Dodge 2007 Power Wagon User manual

2007 OWNER’ S MANUAL

2007 POWER WAGON

81-326-0724 First Edition Printed in U.S.A.

TABLE OF CONTENTS

SECTION PAGE

1

INTRODUCTION

.............................................................3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

..............................9

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

..............................73

4

UNDERSTANDING YOUR INSTRUMENT PANEL

...................................167

5

STARTING AND OPERATING

.................................................241

6

WHAT TO DO IN EMERGENCIES

..............................................365

7

MAINTAINING YOUR VEHICLE

...............................................381

8

MAINTENANCE SCHEDULES

..................................................445

9

IF YOU NEED CONSUMER ASSISTANCE

.........................................465

10

INDEX

....................................................................473

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

m Introduction ...........................4

m How To Use This Manual ..................4

m Warnings And Cautions ...................6

m Van Conversions/Campers .................6

m Vehicle Identification Number ...............6

m Vehicle Modifications / Alterations ...........7

1

INTRODUCTION

This manual has been prepared with the assistance of

service and engineering specialists to acquaint you with

the operation and maintenance of your new vehicle. It is

supplemented by a Warranty Information Booklet and

various customer oriented documents. You are urged to

read these publications carefully. Following the instruc-

tions and recommendations in this manual will help

assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored

in the vehicle for convenient reference and remain with

the vehicle when sold, so that the new owner will be

aware of all safety warnings.

When it comes to service, remember that your dealer

knows your vehicle best, has the factory-trained techni-

cians and genuine Mopart parts, and is interested in

your satisfaction.

WARNING!

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals

known to the State of California to cause cancer and

birth defects or other reproductive harm. In addition,

certain fluids contained in vehicles and certain prod-

ucts of component wear contain or emit chemicals

known to the State of California to cause cancer and

birth defects or other reproductive harm.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section

contains the information you desire.

The detailed index, at the rear of this manual, contains a

complete listing of all subjects.

Consult the following table for a description of the

symbols that may be used on your vehicle or throughout

this owner’s manual:

4 INTRODUCTION

INTRODUCTION 5

1

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating

procedures which could result in an accident or bodily

injury. It also contains CAUTIONS against procedures

which could result in damage to your vehicle. If you do

not read this entire manual you may miss important

information. Observe all Warnings and Cautions.

VAN CONVERSIONS/CAMPERS

The Manufacturer’s Warranty does not apply to body

modifications or special equipment installed by van

conversion/camper manufacturers/ body builders. See

the Warranty information book, Section 2.1.C. Such

equipment includes video monitors, VCRs, heaters,

stoves, refrigerators, etc. For warranty coverage and

service on these items, contact the applicable manufac-

turer.

Operating instructions for the special equipment in-

stalled by the conversion/camper manufacturer should

also be supplied with your vehicle. If these instructions

are missing, please contact your selling dealer for assis-

tance in obtaining replacement documents from the

applicable manufacturer.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number (VIN) is found on the

left front corner of the instrument panel, visible through

the windshield. This number also appears on the Auto-

mobile Information Disclosure Label affixed to a window

on your vehicle, the vehicle registration and title.

6 INTRODUCTION

NOTE: It is illegal to remove the VIN.

VEHICLE MODIFICATIONS / ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle

could seriously affect its roadworthiness and safety

and may lead to an accident resulting in serious

injury or death.

Vehicle Identification Number

INTRODUCTION 7

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

m Power Wagon: Things To Know Before Starting

Your Vehicle ...........................12

▫ Features .............................12

▫ Instrument Panel And Controls ............12

▫ Operation ............................12

▫ Emergencies ..........................12

m A Word About Your Keys ..................12

▫ Ignition Key Removal ...................13

▫ Locking Doors With The Key ..............15

m Steering Wheel Lock — If Equipped ..........15

▫ If You Wish To Manually Lock The Steering

Wheel ..............................15

▫ To Release The Steering Wheel Lock .........15

▫ Automatic Transmission Ignition Interlock

System ..............................16

m Sentry Key — If Equipped .................16

▫ Replacement Keys ......................17

▫ Customer Key Programming ..............17

▫ General Information ....................18

2

m Security Alarm System — If Equipped .........18

▫ Rearming Of The System .................19

▫ To Set The Alarm ......................19

▫ To Disarm The System ...................19

m Illuminated Entry System — If Equipped .......20

m Remote Keyless Entry — If Equipped .........20

▫ To Unlock The Doors ...................21

▫ To Lock The Doors .....................21

▫ Using The Panic Alarm ..................22

▫ General Information ....................23

▫ Transmitter Battery Service ...............23

m Remote Starting System — Gas Engine Only ....24

m Door Locks ............................26

▫ Manual Door Locks .....................26

▫ Power Door Locks — If Equipped ..........26

▫ Child Protection Door Lock ...............29

m Windows .............................31

▫ Power Windows—If Equipped .............31

▫ Wind Buffeting ........................32

m Occupant Restraints ......................33

▫ Lap/Shoulder Belts .....................34

▫ Adjustable Upper Shoulder Belt Anchorage ....41

▫ Automatic Locking Restraint (ALR) Mode – If

Equipped ............................42

▫ Center Lap Belts .......................42

▫ Seat Belt Pretensioners ...................43

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ Enhanced Driver Seat Belt Reminder System

(BeltAlert) ...........................43

▫ Seat Belts And Pregnant Women ............45

▫ Seat Belt Extender ......................45

▫ Driver And Right Front Passenger Supplemental

Restraint System (SRS)—Airbag ............45

▫ Event Data Recorder (EDR) ...............56

▫ Child Restraint ........................58

m Engine Break-In Recommendations ...........70

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

2

POWER WAGON: THINGS TO KNOW BEFORE

STARTING YOUR VEHICLE

Your Power Wagon is a specialty vehicle, equipped with

several features not available on other production trucks.

It is very important that you read the following sections

of the owner’s manual before operation.

Features

(See page 78 for more information.)

Instrument Panel and Controls

(See page 171 for more information.)

Operation

(See page 264 for more information.)

Emergencies

(See page 366 for more information.)

A WORD ABOUT YOUR KEYS

The dealer that sold you your new vehicle has the key

code numbers for your vehicle locks. These numbers can

be used to order duplicate keys from your dealer. Ask

your dealer for these numbers and keep them in a safe

place.

Ignition Key

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Ignition Key Removal

Automatic Transmission

Place the shift lever in PARK. Turn the ignition switch to

the LOCK position, and remove the key.

NOTE: If you try to remove the key before you place the

lever in PARK, the key may become trapped temporarily

in the ignition cylinder. If this occurs, rotate the key to the

right slightly, then remove the key as described. If a

malfunction occurs, the system will trap the key in the

ignition cylinder to warn you that this safety feature is

inoperable. The engine can be started and stopped but

the key cannot be removed until you obtain service.

NOTE: The power window switches, radio, power

sunroof (if equipped), and power outlets will remain

active for 10 minutes after the ignition switch is turned

off. Opening either front door will cancel this feature.

Ignition Switch Positions

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

WARNING!

Never leave children alone in a vehicle. Leaving

children in a vehicle unattended is dangerous for a

number of reasons. A child or others could be

seriously or fatally injured. Don’t leave the keys in

the ignition. A child could operate power windows,

other controls, or move the vehicle.

CAUTION!

An unlocked car is an invitation to thieves. Always

remove key from the ignition and lock all doors

when leaving the vehicle unattended.

Manual Transmission—If Equipped

When the steering wheel is in the LOCK position, the

steering and ignition systems are locked to provide

antitheft protection for your vehicle. It may be difficult to

turn the key from the LOCK position when starting your

vehicle. Move the steering wheel left and right while

turning the key until it turns easily. To remove the key,

depress and hold the release button located between the

ignition switch and the instrument panel. Turn the igni-

tion key to LOCK and remove the key.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Locking Doors With The Key

You can insert the key with either side up. To lock the

door, turn the key rearward, to unlock the door, turn the

key forward. See Section 7 of this manual for door lock

lubrication.

STEERING WHEEL LOCK — IF EQUIPPED

Your vehicle may be equipped with a passive steering

wheel lock. This lock prevents steering the vehicle with-

out the ignition key. If the steering wheel is moved no

more than 1/2 turn in either direction and the key is not

in the ignition switch, the steering wheel will lock.

If You Wish To Manually Lock The Steering

Wheel:

With the engine running, turn the steering wheel upside

down, turn off the engine and remove the key. Turn the

steering wheel slightly in either direction until the lock

engages.

To Release The Steering Wheel Lock:

Insert the key in the ignition switch and start the engine.

If the key is difficult to turn, move the wheel slightly to

the right or left to disengage the lock.

Ignition Switch Positions

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

NOTE: If you turned the wheel to the right to engage

the lock, you must turn the wheel slightly to the right to

disengage it. If you turned the wheel to the left to engage

the lock, turn the wheel slightly to the left to disengage it.

Automatic Transmission Ignition Interlock System

This system prevents the key from being removed unless

the shift lever is in PARK. It also prevents shifting out of

PARK unless the key is in the ON positions, and the

brake pedal is depressed.

SENTRY KEY — IF EQUIPPED

The Sentry Key Immobilizer System prevents unautho-

rized vehicle operation by disabling the engine. The

system does not need to be armed or activated. Operation

is automatic, regardless of whether the vehicle is locked

or unlocked.

The system uses ignition keys, which have an embedded

electronic chip (transponder), to prevent unauthorized

vehicle operation. Therefore, only keys that are pro-

grammed to the vehicle can be used to start and operate

the vehicle. The system will shut the engine off in two (2)

seconds if someone uses an invalid key to start the

engine.

NOTE: A key, which has not been programmed, is also

considered an invalid key even if it is cut to fit the

ignition lock cylinder for that vehicle.

During normal operation, after turning on the ignition

switch, the Vehicle Security Alarm Indicator Light will

turn on for three (3) seconds for a bulb check. If the light

remains on after the bulb check, it indicates that there is

a problem with the electronics. In addition, if the light

begins to flash after the bulb check, it indicates that

someone used an invalid key to start the engine. Either of

these conditions will result in the engine being shut off

after two (2) seconds.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

If the Vehicle Security Alarm Indicator Light turns on

during normal vehicle operation (vehicle running for

longer than 10 seconds), it indicates that there is a fault in

the electronics. Should this occur, have the vehicle ser-

viced as soon as possible.

Replacement Keys

NOTE: Only keys that have been programmed to the

vehicle electronics can be used to start the vehicle. Once

a Sentry Key has been programmed to a vehicle, it cannot

be programmed to any other vehicle.

At the time of purchase, the original owner is provided

with a four digit PIN. This number is required for dealer

replacement of keys. Duplication of keys may be per-

formed at an authorized dealer or by using the Customer

Key Programming procedure. This procedure consists of

programming a blank key to the vehicle electronics. A

blank key is one which has never been programmed and

needs to be cut.

NOTE: When having the Sentry Key System serviced,

bring all vehicle keys to the dealer.

Customer Key Programming

You can program new keys to the system if you have two

valid keys by doing the following:

1. Cut the additional Sentry Key Transponder blank(s) to

match the ignition switch lock cylinder key code.

2. Insert the first valid key into the ignition switch and

turn the ignition switch ON for at least 3 seconds but no

longer than 15 seconds. Turn the ignition switch OFF and

remove the first key.

3. Insert the second valid key and turn the ignition

switch ON within 15 seconds. After ten seconds a chime

will sound and the Vehicle Theft Alarm Indicator Light

will begin to flash. Turn the ignition switch OFF and

remove the second key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2

4. Insert a blank Sentry Key into the ignition switch and

turn the ignition switch ON within 60 seconds. After 10

seconds a single chime will sound and the Vehicle Theft

Alarm Indicator Light will stop flashing, turn on again

for 3 seconds, and then turn off.

The new Sentry Key has been programmed. The Keyless

Entry Transmitter will also be programmed during this

procedure. Repeat this procedure to program up to a

total of 8 keys. If you do not have a programmed sentry

key, contact your dealer for details.

NOTE: If a programmed key is lost, see your dealer to

have all remaining keys erased from the systems

memory. This will prevent the lost key from starting your

vehicle. The remaining keys must then be repro-

grammed. All vehicle keys must be taken to the dealer at

the time of service to be reprogrammed.

General Information

The Sentry Key system complies with FCC rules part 15

and with RSS-210 of Industry Canada. Operation is

subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be

received, including interference that may cause undes-

ired operation.

SECURITY ALARM SYSTEM — IF EQUIPPED

This system monitors the vehicle doors and ignition for

unauthorized operation. When the alarm is activated, the

system provides both audible and visual signals. For the

first 3 minutes the horn will sound and the headlights

and security telltale will flash repeatedly. For an addi-

tional 15 minutes only the headlights and security telltale

will flash. The engine will run only if a valid Sentry Key

is used to start the vehicle. Use of the Sentry Key will

disable the alarm.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Rearming of the System:

The security system will rearm itself after the 15 addi-

tional minutes of headlights and security telltale flashing,

if the system has not been disabled. If the condition

which initiated the alarm is still present, the system will

ignore that condition and monitor the remaining doors

and ignition.

To Set the Alarm:

The alarm will set when you use the power door locks, or

use the Keyless Entry transmitter to lock the doors. After

all the doors are locked and closed the SECURITY light in

the instrument cluster will flash rapidly to signal that the

system is arming. The security light in the instrument

panel cluster will flash rapidly for about 16 seconds to

indicate that the alarm is being set. After the alarm is set,

the security light will flash at a slower rate to indicate

that the system is armed.

NOTE: If the SECURITY light stays on continuously

during vehicle operation, have the system checked by

your dealer.

To Disarm the System:

Use the Keyless Entry transmitter to unlock the door. If

something has triggered the system in your absence, the

horn will sound three times when you unlock the doors

and the security lamp will flash for 30 seconds. Check the

vehicle for tampering.

The Security system will also disarm, if the vehicle is

started with a programmed Sentry Key. If an unpro-

grammed Sentry Key is used to start a vehicle, the engine

will run for 2 seconds and then the security alarm will be

initiated. To exit alarming mode, press the transmitter

Unlock button, or start the vehicle with a programmed

Sentry Key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

2

Page is loading ...

Dodge 2007 Power Wagon, 2007 Ram 2500, RAM, Ram 2500 User manual