Binatone SW-GE1008F User manual

1

SW-GE1008F

Ethernet Switch

2

Item Listing

Be careful to open the box, and check the accessories as follows：

1. switch

2. console wire

3. Adaptor

If any damage of products or shortage of accessories inside the box, please contact the local distributor

3

Chapter 1. Introduction of user manual

Thanks for purchasing SW-GE1008F 8 + 2 full gigabit managed switches. This switches provide various

management functions, the overall performance is superior, simple to use, is the ideal choice to improve your

team performance!

1.1 Usage

Purpose of this manual is to help you to use the SW-GE1008F series full gigabit managed switches

intimately and conveniently.

1.2 Agreement

The following sections in this manual, all for SW-GE1008F switches

1.3 Summary of user manual

Chapter 1：Introduction of user manual

Chapter 2：Product overview. Describe the structure and the basic characteristics of the switches

Chapter 3：Installation guide. To guide you the basic installation steps of switch

Chapter 4：Basic concept of switches

Chapter 5：WEB management. About how to use the WEB connection and manage the switch.

Chapter 6：Out-of-band management. About how to use the out-of-band management to manage the switch

4

Chapter 2. Product Introduction

2.1 Product introduction

SW-GE1008F managed switches is compatible with the IEEE 802.3 u 802.3, 802.3, 802.3 x and z Q,

802.1 p, 802.1 D and 802.3 ab standard.

SW-GE1008F switch's front panel provides eight high-performance 10/100/1000 Mbps full duplex

RJ45 port, 2 100/1000 Mbps SFP port.SW-GE1008F switches support WEB management and Out-of-band

management. Provide various management functions, the overall performance is superior, simple to use, is

the ideal choice to improve your team performance!

2.2 Key Features

 Compatible with IEEE 802.3 Ethernet、IEEE 802.3z、802.3x、802.1Q、802.1p、802.1d

and 802.3ab.

 The backplane bandwidth can reach 20Gbps storage and forward architecture

 Supports up to 16 802.1Q tag-based VLAN

 8 k MAC address

 Support address learning of each port

 Support Port Trunk

 Support Port Mirror

 Support broadcast storm control, can effectively control the various broadcast packets

forwarding rate, avoid the broadcast storm

 Support port security, including static MAC address binding

 Support RSTP and Loop Detect

 Support WEB and RS232 out-of-band management

 Support DHCP

 Through TFTP, HTTP, XMODEM to upgrade the system software, at the same time

support the TFTP, HTTP download and upload to the configuration file

 SW-GE1008F managed switches fully compliant with IEEE 802.3u, 802.3z, 802.3x,

802.1Q, 802.1p, 802.1D and 802.3ab standards.

 Built-in high quality switching power supply, stable and reliable

 1U all steel enclosure, supporting the hanging installation

5

2.3 Specifications

Table 2-1 SW-GE1008F series technical index table

2.4 Package content

Please refer to the packing list

Model

SW-GE1008F

Standard

IEEE 802.3 Ethernet、802.3x、802.1Q、802.1p、IEEE802.1D and 802.3ab

Interface

8 个 1000Base-T , 2 serdes port

Network Medium

10BASE-T: Cat3 or above Cat3 UTP or STP

100BASE-TX:Cat5 UTP or STP

1000BASE-SX：Multi-mode Fiber

1000BASE-LX：Multi-mode fiber or single-mode fiber

1000BASE-T：Cat5 UTP or STP

MAC Address Table

8K

Backplane/Bandwidth

20G

Filtering and

forwarding rate

10Mbps：14880pps；100Mbps：148800pps； 1000Mbps：1488000pps

LED

indicator

10/100M/

1000M

Link/Act

other

Power；SYS

Size

230*145*40mm

Environment

Operating Temperature: 0℃~40℃ (32℉~104℉);

Storage Temperature: -40℃~70℃ (-40℉~158℉)

Operating Humidity: 10%~90% non-condensing

Storage Humidity: 5%~90% non-condensing

Power

9-15VDC

RPS Power

12V battery

6

Chapter3. Switches Installation Guide

3.1 Installation

Support installed on the frame, hanging installation, support directly put on the desktop.

Before installation, please read the following precautions

 Please put the switch in ventilated, dry place

 Switch power supply outlet distance must be within 1.5 meters

 Ensure the power wire is reliably connected to the rear panel of switch between the power socket interface

and power supply.

 Please use the included power wire, power supply voltage must adapt to the input voltage range of the

switches

 Ensure the switch has good ventilated and cool environment, and do not place heavy objects on the switches

 The attachments (including but not limited to: the power wire, etc.) can only be used for this switch, banned

for other products.

The installation way on the table

1） Put the switch directly on the desktop

The installation way on the frame

Description: SW-GE1008F can be fixed on the frame by installed hangers(non-standard rack).SW-GE1008F

switches also support hanging installation

Installation procedure:

1） Check the grounding and stability of the rack

2） Two L shape bracket installed on both sides of the switch panel (provide screw)

3） Place the switch on the cabinet of a bracket, according to the actual situation, the rack guide mobile

switches to the right place

4) Then use screws to fix install hangers in the corresponding groove of the cabin to ensure that the switch

steady installed in the rack.(Users should bring along their own screw)

Picture 3-1 Installing hangers

7

Picture 3-2 Installing the switch to the rack

Hanging installation method

1) Drilling on the wall and fixing the screw

2) Make sure that the length of the screws like switch’s hang hole the fastening level of screws should be

greater than the actual load.

3）Put the switch smoothly on the wall.

Power up

Switch power supply is 9 to 15 v dc input voltage range the built-in power supply system of switch can be

based on the actual input voltage automatically adjust the operating voltage When normal Power up the switch

power indicator in the front panel will turn on.

Attention：

When the power supply system failure or temporary power failure, to ensure that the switch is not damaged

by the sudden large current, be sure to pull down the power wire of switch from the power supply socket. When

the power supply back to normal, and then plug in the power wire.

3.2 The appearance of the switch

To describe the switch’s front panel and rear panel in detail 。

The front panel

SW-GE1008F switch’s front panel have 8 10/100/1000 Mbps port,2 SFP ports and related LED lights, as shown

in the figure below：

Picture 3-2 The front panel of SW-GE1008F

8

1）8 10Base-T/100Base-TX /1000Base-TX RJ-45 ports

The right side of the Console port is eight 10/100/1000 Mbps port, they support 10 Mbps, 100 Mbps or

1000Mbps bandwidth connection equipment, support Auto-Negotiation. To configure the speed control,

duplex control, safety control, flow control and the broadcast storm of each port by WEB management Each

port corresponding to a double color LED lights, red indicate 10/100M Link/Act, green indicate 1000M

Link/Act.

2）2 100/1000Mbps SFP ports

The right side of the front panel is 2 100/1000 Mbps SFP ports, each corresponding to a LED indicator, red

indicate 10/100M Link/Act, green indicate 1000M Link/Act.

3）1 console configuration port

Locating on the right side of LED indicator in the front panel,

it is the out-of-band management and computer connection interface, to configure the system information,

network parameter and safety management, etc by providing a serial port line.

LED indicators

1）Group 1 ~ 10 of LED indicator are on the left side of the front panel.

When a regular port connect with 1000 Mbps device, corresponding to the LED indicator light is green

normally on. When data transmission the indicator is flashing.

When the port work in 100Mbps or 1000Mbps full-duplex state, corresponding to the LED indicator light is

green on.

2）Power indicator

Its location on the left side of panel, when the switch’s power is connected, this indicator light is green on. If

the light is out, check whether connect the power supply.

3）SYS indicator（system indicator）

。Its location on the left side of panel. When the switch has normal boot ,this indicator light is green on.

When the switch is power on self test, the indicator light is flashing. Check the switch losing power if the

indicator light is not bright.

The rear panel

The rear pane of switch with a dc power supply interface, an external power supply interface and a Reset

button. Working voltage range: 9-15 VDC

Picture 3-3 The rear panel of SW-GE1008F

1） Dc power supply interface（Picture 3-3 the right side）

This is a DC power supply socket, plug the DC adapter into the socket, the power wire plug from the socket,

and the other side from the ac power

2）The external power supply interface（Picture 3-3 middle）

It can be external to the 12 v battery redundant power supplies

3）The Reset button（Picture 3-3 the left side）

Remove the switch Settings and restore the factory Settings

9

3.3 Announcements

 Please pay attention to placed switches, that will cause serious consequences when it fall.

 It should be under the correct power supply to work properly, please confirm the power supply before using.

 In order to reduce the risk of electric shock, do not open the enclosure when it work, even in the case of no

charge, also do not to open.

 When the switch connect with workstation, server, the HUB or the other switches, if the cable to use is the

UTP (unshielded twisted pair), its length is not greater than 100 meters.

 Cat3 or above Cat3 UTP for 10Base-T Ethernet.

 Cat5 or above Cat5 UTP for 100Base-T Ethernet.

 Cat5 or Cat6 UTP or above for 1000Base-T Ethernet.

 The reticle can be inserted or pulled out of switch’s port when it work and won’t interrupt it.

 Before cleaning switch, please pull out the attaching plug of switch and use wet fabric to wipe, liquid

washing is not available.

 Don't put the switch in the water side or damp places, and to prevent water and moisture into the switch

cabinet

 When placed in the switch, please avoid dusty and strong electromagnetic interference region

Chapter 4. Configuration and usage

10

4.1 The system global configuration

Global configuration for switch system is mainly to set switch network parameters (IP address, subnet mask,

gateway), user name and password, the Console and the maximum idle time of Web Console, the MAC address

table aging time, VLAN configuration mode and the parameters of VLAN and SNMP management of the switch

management, etc

System information

Including switch MAC address, such as software version and hardware version of basic information

Password Setting

In order to protect the switch’s setting security, only with right password users to be able to login to

the management interface of switch for configuration management. The password for the administrator can

be set , the default password is admin.

Switch IP address and VLAN ID management

SW-GE1008F switch can be manually set the IP address, subnet mask and default gateway.

Obtain an IP address if the DHCP is enabled, manual set doesn't work. Factory switches

default IP address is 192.168.10.1, mask is 255.255.255.0.When using, please according to

the actual situation of their network to reset these parameters. Switch management VLAN ID

is switch CPU’s. So based on 802.1QVLAN,the management of PC connected port PVID and

managed VLAN ID are the same to manage the switch.

DHCP Function

SW-GE1008F provides obtaining an IP address automatically by DHCP. Default state of the DHCP

function is closed, it can be configured manually switch IP address and subnet mask and default gateway

under the closed position.

================================================================

DHCP function should be paid attention to use

1） Changing the DHCP status (open or closed),a new state to take effect after the switch restart.

2） Switch obtain address information lease from the DHCP is infinite, even if the DHCP server is

configured with limited lease, switch still regard it indefinitely.

 The biggest aging time of dynamic address table

Switch always maintain a Dynamic MAC Address Table internally.MAC address also known as physical

address, is the address of the only network nodes, this address is 6 bytes, it identifies a network device from a

local area network (LAN).Dynamic MAC address table has two contents: MAC address and their

corresponding port number. Dynamic address table is updated dynamically, each dynamic address records

have limited service life, the length of life to be controlled by the largest aging time. If the record is not to

learn within the limited life, it will be deleted, this process is called aging. This time we call it "the biggest

aging time", it is measured in seconds. The switch can be set the biggest aging time, set the range of 10 to

65535 seconds, set to 0 means no aging, it is 300 seconds under the default state.

 TFTP

This series switches support using the TFTP server to download switch file, downloading and uploading

the configured file. This feature can be closed and opened and it close under default.

11

4.2 TFTP client function

The using type and working mode of port has a direct relationship with configuration, here introduced the

type and support property of port.

The type of port and working mode

The type of port in different working mode is different, the specific port stated below

10/100/1000M adaptive RJ45 port

If ports work in electric mode, these ports support 6 kinds of working mode

1）10Mbps-Half duplex 2）10Mbps-Full duplex

3）100Mbps-Half duplex 4）100Mbps-Full duplex

5）1000Mbps-Full duplex 6）Port auto negotiation

The switch provides Settings function of the port negotiation, make the device segment exchange

information about their respective functions in a link, which can achieve the best operating mode on the

link to realize automatic adjustment of transport (full duplex or half duplex) and the transmission speed

function (10 Mbps, 100 Mbps or 1000 Mbps).Port for optimizing processing.

A. 1000BASE-TX port support mandatory ability：

1） Mandatory-100M/FD

2） Mandatory-1000M/FD

flow control

Full-duplex mode with flow control in accordance with the IEEE 802.3 x based on PAUSE function

Equipment resources shortage in the network, will lead to the equipment has no ability to continue to

receive data, device can transmit outward PAUSE frame at this time, the equipment which received the

frame will stop for a period of time to send operation according to PAUSE frame data, the inactive time is

measured in Quanta, the length is associated with physical link a Quanta in physical link above 512 bits of

data transmission time.

Half duplex mode with the Back - pressure flow control function.

When two devices to send data on the Internet at the same time, can produce conflict, in the event of

conflict, the sending site will detect the conflict, they will automatically stop a random time interval, and resend

again, but it will reduce the efficiency of the network. So the network devices will intercept on the network to

determine whether the network is available, when lack of equipment resources will start the flow control,

sending a set of carrier signal pulse sequence (false conflict signal), equipment detected on the network carrier

signal and will think the network due to being used by other equipment conflict, other sites under half duplex on

the network will stop sending data.

4.3 VLAN（Virtual Local Area Network）

When the switch handle multiple network management tasks at the same time, set up the virtual local area

network, can reduce resource consumption, improve the efficiency of the network. Virtual local area network is

composed of multiple devices of flexible equipment group, the equipment can be located in anywhere in the

12

network, and communication connection between devices as are in the same physical partitions. Through the

virtual local area network (LAN), can divide the network into multiple partitions, but do not need to change the

physical connection between the devices

SW-GE1008F switches support Tag 802.1 Q VLAN mode

802.1Q Tag VLAN

Based on the Tag of 802.1 Q VLAN with VID to divide different VLAN, when the data frame through the

switch, switch according to the Tag header VID information of frame to identify their VLAN (but if frame

without the Tag header, then the application frame through the port by default VID information to identify their

VLAN), which makes all belong to the data frame of the VLAN, whether single site frame, multiple frames or

broadcast frame, will be limited in the logical VLAN. This will make the group able to communicate with each

other, each other between the host and not affected by other hosts, just as they exist in separate VLANs

In the initial, VLAN switches, mutual recognition of each vendor can't compatible.IEEE802.1Q virtual

local area network (LAN) - the new standard after the founding, the equipment of different

manufacturers can use in a network at the same time, the switch which support IEEE802.1Q can

communicate with other switches.IEEE802.1Q defines a new frame format, it's behind the standard

Ethernet frame source address joined a tag header.

Picture 4-1 802.1Q tag header

Set the Tag VLAN, there are five configuration to consider：

1） VLAN ID

1-4094。Set the VLAN identifier, to identify a particular VLAN, SW-GE1008F lets you set

the VLAN ID of the range of 1-4094

2） VLAN Aware

Used to determine the input packets if put on the Tag, is based on the VLAN ID Tag come

forward or on PVID

3）The output of the port rules（Tag/Untag）

Identify whether or not to bring the output of the frame from the port tag. The Tag says the

port forwarding the frame with the Tag header, even if the frame without the Tag when received;

Untag show the port from the frame without the tag, even if the frame with the tag when received

4）The default port PVID

When the switch is not obtain a frame of the tag to belong to which VLAN (Untagged

frames), then the default VID of receiving port to determine the frame in which VLAN for

forwarding. The default VID port Settings in the range of 1-4094

DA

SA

Type

Data

CRC

DA

SA

Tag

Type

Data

CRC

0X8100

Priority

CFI

VLAN ID

13

5）Port input filtering

When open port input filtering, the port will check the VID of received frame, if the port is

not belong to this identified VID and VLAN discards the frame. When receiving the frame

without the tag, to filter according to the receiving port's default VID

6）The types of port receives packets

The switch can set the port to receive the packet type, divide into all types of data packets,

including tagged and untagged Or receive only tagged packets

Manage VLAN

A series of switches support management VLAN Settings, only via the members of the VLAN port can

manage the switch based on the management of the Web and the SNMP management, etc. If also opened the

switch’s DHCP function, then the DHCP server can assign IP or other information to the exchange only by a

member of the management VLAN ports

4.4 Trunk

Trunk provides a port polymerization mechanism, it can connect several low-speed together, forming

a high-speed connection. For example, the four 1000 Mbps full-duplex Ethernet port to form the total

bandwidth at 8000 Mbps connection together by Trunk technology , these ports can be view as a port

After setting Trunk, the switch from the outside and the Trunk and Trunk ports in a VLAN other port

load automatically assigned to the various ports in the Trunk.SW-GE1008F Trunk load balancing

allocation is based on the source address of the frame and the destination address, can make the load

for uniform distribution in each port of Trunk.

When one member of the Trunk link disconnect, switches automatically distribute the data on the link of

Trunk, the other link when disconnect the link will restore to the original load distribution.

Set up rules of Trunk：

1） SW-GE1008F support the Trunk quantity is 8, port quantity for 2 ~ 10 in each group

================================================================

What should pay attention to set up a truck：

1）At the time of setting Trunk, either create Trunk or adding a port to the Trunk, to join the members

of a Trunk port will be deleted from all of the VLAN. If remove members from the Trunk port or

delete the whole Trunk, the original members of the Trunk port will return to its original VLAN.

2）The effect between the Trunk and MAC address binding, port mirror

================================================================

4.5. Port Mirror

Copy a send/receive frames to a port , forwarded to the specified port (mirror), so that network management

personnel can analyze and evaluate mirror image data frame of the port

===================================================================

14

Note: in SW-GE1008F, at the same time can be only one port is set to mirror port, mirrored there can be

multiple, and mirror ports and the mirrored should be in the same VLAN.

4.6 Broadcast storm control

Broadcast storm refers to broadcast frame on the network by the number has increased

dramatically and affects normal network communication of the abnormal phenomenon.

Broadcast control allows the port to appear on the network broadcast frame reaches a certain

amount of control, in order to prevent the broadcast storm.SW-GE1008F port supports various

types of broadcast packets forwarding rate, broadcast packet forwarding speed rate, rate of DLF

packet forwarding .Also supports including ICMP packet forwarding rate at the same time, the

study frame of the forward rate, multicast packets forwarding rate, prevent malicious attacks in

the network, also can turn off these control. The control range of various data confirmed to 1

Kbps, 2 Kbps, 4 Kbps, 8 Kbps, 16 Kbps, 32 Kbps, 64 Kbps and 128 Kbps and 256 Kbps

4.7 QoS

SW-GE1008F provides frame transmission mechanism for different priority (priority), according to the

transmission level table switches will receive priority mapped to the frame transmission level, high level of

frame will be priority. Classification can be set based on the priority of port priority and DSCP priority, 802.1 p.

The user can select the current priority classification criteria.SW-GE1008F support four priority queue.

Based on the port priority

If the current QoS options based on port priority, each port of switch can set the priority queue, support four

priority queue, for receives frames of port, whether the frame with priority information, switches will be

based on the port priority queue for processing.

Base on 802.1P priority

Under the Port VLAN mode, for Port receives the frame, whether the frame with priority information,

switches will be based on the default Port priority for processing. In the Tag VLAN mode, if the port

receives the frame without head Tag, the default priority is based on port for processing; If the head

port receives the frame with the tag, switches will be based on the frame of the tag header contains the

priority corresponding priority queue for processing.> a priority queue

DSCP priority

DSCP (Difference Service of Class Priority) Service type is an 8 bit of IP TOS field in the first 6 bit.

Using to represent a priority, without this series switches provide basis on DSCP priority queue the

division of functions.6 bit DSCP is 0 ~ 64, can be mapped to different four priority queue.

4.8 Switch file update

15

SW-GE1008F provides file update feature, can easily upgrade switch software and update configuration

files, currently used at the same time can upload switch configuration files to backup .

The file transmission

Web interface provided file upload and download function by the HTTP protocol. Including switches

software update and backup configuration file ,update upload and download

Administrators can also command achieve file transfer function by the serial port of the CLI. Through

the TFTP Server to update the switches file, download the files provided by the TFTP Server to switch, so

as to realize the upgrade and update of switching software; At the same time, through the file upload

function can be uploaded the current configuration files of switch via TFTP.

===========================================================================

Note: File Transferring

1） TFTP server should contain the files which needed to update when TFTP download; At the same

time, the TFTP server should be ensured in the running state of specified machine.

2） The system need to be restarted to take effect after the TFTP download switch software.

3） Switch download software through the WEB page, software named SW-GE1008F. WRP, case

can be written.

Chapter 5 Web Management

16

5.1 Overview

This switch be used WEB approach to manage. Users can use the WEB browser to login switches, friendly

and intuitive management interface will let you feel configuring switches is an easy thing.

5.2 Web Server

First start the switch, and make sure that the machine (the client) connect with SW-GE1008F .The IP

address of the switch is 192.168.10.1, Enter “http://192.168.10.1” in the browser's address bar, then hit ENTER,

you will see the following dialog:

Picture 5-6 Enter dialogue diagram

In the specified password input box to enter the password (the default password is "admin"), click the

"submit" button, switch into the WEB management page

Note：

The default password of switch is set up in factory. You can also modify the password in the switch system

password Settings page. If you back to factory Settings, the user's own password setting will be deleted, only

keep the password "admin"

5.3 The WEB management page and operation method

As shown in picture 5-7, at the left side of the page is a functional menu page;Page on the right side of the

large area is the main window to be used for functional configuration.

17

Picture 5-7 The SW-GE1008F WEB home page

Picture 5-8 Function Menu

As shown in 5-8, the left side of the function menu is a list , the menu is divided into two layers, the main

18

and secondary items, each item has been launched into the form of a list; If you want to set up the other items,

just click on the corresponding option, the main window will switch to the page of setting .Due to network speed

and load of switch work, the menu will be twice time interval shorter on a click to respond , as long as the

attention to extend click interval at this time

The following lists the main and secondary items of function menu :

 System configuration: global configuration, port configuration, 802.1 Q VLANS configuration, RSTP, port

trunking, port mirror configuration, port isolation, broadcast storm control, self loop detection, quality of

service configuration

 System status monitoring: port statistical information

 System maintenance: warm start, restore the factory Settings, system upgrades, system configuration file

transfer and exit.

Note：

All changes of switch Settings only after click "ok" button will take effect.

5.3.1 System Configuration

 Global Configuration

Mainly includes the following Settings (the following figure)

Picture 5-9 Advanced Settings

 MAC address: switch MAC address

 Software version: switches running software version

19

 Hardware version: switches running hardware version

 IP address: every switch should have its unique IP address, to be used communicated with the host web

applications (such as TFTP). Switch IP address Can be changed in order to match the specific network.

 Default gateway: when the packet destination address does not belong to address book of network

workstation, the packet will be forwarded to the default gateway

 VLAN management: base on 802.1Q VLAN, the switch managed port‘s VLAN ID are the same with the

managed VLAN ID that switch can be managed.

 Switch’s name: identify of switch in the network.

 Password: login password

 The Web's largest idle time: Set Web management automatic refresh time unit is minute.“5 min”、“10 min”、

“20 min” show that Web management automatically refresh time for 5 minutes, 10 minutes, 20 minutes

 Open SNMP Managing the equipment if opening SNMP.

 SNMP Trap address: network management system address

 SNMP Read Community：

 SNMP Write Community：

 SNMP Trap Community：

 Port configuration

Mainly includes the following Settings(the following figure)

Picture 5-10 System information（Part of the ports）

20

Jumbo frames： Allowing super-long frames or not.

 Link: link-state of switch port be displayed

 Mode: Port working mode configuration. There are seven options “Auto Speed”、“10Half”、“10Full”、

“100Half”、“100Full”“1000Full”、“Disable”

 flow control :make flow control function. Mark “√” In the select box to start using flow control functions,

select box shows blank to indicate stopping the flow control function.

Discarding frames whether or not when in congestion setting package processing.

Start 802.3az standard: open the energy saving mode

 VLAN configuration

VLAN configuration 802.1 Q VLANs configuration. Basic knowledge about VLAN refer to section 4.3

 802.1Q VLANS Configuration

Switches in different work mode setting is different. In 802.1 Q mode, mainly including senior 802.1 Q

VLAN configuration and PVID configuration(as following figure)

Picture 5-11 802.1 Q mode

 Group of VLAN list: existing group of VLAN list

 Modification: modifying existing group of VLAN ;Into the senior VLAN configuration.

 Deletion: delete the existing group of VLAN

Page is loading ...

Binatone SW-GE1008F User manual

Binatone SW-GE1008F User manual

Other documents