OperatOr’s Manual
3 3 2 7
J D
WARNING
California Proposition 65
Cancer and Reproductive Harm – www.P65Warnings.ca.gov.
WARNING
Read and follow all safety rules and instructions in this manual before attempting to operate this machine.
Failure to comply with these instructions may result in personal injury.
Form No. 769-20394
(April 4, 2019)
Safe Operations Practices ...................................... 2
Assembly .................................................................. 7
Operation ................................................................. 9
Service and Maintenance ......................................12
Parts/Warranty .............. See Separate Supplement
Table of Contents
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all
models and the model depicted may differ from yours.
Battery-Powered Lithium-Ion Tractor
Record Product Information
Before setting up and operating your new equipment,
please locate the model plate on the equipment and
record the information in the provided area to the right.
You can locate the model plate by lifting up the seat
and looking under the seat pan. This information will be
necessary, should you seek technical support via our web
site or with your local authorized service dealer.
Model NuMber
Serial NuMber
2
SAFE OPERATION PRACTICES
General Information
1. Read, understand, and follow all instructions on the tractor and in the
manual(s) before attempting to assemble and operate. Keep this manual in a
safe place for future and regular reference and for ordering replacement parts.
2. Be familiar with all controls and their proper operation. Know how to stop the tractor
and disengage them quickly.
3. Never allow children under 14 years of age to operate this tractor. Children 14 and over
should read and understand the instructions and safe operation practices in this manual
and on the tractor and should be trained and supervised by an adult.
4. Never allow adults to operate this tractor without proper instruction.
5. If situations occur which are not covered in this manual, use care and good
judgment. Contact your customer service representative for assistance.
6. According to the U.S. Consumer Products Safety Commission (CPSC) and the
U.S. Environmental Protection Agency (EPA), this product has an estimated
useful life of seven (7) years, under ordinary use conditions. At the end of
its useful life, have the product inspected annually to ensure all mechanical,
electrical and safety systems are operating properly, safely, and are not worn
excessively. Failure to do so may result in accident, injury, or death.
Preparation Before Operating
1. Thoroughly inspect the area where the tractor is to be used. Remove all stones,
sticks, wire, bones, toys, and other foreign objects which could be picked up and
thrown by the blade(s). Thrown objects can cause serious personal injury.
2. To help avoid blade contact or a thrown object injury, keep bystanders,
helpers, children and pets at least 75 feet (23 meters) from the tractor while
it is in operation. Keep bystanders, children and pets inside during operation.
Stop tractor if anyone enters the area.
3. Be aware of the tractor discharge direction and do not point it at anyone.
4. Always wear safety glasses or safety goggles during operation and while
performing an adjustment or repair to protect your eyes. Thrown objects
which ricochet can cause serious injury to the eyes.
5. Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts.
Loose fitting clothes, jewelry and long hair can be caught in movable parts.
Never operate this tractor in bare feet or sandals.
6. Do not charge or operate the tractor in the rain or wet conditions.
7. Use only accessories and attachments approved for this tractor by the tractor
manufacturer. Read, understand and follow all instructions provided with
the approved accessory or attachment.
Operating
1. Data indicates that operators, age 65 years and above, are involved in a large
percentage of riding tractor-related injuries. These operators should evaluate
their ability to operate the riding tractor safely enough to protect themselves
and others from serious injury.
2. Set the parking brake before attempting to start the tractor.
3. Plan your mowing pattern to avoid discharge of material toward roads,
sidewalks, bystanders and the like. Also, avoid discharging material against
a wall or obstruction which may cause discharged material to ricochet back
toward the operator.
4. In case of a system fault or a complete loss of battery power, the tractor on a
hill can freewheel. Depress the brake pedal to maintain control and stop the
tractor. Restart the tractor. If the system fault problem persists, contact your
authorized service dealer.
5. Do not put hands or feet near rotating parts or under the cutting deck.
Contact with the blade(s) can amputate hands and feet.
6. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain
could overturn the tractor. Tall grass can hide obstacles.
7. Check overhead clearances carefully before driving under low hanging tree
branches, wires, door openings etc., where the operator may be struck or
pulled from the tractor, which could result in serious injury.
8. Never leave a running tractor unattended. Always turn off blade(s), set the
parking brake, press Start/Stop button, turn key to OFF position and remove
key before dismounting.
9. Turn off blade(s), set parking brake, press Start/Stop button and wait
until the blade(s) come to a complete stop before removing grass catcher,
emptying grass, unclogging chute, removing any grass or debris, or making
any adjustments.
10. Your tractor is designed to cut normal residential grass of a height no more
than 10” (25.4 cm). Do not attempt to mow through unusually tall, dry
grass (e.g., pasture) or piles of dry leaves. Dry grass or leaves may contact
hot surfaces and/or build up on the tractor deck presenting a potential fire
hazard.
11. Turn off blade(s) before traveling in reverse. Back up slowly. Always look
down and behind before and while backing to avoid a back-over accident.
12. Never carry passengers.
13. Stay at least 10 feet (3 meters) from drop-offs, ditches, embankments or
the edge of water. The tractor could suddenly turn over if a wheel is over the
edge of a cliff, ditch, or if an edge caves in.
WARNING
This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others.
Read and follow all instructions in this manual before attempting to operate this tractor. Failure to comply with these instructions may result in personal
injury. When you see this symbol, HEED ITS WARNING!
DANGER
This tractor was built to be operated according to the safe operation practices in this manual. As with any type of power equipment, carelessness or error
on the part of the operator can result in serious injury. This tractor is capable of amputating fingers, hands, toes and feet and throwing debris. Failure to
observe the following safety instructions could result in serious injury or death.
Lithium-Ion Battery System
Servicing requires extreme care and knowledge of the system and must be performed only by a qualified service technician. For repair or service take the tractor to your
nearest authorized service dealer. Always use original equipment manufacturer’s (OEM) replacement parts when servicing.
3
SAFE OPERATION PRACTICES
14. A missing or damaged chute deflector, mulch plug or entire grass catcher can
cause blade contact or thrown object injuries.
15. Do not operate the tractor without the chute deflector, mulch plug or entire
grass catcher in its proper place.
16. Use extra care with grass catchers or other attachments. These can change
the stability of the tractor. Always follow the attachment manufacturer’s
instructions.
17. Stop the blade(s) when crossing gravel drives, walks, or roads and while not
cutting grass.
18. Watch for traffic when operating near or crossing roadways. This tractor is not
intended for use on any public roadway.
19. Mow only in daylight or good artificial light.
20. Do not operate the tractor while under the influence of alcohol or drugs.
21. Slow down before turning. Operate the tractor smoothly. Avoid erratic
operation and excessive speed.
22. Motors may become hot and can cause serious burn injuries. Do not touch.
Allow the tractor to cool for five minutes before attempting any service.
23. Do not turn off tractor and freewheel downhill. Over-speeding may cause the
operator to lose control of the tractor resulting in serious injury or death.
Children
1. Tragic accidents can occur if the operator is not alert to the presence of
children. Children are often attracted to the tractor and the mowing activity.
They do not understand the dangers. Never assume that children will remain
where you last saw them.
2. Keep bystanders, children and pets inside during operation under the
watchful care of a responsible adult other than the operator. Stop the tractor
if anyone enters the area.
3. Never carry children, even with the blade(s) shut off. They may fall off and be
seriously injured or interfere with safe tractor operation. Children who have
been given rides in the past could suddenly appear in the mowing area for
another ride and be run over or backed over by the tractor.
4. Be alert and turn tractor off if a child or bystander enters the area.
5. To avoid back-over accidents, always look behind and down for small
children.
6. Use extreme care when approaching blind corners, doorways, shrubs, trees
or other objects that may block your vision of a child who may run into the
path of the tractor.
7. Never allow children under 14 years of age to operate this tractor. Children
14 and over should read and understand the instructions and safe operation
practices in this manual and on the tractor and should be trained and
supervised by an adult.
8. Do not allow any child to joy ride on the tractor. The tractor is not a toy or a
go-cart. Warn your children that the tractor can be dangerous and they must
stay away from it at all times.
9. Keep children away from a hot or running tractor. They can suffer burns from
hot motors.
10. Remove key when tractor is unattended to prevent unauthorized operation.
Make certain the key is inaccessible to small children.
Slope Operation
1. Slopes are a major factor related to loss of control and tip-over accidents which
can result in severe injury or death. All slopes require extra caution. If you
cannot back up the slope or if you feel uneasy on it, do not mow or drive on it.
2. For your safety, measure any slope before using the tractor on the sloped
area. Use a slope measuring device in addition to the slope gauge included
as part of this manual to measure slopes before operating this tractor on a
sloped or hilly area. Smart phone applications can be also utilized to measure
slopes. If the slope is greater than 12 degrees as shown on the slope gauge or
a slope measuring device, do not operate this tractor on that area or serious
injury could result.
3. Do not mow on slopes greater than 12 degrees (21%).
4. Do not mow across slopes, only mow up or down slopes that are less than 12
degrees (21%). Use low speeds and avoid sudden turns.
5. Do not mow on wet grass. Reduced traction could cause sliding or a loss of
control.
6. Do not operate tractor under any conditions where traction, steering or
stability is in question. Tires could slide even if the wheels are stopped.
7. Avoid starting and stopping on slopes. Avoid making sudden changes in
speed or direction. Make turns slowly and gradually.
8. Use extra care while operating tractor with grass catcher or other
attachment(s). They can affect the stability of the tractor. Do not use grass
catcher on slopes greater than 10 degrees (17%).
9. Do not try to stabilize the tractor by putting your foot on the ground.
10. Keep all movement on the slopes slow and gradual. Do not make sudden
changes in speed or direction. Rapid acceleration could cause the front of
the tractor to lift and rapidly tip over backwards, which could cause serious
injury or death.
11. Do not turn off tractor and freewheel downhill. Over-speeding may cause the
operator to lose control of the tractor resulting in serious injury or death.
Hauling
1. Use properly secured full width ramps for loading and unloading a tractor for
transport.
2. Use extra care when loading or unloading the tractor into a trailer or truck.
This tractor should not be driven up or down ramp(s), because the tractor
could tip over, causing serious personal injury. The tractor must be pushed
manually on ramp(s) to load or unload properly.
3. Raise the deck to the highest position for loading clearance.
4. Do not tow this tractor, damage to the drive motors can occur.
Towing with your tractor
1. Do not tow a load that exceeds 250 lbs (113kg) rolling weight and never exceed 50
lbs (22kg) tongue weight.
2. Do not attach towed equipment except at the hitch point of the tractor.
3. Never allow children or others in or on towed equipment.
4. Do not tow on slopes greater than 5 degrees (9%). On slopes, the weight of towed
equipment may cause loss of traction and loss of control and/or the ability to stop.
5. Always use extra caution when towing with a tractor capable of making tight
turns (e.g. tight-turn tractor). Make wide turns to avoid jack-knifing.
6. Travel slowly and allow extra distance to stop.
Service
1. Keep tractor in good working order. Do not use the tractor until worn or
damaged parts are replaced.
2. Tractor blade(s) are sharp. Wrap the blade or wear gloves, and use extra
caution when servicing them.
3. Remove key and store the tractor indoors when not in use. Allow the tractor
to cool at least five minutes before charging or storing.
4. Before cleaning, repairing, or inspecting, make certain the blade(s) and all
moving parts have stopped. Turn off tractor and remove the key.
4
SAFE OPERATION PRACTICES
5. Check to make sure the blades come to complete stop in not more than (5)
five seconds after disengaging the blade disengagement control per the
interval in the Maintenance Schedule. Measure the stopping time with a stop
watch. If the blades do not stop completely in less than five seconds, your
tractor should be serviced professionally by an authorized dealer.
6. Check the safety interlock system per the interval in the Maintenance
Schedule for proper function, as described later in this manual. If the safety
interlock system does not function properly, have your tractor serviced
immediately by an authorized dealer.
7. Never tamper with the safety interlock system or other safety devices. Check
their proper operation regularly.
8. Check the blade(s) mounting bolt torque in accordance to the Maintenance
Schedule in this manual. Also, visually inspect blade(s) for damage (e.g.,
excessive wear, bent, cracked). Replace the blade(s) with the original
equipment manufacturer’s (O.E.M.) blade(s) only.
9. Use of service parts which do not meet the original equipment specifications
may lead to improper performance and compromise safety.
10. Keep all nuts, bolts and screws tight to be sure the equipment is in safe
working condition. Review the Maintenance Schedule chart in this manual
for service interval information.
11. After striking a foreign object, stop the tractor, push the Start/Stop button,
turn the key to the OFF position and remove. Thoroughly inspect the tractor
for any damage. Repair the damage before operating.
12. To reduce fire hazard, keep the motor(s) free of grass, leaves and debris
build-up. Follow the post operation tractor care instructions in the Service
and Maintenance section.
13. Check brake operation frequently as it is subjected to wear during normal
operation. Adjust and service as required.
14. Never attempt to make adjustments or repairs to the tractor without
removing the key.
15. Maintain or replace safety and instruction labels, as necessary.
General Electric Safety
1. Do not expose the tractor to rain or wet conditions.
2. Do not service the tractor or handle electrical components with wet hands.
3. Do not operate the tractor in the rain, in wet conditions or on wet surfaces.
4. To reduce the risk of electric shock, avoid body contact with grounded
conductors, such as metal pipes or wire fences.
5. Do not operate the tractor in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust.
6. For protection against risk of injury or electric shock, do not replace blown
fuses. Your tractor should be serviced professionally by an authorized dealer.
7. Never douse or hose the tractor with water. Avoid getting any liquid in the
motors and electrical connections. Clean the tractor after each use. Refer to
cleaning and storage. Do not use solvents or strong detergents.
Battery Charger Safety
WARNING
Only use an OEM battery charger (part# 725-07253A) to charge the
batteries in this tractor. DO NOT attempt to charge any other batteries with
the battery charger specific to this tractor. Other types of batteries may
burst, causing fire, personal injury or property damage.
1. Recharge only with the charger specified by the manufacturer. A charger that
is suitable for one type of battery may create a risk of fire when used with
another battery.
2. Do not use the charger in the rain, wet locations or in the presence of
flammable liquids or gasses.
3. A nameplate on the charger indicates the voltage used. Never connect the
charger to an AC voltage that differs from this voltage.
4. An extension cord should not be used unless absolutely necessary. Use of
an improper extension cord could result in a risk of fire, electric shock or
electrocution.
5. Do not use multiple extension cords.
6. Make sure the extension cord is heavy enough to carry the current drawn by
the charger. An undersized extension cord will cause a drop in line voltage,
resulting in a loss of power and overheating. If in doubt, use the next heavier
gauge cord. The smaller the gauge number, the heavier the cord.
MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR 120 VOLT APPLIANCES USING 0-6
AMPS
Cord Length (ft.) 25 50 100 150
Wire Size (AWG) 16 16 16 14
7. Make sure the cords are in good condition. Inspect the battery charger power cord
and extension cord periodically. Look closely for deterioration, cuts or cracks in the
insulation. If either cord is damaged in any manner while plugged in, disconnect
the cord from both the outlet and the charger. Do not use a damaged cord.
Damaged cords should be repaired or replaced.
8. Do not abuse cords. Never pull or carry the charger by a cord. Keep cords
away from heat, oil, water, sharp edges, and moving objects. Always grasp
the plug when disconnecting a cord.
9. Never modify a plug, cord or outlet in any way.
10. Ground Fault Circuit Interrupter (GFCI) protection should be provided on the
circuit(s) or outlet(s) to be used with this charger. For an extra measure of safety, use
receptacles (outlets) with built-in GFCI protection.
11. Do not place the battery charger where cords might be stepped on, tripped
over or subjected to damage.
12. Keep the battery charger and cords in a cool and dry area.
13. Keep the battery charger and cords away from all liquids.
14. Do not allow small metal items or material such as steel wool, aluminum foil or
other foreign particles into the charger port.
15. Do not probe the charger with conductive material. There is a risk of electric
shock.
16. Do not cover the battery charger. The battery charger may overheat.
17. Do not allow the battery or battery charger to overheat. If they are warm,
allow them to cool down. Only charge batteries in temperatures between
32° and 104° F (0° and 40° C).
Battery Safety
1. Do not expose the battery to fire or to temperatures over 140º F (60º C).
Doing so could cause an explosion.
2. Handle battery with care. Do not short the battery with conductive
materials, such as rings, bracelets, keys, etc. Shorting the battery may cause
personal injury, damage to the battery or a fire.
3. Do not attempt to charge a cracked or damaged battery.
4. Do not use or charge a wet battery or a battery that shows any evidence of
corrosion.
5. Do not use a damaged or modified battery. Doing so could result in a fire,
explosion or personal injury.
6. Do not dispose of the battery in a fire. The cell may explode. Contact your local
authorized service dealer for proper battery recycling.
7. Exercise care in handling batteries in order not to short the battery with
conductive materials such as rings, bracelets, and keys. The battery or
conductor may be hot and cause burns.
5
SAFE OPERATION PRACTICES
WARNING
Your Responsibility—Restrict the use of this tractor to persons who read, understand and follow the warnings and instructions in this manual and on
the tractor.
SAVE THESE INSTRUCTIONS!
WARNING
• The battery may present a risk of fire or chemical burn if misused. Do
not disassemble, overheat or incinerate the battery.
• Leakage from the battery may occur under extreme usage, charging
or temperature conditions or if the battery is damaged, crushed or
punctured. This leakage indicates a failure of the battery and the
the battery should be properly disposed of by an authorized service
dealer.
If the battery leakage gets on your skin or eyes, follow these steps:
• Immediately wash the skin and flush the eyes with cool water for at least 20
minutes and seek immediate medical attention.
• Contents of open battery cells may cause respiratory irritation. Provide fresh
air. If symptoms persist, seek medical attention.
• Ventilate the room and vacate the area if smoke and gases are present. Gas
and smoke in a confined area will present a potential health risk.
If the leakage gets on your clothing or shoes, remove, isolate and wash the
contaminated clothing thoroughly.
SAFETY SYMBOLS
This page depicts and describes safety symbols that may appear on this product.
Read, understand, and follow all instructions on the tractor before attempting to
assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the
manual(s) before attempting to assemble and operate.
WARNING — THROWN OBJECTS
This tractor may pick up and throw objects which can
cause serious personal injury. Stay clear. Keep bystanders,
helpers, children and pets at least 75 feet from the tractor
while it is in operation.
WARNING — BYSTANDERS
Keep bystanders, helpers, children and pets at least 75
feet from the tractor while it is in operation.
DANGER — ROTATING BLADE(S)
Never carry passengers. Never carry children, even with
the blade(s) OFF.
WARNING — ROTATING BLADE(S)
Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate
hands and feet. Be sure blade(s) and power are off before
placing hands or feet near blade(s).
Symbol Description
WARNING — ROTATING BLADE(S)
Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate hands
and feet. Be sure blade(s) and power are off before placing
hands or feet near blade(s). Always remove the key when
not in use.
WARNING — SLOPE OPERATION
Go up and down slopes, not across. Use extra caution on
slopes. Do not mow or drive on slopes greater than 12°/21%.
If tractor stops going uphill, stop blade(s) and back down
slowly.
DANGER — SLOPE OPERATION
Do not operate this tractor where it could tip or slip. Avoid
sudden turns. Use low speed.
DANGER — ROTATING BLADE(S)
Always look down and behind before and while backing
to avoid a back-over accident. To avoid a back-over
accident, keep children away from the tractor while it is in
operation. Mowing in reverse is not recommended.
WARNING — THROWN OBJECTS
This tractor may pick up and throw objects which can
cause serious personal injury.
DANGER — GUARDS, SHIELDS, SWITCHES, ETC.
Keep safety devices (Guards, Shields, Switches, Etc.) in
place and working.
WARNING — ELECTRIC SHOCK
Do not charge tractor in rain or wet locations. Do not
operate tractor in rain.
WARNING — ELECTRIC SHOCK
Do not charge tractor in rain or wet locations. Do not
operate tractor in rain.
DANGER — SERVICE
Many components on this tractor should only be serviced
by an authorized service dealer. Read this Operator’s
Manual before attempting to service this tractor.
WARNING — STORE TRACTOR INDOORS
Store tractor indoors at all times when not in use.
(OK) (TOO STEEP)
USE THIS SLOPE GAUGE TO DETERMINE
IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!
To check the slope, proceed as follows:
1. Remove this page and fold along the dashed line.
2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.)
3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ).
4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2).
5. If there is a gap below the gauge, the slope is too steep for safe operation (See Figure 2 above).
12°/21% dashed line
Slope Gauge
Figure 2Figure 1
12°/21% Slope
12°/21% Slope
WARNING! Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death.
Do not operate machine on slopes in excess of 12 degrees/21 percent. All slopes require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow or drive on it. Always mow up and down slopes, never across the face of slopes.
SLOPE GAUGE
6
7
ASSEMBLY
Note: All references in this manual to the left or right side and front or back of the tractor
are from the operating position only. Exceptions, if any, will be specified.
Note: Some components may come already assembled. If they are already assembled, skip
ahead to the next step.
Preparation
Before beginning installation, remove all the contents from the crate and all the hardware
from the pack to make sure everything is present. Hardware is listed below.
Contents of Crate
• Tractor
• Steering Pedestal Cap
• Discharge Chute Assembly
• Hardware Bag
• Product Registration Card
• Operator’s Manual
• Mulch Plug
• Battery Charger
• Steering wheel/ Shaft Assembly
• Seat Assembly
• Front Bumper
• Battery Charger Manual
• Hardware Pack: Seat Mounting Bracket (w/ two shoulder bolts & lock nuts installed)
Recommended Tools for Assembly
• 1/4” or 3/8” drive ratchet
• 3/8” wrench and/or socket
• 7/16” wrench and/or socket
• 1/2” wrench and/or socket
• 9/16” wrench and/or socket
• Phillips screw driver
Manually Moving the Tractor
CAUTION
Never tow your tractor. Towing the tractor with the rear wheels on the ground may
cause severe damage to the drive motors.
The tractor can be moved as long as the parking brake is not set. The tractor can be pushed
slowly.
Installing the Steering Wheel
Assembly
1. Slide the pedestal cap (a) onto the
steering shaft (b) so that when the
steering shaft (b) is installed on the
tractor, the pedestal cap (a) will be
upright as shown in Figure 1.
2. Remove the shoulder bolt (c) and lock
nut (d) from the steering shaft and
retain for later steps. See Figure 2.
3. Position the steering wheel assembly
over the lower steering shaft on the
tractor. Align the steering wheel so
that its largest opening faces forward
when the tractor wheels are straight.
4. Lower the steering wheel assembly
(a) onto the lower steering shaft (b)
and secure with the shoulder bolt (c)
and lock nut (d) previously removed.
See Figure 2.
(b)
(a)
(a)
(b)
Figure 1
(d)
(c)
(a)
(b)
(d)
(c)
Figure 2
5. Tighten the shoulder bolt and lock nut
using a 9/16” wrench or socket and
7/16” wrench or socket.
6. Remove the pedestal cap mount screw
(factory installed) located on the tractor’s
steering console. Retain the screw for
later instructions. See Figure 3.
7. Connect the headlight wire terminals
(a). Slide the pedestal cap (b) down
onto the tractor and slightly rotate to
the right to clip into place. Secure the
pedestal cap (b) with the screw (c)
previously removed. See Figure 3.
Installing Operator’s Seat
1. Remove the shoulder bolts (a) and lock
nuts (b) from the seat mounting bracket
(c) included in your hardware pack. See
Figure 4.
2. Remove the two self-tapping bolts (a)
factory installed on the tractor. See Figure
5.
3. Align the seat bracket (a) in place over the holes from where the self-tapping bolts
(b) were removed, as shown in Figure 6.
4. Using a 1/4” drive ratchet with a 3/8” socket, secure the seat bracket (a) with the
self-tapping bolts (b) removed in step 2. See Figure 6.
CAUTION
Do not use any type of power tool (e.g. impact gun or electric drill with nut driver
attached) when tightening the self-tapping bolts to attach the seat bracket.
5. Position the seat assembly over the seat mounting bracket, aligning the holes
provided. See Figure 7.
6. Install the two shoulder bolts (a) and lock nuts (b) removed from the seat mounting
bracket (c) in Step 1. See Figure 7.
Note: Make sure that the bolt’s
shoulder is completely recessed
into the seat bracket when
securing the lock nut.
7. To adjust the position of the seat,
loosen the adjustment knob (d)
on the bottom of the seat. Slide
the seat forward or backward as
desired. Securely retighten the
adjustment knob. Refer to D in
Figure 7.
1
2
(a)
(b)
(b)
(c)
Figure 3
(c)
(a)
(b)
(a)
(b)
Figure 4
(a)
(a)
Figure 5
(a)
(b)
(b)
Figure 6
(a)
(a)
(b)
(b)
(c)
(a)
(b)
(c)
(d)
Figure 7
8
ASSEMBLY
WARNING
Never operate this tractor without either the mulch plug or deck chute installed.
Installing the Deck Chute
1. Remove the wing knobs (a)
installed on the mowing deck
and retain for later installation.
See Figure 8.
2. Install the deck chute (b) into the
discharge opening on the deck. The
rear of the chute should be under
the tab (f) on the rear deck bracket
(g). The studs (c) on the deck
surface will fit through the holes
on the upper portion of the deck
chute. The small tab (d) on the deck
lip area will fit through the square
cutout on the lower portion of the
deck chute. See Figure 8.
Important: Make certain that the upper-rear portion of deck chute (b) is depressing
the safety switch (e) located on the deck surface and under the tab (f) on the rear deck
bracket (g). The blade(s) will not start without the deck chute (b) properly in place.
3. Secure the deck chute (b) by tightening the wing knobs (a) removed in step 1.
Installing the Mulch Plug (If equipped)
1. Remove the wing knobs (a) installed on the mowing deck and retain for later
installation. See Figure 9.
2. Install the mulch plug (b) into the
discharge opening on the deck. The
rear of the mulch plug (b) should be
under the tab (f) on the rear deck
bracket (g). The studs (c) on the deck
surface will fit through the holes on
the upper portion of the mulch plug
(b). The small tab (d) on the deck
lip area will fit through the square
cutout on the lower portion of the
mulch plug (b). See Figure 9.
Important: Make certain that the
upper-rear portion of mulch plug (b)
is depressing the safety switch (e)
located on the deck surface and under the tab (f) on the rear deck bracket (g). The
blade(s) will not start without the mulch plug (b) properly in place.
3. Secure the mulch plug (b) by tightening the wing knobs (a) removed in step 1.
Installing the Bumper (If equipped)
1. Remove the two screws (a) from the front
and center of the front axle. See Figure 10.
2. Position the bumper (b) over the mounting
holes and secure using the screws (a)
removed in Step 1. See Figure 10.
Checking Tire Pressure
See the tire sidewall for the proper inflation
pressure. Proper inflation pressure should be
maintained at all times.
Note: The tires on your tractor may be over-inflated for shipping purposes. If necessary,
reduce the tire pressure before operating the tractor.
(a)
(a)
(b)
(c)
(c)
(d)
(e)
(f)
(g)
Figure 8
(a) (a)
(b)
(c)
(c)
(d)
(e)
(f)
(g)
Figure 9
(a)
(a)
(b)
Figure 10
Charging the Battery
WARNING
• California Proposition 65: Cancer and reproductive harm –
www.P65Warnings.ca.gov.
• The battery contains corrosive fluid and toxic material — HANDLE WITH
CARE. Keep away from children. Do not puncture, disassemble, mutilate, or
incinerate. Explosive gases could be vented during charging or discharging.
Charge in a well ventilated area, away from sources of ignition.
• Recharge only with the charger provided with this tractor. A charger that is not
suitable for this machine may damage the batteries or create the risk of fire.
• Do not charge or operate the tractor in the rain or in wet conditions.
Refer to the manual packed with your battery charger for further information and
instructions on charging the battery. The charging port is located on the rear body panel of
the tractor.
To charge the battery:
1. Lift the charge port cover (a). See Figure 11.
2. Insert the charging cord (b) into the charging port (c).
3. Plug charger power cord (b) into wall
receptacle (outlet). See Figure 11.
Note: It will take approximately 4 hours
to fully charge the battery.
Note: The Vehicle Control Module (VCM)
LED’s will blink continuously when
charging and the LCD display will display
percentage of charge. The battery is
completely charged when all green lights
are illuminated and the LCD displays 100%.
Note: When the charging cord is plugged
into the tractor and not yet plugged into
the wall, the LED’s will illuminate continuously until the cord is plugged into the wall.
If at any time your charger displays a fault while charging your battery, follow these
procedures:
1. Turn the key off.
2. Unplug the charging cord from the tractor.
3. Unplug the charger power cord from the power source.
4. Plug the charger power cord back into the power source.
5. Plug the charging cord back into the tractor.
6. It the fault persists contact qualified service personnel.
Note: Rechargeable batteries degrade with time and use. The battery may eventually need
to be replaced. To have the battery replaced, contact your authorized Service Dealer.
Note: Using old or faulty battery could cause a system fault that results in loss of power.
Battery Charging Tips
• The battery should be fully charged before the initial use.
• The battery should be fully charged after each use. Storing the battery in a
discharged state could reduce performance.
• The battery will turn off automatically after a complete charge.
• It will take approximately 4 hours to fully charge the battery. Leaving the battery
connected to the charger for more than 4 hours will not damage the battery.
• The battery does not develop a memory and does not need to be fully discharged
before recharging.
• Always disconnect battery charger (or extension cord, if used) from the electrical
receptacle (outlet) first, then disconnect the charging cord from the charging port.
• Never charge a frozen battery.
• It is recommended that the tractor be charged once every month during off-season
storage.
(c)
(a)
(b)
Figure 11
9
OPERATION
WARNING
Use extreme caution while operating the tractor in the REVERSE CAUTION
MODE. Always look down and behind before and while backing. Do not
operate the tractor when children or others are around. Stop the tractor
immediately if someone enters the area.
Headlight Button
Located on the VCM, the headlight button is used to turn the headlights on or
off.
Cruise Control Button
Located on the VCM, pressing the cruise control button while the tractor is in
motion allows the tractor to remain at a constant ground speed without applying
pressure to the forward drive pedal, the LCD Screen displays “CRUISE ON” when
the cruise control is activated. The cruise control can be disengaged by pressing
either the cruise control button, the brake pedal or the forward drive pedal.
Note: Cruise control will not engage at the tractor’s fastest ground speed. If the operator
should attempt to do so, the tractor will automatically decelerate to the fastest optimal
mowing ground speed.
Note: Cruise control will not engage in reverse.
LCD Screen & Battery Level Indicator
Located on the VCM, the LCD display & battery level indicator are used to provide
instructions, warnings and information about your tractor systems and the battery level of
your tractor.
Key Switch (B)
Style B1 (If Equipped)
Style B2 (If Equipped)
The key switch is located on the left fender and powers the VCM when the key is in the ON
(I) position. The tractor cannot be started unless the key is in the ON (I) position and the
START/STOP button is depressed. Turning the key to the OFF (O) position turns the tractor
off.
Do No
t
Remove Labe
l
While On Displa
y
I 25799
Ne pa
s
Supprimer l'étiquette
Pendant l'affichag
e
S
u
p
p
r
i
m
e
r
l
'
é
t
i
q
u
e
t
t
e
p
o
u
r
d
é
m
a
r
r
e
r
R
e
m
o
v
e
L
a
b
e
l
T
o
S
t
a
r
t
Note: Before your tractor can be started, the safety label covering the key
switch must be removed. This label is in place to prevent unintended starting
when the tractor is on display. Peel off the label to access the key switch.
Forward Drive Pedal (C)
The forward drive pedal is located on the right side of the steering column, along the
running board. Press the forward drive pedal forward to allow the tractor to travel forward.
Ground speed is also controlled with the forward drive pedal. The further forward the pedal
is depressed, the faster the tractor will travel. The pedal will return to its original/neutral
position when it is not pressed.
Reverse Drive Pedal (D)
The reverse drive pedal is located on the right side of the steering column along the
running board. Ground speed is also controlled with the reverse drive pedal. The further
rearward the pedal is pressed, the faster the tractor will travel. The pedal will return to its
original/neutral position when it is released.
Brake Pedal (E)
The brake pedal is located on the left side of the steering column, along the running board.
The brake pedal can be used for stopping the tractor or setting the parking brake.
Note: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the tractor
when facing forward while seated in the operator’s seat.
Vehicle Control Module (VCM) (A)
WARNING
Never leave a running machine unattended. Always disengage PTO, set parking
brake, stop tractor and remove the key to prevent unintended starting.
The vehicle control module (VCM) is located on the left
fender of the tractor.
The VCM is the location of several control buttons for
your tractor. The VCM inludes the START/STOP button,
PTO (blades ON/OFF) button , Reverse Caution Mode
(RCM) button, Headlight button, Cruise Control button,
LCD Screen and the Battery Level Indicator.
CAUTION
Prior to operating the tractor, refer to both Safety Interlock Switches and
Starting The Tractor in the Operation section of this manual for detailed
instructions regarding the VCM and operating the tractor in REVERSE
CAUTION MODE.
Start/Stop Button
Located on the VCM, the start/stop button is used to start and stop the tractor.
PTO (Blades ON/OFF) Button
Located on the VCM, the PTO button is used to operate the blades. To engage the
cutting deck (blades ON), press and hold the PTO button for one second. The green
indicator light below the PTO button is ON and the LCD Screen displays “CUT DECK
ON” for two (2) seconds then returns to the hour meter. Pressing the PTO button again will
disengage the cutting deck (Blades OFF). The green indicator light below the PTO button is
OFF.
Reverse Caution Mode (RCM) Button
Located on the VCM, the RCM button allows the tractor to be operated in reverse
with the blade(s) engaged (ON). To activate the RCM, press and hold the RCM
button down for three seconds. When activated, the red indicator light is
illuminated. To de-activate the RCM, press the RCM button again. When the RCM is not
activated, the red indicator light is not illuminated. Refer to the Operation section of this
manual for more information on operating the tractor in the reverse caution mode.
Note: Mowing in reverse is not recommended.
RC
M
PT
O
RF
3
sec.
1
sec.
F
C
F
D
E
H
G
BA
K
I
J
Figure 12
10
OPERATION
Note: The brake pedal must be fully depressed to start the tractor. Refer to Safety Interlock
Switches for more information.
Park Brake Lever (F)
The Park Brake Lever is located on the right side of the steering column and is used to
engage the parking brake. Refer to Engaging the Parking Brake section of this manual for
detailed instructions regarding setting the parking brake. Refer to Releasing the Parking
brake section of this manual for instructions regarding releasing the parking brake.
Deck Lift Lever (G)
Located on your tractor’s right fender, the deck lift lever is used to change the height
of the cutting deck (5 positions). To use the deck lift lever, move the lever to the left,
then place in the notch best suited for your application. The lowest position is “1”
and the highest position is “5”.
Position “1” is approximately a 1” cutting height, Position “5” is approximately a
4” cutting height and the change in height is approximately 3/4” between each
position.
Headlight (H)
The headlights will turn ON whenever the key is ON and the headlight button is pressed. To
turn the headlights OFF, press the headlight button again.
Charging Port (I)
The charging port is located on the rear of the tractor. To access the charging port, lift up
on the charging port cover.
USB Charging Ports (J) (If Equipped)
If equipped, a pair of USB power sources are located on the left console. The two
USB ports are both rated 2.1 A. The ports can be used to charge your phone or
power up other USB devices.
WARNING
Do not have any devices plugged into your USB charging ports when starting
the tractor. Doing so may cause damage to your device.
Cup Holder (K)
The cup holder is located to the left of the operator’s seat.
Operation
Safety Interlock System
This tractor is equipped with a safety interlock system for the protection of the operator.
If the interlock system should ever malfunction, do not operate the tractor. Contact an
authorized service dealer.
•
• The safety interlock system prevents the operator from turning the tractor ON
unless the operator is in the seat with the parking brake engaged or brake pedal
fully depressed and the drive pedal in the NEUTRAL position.
• The tractor will not operate with the charger cord plugged into the charging port
and/or the charging port cover open or removed.
• The tractor will automatically shut off the blade(s) and drive motors if the operator
leaves the seat.
Note: To restart the tractor, follow the proper starting procedures as instructed in
Starting the Tractor section on this page.
WARNING
Do not operate the tractor if the safety interlock system is malfunctioning.
This system was designed for your safety and protection.
Engaging the Parking Brake
1. Fully depress the brake pedal and hold it down with your foot.
2. Move the parking brake lever back into the parking brake position.
3. Release the brake pedal to allow the parking brake to engage.
Releasing the Parking Brake
1. Depress the brake pedal.
2. Move the parking brake lever forward out of the parking brake position.
3. Release the brake pedal.
Setting the Cutting Height
Select the height position of the cutting deck by placing the deck lift lever in any of the five
(5) different cutting height notches on the right side of the fender.
WARNING
Keep hands and feet away from the discharge opening of the cutting deck.
Refer to Leveling the Deck in the Service & Maintenance section of this manual for more
detailed instructions regarding deck adjustment.
Starting the Tractor
1. Unplug the charging cord (if necessary). If
the cord is still plugged in, a reminder will
display on the VCM when the key switch is
turned on.
2. Sit in the operator’s seat. Insert the key into the key switch
Note: A reminder will display on the VCM if
the operator is not in the seat when the key
switch is turned on.
3. Fully depress the brake pedal or set the parking brake.
Note: If the brake is not engaged a reminder
will display on the VCM when the key switch
is turned on.
4. Turn the key clockwise to the ON (I) position.
5. Press the start/stop button down until you hear two beeps.
Note: The VCM and drive motors are now activated and the tractor is ready to be
operated.
Stopping the Tractor
WARNING
If you strike a foreign object, stop the tractor, turn the key to OFF and remove.
Thoroughly inspect the machine for any damage. Repair the damage before
restarting and operating.
1. If the blade is engaged (blades ON), press the PTO button to disengage the blades
(blades OFF) and engage the parking brake.
2. Press the start/stop button (you will hear one beep) or turn the key counter-
clockwise to the OFF (O) position.
3. Remove the key to prevent unauthorized use by children or others.
Driving the Tractor
WARNING
• Avoid sudden starts, excessive speed and sudden stops.
• Do not leave the seat of the tractor without first pressing the PTO
button to turn off the blade(s), and engaging the parking brake. If
leaving the tractor unattended, turn the key to the OFF position and
remove.
• Always look down and behind before and while backing up to avoid a
back-over accident.
1. Disengage the parking brake
11
OPERATION
2. To travel FORWARD, slowly depress the forward drive pedal until the desired speed
is reached.
3. To travel in REVERSE, slowly depress the reverse drive pedal until the desired speed
is reached.
4. The tractor is brought to a stop by releasing the forward or reverse drive pedal and
depressing the brake pedal.
WARNING
Before leaving the operator’s position for any reason, disengage the blade(s),
engage the parking brake, turn the key switch to OFF position and remove the
key.
Reverse Caution Mode (RCM)
The REVERSE CAUTION MODE button allows the tractor to be operated in reverse with the
blade(s) (PTO) engaged.
Note: Mowing in reverse is not recommended.
WARNING
Use extreme caution while operating the tractor in the REVERSE CAUTION
MODE. Always look down and behind before and while backing. Do not
operate the tractor when children or others are around. Stop the tractor
immediately if someone enters the area.
To use the REVERSE CAUTION MODE:
Note: The operator MUST be seated in the seat.
1. Start the tractor as previously instructed.
2. Press and hold the RCM button down for three seconds until the red indicator light
illuminates. The red indicator will remain on as long as the REVERSE CAUTION MODE
is on.
3. Once activated (indicator light ON), the tractor can be driven in reverse with the
cutting blade(s) (PTO) engaged.
4. Always look down and behind before and while backing to make sure no children or
others are around. After resuming forward motion, press the RCM button to return
to normal mowing operation.
The REVERSE CAUTION MODE will remain activate until:
a. The RCM button is pressed again to turn off the mode (red indicator light
turns off).
b. The operator leaves the seat.
c. The START/STOP button is pressed.
Operating the PTO
To operate the PTO (Blades ON/OFF) proceed as follows:
Press the PTO button for one second. When activated the green indicator light under the
PTO button is ON (Blades ON). Press the PTO button again for one second, green indicator
light is OFF (Blades OFF).
Mulching (If equipped)
Mulching is a process of recirculating grass clippings repeatedly beneath the cutting deck.
The ultra-fine clippings are then forced back into the lawn where they act as a natural
fertilizer. Refer to the Assembly section of this manual for instructions on how to install the
mulch kit (if equipped).
Mowing
WARNING
• To help avoid blade contact or a thrown object injury, keep bystanders,
helpers, children and pets at least 75 feet (23 meters) from the tractor
while it is in operation. Stop tractor if anyone enters the area.
• Plan your mowing pattern to avoid discharge of materials toward roads,
sidewalks, bystanders and the like. Also, avoid discharging material
against a wall or obstruction which may cause discharged material to
ricochet back toward the operator.
The following information will be helpful when using the cutting deck with your tractor:
1. Do not mow or drive at high ground speed, especially if a mulch kit or grass collector
is installed.
2. For best results it is recommended that the first two laps be cut clockwise with the
discharge facing towards the center of your lawn. After the first two laps, reverse
the direction to discharge to the outside for the balance of cutting. This will give a
better appearance to the lawn.
3. Do not cut the grass too short. Short grass invites weed growth and yellows quickly
in dry weather.
4. Under heavier conditions it may be necessary to go back over the cut area a second
time to get a clean cut.
5. Do NOT attempt to mow heavy brush and weeds and grass taller than 10” (25.4 cm).
Your tractor is designed to mow lawns, NOT clear brush.
Routine Service Reminders
During operation, a pair of service reminders will appear at regular intervals to help you
properly maintain your tractor:
Sharpen Blade Reminder: Occurs
every 10 hours of PTO run time. When this
message is displayed, the blade should
be checked and sharpened or replaced if
worn. For instructions, see Sharpening or
Replacing the blades in the Service and
Maintenance section of this manual.
Check Tire Pressure Reminder:
Occurs every 5 hours. When this message
is displayed check and adjust the tire
pressure per the proper tire pressure listed
on the tire sidewall. See Checking Tire
Pressure in the Assembly section of this
manual.
12
SERVICE AND MAINTENANCE
IMPORTANT: Bring the battery charger when arriving at your authorized service
dealer for any scheduled service.
DANGER
• The electrical components on this tractor are not serviceable. Please
contact an authorized service dealer for any service needs.
• Have your tractor serviced by qualified service personnel using only
identical replacement parts. This will ensure that the safety of the
tractor is maintained.
Post-Operation Tractor Care
After each operation of the tractor, the following procedures should be
implemented to extend the life of your tractor and ensure safe operating conditions.
DANGER
Failure to follow these recommendations may result in serious injury
to yourself or others and may cause damage to the tractor.
WARNING
Before inspecting, cleaning or servicing the tractor, power off the
tractor and remove the key.
Follow the maintenance schedule given below. This chart describes service
guidelines only. Use the Service Log column to keep track of completed
maintenance tasks. Contact an authorized service dealer to schedule a
service.
Prior to
Use
After First
Five Hours
Every Five
Hours
Every
10 Hours
Every
25 Hours
Every
50 Hours
Every 100
Hours
Prior to
Storing
Clean Top and Underside of Deck
P P
Check/Clean Around fuses, Wiring and Wiring Harnesses
P P
Check/Clean Around Transmission and Axle
P P
Clean Tractor
P
Lube Front Axles and Rims
P P
Lube Pedal Pivot Points, Parking Brake and Lift Linkage
P P
Check Tire Pressure/Inate to Sidewall Specication
P P
Check Deck Level/Pitch/Adjust as needed
P P
Check Blade(s)/Sharpen or Replace as Needed
P P P
Charge Battery
P P
Check Safety Interlock System
P
Check Mower Blade Stop Time
P
Check Blade Mount Bolt Torque
(Tighten to 450-600 in-lbs(51.9–67.8 N-m))
P P P
Check That All Hardware is in Place and Secure
P P
Cleaning the Underside of the Deck
WARNING
To prevent serious injury, do not use water to clean the tractor, battery
or battery charger. Do not use strong detergents. Household cleaners
that contain aromatic oils such as pine and lemon, and solvents such as
kerosene, can damage plastic.
The underside of tractor deck should be cleaned after each use as grass clippings,
leaves, dirt and other debris will accumulate. This accumulation of grass clippings,
etc., is undesirable as it will promote rust and corrosion.
1. Remove any buildup of grass and leaves on or around the deck motor and
underside of the tractor (DO NOT USE WATER). Wipe the tractor clean with a
dry cloth.
Important: Do not use a pressure washer or garden hose to clean your tractor.
These may cause damage to electric components or the electric motor. The use of
water will result in shortened life and reduce serviceability.
13
SERVICE AND MAINTENANCE
Cleaning the Tractor
WARNING
If the tractor has been recently run, metal surfaces will be hot and can
cause burns to the skin. Let the tractor cool for at least five minutes.
Exercise caution to avoid burns.
Your tractor should be cleaned after each use and under certain conditions, i.e. dry
conditions and/or mulching situations, additional cleaning may be necessary.
One of the best ways to keep your tractor running efficiently and to reduce fire risk
is to regularly remove debris buildup from the tractor. Follow the recommendations
below and contact your authorized dealer with any questions.
• Allow the machine to cool in an open area before cleaning.
• Do not use water on any part
of the tractor. Doing so can
cause damage to the tractor’s
electrical components and
motor. The use of compressed
air and/or leaf blower or a brush,
damp sponge or rag will help
keep the tractor clean.
• Clean around fuses and wiring
harnesses.
• Clean the top of the tractor
deck. See Figure 13.
• Clean around and near the
transmission and axle. See
Figure 14.
• Debris can accumulate
anywhere on the tractor,
especially on horizontal
surfaces. Additional cleaning
may be necessary when
mowing in dry conditions or
when mulching.
• Excess lubrication can
become collection sites for debris. Immediate repair and cleaning up excess
lubrication can help reduce fire hazards.
• In addition to cleaning the tractor before operating and storing, do not
attempt to mow unusually tall grass (10” or higher), dry grass (e.g., pasture)
or piles of dry leaves. Dry grass or leaves may build up on the tractor deck
presenting a potential fire hazard.
Lubrication
DANGER
Bearing failures and overheating can result in fire. Always follow
the instructions in this manual regarding lubrication locations and
intervals. Contact your authorized dealer with any questions about the
lubrication locations and intervals or any unusual noises coming from
any areas a bearing may be located.
WARNING
Before lubricating, repairing, or inspecting, always disengage the PTO,
set the parking brake,turn key to OFF position and remove to prevent
unintended starting.
Figure 13
Rear Wheel Not
Shown for Clarity
Figure 14
Front Axles:
Each end of the tractor’s front pivot bar may be equipped with a grease fitting.
Lubricate with No. 2 multi-purpose grease applied with a grease gun after every 25
hours of operation.
Rear Wheels:
The rear wheels should be removed from the axles once a season. Lubricate the
axles and the rims well with an all-purpose grease before re-installing them.
Pivot Points & Linkage:
Lubricate all the pivot points on the drive system, parking brake and lift linkage at
least once a season with light oil.
Note: It is not necessary to grease the steering pinion/sector gear interface. Doing
so will allow dirt to accumulate and can affect steering performance.
Adjustments
WARNING
Before making adjustments, always disengage the PTO, set the
parking brake, turn key to OFF position and remove to prevent
unintended starting. Protect your hands by using heavy gloves when
handling the blades.
Note: Check the tractor’s tire pressure before performing any deck leveling adjustments.
Refer to Checking Tire Pressure in the Assembly section for information regarding tire
pressure.
Adjusting the Deck
Leveling the Deck (Front-To-Rear)
It is possible to adjust the pitch of the cutting deck. The front of the deck should be
between 0” (level) and 1/4” (6.4 mm) lower than the rear of the deck. Adjust if necessary
as follows:
1. With the tractor parked on a firm, level surface, place the deck lift lever in
the middle position and rotate the blade so that it is aligned with the front
and rear of the tractor.
2. Measure the distance from the front of the blade tip to the ground and the rear
of the blade tip to the ground. The end of the blade facing the front of the deck
should be between 0” (level) and 1/4” (6.4 mm) less than the end of the blade
facing the back of the deck. Determine the approximate distance necessary for
proper adjustment and proceed,
if necessary, to the next step.
3. Locate the flange lock nut (a) on
the front end of the PTO lift rod
(b). See Figure 15.
a. Tighten the flange lock
nut (a) to raise the front
of the deck.
b. Loosen the flange lock
nut (a) to lower the
front of the deck.
Parking Brake Adjustment
If the tractor does not come to a complete stop when the brake pedal is completely
depressed, or if the tractor’s rear wheels can roll with the parking brake applied, the
brake is in need of adjustment. See your authorized service dealer to have the brake
adjusted.
Neutral Adjustment
If the tractor creeps forward or rearward when neither the forward nor reverse
pedal is depressed, contact your local authorized dealer to have the neutral setting
properly adjusted.
Seat Adjustment
Refer to the Assembly section of this manual for seat adjustment instructions.
(a)
(b)
Figure 15
14
SERVICE AND MAINTENANCE
Service
Deck Removal
To remove the cutting deck, proceed as follows:
1. Power off the tractor,
remove the key from the
key switch, and engage the
parking brake.
2. Lower the deck by moving
the deck lift lever into the
lowest (#1) position on the
right fender.
3. Remove the bow-tie cotter
pin (a) and flat washer
(b) from the deck lift
assembly, and retain for
reinstallation later. See
Figure 16.
4. Disconnect the deck motor(s) from the adapters on the underside of the
tractor. Rotate the collar on the larger connector (a) counterclockwise and
carefully pull apart. Repeat the procedure with the smaller connector (b).
Note: Your mower may have one of two different deck motor connector
setups. If your mower has horizontally positioned connectors, see Figure 17.
If your mower has vertically positioned connectors, see Figure 18.
Note: Always disconnect the larger connector first.
5. Remove the remaining bow-tie cotter pins (a)
securing the deck to the tractor, as shown in Figure 19.
(a)
(a)
Figure 19
(a)
(b)
Figure 16
(a)
(b)
Figure 17
(a)
(b)
Figure 18
6. Unplug the wire connector (a) from the safety switch (b) at the rear of the
chute opening. See Figure 20.
(a)
(b)
Figure 20
7. Move the deck lift lever into the highest (#5) position on the right fender to
raise the deck lift arms up and out of the way.
8. Gently slide the cutting deck (from the left side) out from underneath the tractor.
Cutting Deck Installation
1. Raise the deck lift lever into the highest (#5) position on the right fender to
move the deck lift arms out of the way.
2. Gently slide the cutting deck (from the left side) back under the tractor.
3. Plug the wire connector (a) into the safety switch (b) at the rear of the chute
opening. See Figure 20.
Note: Be sure to securely reconnect the wire connector to the safety switch
in Figure 20, you tractor will not start or operate without the safety switch
properly connected.
4. Lower the deck lift lever to the lowest (#1) position.
5. Secure the deck to the deck lift arms using two bow-tie cotter pins. See Figure 19.
Note: The bow-tie cotter pins (a) should be installed from the top down.
6. Reconnect the deck motors on the underside of the tractor. Always connect
the larger connector first and then the smaller connector. See Figure 17.
Note: When reconnecting the deck motors, you must be sure that the
connections are secure.
Blade
WARNING
• Power off the tractor and remove the key before removing the
cutting blade(s) for sharpening or replacement. Protect your
hands by using heavy gloves when grasping the blade.
• Periodically inspect the blade and/or deck motor casting for
cracks or damage, especially after you’ve struck a foreign object.
Do not operate the tractor until damaged components are
replaced.
CAUTION
If the cutting edge of the blade has previously been sharpened, or if
any metal separation is present, replace the blade with a new one.
15
SERVICE AND MAINTENANCE
Sharpening or Replacing the Blade
Note: It may be easier to change the blade by first removing the deck from
beneath the tractor, (refer to Cutting Deck Removal earlier in this section)
then gently flip the deck over to expose its underside. It is possible to change
the blade, however, with the deck still attached to the tractor. If attempting
to change the blade with the deck still installed on the tractor, first move the
deck lift lever to its highest (#5) position.
1. Remove the mulch
plug, deck chute or
bagging chute, if
equipped, exposing
the deck chute
opening.
2. Using a block of wood
or 2 x 4, insert it into
the deck opening
and rotate the blade
around until it wedges
the wood between
the deck opening and
the cutting blade, as
shown in Figure 21.
3. Remove the hex screw
(a) and the blade bell
support (b) which
holds the blade (c) and
the blade adapter (d)
to the deck motor. See
Figure 22.
4. Remove blade (c) and
adapter (d) from the
deck motor spindle
See Figure 22.
5. To properly sharpen
the cutting blade,
remove equal amounts
of metal from both ends
of the blade along the
cutting edges, parallel
to the trailing edge,
at a 25°- to 30° angle.
Always grind each
cutting blade edge
equally to maintain
proper blade balance.
See Figure 23.
6. Test the blade’s balance
using a blade balancer.
Grind metal from the
heavy side until it
balances evenly.
WARNING
A poorly balanced blade will cause excessive vibration, may damage
the tractor and/or result in personal injury.
Note: When replacing the blade, be sure to install the blade with the side of
the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the
ground when the tractor is in the operating position.
7. Reinstall blade when properly sharpened. Torque to 450-600 in-lbs
(50.9–67.8 N-m).
Figure 21
(d)
(c)
(a)
(b)
Figure 22
Figure 23
Off-Season Storage
Storing the Tractor
• Allow the machine to cool in an open area before storing.
• Do not park the tractor near any flammable materials (wood, cloth or
chemicals) or any open flames or other potential source of ignition (furnace,
water heater or any other type of heater).
• Remove all combustible materials from the tractor before storing. Empty
cargo boxes, grass catchers or containers.
Removing The Tractor From Storage
1. Fully charge the battery and inflate the tires to the recommended pressures.
2. Drive the tractor without a load to make certain all the tractor systems are
functioning properly.
Battery Storage
1. The battery should be stored with a full charge. A discharged battery can
freeze faster than a charged battery in cold temperatures.
2. The battery charger should remain connected to the charging port on the
tractor when not in use.
3. If keeping the charger connected during off-season storage is not possible,
the battery should be fully charged once every month.
Note: It will take approximately 4 hours to fully charge the battery. Leaving the
battery connected to the charger for more than 4 hours will not damage the battery.
4. Battery should not be kept in a discharged state. Permanent damage to the
battery can occur.
5. Fully recharge the battery before returning to service.
Battery Disposal
Disposing of Damaged or Worn-Out Battery
WARNING
• The following toxic and corrosive material is used in this battery:
LITHIUM-ION, a toxic material.
• Do not use broken or cracked batteries, even if there is no leakage.
Replace damaged or worn-out batteries with new batteries. DO
NOT ATTEMPT TO REPAIR BATTERIES! Repair attempts may result in
severe personal injury, due to explosion or electrical shock.
To avoid personal injury and damage to the environment:
• Do not attempt to remove or destroy any of the battery components. Do not
open or mutilate the battery. If a leak develops, released electrolytes are
corrosive and toxic. Do not get the solution in your eyes or on your skin, and
do not swallow it.
• Do not dispose of the battery in the regular household trash.
• Do not dispose of the battery in a fire. The cell may explode.
• Do not dispose of the battery where it will become part of any waste landfill
or municipal solid waste stream.
• Contact your local authorized service dealer for proper battery recycling.
16
SERVICE AND MAINTENANCE
Troubleshooting
Problem Cause Remedy
Excessive Vibration 1. Blade loose or unbalanced
2. Cutting blade damaged, unbalanced or bent.
1. Tighten cutting blade and deck spindle
2. Replace the blade
Uneven Cut 1. Deck not properly leveled
2. Cutting blade dull or damaged
3. Uneven tire pressure
1. Perform front-to-rear deck adjustment
2. Sharpen or replace cutting blade
3. Check and correct tire pressure in all four tires
Tractor will not mulch grass 1. Wet grass
2. Excessively high grass
3. Dull blade
1. Do not mulch when grass is wet
2. Mow once at a high cutting height, then mow again at
desired height or make a narrower cutting swath
3. Sharpen or replace blade
Tractor stopped or will not start 1. Electrical system fault 1. Shut off and restart tractor. If problem persists, contact an
authorized service dealer
The blades do not rotate /blades stopped 1. Overload
2. Low battery
1. Allow deck motor(s) to cool/raise deck height
2. Return home, plug into charger
The blade(s) stopped when traveling in
reverse
1. Blade(s) stopped 1. Restart blade(s) (PTO). Make sure Reverse Caution Mode is
activated.
Reduced Speed 1. Low battery
2. Overload
1. Charge battery as instructed in the battery charger manual
2. Raise deck
LCD Screen Messages
Message Description
Brake Switch Fault: The deck and
drive shut off. Power off and restart
tractor. If problem persists contact
qualified service personnel.
Accelerator Pedal Sensor Fault:
The deck and drive shut off. Power off
and restart tractor. If problem persists
contact qualified service personnel.
Seat Switch Fault: The deck and
drive shut off. Power off tractor,
sit in seat and restart tractor. If
problem persists contact qualified
service personnel.
Cutting Deck Overload: The
deck and drive shut off. Power off
the tractor, clean under the deck
as instructed in the Post-Operation
Tractor Care section and restart the
tractor. Raise the deck and/or cut at
a slower pace. If problem persists
contact qualified service personnel.
Drive Motor Over Current Fault:
The deck and drive shut off. Power
off, let the tractor cool and restart
tractor. If problem persists contact
qualified service personnel.
Drive Motor Control Fault: The
deck and drive shut off. Power off and
restart tractor. If problem persists
contact qualified service personnel.
Message Description
Self Test Fault: The deck and
drive shut off. Power off and restart
tractor. If problem persists contact
qualified service personnel.
Electrical Faults: The deck and
drive shut off. Power off and restart
tractor. If problem persists contact
qualified service personnel.
Battery Temperature Low:
Move the tractor to a warm
location and allow the battery to
warm. If problem persists contact
qualified service personnel.
High Temperature Faults:
Power off, let the tractor cool
and restart tractor. If problem
persists contact qualified service
personnel.
Charge Port Door is Open: The
tractor will come to a stop and shut
off. Close the charge port door and
restart tractor. If problem persists
contact qualified service personnel.
Low Battery Warning: The
battery is low and should be
charged as soon as possible.
Manual del OperadOr
Tractor a Batería de Ion de Litio
ADVERTENCIA
Lea y cumpla todas las normas de seguridad y las instrucciones de este manual antes de intentar operar esta máquina.
Si no sigue estas instrucciones, se pueden provocar lesiones personales.
ADVERTENCIA
Proposición 65 de California
Cáncer y Daños Reproductivos – www.P65Warnings.ca.gov.
NOTA: Este Manual del Operador corresponde a varios modelos. Las características pueden variar según los modelos. No todas las
características que se incluyen en este manual se aplican a todos los modelos y el modelo que se ilustra aquí puede diferir del suyo.
Formulario Nº 769-20394
(4 de abril de 2019)
Prácticas de Operación Seguras ............................ 2
Montaje .................................................................... 7
Funcionamiento .....................................................10
Servicio y Mantenimiento .....................................13
Solución de Problemas ..........................................17
Piezas/Garantía ..........Consulte el suplemento que
se adjunta por separado
Índice
3 3 2 7
J
Registro de Información del Producto
Antes de configurar y hacer funcionar su equipo nuevo, por
favor localice la placa de modelo que viene en el equipo
y registre la información en el espacio de la derecha. Para
encontrar la placa de modelo, eleve el asiento y mire en
la parte inferior de la bandeja del asiento. Si tiene que
solicitar soporte técnico a través de nuestro sitio web o de
un distribuidor de servicio local autorizado, necesitará esta
información.
NúMero de Modelo
NúMero de Serie
D
2
PRÁCTICAS DE OPERACIÓN SEGURAS
Información General
1. Lea, entienda y cumpla todas las instrucciones incluidas en el tractor y en los
manuales antes de intentar armar la unidad y utilizarla. Guarde este manual
en un lugar seguro para consultas futuras y periódicas, así como para solicitar
repuestos.
2. Familiarícese con todos los controles y su correcto funcionamiento. Sepa cómo
detener el tractor y desactivar los controles rápidamente.
3. No permita nunca que los niños menores de 14 años utilicen este tractor. Los
niños de 14 años en adelante deben leer y entender las instrucciones y las
prácticas de operación seguras contenidas en este manual y sobre el tractor,
y deben ser entrenados y supervisados por un adulto.
4. Nunca permita que los adultos operen este tractor sin recibir antes la
instrucción apropiada.
5. Si se presentan situaciones que no están previstas en este manual, tenga
cuidado y use el sentido común. Póngase en contacto con su representante
de atención al cliente para obtener ayuda.
6. De conformidad con la Comisión de Seguridad de Productos para el
Consumidor de los Estados Unidos (CPSC) y la Agencia de Protección
Ambiental de los Estados Unidos (EPA), este producto tiene una vida útil
estimada de siete (7) años, en condiciones normales de uso. Al final de su
vida útil, se deberá solicitar una inspección del producto anualmente a fin de
asegurarse de que todos los sistemas mecánicos, eléctricos y de seguridad
funcionen adecuadamente, de manera segura y no estén excesivamente
desgastados. Si no lo hace, puede ocasionar accidentes, lesiones o la muerte.
Preparativos Anteriores al Uso
1. Revise minuciosamente el área donde se va a usar el tractor. Saque todas las piedras,
palos, cables, huesos, juguetes y demás objetos extraños que puedan ser recogidos y
arrojados por la(s) cuchilla(s). Los objetos arrojados por la máquina pueden producir
lesiones personales graves.
2. Para ayudar a evitar el contacto con las cuchillas o una lesión por algún objeto
que sea arrojado, mantenga a personas, ayudantes, niños y mascotas alejados
al menos 75 pies (23 metros) del tractor mientras está en funcionamiento.
Mantenga a las personas, los niños y las mascotas en interiores durante el
funcionamiento. Detenga el tractor si alguien entra en la zona.
3. Esté atento a la dirección de la descarga del tractor y no apunte a nadie.
4. Para protegerse los ojos, utilice siempre anteojos o antiparras de seguridad
durante la operación o mientras realiza ajustes o reparaciones. Los objetos
arrojados que rebotan pueden producir lesiones graves en los ojos.
5. Utilice zapatos de trabajo resistentes, de suela fuerte, y pantalones y
camisas ajustados. Las ropas sueltas, las alhajas y el cabello largo pueden
engancharse en las piezas móviles. Nunca haga funcionar este tractor si está
descalzo o con sandalias.
6. No cargue ni haga funcionar el tractor bajo la lluvia o en condiciones húmedas.
7. Use solo aditamentos o accesorios aprobados para este tractor por el
fabricante del tractor. Lea, comprenda y siga todas las instrucciones incluidas
con el accesorio o aditamento aprobado.
Funcionamiento
1. Los datos estadísticos muestran que los operadores mayores de 65 años se
ven implicados en un alto porcentaje de lesiones relacionadas con tractores.
Estos operadores deben evaluar su capacidad para operar el tractor en forma
suficientemente segura para protegerse a ellos mismos y a los demás contra
lesiones graves.
2. Aplique el freno de mano antes de intentar encender el tractor.
3. Planifique el patrón de corte, para evitar que la descarga de materiales se
dirija hacia caminos, aceras, observadores, etc. Evite además descargar
material contra una pared u obstrucción, ya que esto podría hacer rebotar el
material descargado contra el operador.
4. En caso de falla en un sistema o pérdida completa de energía de la batería, el
tractor podría deslizarse por la cuesta sin control. Presione el pedal de freno
para mantener el control y detener el tractor. Vuelva a encender el motor. Si la
falla del sistema persiste, póngase en contacto con su distribuidor de servicio
autorizado.
5. No ponga las manos ni los pies cerca de las piezas rotatorias ni debajo de la
plataforma de corte. El contacto con la(s) cuchilla(s) puede amputar manos
y pies.
6. Esté atento a los hoyos, surcos, baches, rocas, u otros objetos ocultos. El
terreno desnivelado puede hacer que vuelque el tractor. El césped alto puede
ocultar obstáculos.
7. Revise la holgura superior antes de conducir debajo de ramas bajas de
árboles, cables, cerramientos de puertas, etc., donde el operador puede
golpearse o ser tirado del tractor, lo que podría resultar en lesiones graves.
8. Nunca deje un tractor en funcionamiento sin vigilancia. Siempre apague las
cuchillas, aplique el freno de mano, presione el botón Encendido/Detención,
coloque la llave en posición OFF y retire la llave antes de bajar del tractor.
9. Apague las cuchillas, coloque el freno de mano, presione el botón de
Encendido/Detención y espere hasta que la(s) cuchilla(s) se detenga(n)
por completo antes de retirar el colector de recortes de césped, vaciar los
recortes, desbloquear la tolva, retirar cualquier residuo o desecho, o realizar
cualquier ajuste.
10. Su tractor fue diseñado para cortar césped residencial normal, con una altura
no mayor de 10” (25.4 cm). No intente cortar césped demasiado crecido, seco
(como un pastizal) ni pilas de hojas secas. El césped o las hojas que están
secos pueden entrar en contacto con superficies calientes y/o acumularse en
la plataforma del tractor presentando un potencial peligro de incendio.
11. Apague las cuchillas antes de desplazarse marcha atrás. Retroceda
lentamente. Siempre mire hacia abajo y hacia atrás antes y mientras
retrocede para evitar accidentes.
12. Nunca lleve pasajeros.
13. Manténgase a por lo menos 10 pies (3 metros) de barrancos, zanjas o
terraplenes o del borde del agua. El tractor puede volcarse repentinamente
si una de las ruedas pasa el borde de un acantilado o zanja o si se desmorona
un borde.
ADVERTENCIA
Este símbolo indica instrucciones de seguridad importantes que, de no seguirse, pueden poner en peligro su seguridad personal y/o material y la de otras
personas. Lea y cumpla todas las instrucciones de este manual antes de intentar hacer funcionar este tractor. Si no sigue estas instrucciones, se pueden
provocar lesiones personales. Cuando vea este símbolo, ¡TENGA EN CUENTA LA ADVERTENCIA!
PELIGRO
Este tractor fue diseñado para ser utilizado respetando las prácticas de operación seguras que figuran en este manual. Al igual que con cualquier tipo de
equipo motorizado, un descuido o error por parte del operador puede producir lesiones graves. Este tractor es capaz de amputar dedos, manos y pies y de
arrojar residuos. De no respetar las instrucciones de seguridad siguientes, se pueden ocasionar lesiones graves o la muerte.
Sistema de la Batería de Ion de Litio
Cualquier tarea de servicio requiere sumo cuidado y conocimiento del sistema y debe ser realizado únicamente por un técnico de servicio calificado. Para reparar su tractor,
diríjase a su distribuidor de servicio autorizado más cercano. Cuando realice el servicio, debe usar siempre piezas de reemplazo del fabricante del equipo original (OEM).
3
PRÁCTICAS DE OPERACIÓN SEGURAS
14. Si falta o está dañado un deflector del canal, una clavija para abono o
colector de césped podría causar lesiones por contacto con la cuchilla u
objetos arrojados.
15. No opere el tractor si no está el deflector del canal, la clavija para abono o el
colector de césped completo en su lugar correspondiente.
16. Tenga mucho cuidado con los colectores de césped y otros accesorios.
Pueden modificar la estabilidad del tractor. Siga siempre las instrucciones
del fabricante del accesorio.
17. Detenga la(s) cuchilla(s) cuando cruce sendas, senderos o caminos de
gravilla, y cuando no esté cortando el césped.
18. Vigile el tránsito vehicular cuando esté operando cerca de caminos o en cruces.
Este tractor no se ha diseñado para el uso en la vía pública.
19. Úsela solamente con luz natural o con buena luz artificial.
20. No haga funcionar el tractor si se encuentra bajo los efectos del alcohol o las
drogas.
21. Reduzca la velocidad antes de girar. Opere el tractor suavemente. Evite que
funcione de manera errática y a excesiva velocidad.
22. Los motores pueden calentarse y provocar quemaduras graves. No los
toque. Deje que se enfríe el tractor durante cinco minutos antes de intentar
cualquier tarea de mantenimiento.
23. No apague el tractor y no se desplace cuesta abajo sin control. Desplazarse cuesta
abajo sin control podría causar daños serios a los motores.
Niños
1. Se pueden producir accidentes trágicos si el operador no está alerta a la
presencia de niños. Por lo general, los niños se sienten atraídos por el tractor
y su actividad. Los niños no son conscientes de los peligros. Nunca asuma que
los niños permanecerán donde los vio por última vez.
2. Mantenga a observadores, niños y mascotas en interiores durante la
operación bajo la atenta supervisión de un adulto responsable que no sea el
operador. Detenga el tractor si alguien entra en la zona.
3. Nunca transporte niños, ni siquiera con las cuchillas desactivadas. Podrían
caerse y resultar gravemente heridos o interferir con la operación segura del
tractor. Los niños que ya hubieran sido transportados en ocasiones anteriores
podrían aparecer repentinamente en la zona de corte para otra vuelta y ser
atropellados o también podrían ser arrollados al dar marcha atrás con el
tractor.
4. Esté alerta y apague el tractor si un niño o un observador ingresa al área.
5. Para evitar accidentes al retroceder, siempre mire hacia atrás y hacia abajo
para ver si hay niños.
6. Tenga mucho cuidado al aproximarse a esquinas ciegas, puertas, arbustos,
árboles u otros objetos que puedan obstaculizarle la vista de un niño que
pudiese correr al encuentro del tractor.
7. No permita nunca que los niños menores de 14 años utilicen este tractor. Los
niños de 14 años en adelante deben leer y entender las instrucciones y las
prácticas de operación seguras contenidas en este manual y sobre el tractor,
y deben ser entrenados y supervisados por un adulto.
8. No permita que se transporte a ningún niño por diversión en el tractor. El
tractor no es un juguete ni un carro de paseo. Adviértales a sus hijos que el
tractor puede ser peligroso y que deben mantenerse alejados de él en todo
momento.
9. Mantenga a los niños alejados de un tractor que está caliente o en
funcionamiento. Podrían sufrir quemaduras por contacto con motores
calientes.
10. Retire la llave cuando el tractor quede sin vigilancia para evitar el
funcionamiento no autorizado. Asegúrese de que la llave quede fuera del
alcance de los niños pequeños.
Operación en Pendientes
1. Las pendientes son un factor importante en los accidentes ocasionados por
pérdida de control y vuelcos que pueden causar lesiones graves e incluso
la muerte. Todas las pendientes requieren precaución extra. Si no puede
retroceder por la pendiente o si no se siente seguro, no realice ningún corte o
no se desplace sobre ella.
2. Para su seguridad, mida las pendientes antes de usar el tractor en el lugar
inclinado. Use un dispositivo de medición de pendientes además del
indicador de pendiente que se incluye como parte de este manual para medir
las pendientes antes de operar este tractor sobre una zona inclinada o con
pendientes. Para medir las pendientes, también se pueden usar aplicaciones
de teléfonos inteligentes. Si la pendiente es de más de 12 grados según
figure en el indicador de pendientes o un dispositivo de medición de
pendientes, no haga funcionar este tractor en ese sector pues podría causar
lesiones graves.
3. No corte el césped en pendientes de más de 12 grados (21%).
4. No corte el césped subiendo y bajando pendientes, solo hágalo de forma
transversal a las pendientes que son de menos de 12 grados (21%). Utilice las
velocidades bajas y evite los giros bruscos.
5. No corte el césped húmedo. La reducción de la tracción puede causar
derrapes o pérdidas del control.
6. No opere el tractor en ninguna condición en la que se comprometan la
tracción, la dirección o la estabilidad. Los neumáticos podrían deslizarse
incluso si las ruedas están detenidas.
7. Evite arrancar y parar en una pendiente. Evite hacer cambios repentinos de
velocidad o dirección. Haga los giros de forma lenta y gradual.
8. Tenga mucho cuidado al operar este tractor con el colector de césped y otros
accesorios. Pueden comprometer la estabilidad del tractor. No utilice el
colector de césped en pendientes superiores a 10 grados (17%).
9. No intente estabilizar el tractor poniendo el pie en el suelo.
10. Haga que todos los movimientos en las pendientes sean lentos y graduales.
No realice cambios bruscos de velocidad o dirección. La aceleración repentina
podría hacer que el frente del tractor se levantara y volcara rápidamente
hacia atrás, lo que podría producir lesiones graves o la muerte.
11. No apague el tractor y no se desplace cuesta abajo sin control. El exceso de
velocidad puede hacer que el operador pierda el control del tracor, ocasionando
lesiones graves e incluso la muerte.
Transporte
1. Utilice rampas de ancho total bien sujetas para cargar y descargar un tractor
para el transporte.
2. Tenga mucho cuidado al cargar o descargar el tractor en un remolque o
camión. Este tractor no debe conducirse subiendo o bajando rampas, ya que
el tractor podría volcar y provocar lesiones personales graves. El tractor se
debe empujar a mano en rampas para cargarlo o descargarlo correctamente.
3. Eleve la plataforma hasta la posición más alta para tener separación para la
carga.
4. No remolque este tractor pues podrían dañarse los motores.
Remolques con su tractor
1. No remolque cargas que superen las 250 libras (113 kg) de peso de arrastre y
nunca supere las 50 libras (22 kg) de peso sobre el punto de enganche.
2. No acople el equipo remolcado excepto en el punto de enganche del tractor.
3. Nunca permita que los niños y otras personas se suban a equipos remolcados.
4. No remolque en pendientes de más de 5 grados (9%). En las pendientes, el peso
del equipo remolcado puede causar pérdida de tracción y pérdida de control, y/o
de la capacidad para detenerse.
5. Siempre tenga mucho cuidado al remolcar con un tractor capaz de hacer giros
cerrados (por ejemplo, tractor de giro cerrado). Realice giros amplios para el
acodillamiento.
6. Desplácese lentamente y deje distancia adicional para detenerse.
Servicio
1. Mantenga el tractor en buen estado de funcionamiento. No use el tractor hasta
que se reemplacen las piezas desgastadas o dañadas.
2. Las cuchillas del tractor son filosas. Envuelva la cuchilla o utilice guantes y
extreme las precauciones cuando les haga mantenimiento.
3. Quite la llave y guarde el tractor bajo techo cuando no lo use. Deje que el
tractor se enfríe por lo menos cinco minutos antes de cargarlo o guardarlo.
4
PRÁCTICAS DE OPERACIÓN SEGURAS
4. Antes de limpiar, reparar o inspeccionar, compruebe que la(s) cuchilla(s) y
todas las piezas móviles se hayan detenido. Apague el tractor y quite la llave.
5. Controle que las cuchillas se detengan completamente en no más de cinco
(5) segundos después de desactivar el control de desactivación de las
cuchillas según el intervalo que figura en el Cronograma de Mantenimiento.
Mida el tiempo hasta la detención con un cronómetro. Si las cuchillas no se
detienen completamente en menos de cinco segundos, su tractor debe ser
reparado por un profesional en un distribuidor de servicio autorizado.
6. Controle el sistema de interbloqueo de seguridad, según el intervalo del
Cronograma de Mantenimiento para un funcionamiento correcto, tal como
se describe más adelante en este manual. Si el sistema de interbloqueo de
seguridad no funciona correctamente, lleve su tractor para que le realicen un
servicio profesional en un distribuidor autorizado.
7. Nunca altere el sistema de interbloqueo de seguridad u otros dispositivos
de seguridad. Compruebe regularmente que estos elementos funcionen
correctamente.
8. Controle el ajuste del perno de montaje de las cuchillas de acuerdo con
el Cronograma de Mantenimiento que figura en este manual. Además,
inspeccione visualmente las cuchillas para detectar la presencia de daños
(por ejemplo: desgaste excesivo, abolladuras, rajaduras). Reemplace las
cuchillas por cuchillas del fabricante del equipo original (O.E.M.) únicamente.
9. El uso de piezas que no cumplen con las especificaciones del equipo original
puede resultar en rendimiento inadecuado y poner en peligro la seguridad.
10. Mantenga todos los pernos, tuercas y tornillos bien ajustados para
asegurarse que la máquina se encuentra en condiciones seguras de
operación. Revise la tabla del Cronograma de Mantenimiento que figura en
este manual para obtener información sobre el intervalo de servicio.
11. Después de golpear un objeto extraño, detenga el tractor, presione el botón
de Encendido/Detención, coloque la llave en la posición OFF y quítela. Revise
el tractor cuidadosamente para detectar daños. Repare los daños antes de
ponerlo en funcionamiento.
12. Para reducir la posibilidad de incendio, quite del motor cualquier
acumulación de césped, hojas y otros desechos. Siga las instrucciones para
el cuidado del tractor posterior al funcionamiento que figuran en la sección
Servicio y Mantenimiento.
13. Controle el funcionamiento del freno con frecuencia, ya que está sujeto a
desgaste durante el funcionamiento normal. Realice el ajustes y servicio que
sean necesarios
14. Nunca intente realizar ajustes o reparaciones al tractor sin antes retirar la
llave.
15. Mantenga o reemplace las etiquetas de seguridad e instrucciones según sea
necesario.
Seguridad Eléctrica en General
1. No exponga el tractor a la lluvia o a condiciones húmedas.
2. No realice ningún servicio al tractor ni manipule componentes eléctricos con
las manos húmedas.
3. No utilice el tractor bajo la lluvia, en condiciones húmedas ni en superficies
mojadas.
4. Para reducir el riesgo de descarga eléctrica, evite el contacto del cuerpo con
elementos conductores con puesta a tierra, por ejemplo, caños metálicos o
cercos de alambre.
5. No utilice el tractor en atmósferas explosivas, por ejemplo, en presencia de
líquidos, gases o polvo inflamables.
6. Para protegerse del riesgo de lesiones o descargas eléctricas, no reemplace
fusibles que hayan saltado. Su tractor debe ser revisado por un profesional
en un distribuidor autorizado.
7. Nunca empape o moje su motor con una manguera. Evite el ingreso de
líquidos en el motor y las conexiones eléctricas. Limpie el tractor después
de cada uso. Consulte la sección Limpieza y Almacenamiento. No utilice
solventes o detergentes fuertes.
Seguridad del Cargador de Baterías
ADVERTENCIA
Únicamente utilice un cargador de batería del OEM (pieza N° 725-07253A)
para cargar las baterías de este tractor. No intente cargar otras baterías con
el cargador de baterías específico de este tractor. Otros tipos de baterías
podrían explotar, causar incendios, lesiones personales o daños materiales.
1. Recargue las baterías únicamente con el cargador especificado por el
fabricante. Un cargador que resulta adecuado para un solo tipo de batería
podría causar riesgo de incendio si se lo usa con otra batería.
2. No utilice el cargador bajo la lluvia, en lugares húmedos o en presencia de
líquidos o gases inflamables.
3. El cargador tiene una placa de identificación que indica el voltaje utilizado.
Nunca conecte el cargador a un voltaje de CA que difiera de este voltaje.
4. No utilice un cable prolongador salvo que sea absolutamente necesario. El
uso de un cable prolongador inadecuado puede generar riesgo de incendio,
descarga eléctrica o electrocución.
5. No utilice cables prolongadores múltiples.
6. Asegúrese de que el cable prolongador sea suficientemente grueso como
para transportar la corriente que toma el cargador. Si el cable prolongador es
de calibre inferior al requerido se producirá una caída del voltaje de línea y
esto dará lugar a pérdida de potencia y sobrecalentamiento. Si está en duda,
utilice cable del calibre más grueso siguiente. A menor número de calibre,
mayor grosor de cable.
TAMAÑO MÍNIMO DEL CABLE PARA CABLES PROLONGADORES DE ARTEFACTOS DE
120 VOLTIOS QUE USAN 0-6 AMPERIOS
Longitud del cable (pies) 25 50 100 150
Calibre (AWG) 16 16 16 14
7. Asegúrese de que los cables estén en buenas condiciones. Revise el cable de
alimentación del cargador de la batería y el cable prolongador periódicamente.
Observe detenidamente para ver si hay deterioro, cortes o grietas en el
aislamiento. Si cualquiera de los cables se daña de algún modo cuando está
enchufado, desconecte el cable del tomacorriente y del cargador. No utilice un
cable dañado. Los cables dañados se deben reparar o cambiar.
8. No use los cables en forma inadecuada. Nunca arrastre ni lleve el cargador
tirando del cable. Mantenga los cables lejos de fuentes de calor, aceite, agua,
bordes filosos y objetos en movimiento. Para desconectar un cable, agarre
siempre el enchufe.
9. No modifique nunca un enchufe, un cable ni un tomacorriente de ninguna
manera.
10. En el(los) circuito(s) o tomacorriente(s) que se usarán con este cargador siempre se
debe suministrar protección con un Interruptor de Circuito por Falla a Tierra (GFCI).
Para proporcionar una medida adicional de seguridad, utilice tomacorrientes con
protección GFCI incorporada.
11. No coloque el cargador de baterías en lugares donde se puedan pisar los
cables, tropezar con ellos o pudieran dañarse.
12. Guarde el cargador de baterías y los cables en un área fresca y seca.
13. Guarde el cargador de baterías y los cables lejos de cualquier líquido.
14. No permita que se introduzcan objetos metálicos pequeños ni materiales, por
ejemplo, lana de acero, lámina de aluminio ni otras partículas extrañas en el
puerto del cargador.
15. No pruebe el cargador con material conductor. Existe el riesgo de descarga
eléctrica.
16. No cubra el cargador de baterías. El cargador de baterías se puede sobrecalentar.
17. No permita que la batería o el cargador de baterías se sobrecalienten. Si se
calientan, deje que los mismos se enfríen. Cargue las baterías únicamente en
temperaturas que se encuentren entre 32º y 104ºF (0º y 40ºC).
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/