SKODA RNS 310 Skoda Amundsen Owner's manual

Brand: SKODA

Model: RNS 310 Skoda Amundsen

Category: Car video systems

Type: Owner's manual

This manual is also suitable for

SIMPLY CLEVER

www.skoda-auto.com

Navigace Amundsen

Octavia, Superb, Yeti anglicky 05.09

S00.5610.66.20

3T0 012 149 AR

ŠkodaAuto

RADIO NAVIGATION SYSTEM AMUNDSEN

Amundsen.indd 1Amundsen.indd 1 26.3.2009 12:44:1326.3.2009 12:44:13

Škoda Auto pursues a policy of constant product and model development. We trust

that you will understand that changes to models in terms of shape, equipment and

engineering, may be introduced at any time. The information about scope of

delivery, appearance, performances, dimensions, weight, fuel consumption,

standards and functions of the vehicle is only correct at the time of publication.

Certain items of equipment might only be installed later on (information given by

the local authorised Škoda Service Partner) and only envisaged for particular

markets. It is therefore not possible for legal claims to be made based on the data,

illustrations and descriptions contained in this Owner's Manual.

Reprinting, reproduction or translation, either in whole or in part, is not permitted

without the written consent of Škoda Auto.

Škoda Auto expressly reserves all rights relating to copyright laws.

We reserve the right to make changes to this document.

Issued by: ŠKODA AUTO a.s.

Amundsen.indd 2Amundsen.indd 2 26.3.2009 12:44:1726.3.2009 12:44:17

Introduction

You have chosen a Škoda vehicle, which is fitted with an Amundsen radio navigation system (hereafter

called the navigation system) - we thank you for your confidence in us.

We recommend that you read these operating instructions carefully so that you can quickly become familiar with

your navigation system.

Should you have any questions or problems with your navigation system, please do not hesitate to contact your

authorised Škoda Service Partner or importer.

National legal provisions, which deviate from the information contained in these operating instructions, take prec-

edence over the information contained in the operating instructions.

We hope you enjoy using your navigation system and wish you pleasant motoring.

Your Škoda Auto

s36c.b.book Page 1 Thursday, April 9, 2009 2:50 PM

Contents2

Contents

General information . . . . . . . . . . . . . . . . .

Equipment overview . . . . . . . . . . . . . . . . . . . . . . . . . .

Important information . . . . . . . . . . . . . . . . . . . . . . . .

Range selector key SETUP . . . . . . . . .

Tone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Radio set-ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Traffic station set-ups . . . . . . . . . . . . . . . . . . . . . . . . .

Screen set-ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Media set-ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Navigation settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Range selector key RADIO . . . . . . . .

Radio mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Traffic information function TP . . . . . . . . . . . . . . .

Range selector key TRAFFIC . . . . . .

Displaying TMC traffic reports . . . . . . . . . . . . . . . .

Range selector key MEDIA . . . . . . . .

General information for CD operation . . . . . . .

Main menu MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Audio menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MP3 and WMA data . . . . . . . . . . . . . . . . . . . . . . . . . .

External sources* . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Range selector key NAV

(Navigation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Destination entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Destination memory . . . . . . . . . . . . . . . . . . . . . . . . . .

Route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

s36c.b.book Page 2 Thursday, April 9, 2009 2:50 PM

General information 3

General information

Equipment overview

Control button for switching the unit on/off (press) and for

setting the volume (turn) of the currently replayed audio source

Range selector key for selecting the corresponding menu:

− - changes over into the radio mode and changes the

frequency range when in the radio mode

− - changes over to the last played media source or selects

a new media source

− - Mute

− - switches on the navigation

Fig. 1 Radio - Overview

RADIO

MEDIA

PHONE

NAV

s36c.b.book Page 3 Thursday, April 9, 2009 2:50 PM

General information4

− – switches on the stored TMC traffic reports display

(Traffic-Message-Channels) = Traffic Message Channel

− - enables setting-up the individually selected field

°and° : the backwards/forwards keys operate the “active” audio

source

−RADIO mode - for the selection of the station from the station or

memory list

−MEDIA mode - for the selection of the previous or following track

(briefly press), fast forward/reverse (press for a long period of

time)

CD case

Touch screen (Touch-screen): fields circled in colour on the screen

are presently “active” and are operated by touching the screen

Eject key - press briefly to move an inserted CD, ready for

removal, into the initial position

- displays additional information depending on the current oper-

ating mode

−RADIO mode - switches the radio text display on/off

−MEDIA mode - changes between the display of the time and the

name of the title during the MP3/WMA play function

−NAV mode - displays the information regarding the vehicle posi-

tion and enables additional functions (flag dtns., routenlist,

exclude a stretch)

−TRAFFIC mode - displays the currently received TMC station

Button to return from a menu to the previously selected menu

AUX socket to connect an external audio source

Menu control button

−Mark a function or a sub-menu, set a value (turn)

−Select a function or a sub-menu, confirm a value (press)

Function buttons - the function of the respective button is displayed

on the screen

Memory card case: The SD cards (Secure Digital) and the MMC cards

(Multimedia Cards) have a memory capacity of 4°GB and the SDHC

cards (Secure Digital High Capacity) have a memory capacity of

32°GB and a dimension of 32 mm x 24 mm x 2.1 mm. The case for

the memory card is located next to the screen.

Explanation of symbols

* items of equipment which are marked in such a way are only installed as standard

on certain models or are supplied as special equipment.

 End of a section.

b The section is continued on the next page.

Important information

Warranty

The equipment warranty terms and conditions also apply for new vehicles.

After the expiration of the warranty, a piece of equipment in need of repair will be

replaced with a reconditioned, original item with spare part warranty. It is, however,

a precondition that the housing has not been damaged and no unauthorised

attempts have been made to carry out repairs.

Note

Damage within the meaning of the warranty must not be the result of improper

handling of the system or from unprofessional repair attempts. It is also essential

that there is no external damage.

Information on how to operate the navigation system

The requirements of today's road traffic demand the driver’s full concentration at all

times.

Apart from the availability entertainment, the extensive and demanding equipment

details of this system also offer a wide range of information, which will help you to

reach your destination quickly and safely.

TRAFFIC

SETUP

3 

6

7º

s36c.b.book Page 4 Thursday, April 9, 2009 2:50 PM

General information 5

But you should only operate the navigation system with its wide range of

possibilities when the traffic situation allows.

The volume settings must be selected in such a way that audible signals from the

outside, e.g. a Martins horn from utility vehicles (police cars, ambulances and fire

brigade), can be heard at all times.

WARNING

Please concentrate fully at all times on your driving! As the driver you are

fully responsible for road safety. Only use the functions in such a way that

you are always in full control of your vehicle in all traffic situations!

Before using the navigation system

•Please observe the respective traffic regulations when driving.

•Street and location names can be changed. It is therefore possible that the

names stored on the CD might not correspond to the changed names.

•The route calculated by the navigation system is a recommendation for

reaching the intended destination. While driving please pay attention to stopping

restrictions, traffic lights, one-way streets, lane change restrictions, canals and

ferries.

WARNING

Road traffic legislation (StVO) applies at all times, even if a driving recom-

mendation contradicts the StVO.

Caution

•Inserting a second CD while a CD is being ejected can destroy the CD drive in

the unit. Please note that the CD ejection lasts a few seconds after pressing the

Eject button . During this time the lock in front of the CD case is open. It is

essential that you wait until the CD has been fully ejected before you try to insert a

new CD.

•Press the buttons and the keys of the unit gently in order to avoid damaging

them. Gentle pressure on the appropriate key is sufficient to operate the unit.

Please note that the control buttons have predetermined breaking points, in order

to reduce the risk of injury.

•Do not use any pointed or sharp-edged objects to operate the touch-screen.

Slight finger pressure sufficient to operate the equipment. A display on the screen,

which cannot be called up by pressing the button, is therefore not available at that

time.

•Please note that a dirty or scratched navigation CD can considerably impair the

speed and the functions of the navigation system.

Screen care

Treat the screen with great care, because dents and scratches can occur through

finger pressure or contact with sharp objects.

The screen can be cleaned with a soft cloth and finger marks can be wiped away

with pure alcohol.

Note

Do not use solvent such as turpentine or petrol as they will attack the screen

surface.

Anti-theft protection

The anti-theft coding of your navigation system prevents an operation of

the system after a voltage interruption, e.g. during a vehicle repair or after

theft. After disconnecting the battery, disconnecting the navigation

system from the on-board voltage of the vehicle and after a fuse failure,

the code must be entered before the vehicle can be used again.



s36c.b.book Page 5 Thursday, April 9, 2009 2:50 PM

General information6

Enter code

– If a keypad appears after switching on with the command to enter the

code, the unit can be unlocked by entering the correct four-digit code

number. The number of the possible attempts is shown in the bottom

screen line.

– Press a digit from to on the digit block displayed on the screen.

The digit is accepted in the entry line.

– After a four-digit order has been entered, the group of digits will turn

grey (inactive) and no further digits can be accepted in the entry line.

– Press on the screen in order to delete the digits in the entry line

from right to left and thereby correct your input, if necessary.

– If the correct code number is displayed in the entry line, press .

Code number

The code number can only be called up “online” via the Škoda system, as this guar-

antees even more effective anti-theft protection. Please contact your authorized

Škoda Service Partner, if necessary.

Incorrect code number

If an incorrect code is confirmed after entry of the code, the procedure can be

repeated twice. The number of possible attempts is shown in the bottom screen

line.

If the code number is entered incorrectly for the third time, the unit will be blocked

for approx. one hour. It is possible to enter again the safety code after one hour has

expired, when the unit and the ignition have been switched on.

If three invalid attempts are then made again, the navigation system will be blocked

again for an hour.

The cycle - three attempts, blocked for an hour - will continue to apply.

Note

The code is normally stored in the instrument cluster. This ensures that it is auto-

matically decoded (convenience coding). Manual input of the code is normally not

necessary.

0 9

Delete

s36c.b.book Page 6 Thursday, April 9, 2009 2:50 PM

General information 7

Operation when driving

The demands of today's road traffic require full concentration from all road users at

all times.

WARNING

•Always concentrate fully on your driving. Inattention by the driver can

lead to accidents and injuries.

•Do not allow yourself to be distracted by trying to use the unit, concen-

trate instead on the traffic situation.

•Use the unit only if road, weather and traffic conditions permit and you

will not be distracted.

•The various volume settings must be selected in such a way that audible

signals from the outside, such as e.g. a Martins horn from police cars and fire

brigade, can be heard at all times.

Note

Depending on the country, some functions of the radio navigation system can no

longer be selected on the screen at certain speeds. This is not a malfunction, but

corresponds to the legal requirements of this particular country.

Special functions

Parking aid*

If your vehicle is equipped with “parking aid” and after it is activated, the distance

to the obstacle is shown on the screen.

Climatronic*

If your vehicle is equipped with climatronic, a feedback is received on the screen

when changing the settings.

Personalisation

Your vehicle can be equipped with up to four keys. Individual settings of the unit are

always assigned to the key, which is currently inserted in the ignition lock. In prac-

tice, this means that each time you use another vehicle key, the setting of the unit

which is assigned to the key is carried out.

Switching the system on and off

– The system is switched on or off by pressing the control button .

The last active audio source before switching off is repeated.

If the key is pulled out of the ignition lock while the unit is switched on, the unit will

switch off automatically. You can then switch the unit on again. If the ignition is

switched off, the system switches off automatically after approx. half an hour

(vehicle battery protection against discharging). This process can be repeated as

often as necessary.

General - operation

The screen of the unit is a so-called touch screen (touch-screen). Fields

circled in colour on the touch-screen are presently “active” and are oper-

BAT-20H1069 Fig. 2 Menu radio

s36c.b.book Page 7 Thursday, April 9, 2009 2:50 PM

General information8

ated by touching the screen. Active fields, which call up a function or a

menu, are called “function buttons” / .

The following information is displayed in the main menu:

the selected radio station (its frequency or designation);

selected waveband;

activation for the reception of traffic reports;

current menu.

“Pop-up window”

If you press the function key on the screen, a so-called “pop-up window” will

open where all possible set-up options are displayed.

Briefly press the desired set-up option. The pop-up window will disappear and the

newly selected set-up option is displayed in the function key.

“Check box”

Some functions can only be switched on or off.

There is a so-called “check box” in front of a function which can only be switched

on or off. A tick in the check box 7 indicates that the function is switched on, an

empty check box 8, indicates that it is switched off.

Briefly press the corresponding function key for switching on or off.

Input mask for free text input

In some of the menus you can enter a free text, for example, when

entering a new destination or while searching for the name of a point of

interest.

– Press to accept a character sequence offered by the system or

press in order to delete the characters in the entry line.

– When in the entry window, press on a character shown on the keypad

block to accept it into the entry line.

– You can also delete or change the character sequence in the entry line

as well as insert additional characters.

Further input possibilities:

- changes from upper case to lower case and vice versa.

- opens the input mask for digits and special characters. The function key

changes to . Press , to change again to the letter input mask.

 - space key for entering spaces.

or - moves the character entry cursor (the cursor) in the entry line to the left

or right.

- opens a pop-up window with special characters.

FBAT-20H1085

Fig. 3 Input mask for free

text input

Delete

A-Z A-Z

 b

ÄÜ

s36c.b.book Page 8 Thursday, April 9, 2009 2:50 PM

General information 9

- deletes characters in the entry line starting from the position of the char-

acter entry cursor from right to left.

Selecting letters based on specific characters

Some letters in the input masks are also marked with a small triangle “a”. This indi-

cates that specific characters based on this letter can be selected.

Continue to press down on the corresponding function key with your finger until a

pop-up window with these specific characters can be displayed. Press to accept the

desired character into the entry line - the pop-up window will close. If no entries are

entered, the pop-up window will close automatically after a few seconds.

Input mask for selecting the destination address

When entering the destination address, it is only possible to enter the

characters in the sequence which corresponds to the destinations stored

in the navigation system.

Limiting the destination and selecting from the list

– You can open a list of the selectable destinations any time by pressing

the function key while making entries in the entry line. Only

destinations selectable from the navigation memory which corre-

spond to the requirements and the character sequence in the entry

line will be displayed.

– The number of selectable destinations will be displayed in the entry

line if fewer than 99 destinations can be selected.

–If fewer than six destinations are selectable, the entry window will

close automatically and a list of possible destinations will be

displayed.

Delete

BAT-20H1086

Fig. 4 Input mask for

selecting the destination

address

List/OK

s36c.b.book Page 9 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP10

Range selector key SETUP

Tone settings

By pressing the button and pressing on the function key in the RADIO

mode, you can select the following parameters using the menu control button :

• - , ,

and - Volume when switching

on, volume of incoming traffic announcements, volume of navigation announce-

ments and speed dependent volume adjustment;

• - Treble setting;

• - Midtone setting;

• - Bass setting;

• - Setting of the volume ratio between the left and right side;

• - Setting of the volume ratio between the front and the rear;

•* - Setting the equalizer (linear, language, rock, classical, dance);

•* - setting of the surround tone.

GALA function

Your radio increases automatically its volume with the increasing vehicle speed. A

higher setting value results in a stronger volume increase.

Note

You can set the tone parameters using the menu control button or the function

keys or .

System settings

Press the button and select the function key .

You can select between the following parameters:

• - Menu language for the displays and the language messages;

• - Keypad display for text entry;

•* - if your vehicle is equipped with climatronic, the setting

change is displayed when it is activated;

• - Setting the brightness of the screen;

• - Factory settings;

• - the information regarding the complete memory capacity of

the SD card and the size of the memory assigned to the navigation data is displayed

on the screen;

• - Removing the SD card.

Radio set-ups

Press the button in the RADIO mode.

Switching the traffic announcements on or off

– If you wish to switch the reception of traffic reports on or off, press the

function key .

Determining the station selection via the

– By pressing on or , you can select the source

from which the stations are to be selected while in the RADIO mode

using the arrow keys. If the is selected, only stored

stations from the memory list are called up. The symbol “ @ ” is

displayed on the screen.

Switching the RDS function on or off (RDS regional)

– Press on the function key (regional station) and select a

set-up in the opening pop-up window.

SETUP Tone

Volume Maximum switch on volume Traffic announcements (TP)

Navigation volume Speed dependent vol Adjustment

Treble

Midtone

Bass

Balance

Fader

EQ Settings

Surround

+ -

SETUP System

Language

Keypad display

A/C display time

Screen

Factory settings

SD card status

Remove SD card

SETUP

Traffic information (TP)

Arrow keys

Station list Memory list

Memory list

RDS regional

s36c.b.book Page 10 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP 11

– Press on the button , doing so always chooses the

frequency for the heard radio station which offers the best reception

at the present time.

– When pressing on the button , the unit attempts to hold a radio

station emitting regionally long enough until the reception quality is

so bad, that there is a risk of a program loss.

Delete stored stations

– Press the function key and confirm the following safety interroga-

tion in order to delete all radio stations stored in the memory list.

Traffic station set-ups

Press the range selector key and then the range selector key

Switching the traffic announcements on or off

A tick in the check box 7 indicates that the traffic radio function is already switched

on.

Dynamic route

Opens a pop-up window where it is considered if the TMC traffic reports, received

during the route calculation, are to be entered.

Screen set-ups

Press the button in the RADIO mode and then the function keys

and .

Brightness

– Press the function key and select the desired setting for

brightness (5°stages) in a pop-up window.

– A light sensor, which is located in the top right corner of the front

panel, is used for the automatic correction of the brightness

depending on the light conditions in the vehicle.

Day/Night

– Press on the function key and select a setting in the pop-up

window.

– Press the function key if switching the headlights on and off

should also change the map display from night to day design.

– Press on the function key or to manually determine the

night and day design of the map display.

Confirmation tone

– Press on the function key and select a setting in the

pop-up window.

– Press or to switch the tone for confirmation of a function key

operation on the screen on or off.

Media set-ups

Press the button in the MEDIA mode.

Function keys in the menu°-°Media

• - a tick in the check box 7 means that the function of the

traffic information is switched on.

• - Check box for setting the play function mode Scan,

Mix and Repeat incl. sub-folder (“switched on”) or without sub-folder (“switched

off”).

• - Setting the volume of the external audio source (audio source

AUX is located on the unit).

Automatic

Fix

Delete memory

All

TRAFFIC

SETUP

Traffic information (TP)

Dynamic route

SETUP

System Screen

Brightness

Day/Night

Automatic

Day Night

Confirmation tone

On Off

SETUP

Traffic information (TP)

Scan/Mix/Repeat incl. 

AUX Volume

s36c.b.book Page 11 Thursday, April 9, 2009 2:50 PM

Range selector key SETUP12

•* - Setting the volume of the external audio source (the audio

source MDI is located under the armrest of the front seats or in a storage compart-

ment on the front passenger side).

•* - enables a wireless transfer of MP3 data to the tele-

phone preinstallation. Only operates in combination with the telephone preinstal-

lation GSM°l - enables the audio play function by means of Bluetooth interface of

portable units (mobile phones) which support the protocol A2DP.

Navigation settings

Press the button in the Navigation mode.

Function keys in the menu°-°Navigation

• - route options are determined according to the route being

calculated and along which roads the route should lead ,

, and - Route criteria, dynamic

route guidance, route without motorways and route without toll roads/ferries.

• - Setting the volume of the navigation announcements.

• - changes between day and night display, as well as automatic, if the

map display changes automatically according to the setting of the light switch.

• - displays a point of interest on the map.

• - changes the map scale automatically depending on the speed and

the driven route (Motorway trip: small map scale - City center: large map scale).

• - during a route guidance, either the arrival or the driving time is

shown in the map display.

• - Enter home address.

• - you can start a virtual (apparent) route guidance in the demo

mode. Virtual route guidance will be repeated when reaching the fictive travel

destination. Stop virtual route guidance normally and deactivate the demo mode

to restart “real” route guidance. As in this case the unit must first reorient itself it can

take some time, depending on the number of the currently receiving satellites, until

the unit has again found the real location. Drive a short distance.

• - Entering a fictive (invented) starting point in the

demo mode.

• - Deleting the destination memory or the list of the

last destinations.

• - Display of information via the data base on CD or SD

card, delete the data base of the SD card or copy the data.

Route criteria

Fast: It calculates the fastest route to your destination, even if a detour is necessary.

Short: Longer driving time in favour of a shorter route is acceptable. Please note

that the setting “Short route” during route guidance can sometimes lead to unex-

pected results.

Economical: The aim of the calculation is a balance between minimal driving time

and driving distance.

Dynamic route guidance with TMC use

If the dynamic navigation is switched off, traffic reports are nevertheless received in

the background and updated. The navigation displays traffic problems on the map

and draws attention to them verbally, however does not consider them for calcu-

lating the route (the route can lead through the traffic problems).

MDI Volume

Activate Bluetooth audio

SETUP

Route options

Route criteria

Dynamic route Avoid motorways Toll road/avoid

Announcement volume

Day/Night

POIs on map

Autozoom

Time display

Enter home address

Demo mode

Demo mode starting point

Delete destinations memory

Data base navigation

Route criteria

Dynamic route

s36c.b.book Page 12 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO 13

Range selector key RADIO

Radio mode

Retrieve radio station

Call up main menu RADIO and choose frequency range

– Press the range selector key . The currently heard radio station

is displayed in the middle of the screen ⇒page 7, fig. 2 .

– Press the range selector key to change the frequency range.

Alternatively, press on the function key in the main menu

RADIO and select or in the pop-up window.

Changing radio station

– By briefly pressing the function keys or , you can change to the

previous or following radio station of the selected frequency band.

– If the symbol “TP” is displayed on the screen, you can only change

over to the radio stations with traffic announcements.

– If the symbol “ @ ” is displayed on the screen, you can only

change over to the stored radio stations.

Selecting a radio station from the station list

– If you wish that all the presently receivable radio stations are

displayed, press on the function key and then on the func-

tion key . The list “skips” directly to the display of the currently

heard radio station.

– Select the desired radio station using the menu control button .

Change radio station in the memory list

– Press the function key and then the function key and

select the desired radio station using the function keys - .

Manual station finding

– If you wish to set the radio station manually using its frequency, press

the function key and then the function key .

– Set the radio station using the menu control button or using the

arrows and on the unit.

BAT-20H1064

Fig. 5 Menu radio: Function

key band

BAT-20H1064 Fig. 6 FM station list

RADIO

Band

FM AM

 

Freq. Band

FM/List

Extras Memory

124

Extras Manual

 

s36c.b.book Page 13 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO14

– Briefly press the set button to terminate the manual frequency selec-

tion and to display once again the function keys.

Scan function

– In order to start the automatic play in the current frequency range,

press the function key and then the function key . All radio

stations with strong reception are automatically played for approxi-

mately five seconds according to the sequence in the station list.

– Press on the function key to end the automatic play of the

currently heard radio station.

Storing a radio station

– Press the function key and then the function key in

order to open the memory list.

– If you wish to store the displayed radio station in a memory space,

press one of the displayed station keys to and hold it

pressed for so long until a signal sounds. The currently heard radio

station is then stored on this station key.

Deleting a radio station from the memory list

– Press the button in the RADIO mode and then the function key

– Select the radio station you wish to delete and confirm by pressing the

menu control button .

– If you wish to delete all the stored radio stations, press on the function

key .

Note

It is alternatively possible to store radio stations by pressing the menu control

button .

Calling up a radio station

Calling up a station via the station keys

– Press the button and then the button and the function

key .

Extras Scan

Scan

Extras Memory

1 ... 24 ...

SETUP

Delete memory

All

BAT-20H1063 Fig. 7 Memory list

BAT-20H1075

Fig. 8 Setting the source for

selecting the station

RADIO Extras

Memory

s36c.b.book Page 14 Thursday, April 9, 2009 2:50 PM

Range selector key RADIO 15

– You can select the station stored on one of the station keys to

in the main menu RADIO by briefly pressing the desired station key.

Calling up available stations from the memory list

– Press the button and then the button and the func-

tion key .

– Select the desired radio station using the menu control button .

RDS function

– If you wish to switch the display of additional information to a radio

station on or off, press the button , the function is displayed in the

top right corner of the screen by the letter “i”.

RDS (“Radio Data System”) serves to transmit program identification and additional

services therefore also enabling automatic tracking of stations.

In the event of sufficiently satisfactory reception, the suitable RDS radio stations will

display the station name instead of the station frequency.

If a radio station sends additional information via the RDS function while a station

is being stored, it can occur that the name of the radio station is later displayed

incorrectly in the memory list. In this case, the stored station name can be restored

by selecting the desired radio station, wait until the correct station name is

displayed as radio text then press the menu control button and a pop-up

window is displayed on the screen.

Traffic information function TP

Switching traffic information TP (Traffic Program) on or off

– Press the function key in the RADIO mode.

– Briefly press on in the opening pop-up window to switch the

traffic information on or off.

The display “TP” in combination with a station name (e. g. in the station or memory

list), indicates a traffic information station.

Irrespective of which radio station is heard, an additional receiver part in the unit

ensures that a traffic information station can always be received as long as the traffic

information function is switched on.

The functionality of the function for the traffic information “TP” is displayed at the

top right in the screen.

If no traffic information station can be received because, for example, radio recep-

tion is interrupted in general, “No TP” will be displayed instead of “TP”. Remember

that car parks, tunnels, high buildings or mountains can interrupt the radio signal

up to the total loss of reception.

Incoming traffic announcement

If you wish to interrupt the transmission of the traffic announcement, press on the

function key in the pop-up window Traffic announcement. The traffic infor-

mation function remains available and a following traffic announcement is

replayed if a random source is switched on. Pressing the function key will

switch off the traffic information function permanently.

124

RADIO Freq. Band

FM/List

Station name stored

Extras

Cancel

TP off

s36c.b.book Page 15 Thursday, April 9, 2009 2:50 PM

Range selector key TRAFFIC16

Range selector key TRAFFIC

Displaying TMC traffic reports

TMC traffic reports are used during route guidance, depending on the

set-up for the automatic optimization of the route, to report possible

traffic problems.

– Press the range selector key to display the current traffic

reports in a list.

– Press on the display of a traffic report to show it in a detailed display.

– You can browse through all the traffic information received in the

detailed display, in sequence by using the function keys.

Traffic problems are illustrated in the detailed display and in the map by a corre-

sponding symbol. The direction, in which the traffic problem is found in the map, is

displayed in colour. A traffic problem which is located on the route (in direction of

travel) is marked in red, a traffic problem in the opposite direction is marked in grey.

Note

•The unit has a continuous background of TMC traffic reports providing a TMC

station at the current location can be received. The station you are listening to does

not have to be a TMC station.

•TMC traffic reports can only be evaluated and stored by the unit if the nagi-

vation data (SD card or CD) is available for the driven area.

•The quality of the dynamic route guidance depends on the transmitted traffic

announcements. The radio stations broadcasting this information are responsible

for the content.

•TMC traffic reports are necessary for the dynamic navigation.

•There may not be any advantage in avoiding the traffic jam if, as a result of the

TMC traffic reports, the diversion is also heavily congested.

TRAFFIC

s36c.b.book Page 16 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA 17

Range selector key MEDIA

General information for CD operation

Audio-CDs (CD-A) and MP3-CDs can be played in the internal drive.

CD not legible

If you insert a CD which cannot be read by the unit, a pop-up window is displayed

with a note. Press on the function key , the CD is driven to the initial position.

If the CD is not taken out within 10 seconds, it is drawn in again for safety reasons.

WARNING

•The CD player is a 1st class laser product. There is a definite risk of injury

from invisible laser beams if it is opened.

•The CD player contains no parts that have to be serviced or repaired.

Please contact your specialist garage if a mechanical defect occurs or the CD

player has to be repaired.

Caution

•Inserting a second CD while a CD is being ejected can destroy the CD drive in

the unit. Please note that the CD ejection lasts a few seconds after pressing the

Eject button . During this time the lock in front of the CD case is open. It is

essential that you wait until the CD has been fully ejected before you try to insert a

new CD.

•If the CD drive becomes mechanically defective or a CD has been inserted

incorrectly or not fully, “Fault:°CD” will be displayed on the screen. Please check the

CD and place it again correctly and fully into the drive. If “Fault:°CD” is indicated

again, please contact your Škoda Service Partner.

•If the inside temperature of the unit is too high, no CDs will be accepted. The

unit switches into the last active operating mode.

Note

•If the function key is inactive, no new Audio CD has been inserted or an

inserted Audio CD is not readable.

•It is possible that CDs protected by copyright and self-made CD-R and CD-RW

are not returned at all or only in certain circumstances.

•Please observe the following information for the MP3 operation ⇒page 20.

•Please comply with the national legal copyright requirements in your country.

Main menu MEDIA

Main menu MEDIA - Overview



BAT-20H1065

Fig. 9 Main menu MEDIA: CD

mode

s36c.b.book Page 17 Thursday, April 9, 2009 2:50 PM

Range selector key MEDIA18

Calling up the main menu MEDIA and changing the media source

– Press the range selector key to switch to the main menu

MEDIA. The last used audio source will continue to play.

Buttons on the unit for controlling the current audio sources

The arrow keys on unit or will always affect the currently heard audio source,

irrespective of the current menu used.

- briefly press to go to the beginning of the current track, press repeatedly to

return to the beginning of the previous track.

- brief pressing changes over to the beginning of the next track.

When in the menu of the currently played audio source it is also possible to change

titles using the setting up button.

- by briefly pressing, you can select the display for the additional information of

the audio sources.

Selectable audio sources in the menu AUDIO

CD - changes over to an inserted CD.

CD 1-6* - changes over to a connected external CD changer.

SD card - changes over to an inserted memory card.

, or * - changes over to a connected external audio source.

Operating an externally connected audio source is possible, with certain restric-

tions, via the radio navigation unit and depends largely on the type of the connec-

tion.

Additional function keys in the AUDIO menu

- opens a pop-up window where the random play function Mix, the auto-

matic play Scan or the replay of the track or the folder can be started.

- opens the list of the tracks for the current audio source in order to select

another track.

Inserting or ejecting a CD

Inserting the CD

– Push a CD with the written side facing up as far as possible into the CD

case until it is automatically drawn in. The play function will start auto-

matically.

Taking out the CD

– Press the button to move the CD in the internal CD drive into the

Eject position.

If a CD is not taken out in the initial position, it will be reinserted after approximately

10 seconds for safety reasons.

Inserting or removing a memory card

Inserting a memory card

– Push the memory card into the memory card case with the trimmed

edge to the front top, until it is locked in position. The play function will

start automatically.

Taking out a memory card

– Press the button and then the function key .

BAT-20H1066

Fig. 10 Selectable sources in

the menu MEDIA

MEDIA

 





AUX MDI BT audio

Extras

Select



SETUP System

s36c.b.book Page 18 Thursday, April 9, 2009 2:50 PM

Page is loading ...

SKODA RNS 310 Skoda Amundsen Owner's manual

Brand: SKODA

Model: RNS 310 Skoda Amundsen

Category: Car video systems

Type: Owner's manual

This manual is also suitable for

Download PDF

report

SKODA RNS 310 Skoda Amundsen Owner's manual

This manual is also suitable for

SKODA RNS 310 Skoda Amundsen Owner's manual

Related papers