
4
5
5
4
2
N
67
3
6
7
Step 4: Attach the left footend post (6) and right footend post (7) to the footend panel (3) using hardware
parts N and H.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 3: Attach the left headboard post (4) and right headboard post (5) to the headend panel (1)
and headend rail (2) using hardware parts N and H.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
1
C
J
E
F
K
3
L
L
L
1
8
89
N
8
9
Step 5: Fix hardware parts L to the headboard rail (2) and footboard panel (3) using hardware part C
and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 6: Attach the side rails (8) to the headboard posts using hardware parts N, J and K. Fix the centre rail (9)
using hardware parts E and F with an M11 spanner (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
1
b:
a:
J
K
E
F
D
D
3
N
8
9
3
10
10
10
10
10
10
O
O
10
10
Step 8: Fix slats (10) to the side rails (8) and centre rail (9) using hardware parts O and D with a screwdriver (not provided).
Make sure to start from the ends and work towards the middle.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 7: Attach the footend using hardware parts N, J and K and fix the centre rail (9) in place using
hardware parts E and F with an M11 spanner (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
9
8
8
160mm
50mm
Step 9: Insert hardware part M using a small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
M
M
MM40mm
40mm
www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the product across the floor as
this will cause damage to the joints. If the product is used on hard flooring, such as wood or laminated
floor, you must place some protection under the legs to stop the product from moving. If this is not
adhered to, it could result in failure to the product that will invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
In the unlikely event that you have problems putting this product together or have damaged or
missing parts, please contact us by visiting:
https://www.happybeds.co.uk/customer-service
Notes
/