Marvel MP48SS2NP Installation guide

Installation

Instructions

Side-by-Side

Refrigerator

MP42SS2

MP48SS2

2

Table of Contents

Warnings and Important Information _____________________________________________3

Dimensions & Speciﬁ cations (Professional 42” & 48”)______________________________ 6

Dimensions & Speciﬁ cations (Professional 42” & 48” with

ﬂ ush mount trim) _________________________________________________________8

Cutout Dimensions (42”) ______________________________________________________ 10

Anti-Tip Dimensions (42”) _____________________________________________________ 11

Cutout Dimensions (48”) ______________________________________________________ 12

Anti-Tip Dimensions (48”) _____________________________________________________ 13

Cabinet Information __________________________________________________________ 14

Cabinet Information (with ﬂ ush mount trim) _____________________________________ 15

Custom Side Panel Dimensions ________________________________________________ 16

Custom Side Panel Dimensions (with ﬂ ush mount trim) ___________________________ 17

Custom Door Panel Dimensions _______________________________________________ 18

Custom Door Panel Installation ________________________________________________ 19

General Information __________________________________________________________ 21

Unpacking & Moving _________________________________________________________ 22

Flush Mount Side Trim Installation _____________________________________________ 23

Installation __________________________________________________________________ 23

Hinge Adjustment ________________________________________________________ 24

Kickplate Installation ______________________________________________________ 26

Door Stop Adjustment ____________________________________________________ 27

System Speciﬁ cations and Data ____________________________________________ 28

Final Installation__________________________________________________________ 29

Performance Checklist ________________________________________________________ 30

Control Panels _______________________________________________________________ 32

Service & Registration ________________________________________________________ 33

33

IMPORTANT – Please Read and Follow!

• Make sure that incoming voltage is the

same as unit rating. An electric rating

plate specifying voltage, frequency,

wattage, amperage, and phase is attached

to the product.

• To reduce the risk of ﬁ re, electrical shock,

or injury to persons, installation work and

electrical wiring must be done by a

qualiﬁ ed technician in accordance with all

applicable codes and standards, including

ﬁ re-rated construction.

• The installer should leave these

instructions with the consumer who should

retain them for local inspector’s use and

for future reference.

DANGER

WARNING

You will be killed or seriously injured if

you don't follow instructions.

You can be killed or seriously injured if

you don't follow instructions.

All safety messages will identify the

hazard, tell you how to reduce the chance

of injury, and tell you what can happen if

the instructions are not followed.

Your safety and the safety of others is

very important.

We have provided many important safety

messages in this manual and on your

appliance. ALWAYS read and obey all

safety messages.

This is the safety alert symbol. This

symbol alerts you to hazards that

can kill or hurt you and others.

All safety messages will be preceded

by the safety alert symbol and the word

“DANGER” or “WARNING.” These

words mean:

4

IMPORTANT – Please Read and Follow!

A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local

laws, or local ordinances.

• The required use of a GFI is normally related to the location of a receptacle with respect to

any signiﬁ cant sources of water or moisture.

• AGA Marvel will NOT warranty any problems resulting from GFI outlets which are not

installed properly or do not meet the requirements below.

If the use of a GFI is required, it should be:

• Of the receptacle type (breaker type or portable type NOT recommended)

• Used with permanent wiring only (temporary or portable wiring NOT recommended)

• On a dedicated circuit (no other receptacles, switches or loads in the circuit)

• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT

recommended)

• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)

• In good condition and free from any loose-ﬁ tting gaskets (if applicable in outdoor situations)

• Protected from moisture (water, steam, high humidity) as much as reasonably possible

5

WARNING

TIP OVER HAZARD

Appliance is top heavy

and tips easily when not

completely installed. Keep

doors closed until appliance

is completely installed and secured per

installation instructions.

Use two or more people to move and

install appliance. Failure to do so can

result in death or serious injury.

WARNING

ELECTRICAL SHOCK

HAZARD

Disconnect power or turn

power disconnect switch to

OFF position before removing top grille.

Failure to do so can result in death or

electrical shock.

IMPORTANT – Please Read and Follow!

Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent

tipping. Use cardboard shipping material or plywood under unit until it is installed in the

operating position to protect ﬂ oor surface.

It is your responsibility to:

• comply with installation speciﬁ cations and dimensions.

• properly install unit.

• remove any moldings or decorative panels that prevent the unit from being serviced.

• make sure that you have these materials (not provided with your unit), which are necessary

for proper installation:

• 1/4” (6 mm) copper tubing with shutoff valve

• 6– #8 x 3” (7.6 cm) wood screws (longer screws may be required)

• 1– Saddle valve (do not use self-piercing feature of the valve)

• assure that ﬂ oor will support unit, door panels and contents (approximately

1200 pounds [540 kg]).

• provide a properly grounded electrical outlet.

• assure that location will permit appliance doors to open 90º minimum.

6

Dimensions (Side-By-Side)

26-1/4”

(66.7 cm)

41”

(104.1 cm)

75–15/16”

(192.9 cm

)

3–19/32”

(9.1 cm)

42”

(106.7 cm)

9–5/32”

(23.3 cm)

82–3/4”

(210.2 cm)

min.

to

84–1/16”

(213.5 cm)

max.

23–7/8”

(60.6 cm)

24-5/8”

(62.6 cm)

26-1/4”

(66.7 cm)

47”

(119.4 cm)

75–15/16”

(192.9 cm

)

3–19/32”

(9.1 cm)

48”

(121.9 cm)

9–5/32”

(23.3 cm)

82–3/4”

(210.2 cm)

min.

to

84–1/16”

(213.5 cm)

max.

23–7/8”

(60.6 cm)

1–1/2”

(3.8 cm)

24-5/8”

(62.6 cm)

28”

(71.1 cm)

1–1/2”

(3.8 cm)

28”

(71.1 cm)

42” Side-By Side

48” Side-By Side

Top View

23-7/8”

(60.6 cm)

26-1/4”

(66.7 cm)

28”

(71.1 cm)

7

Speciﬁ cations (Side-By-Side)

48” Side-By-Side

Description MP48SS2

Overall width 48” (121.9 cm)

Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.

Overall depth from rear To front edge of side trim: 23-3/4 (60.3 cm)

To front of top grille: 26-1/4” (66.7 cm)

To front of handle endcap: 28” (71.1 cm)

Cutout width 47-5/8” (121.0 cm) min. to 47-3/4” (121.3 cm) max.

Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.

Standard Cutout depth 24” (61.0 cm) min.

Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product

Maximum amp usage 9.9 amps

Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi

Overall interior dimensions

Refrigerator

Freezer

Total capacity

19.49 cu. ft. (552 liters)

9.56 cu. ft. (271 liters)

29.05 cu. ft. (823 liters)

Approximate shipping weight 580 lbs. (263 kg)

42” Side-By-Side

Description MP42SS2

Overall width 42” (106.7 cm)

Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.

Overall depth from rear To front edge of side trim: 23-3/4 (60.3 cm)

To front of top grille: 26-1/4” (66.7cm)

To front of handle endcap: 28” (71.1 cm)

Cutout width 41-5/8” (105.7 cm) min. to 41-3/4” (106 cm) max.

Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.

Standard Cutout depth 24” (61.0 cm) min.

Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product

Maximum amp usage 9.9 amps

Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi

Overall interior dimensions

Refrigerator

Freezer

Total capacity

15.76 cu. ft. (446 liters)

9.56 cu. ft. (271 liters)

25.32 cu. ft. (717 liters)

Approximate shipping weight 525 lbs. (238 kg)

8

Dimensions

(Flush Mount Trim and Custom Door Overlay)

42” Side-By Side

with Flush Mount Trim

26-1/4”

(66.7 cm)

41”

(104.1 cm)

75–15/16”

(192.9 cm

)

3–19/32”

(9.1 cm)

42”

(106.7 cm)

9–5/32”

(23.3 cm)

82–3/4”

(210.2 cm)

min.

to

84–1/16”

(213.5 cm)

max.

23-7/8”

(60.6 cm)

24–5/8”

(62.6 cm)

26-1/4”

(66.7 cm)

47”

(119.4 cm)

75–15/16”

(192.9 cm

)

3–19/32”

(9.1 cm)

48”

(121.9 cm)

9–5/32”

(23.3 cm)

82–3/4”

(210.2 cm)

min.

to

84–1/16”

(213.5 cm)

max.

23-7/8”

(60.6 cm)

1–1/2”

(3.8 cm)

24–5/8”

(62.6 cm)

28”

(71.1 cm)

1–1/2”

(3.8 cm)

28”

(71.1 cm)

48” Side-By Side

with Flush Mount Trim

Top View

25-1/2”

(64.8 cm)

26-1/4”

(66.6 cm)

28”

(71.1 cm)

9

Speciﬁ cations

(Flush Mount Trim and Custom Door Overlay)

48” Side-By-Side Flush Mount Trim and Custom Door Overlay

Description MP48SS2 Flush Mount MP48SS2 Full Overlay

Overall width 48” (121.9 cm)

Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.

Overall depth from rear To front edge of side trim: 25-1/5" (64.8 cm)

To front of top grille: 26-1/4” (66.7 cm)

To front of handle endcap: 28” (71.1 cm)

Cutout width 48” (121.9 cm)

Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.

Flush Mount Cutout depth 26-1/2” (67.3 cm) min.

Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product

Maximum amp usage 9.9 amps

Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi

Overall interior dimensions

Refrigerator

Freezer

Total capacity

19.49 cu. ft. (552 liters)

9.56 cu. ft. (271 liters)

29.05 cu. ft. (823 liters)

Approximate shipping weight 580 lbs. (263 kg)

42” Side-By-Side Flush Mount Trim and Custom Door Overlay

Description MP42SS2 Flush Mount MP42SS2 Full Overlay

Overall width 42” (106.7 cm)

Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.

Overall depth from rear To front edge of side trim: 25-1/2" (64.8)

To front of top grille: 26-1/4” (66.7 cm)

To front of handle endcap: 28” (71.1 cm)

Cutout width 42” (106.7 cm)

Cutout height 82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.

Flush Mount Cutout depth 26-1/2” (67.3 cm) min.

Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product

Maximum amp usage 9.9 amps

Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi; maximum 120 psi

Overall interior dimensions

Refrigerator

Freezer

Total capacity

15.76 cu. ft. (446 liters)

9.56 cu. ft. (271 liters)

25.32 cu. ft. (717 liters)

Approximate shipping weight 525 lbs. (238 kg)

10

Cutout Dimensions

9”

(22.9 cm)

73-3/8”

(186.4 cm)

82–7/8”

(210.5 cm) min.

anti-tip board &

opening height

84–1/16”

(213.5 cm) max.

anti-tip board &

opening height

41–5/8”

(105.7 cm) min.

to

41–3/4”

(106.0 cm) max.

42”

(106.7 cm)

Flush Mount only

Standard Mount

24”

(61.0 cm)

Flush Mount

26-1/2”

(67.3 cm)

Electric Outlet Location

Water Line Entry Area

6–3/4”

(17.1 cm)

7–5/8”

(19.4 cm)

3”

(7.6 cm)

5/8”

(1.6 cm)

5/8”

(1.6 cm)

10–1/2”

(26.7 cm)

5/8”

(1.6 cm)

10–3/4”

(27.3 cm)

1”

(2.5 cm)

3–5/8”

(9.2 cm)

Optional floor

water line entry

42”

(106.7 cm)

Flush Mount only

41–5/8”

(105.7 cm)

See Anti-Tip board installation

6”

(15.2 cm)

9”

(22.9 cm)

42” Side-By-Side

11

Anti-Tip Dimensions

One 2”x 4” Mounting Board

3” (7.6 cm) x 3-1/2” (8.9 cm)

NOTE: If unit is installed deeper than

24” (61.0 cm), then shim behind the mounting

board by the difference.

Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.

NOTE: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

79–3/8”

(201.6 cm) min.

to bottom of

anti-tip board

80–1/2”

(204.6 cm) max.

to bottom of

anti-tip board

35”

(88.9 cm)

3–1/2”

(8.9 cm)

1.5”

(3.8 cm)

42” Side-By-Side

12

Cutout Dimensions

48” Side-By-Side

Standard Mount

24”

(61.0 cm)

Flush Mount

26-1/2”

(67.3 cm)

9”

(22.9 cm)

73-3/8”

(186.4 cm)

82–7/8”

(210.5 cm) min.

anti-tip board &

opening height

84–1/16”

(213.5 cm) max.

anti-tip board &

opening height

47–5/8”

(121.0 cm) min.

to

47–3/4”

(121.2 cm) max.

48”

(121.9 cm)

Flush Mount only

Electric Outlet Location

Water Line Entry Area

6–3/4”

(17.1 cm)

7–5/8”

(19.4 cm)

3”

(7.6 cm)

5/8”

(1.6 cm)

5/8”

(1.6 cm)

10–1/2”

(26.7 cm)

5/8”

(1.6 cm)

10–3/4”

(27.3 cm)

1”

(2.5 cm)

3–5/8”

(9.2 cm)

Optional floor

water line entry

47–5/8”

(121.0 cm)

48”

(121.9 cm)

Flush Mount only

See Anti-Tip board installation

6”

(15.2 cm)

9”

(22.9 cm)

13

Anti-Tip Dimensions

48” Side-By-Side

NOTE: If unit is installed deeper than

24” (61.0 cm), then shim behind the mounting

board by the difference.

One 2”x 4” Mounting Board

1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)

Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.

NOTE: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

79–3/8”

(201.6 cm) min.

to bottom of

anti-tip board

80–1/2”

(204.6 cm) max.

to bottom of

anti-tip board

41”

(104.1 cm)

3–1/2”

(8.9 cm)

1-1/2”

(3.8 cm)

14

Cabinet Information

For installation in 24" (61.0 cm) deep cabinets, the door face protrudes 2-3/4” (7.0 cm) from the

cabinet face. The handle protrudes an additional 2-15/16” (7.5 cm) into the room.

23-3/4”

(60.3 cm)

26-1/4”

(66.7 cm)

Face of

stainless steel door

24”

(61.0 cm)

24-3/4”

(62.9 cm)

Face of

door/drawer

Finished

Wall

Face of

cabinet

frame

Standard

Side trim

2-3/8”

(6.0 cm)

3/4”

(.6 cm)

1/4”

(0.6 cm)

27/32”

(0.2 cm)

42” (106.7 cm)

48” (121.9 cm)

41” (104.1 cm)

47” (119.4 cm)

* Refrigerator foam cabinet

can vary in de

p

th +/- 1/8” (0.3 cm)

Standard Mount Installation

1515

Cabinet Information ( with Flush Mount Trim)

23-7/8”

(60.6 cm)

24-5/8”

(62.5 cm)

26-1/4”

(66.7 cm)

26-1/2”

(67.3 cm)

Face of

stainless steel door

25-5/8”

(65.1 cm)

Face of

door/drawer

Finished

Wall

Face of

cabinet

frame

26-3/8”

(67.0 cm)

Flush

Side trim

3/4”

(.6 cm)

*

*The face of the door skin needs to be on the same plane, flush with the cabinets.

If the door face is pushed in past the surface of the cabinet, the door could run into

cabinetry when it is in the full open position.

The hinge stop needs to be placed at 90 or 110 degrees.

24”

(61.0 cm)

Face of

door/drawer

Finished

Wall

Face of

cabinet

frame

24-3/4”

(62.9 cm)

Flush

Side trim

3/4”

(.6 cm)

*

*The face of the door skin needs to be on the same plane, flush with the cabinets.

If the door face is pushed in past the surface of the cabinet, the door could run into

cabinetry when it is in the full open position.

The hinge stop needs to be placed at 90 or 110 degrees.

Offset in Finished Wall

1-3/4”

(4.4 cm)

23-7/8”

(60.6 cm)

24-5/8”

(62.5 cm)

26-1/4”

(66.7 cm)

26-1/2”

(67.3 cm)

1/4”

(0.25 cm)

1/8”

(0.3 cm)

1/2” (1.3 cm)

Flush Mount Installation with Standard Cabinets

Flush Mount Installation with Custom Cabinets

16

Custom Side Panel Dimensions

3/4”

(1.9 cm)

End panel

5/32”

(0.4 cm)

3/16”

(0.5 cm)

Back filler

panel

24-5/8”

(62.5 cm)

24-5/8”

(62.5 cm)

Optional kickplate

Notch dimensions

determined by cabinets

82-7/8”

(210.5 cm) min.

to

84-1/16”

(213.5 cm) max.*

82-7/8”

(210.5 cm) min.

to

84-1/16”

(213.5 cm) max.*

6”

(15.2 cm)

* Depending on how high

leveling feet are raised, and

cabinet enclosure height.

17

Custom Side Panel Dimensions

( with Flush Mount Trim)

* Depending on how high leveling

feet are raised, and cabinet enclosure

height.

3/4”

(1.9 cm)

End panel

1”

(2.5 cm)

1/4”

(0.6 cm)

Z-Bracket

23-7/8”

(60.6 cm)

23-7/8”

(60.6 cm)

Optional kickplate

Notch dimensions

determined by cabinets

82-7/8”

(210.5 cm) min.

to

84-1/16”

(213.5 cm) max.*

82-7/8”

(210.5 cm) min.

to

84-1/16”

(213.5 cm) max.*

26-3/8”

(67.0 cm)

26-3/8”

(67.0 cm)

Front of Stainless

steel door

Flush side trim

“Z” bracket

Custom Side

panel

23-7/8”

(60.6 cm)

24-5/8”

(62.5 cm)

26-1/4”

(66.7 cm)

26-1/2”

(67.3 cm)

25-1/2”

(64.7 cm)

Upper

Cabinets

12-3/4”

(32.4 cm)

12”

(30.5 cm)

3/4”

(1.9 cm)

Front edge of

standard depth

countertop

Hinge stop needs to

be 90 or 110

degrees

23-7/8”

(60.6 cm)

1/4”

(0.25 cm)

Top View - Assembled

18

Custom Door Panel Dimensions

28-5/16”

(71.9 cm)

75-1/2”

(191.8 cm)

3/4”

(1.9 cm)

18-11/16”

(47.5 cm)

3/4”

(1.9 cm)

22-13/16”

(57.9 cm)

75-1/2”

(191.8 cm)

3/4”

(1.9 cm)

3/4”

(1.9 cm)

18-3/16”

(46.2 cm)

42” Side-By-Side

48” Side-By-Side

Note: Panel overlays must be dry, solid,

straight one piece panels. The use of

multiple panel pieces to achieve the

dimensions is not recommended.

19

Custom Door Panel Installation

3

2-1/16”

(5.2 cm)

2-1/16”

(5.2 cm)

Back of panelBack of panel

FOL bracketFOL bracket“Z” bracket“Z” bracket

1-11/16”

(4.3 cm)

1-11/16”

(4.3 cm)

12-1/16”

(30.6 cm)

12-1/16”

(30.6 cm)

2-1/8”

(5.4 cm)

2-1/8”

(5.4 cm)

2-1/8”

(5.4 cm)

4

5

x13

6

Remove bracket. Measure and mark the ﬁ rst hole for each bracket.

Attach “Z” bracket to the hinge side of custom panel.

Attach bracket to the handle side of custom panel.

Push custom wood panel onto door.

1

x13

2

x13

x2

Remove handle side cabinet screws and trim

with a Phillips screwdriver from either the left or right

side door.

Remove all screws from handle side door trim.

Remove two screws from top and bottom door trim.

Remove handle side door trim.

20

Custom Door Panel Installation

9

x13

Reinstall cabinet trim and screws.

7

8

x13

x2

Slide custom wood panel to the hinge side, ensuring

“Z” bracket engages the door bracket.

Reinstall handle side door trim

and door trim screws.

Repeat same procedure for the other

side door panel.

Page is loading ...

Marvel MP48SS2NP Installation guide

This manual is also suitable for

Marvel MP48SS2NP Installation guide

in other languages

Related papers

Other documents