Thermaltake Flow TW Plus User manual
- Category
- Hardware cooling accessories
- Type
- User manual
O4468
REVISION A.2007.05
Please visit our Support Section for more technical support or update at
Flow TX Plus
P/N : CL-W0138
Flow meter with Water Temperature Indicator
Application with BigWater 735
120mm
Radiator
Copper
waterblock
Liquid
tank
Pump
Flow TX Plus
You can apply the Flow TX Plus to fit into any Thermaltake liquid cooling system.
Please visit our website at www.thermaltake.com.
The following diagrams are BigWater 735 with Flow TX Plus.
How to upgrade your BigWater series with Flow TX Plus >>
Install Flow TX Plus in
Thermaltake Armor
chassis with
BigWater 735
ON / OFF (A)
RESET (E)
RECORD (D)
Temp. Controller (C)
Oo
C/ F switch (B)
There are two temperature shown on the screen (T1, T2). T1 always mean pre-setting temperature
as well as T2 representatives the temperature from sensor.
(A)
(B
(C)
(D)
(E
ON / OFF:
oo
) C/ F :
Alarm set :
REC:
"REC"
) RESET:
power on or power off switch.
Celsius and Fahrenheit display switch.
Reset the alarm temp. Please adjust the pre-setting temperature by using
the cross-head screw driver.
Whatever it shows the temperature you would like to set, ( the screen
should be shown without MIN or MAX, see fig 1), please press the button
to record the temperature.
(MAX & MIN)
Show the highst and lowest temperature record.
D. How to install the Monitor >>
1. Power on the function:
- Press the ON/OFF button to start the alarm function of LCD panel.
2. Set the temperature:
- Set the temperature by turning the temp controller with the cross-head screw driver.
- The temperature you set will be shown on the panel remarked with alarm temp.
How to use the LCD Monitor >>
3. Monitor Switch:
When the screen is shown MAX
, it means the highest temperature you have recorded. In the
meanwhile, T1 is the highest temperature you set, T2 is the
highest temperature that the sensor detected.
Press "REC" Button
When the screen is shown MIN
, it means the lowest temperature you have recorded. In the
meanwhile, T1 is the lowest temperature you set, T2 is the
lowest temperature that the sensor detected.
Press "REC" Button
Normal Status
"MAX" Status
"MIN" Status
Note:
Note:
T1 is the highest alarm
temperature you set, T2
is the temperature that
the sensor detected
right now.
How to operate the LCD Monitor >>
O4618
O4468
REVISION A.2007.05
Please visit our Support Section for more technical support or update at
Components >>
Flow TX Plus
LCD Monitor
Velcro X 1
Install the LCD monitor >>
Install the tube with the Quick Install Connectors >>
>
Unscrew the nut
Insert the tube through the nut and tighten
it on the Flow TX Plus. Repeat the
installation steps for the other side.
NOTE: Before installing, please make sure that the connectors on Flow TX Plus are tightened properly.
>
Tear off one side of the
velcro and stick it on
the down side of
LCD monitor
Tear off the other side of the velcro and
stick it in a proper location inside the chassis
>
Connect the 2 pin
temperature sensor
from LCD monitor to
Flow TX Plus
Connect the 4-pin
power connector from
LCD monitor to
power supply.
>
Flow TX Plus
P/N : CL-W0138
Flow meter with Water Temperature Indicator
-
1
-
2
Thermaltake Flow TW Plus User manual
- Category
- Hardware cooling accessories
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Thermaltake PS-TPD-1200MPCGUS-1 click here.
-
-
-
-
-
-
-
-
-
Other documents
-
Danfoss ECL Comfort 300, card F11 Operating instructions
-
Philips M3046A User manual
-
Genie Z-80/60 Service and Repair Manual
-
Wintal Digital video recorder User Instruction Manual
-
Terex Genie S-120HD Service and Repair Manual
-
Volvo G930 User manual
-
Mindray Accutorr Plus User manual
-
Bacharach PGM-IR User manual
-
-
