Chicago Electric 60713 Owner's manual

Chicago Electric
Brand
Chicago Electric
Model
60713
Category
Power tools
Type
Owner's manual

This manual is also suitable for

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2020 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight To ols .
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Too ls re qui red fo r ass emb ly an d s erv ice m ay not be i ncl ude d.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
Owner’s Manual & Safety Instructions
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 20c
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2020 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Too ls re qui red fo r ass emb ly an d s erv ice m ay not be i ncl ude d.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 57226
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
General Power Tool Safety Warnings
Read all safety warnings and instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work Area Safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
2. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
3. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
4. When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
5. If operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply. Use of
a GFCI reduces the risk of electric shock.
Page 3For technical questions, please call 1-888-866-5797.Item 57226
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while operating
power tools may result in serious personal injury.
2. Use safety equipment. Always wear eye
protection. Safety equipment such as a
dust mask, non-skid safety shoes, a hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energizing power
tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
7. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must be ANSI-
approved and breathing protection must be NIOSH-
approved for the specific hazards in the work area.
Power Tool Use and Care
1. Do not force the power tool. Use the
correct power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk
of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Safety Warnings Common for Grinding, Sanding,
Polishing, or Abrasive Cutting Operations
1. This power tool is intended to function as a
grinder, sander, polisher or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power
tool, it does not assure safe operation.
Page 4 For technical questions, please call 1-888-866-5797. Item 57226
3. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their RATED SPEED can break and fly apart.
4. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
5. The shank of the accessories used must properly
fit the Collet of the power tool. Accessories
with arbor holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
6. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad
for cracks, tear or excess wear. If the power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
7. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
work piece fragments. The eye protection must
be capable of stopping flying debris generated
by various operations. The eye protection must
be capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtering out particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
8. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of work
piece or of a broken accessory may fly away and
cause injury beyond the immediate area of operation.
9. Position the cord clear of the spinning
accessory. If you lose control, the cord may
be cut or snagged and your hand or arm may
be pulled into the spinning accessory.
10. Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
11. Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
12. Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
13. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
14. Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
15. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
16. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
17. Do not leave the tool unattended when it is
plugged into an electrical outlet. Turn off the tool,
and unplug it from its electrical outlet before leaving.
18. Use clamps (not included) or other practical
ways to secure and support the workpiece
to a stable platform. Holding the work by
hand or against your body is unstable and may
lead to loss of control and personal injury.
19. This product is not a toy. Keep
it out of reach of children.
20. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields
in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure. In
addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit Interrupter
(GFCI) should also be implemented – it
prevents sustained electrical shock.
21. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
Page 5For technical questions, please call 1-888-866-5797.Item 57226
Vibration Safety
This tool vibrates during use. Repeated or long-term
exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-
ups to ensure medical problems are not being
caused or worsened from use. Pregnant women
or people who have impaired blood circulation
to the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration when there
is a choice between different processes.
5. Include vibration-free periods each day of work.
6. Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. Never remove the grounding prong from
the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
Double Insulated Tools: Tools with Two Prong Plugs
Outlets for 2-Prong Plug
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
2. Double insulated tools may be used in either
of the 120 volt outlets shown in the preceding
illustration. (See Outlets for 2-Prong Plug.)
Page 6 For technical questions, please call 1-888-866-5797. Item 57226
Extension Cords
1. Grounded tools require a three wire extension
cord. Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases, you
must use a heavier gauge extension cord. Using
extension cords with inadequately sized wire causes
a serious drop in voltage, resulting in loss of power
and possible tool damage.
(See Table A.)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord to make
up the total length, make sure each cord contains at
least the minimum wire size required. (See Table A.)
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR
EXTENSION CORDS
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD LENGTH
25’ 50’ 75’ 100’ 125’ 150’ 175’ 200’
0-10.0 18 18 16 16 14 14 12 12
10.1-13.0 16 16 14 14 14 12 12 12
13.1-15 14 14 12 12 12 12 12 -
15-18 14 12 12 12 12 12 - -
TABLE A
Symbology
Double Insulated
V
Volts
~
Alternating Current
A
Amperes
n
0
xxxx/
min.
No Load Revolutions per Minute (RPM)
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.
Page 7For technical questions, please call 1-888-866-5797.Item 57226
Specifications
Electrical Rating 120VAC / 60Hz / 1.4A
Speed 8,000 – 35,000/min
Collet Sizes 1/8" & 1/16". Diameter
Accessory
Diameter
1-3/8" (35mm) Max
Accessories
6 Sanding Discs
5 Sanding Drums
4 Grinding Stones
3 Cut Off Wheels
2 Diamond Burrs
2 Brass Collets
2 Mandrels
1 Buffing Wheel
1 Square Stone Dresser
1 Wire Wheel Brush
1 Drill Bit
1 Flat Wrench
1 Soft Brush
Page 8 For technical questions, please call 1-888-866-5797. Item 57226
Instructions For Putting Into Use
Read the ENTIRE “IMPORTANT SAFETY INFORMATION” section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before assembling or making any adjustments to the tool.
Note: For additional information regarding the parts listed in the following
pages, refer to the Assembly Diagram near the end of this manual.
Set-Up
Your Rotary Tool will require some set-up prior to operation.
To ass ist y ou wit h set -up , ple ase r efer to the fol l o wi n g
instructions. Also see the Parts List and Assembly Diagrams
near the end of this manual.
It is important that you read the entire manual to become
familiar with the unit BEFORE you use the Rotary Tool.
Before setting-up your Rotary Tool, be sure that you have
all parts described in the Parts List.
Assemble attachments based on the intended use of
the tool.
Set-up and disassemble your Rotary Tool Set for each use.
Put back all pieces in the case provided and store in the
case to ensure that no pieces are lost.
To Insert Accessories:
1. Insert Collet (2, Accessory C) into the shaft.
Slide the Collet Nut (1) over the Collet. Insert
the desired accessory fully into the Collet.
2. Press down on the Lock Button (4) while turning
the Collet Nut. The shaft will click into place.
3. With the Shaft locked in place, use the
Wrench (Accessory I) to tighten the Collet Nut.
Note: Some cutting wheels, polishing tips and
accessories need to be attached or inserted into
another shaft or mandrel to be used. In these
cases, please note the following instructions.
4. Thread the accessory onto the screw of the
Mandrel (Accessory L) into the Collet. Following
the preceding steps, tighten the Collet Nut.
To Remove Accessories:
1. Press down on the Lock Button while
turning the Collet Nut counterclockwise.
You will feel the Shaft click into place.
2. With the Shaft locked in place, use the Wrench to
loosen the Collet Nut and remove the accessory.
Work Piece & Work Area Set-Up
1. Designate a work area that is clean and well-
lit. The work area must not allow access by
children or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. Secure loose work pieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects, such
as utility lines or foreign objects, nearby that
will present a hazard while working.
5. You must use personal safety equipment
including, but not limited to, ANSI-approved
eye and hearing protection, as well as
heavy work gloves and work apron.
6. Before beginning work, plan and provide
for sparks and debris that will fly off the
work surface. CAUTION! Always have
access to a type AAA fire extinguisher.
Page 9For technical questions, please call 1-888-866-5797.Item 57226
Operating Instructions
TO PREVENT SERIOUS
INJURY: Grip the tool firmly.
To assist you with operation, please refer to the Assembly
Diagram and Parts List near the end of the manual.
Never force the tool or attachment to do the work of a
larger industrial tool. It is designed to do the job better
and more safely at the rate for which it was intended.
1. For most uses, it is helpful to grasp the tool
much like a pencil. This will allow the finest
control of the tool. Before starting on your
actual workpiece, practice a similar action
(drilling, cutting, polishing) on a scrap piece.
2. Apply only slight pressure. Let the tool do the
work. To prevent heat build-up, do not cover
the air vents with your hands during use.
3. Use the Square Stone Dresser (Accessory E)
to maintain the proper shape of
grinding stones and wheels.
4. Use the Mandrel (Accessory L) to
attach the Sanding Discs (Accessory A),
Buffing Wheel (Accessory B), and
Cut Off Wheel (Accessory H) to the Collet.
See “To Insert Accessories:” on page 8
for more information.
Setting the Speed
1. The Rotary Tool has a Speed Control Dial (12)
which clicks into the different speeds, from
highest to lowest. Move the Dial to the
highest setting for the speed with maximum
RPM (35,000). The Tool has five other adjustable
settings, the lowest being for 8,000 RPM.
Note: Always start work at the lowest
RPM setting (8,000 RPM).
2. CAUTION! Do not change the speed while
the Rotary Tool is working. Remove Tool
from workpiece before adjusting speed.
3. Slow speeds of 15,000 RPM or less are best for
cleaning, polishing, plastics, precious metal, and
delicate materials. Some materials melt at lower
temperatures and should be cut at lower speeds.
Higher speeds are best for drilling, carving, cutting,
shaping, and routing. Hard materials like iron, steel
and hard wood should be worked on at high speeds.
See “Recommended Accessory Speeds”
on page 10 for more information.
4. Press the Power Switch on. ON is noted
by a line (l), and OFF is noted by (O).
5. When finished using the tool, turn OFF the
Power Switch and unplug the tool. Allow
the tool to cool, then wipe clean and
store all parts in the included case.
Page 10 For technical questions, please call 1-888-866-5797. Item 57226
Accessory Uses Soft Wood Hard Wood
Laminates/
Plastic
Steel
Aluminum,
Brass, etc.
Shell/Stone Ceramic Glass
Sanding
Discs
Finishing 12,000-17,000 12,000-17,000 8,000-10,000 - 8,000-10,000 - - -
Buffing
Wheel
Polishing - - 7,000-12,000
12,000-
15,000
12,000-15,000 12,000-15,000 12,000-15,000
12,000-
15,000
Sanding
Drums
Shaping 8,000-35,000 8,000-35,000 8,000-17,000
25,000-
35,000
25,000-35,000 8,000-35,000 8,000-35,000 -
Wire Wheel
Brush
Cleaning 9,000-11,000 9,000-11,000 -
9,000-
11,000
9,000-11,000 9,000-11,000 - -
Drill Bit
Drilling
a hole
25,000-35,000 18,000-35,000 8,000-11,000 - 12,000-17,000 - - -
Cut Off
Wheels
Cutting Off - - 8,000-11,000
25,000-
35,000
25,000-35,000 25,000-35,000 25,000-35,000 -
Soft Brush Cleaning 9,000-11,000 9,000-11,000 9,000-11,000
12,000-
17,000
8,000 - - -
Diamond
Burrs
Etching,
Engraving
25,000-35,000 18,000-24,000 - - - 25,000-35,000 25,000-35,000
25,000-
35,000
Grinding
Stones
Sharpening 25,000-35,000 25,000-35,000 -
18,000-
24,000
9,000-11,000 12,000-17,000 25,000-35,000 -
Recommended Accessory Speeds
Page 11For technical questions, please call 1-888-866-5797.Item 57226
Maintenance And Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch to it’s OFF position and unplug the tool from its electrical
outlet before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning & Maintenance
1. BEFORE EACH USE, inspect the general condition
of the tool. Check for loose screws, misalignment
or binding of moving parts, cracked or broken
parts, damaged electrical wiring, and any other
condition that may affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with a clean cloth.
3. Periodically blow dust and grit out of the motor
vents using dry compressed air. Wear ANSI-
approved safety goggles and NIOSH-approved
breathing protection while doing this.
4. WARNING! TO PREVENT SERIOUS
INJURY: If the supply cord of this power
tool is damaged, it must be replaced only
by a qualified service technician.
Accessory Storage and Handling
1. Handle accessories carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.
2. Store accessories in the carrying case. Store in a
dry area and at above freezing temperature. Any
grinding or cut-off wheels exposed to humidity or
freezing temperatures must not be used. Keep
all accessories out of the reach of children.
Page 12 For technical questions, please call 1-888-866-5797. Item 57226
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Internal damage or wear. (Carbon
brushes or switch, for example.)
1. Check that cord is plugged into 120V outlet.
2. Check power at outlet. If outlet is
unpowered, turn off tool and check
circuit breaker. If breaker is tripped,
make sure circuit is right capacity for
tool and circuit has no other loads.
3. Have technician service tool.
Tool operates slowly. 1. Tool is set on slow speed setting.
2. Excess pressure applied to workpiece.
3. Power being reduced by too lengthy
or small diameter extension cord.
1. Increase speed setting.
2. Decrease pressure, allow
tool to do the work.
3. Eliminate use of extension cord. If
an extension cord is needed, use
one with the proper diameter for
its length and load. See Extension
Cords in GROUNDING section.
Performance
decreases over time.
Worn internal components. Have qualified technician service tool.
Excessive noise
or rattling.
Internal damage or wear. (Worn
bearings, for example.)
Have technician service tool.
Overheating. 1. Forcing tool to work too fast.
2. Blocked motor housing vents.
3. Motor being strained by too lengthy
or small diameter extension cord.
1. Allow tool to work at its own rate.
2. Wear ANSI-approved safety goggles
and NIOSH-approved dust mask/
respirator while blowing dust out
of motor using compressed air.
3. Eliminate use of extension cord. If
an extension cord is needed, use
one with the proper diameter for
its length and load. See Extension
Cords in GROUNDING section.
Tool does not
grind, sand or
brush effectively.
1. Disc accessory may be loose on
Spindle.
2. Disc accessory may be damaged,
worn or wrong type for the material.
1. Be sure disc accessory is of correct
dimension and Collet Nut is tight.
Check tightness of Collet Nut or
threaded disc accessory on Spindle
2. Check condition and type of disc
accessory. Use only proper type
of disc accessory. Accessories
must be in good condition.
Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power
supply before service.
Page 13For technical questions, please call 1-888-866-5797.Item 57226
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT,
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14 For technical questions, please call 1-888-866-5797. Item 57226
Part Description Qty
A Sanding Disc 6
B Buffing Wheel 1
C Brass Collet 2
D Sanding Drum 5
E Square Stone Dresser 1
F Wire Wheel Brush 1
G Drill Bit 1
Part Description Qty
H Cut Off Wheel 3
I Flat Wrench 1
J Soft Brush 1
K Diamond Burr 2
L Mandrel 2
M Grinding Stone 4
Accessories Parts List
A
B
C
D
E
F G H
I J K L M
Page 15For technical questions, please call 1-888-866-5797.Item 57226
Part Description Qty
1 Collet Nut 1
2 Collet 1
3 Nose Cap 1
4 Lock Button 1
5 Base 1
6 Bearing 2
7 Fan 1
8 Rotary 1
9 Left Housing 1
10 Carbon Brush 2
Part Description Qty
11 Screw 6
12 Speed Control Dial 1
13 Stator 1
14 Trim Board 4
15 Power Switch 1
16 Hanger 1
17 Cord Sleeve 1
18 Plug 1
19 Cord 1
20 Right Housing 1
Main Unit - Parts List & Assembly Diagram
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and
warrants to the original purchaser that this product is free from defects in materials and workmanship for the period
of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal
wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or
for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not
apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof
of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the
defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we
cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Chicago Electric 60713 Owner's manual

Chicago Electric
Brand
Chicago Electric
Model
60713
Category
Power tools
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents