INSTRUCTION MANUAL
HW-17, HW-17R, & HW-17F
TIG WELDING TORCHES
Covering the Hard Body, Silicone Rubber Body, and Flexible Head Models
F-9685-AE
December, 2004
2
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and accompanying
labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided.
This equipment must be checked periodically. Malfunctioning equipment should not be used. Parts that are broken,
missing, worn, distorted or contaminated should be replaced immediately. Should such repair or replacement become
necessary, the manufacturer recommends that a telephone or written request for service advice be made to the
Authorized Distributor from whom purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The
user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty
maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility
designated by the manufacturer.
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of
operation and safe practices for arc welding equipment, we urge you to read our booklet, "Precautions and
Safe Practices for Arc Welding, Cutting, and Gouging", Form 52-529. Do NOT permit untrained persons to
install, operate, or maintain this equipment. Do NOT attempt to install or operate this equipment until you
have read and fully understand these instructions. If you do not fully understand these instructions,
contact your supplier for further information. Be sure to read the Safety Precautions (Section 1) before
installing or operating this equipment.
Be sure this information reaches the operator.
You can get extra copies through your supplier.
3
TABLE OF CONTENTS
SECTION TITLE PAGE
SAFETY PRECAUTIONS ............................................................................... 5-10
SECTION 1 DESCRIPTION....................................................................................................11
1.1 General ...............................................................................................................11
1.2 Torch Dimensions................................................................................................11
1.3 Required Accessories / Services.........................................................................11
1.4 Electrodes ...........................................................................................................11
1.5 Collets .................................................................................................................11
1.6 Cups .................................................................................................................. 12
1.7 Optional Accessories.......................................................................................... 12
SECTION 2 INSTALLATION.................................................................................................. 15
2.1 Setup and Installation ......................................................................................... 15
2.2 Operating Instructions ........................................................................................ 16
2.3 Installation of Argon Shutoff Valves ..................................................................... 16
SECTION 3 MAINTENANCE ................................................................................................. 17
3.1 Maintenance....................................................................................................... 17
3.2 Replacement of Gas Lens Screen ...................................................................... 18
SECTION 4 REPLACEMENT PARTS ................................................................................... 19
4.1 Replacement Parts ............................................................................................. 19
4.2 Ordering............................................................................................................. 19
4
TABLE OF CONTENTS
5
WARNING: These Safety Precautions are for
your protection. They summarize precautionary
information from the references listed in Addi-
tional Safety Information section. Before per-
forming any installation or operating procedures,
be sure to read and follow the safety precautions listed below
as well as all other manuals, material safety data sheets,
labels, etc. Failure to observe Safety Precautions can result
in injury or death.
PROTECT YOURSELF AND OTHERS -
-
Some welding, cutting, and gouging
processes are noisy and require ear
protection. The arc, like the sun, emits
ultraviolet (UV) and other radiation and
can injure skin and eyes. Hot metal can cause burns.
Training in the proper use of the processes and equip-
ment is essential to prevent accidents. Therefore:
1. Always wear safety glasses with side shields in any work
area, even if welding helmets, face shields, and goggles
are also required.
2. Use a face shield fitted with the correct filter and cover
plates to protect your eyes, face, neck, and ears from
sparks and rays of the arc when operating or observing
operations. Warn bystanders not to watch the arc and not
to expose themselves to the rays of the electric-arc or hot
metal.
3. Wear flameproof gauntlet type gloves, heavy long-sleeve
shirt, cuffless trousers, high-topped shoes, and a welding
helmet or cap for hair protection, to protect against arc rays
and hot sparks or hot metal. A flameproof apron may also
be desirable as protection against radiated heat and sparks.
4. Hot sparks or metal can lodge in rolled up sleeves, trouser
cuffs, or pockets. Sleeves and collars should be kept
buttoned, and open pockets eliminated from the front of
clothing
5. Protect other personnel from arc rays and hot sparks with
a suitable non-flammable partition or curtains.
6. Use goggles over safety glasses when chipping slag or
grinding. Chipped slag may be hot and can fly far. Bystand-
ers should also wear goggles over safety glasses.
FIRES AND EXPLOSIONS -- Heat from
flames and arcs can start fires. Hot slag
or sparks can also cause fires and ex-
plosions. Therefore:
1. Remove all combustible materi-
als well away from the work area or cover the materials
with a protective non-flammable covering. Combustible
materials include wood, cloth, sawdust, liquid and gas
fuels, solvents, paints and coatings, paper, etc.
2. Hot sparks or hot metal can fall through cracks or crevices
in floors or wall openings and cause a hidden smoldering
fire or fires on the floor below. Make certain that such
openings are protected from hot sparks and metal.“
3. Do not weld, cut or perform other hot work until the
workpiece has been completely cleaned so that there are
no substances on the workpiece which might produce
flammable or toxic vapors. Do not do hot work on closed
containers. They may explode.
4. Have fire extinguishing equipment handy for instant use,
such as a garden hose, water pail, sand bucket, or
portable fire extinguisher. Be sure you are trained in its
use.
11/95
5. Do not use equipment beyond its ratings. For example,
overloaded welding cable can overheat and create a fire
hazard.
6. After completing operations, inspect the work area to make
certain there are no hot sparks or hot metal which could
cause a later fire. Use fire watchers when necessary.
7. For additional information, refer to NFPA Standard 51B,
"Fire Prevention in Use of Cutting and Welding Processes",
available from the National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269.
ELECTRICAL SHOCK -- Contact with live
electrical parts and ground can cause se-
vere injury or death. DO NOT use AC weld-
ing current in damp areas, if movement is
confined, or if there is danger of falling.
1. Be sure the power source frame (chassis) is connected to
the ground system of the input power.
2. Connect the workpiece to a good electrical ground.
3. Connect the work cable to the workpiece. A poor or
missing connection can expose you or others to a fatal
shock.
4. Use well-maintained equipment. Replace worn or dam-
aged cables.
5. Keep everything dry, including clothing, work area, cables,
torch/electrode holder, and power source.
6. Make sure that all parts of your body are insulated from
work and from ground.
7. Do not stand directly on metal or the earth while working in
tight quarters or a damp area; stand on dry boards or an
insulating platform and wear rubber-soled shoes.
8. Put on dry, hole-free gloves before turning on the power.
9. Turn off the power before removing your gloves.
10. Refer to ANSI/ASC Standard Z49.1 (listed on next page)
for specific grounding recommendations. Do not mistake
the work lead for a ground cable.
ELECTRIC AND MAGNETIC FIELDS — May
be dangerous. Electric current flowing
through any conductor causes localized
Electric and Magnetic Fields (EMF). Weld-
ing and cutting current creates EMF around
welding cables and welding machines.
Therefore:
1. Welders having pacemakers should consult their physician
before welding. EMF may interfere with some pacemakers.
2. Exposure to EMF may have other health effects which are
unknown.
3. Welders should use the following procedures to minimize
exposure to EMF:
A. Route the electrode and work cables together. Secure
them with tape when possible.
B. Never coil the torch or work cable around your body.
C. Do not place your body between the torch and work
cables. Route cables on the same side of your body.
D. Connect the work cable to the workpiece as close as
possible to the area being welded.
E. Keep welding power source and cables as far away from
your body as possible.
SAFETY PRECAUTIONS
6
FUMES AND GASES -- Fumes and
gases, can cause discomfort or harm,
particularly in confined spaces. Do
not breathe fumes and gases. Shield-
ing gases can cause asphyxiation.
Therefore:
1. Always provide adequate ventilation in the work area by
natural or mechanical means. Do not weld, cut, or gouge
on materials such as galvanized steel, stainless steel,
copper, zinc, lead, beryllium, or cadmium unless positive
mechanical ventilation is provided. Do not breathe fumes
from these materials.
2. Do not operate near degreasing and spraying operations.
The heat or arc rays can react with chlorinated hydrocar-
bon vapors to form phosgene, a highly toxic gas, and other
irritant gases.
3. If you develop momentary eye, nose, or throat irritation
while operating, this is an indication that ventilation is not
adequate. Stop work and take necessary steps to improve
ventilation in the work area. Do not continue to operate if
physical discomfort persists.
4. Refer to ANSI/ASC Standard Z49.1 (see listing below) for
specific ventilation recommendations.
CYLINDER HANDLING -- Cylinders, if
mishandled, can rupture and violently
release gas. Sudden rupture of cylin-
der, valve, or relief device can injure
or kill. Therefore:
1. Use the proper gas for the process and use the proper
pressure reducing regulator designed to operate from the
compressed gas cylinder. Do not use adaptors. Maintain
hoses and fittings in good condition. Follow manufacturer's
operating instructions for mounting regulator to a com-
pressed gas cylinder.
2. Always secure cylinders in an upright position by chain or
strap to suitable hand trucks, undercarriages, benches,
walls, post, or racks. Never secure cylinders to work
tables or fixtures where they may become part of an
electrical circuit.
3. When not in use, keep cylinder valves closed. Have valve
protection cap in place if regulator is not connected.
Secure and move cylinders by using suitable hand trucks.
Avoid rough handling of cylinders.
4. Locate cylinders away from heat, sparks, and flames.
Never strike an arc on a cylinder.
5. For additional information, refer to CGA Standard P-1,
"Precautions for Safe Handling of Compressed Gases in
Cylinders", which is available from Compressed Gas
Association, 1235 Jefferson Davis Highway, Arlington,
VA 22202.
EQUIPMENT MAINTENANCE -- Faulty or im-
properly maintained equipment can cause
injury or death. Therefore:
1. Always have qualified personnel perform the installation,
troubleshooting, and maintenance work. Do not perform
any electrical work unless you are qualified to perform
such work.
Used to call attention to immediate haz-
ards which, if not avoided, will result in
immediate, serious personal injury or loss
of life.
Used to call attention to potential hazards
which could result in personal injury or
loss of life.
Used to call attention to hazards which
could result in minor personal injury.
2. Before performing any maintenance work inside a power
source, disconnect the power source from the incoming
electrical power.
3. Maintain cables, grounding wire, connections, power cord,
and power supply in safe working order. Do not operate any
equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep equip-
ment away from heat sources such as furnaces, wet condi-
tions such as water puddles, oil or grease, corrosive atmo-
spheres and inclement weather.
5. Keep all safety devices and cabinet covers in position and
in good repair.
6. Use equipment only for its intended purpose. Do not modify
it in any manner.
ADDITIONAL SAFETY INFORMATION -- For
more information on safe practices for elec-
tric arc welding and cutting equipment, ask
your supplier for a copy of "Precautions and
Safe Practices for Arc Welding, Cutting and
Gouging", Form 52-529.
The following publications, which are available from the Ameri-
can Welding Society, 550 N.W. LeJuene Road, Miami, FL
33126, are recommended to you:
1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"
2. AWS C5.1 - "Recommended Practices for Plasma Arc
Welding"
3. AWS C5.2 - "Recommended Practices for Plasma Arc
Cutting"
4. AWS C5.3 - "Recommended Practices for Air Carbon Arc
Gouging and Cutting"
5. AWS C5.5 - "Recommended Practices for Gas Tungsten
Arc Welding“
6. AWS C5.6 - "Recommended Practices for Gas Metal Arc
Welding"“
7. AWS SP - "Safe Practices" - Reprint, Welding Handbook.
8. ANSI/AWS F4.1, "Recommended Safe Practices for Weld-
ing and Cutting of Containers That Have Held Hazardous
Substances."
This symbol appearing throughout this manual
means Attention! Be Alert! Your safety is in-
volved.
The following definitions apply to DANGER, WARNING,
CAUTION found throughout this manual:
SAFETY PRECAUTIONS
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
11
1.1 General
Each Torch in the HW-17 family is rated at 130 A (ACHF or DCSP)
continous duty and 150 A at 50% duty cycle (using standard collet bodies).
The hard body on the HW-17 provides the best heat and abrasion resistance.
The HW-17R has a Silicone rubber body which provides good, high
frequency resistance. For reaching hard-to-get-at applications, the HW-
17F uses a flexible head. All the torches are air-cooled.
1.2 Torch Dimensions
Length, approx ........................... 8-1/8 in. (206 mm)
Handle diameter .............................. 3/4 in. (19 mm)
Height of torch head:
with short cap .................... 3-13/16 in. (97 mm)
with long cap ...................... 7-7/16 in. (189 mm)
1.3 Required Accessories/Services
A. Collet, collet body, electrode, and cup. See below.
B. Shielding gas regulator/flowmeter (if cylinder gas is used) OR
flowmeter (if gas is piped).
C. Gas hose, 12-1/2-ft long (40V77) or 25-ft long (34V38) connects
between regulator/flowmeter and Torch cable and hose assembly.
D. Welding power source and shielding gas supply.
E. Power Cable Adaptor (105Z57) for connecting Torch power cable
to power source and gas supply.
1.4 Electrodes
Each Torch model uses .020-inch thru 1/8-inch diameter electrodes.
The 3-inch and 7-inch long standard Torch cap is designed for 7-inch
electrodes. A short cap for the 3-inch electrode is available as an optional
accessory. See Table 1-1.
1.5 Collets
Collets are available for each of the five electrode sizes. The collet
bodies come in both standard and gas lens styles. A large diameter gas
lens is available for 3/32-inch and 1/8-inch electrodes. See Table 1-2.
SECTION 1 DESCRIPTION
12
SECTION 1 DESCRIPTION
1.6 Cups
Cups are available for use with standard collet bodies: Standard
ceramic in all sizes, long ceramic in sizes in sizes 4 thru 7. High-impact
ceramic, either plain, in all sizes, or sleeved, in sizes 4 thru 10. See Table
1-3.
Cups are also available for use with gas lens collet bodies: Standard
or high-impact ceramic in sizes 4 thru 8. Sizes 10 and 12 high-impact
ceramic are available for use with large diameter gas lens. See Table 1-3.
1.7 Optional Accessories
A. Short Cap (57Y04) for use with 3-in. electrodes.
B. Argon Valve (17732) replaces handle on phenolic body HW-17s
(16X48, 16X50, and 634720) and provides on-off control of gas flow
at Torch. (See Section 2 for installation instructions.)
C. Braided nylon sheath to protect service lines - P/N 2075198 (9-ft
long) and P/N 2075200 (20-ft long).
D. Tig Accessory Kit (999126) includes three collets, three collet
bodies, three 7-in. long 2% thoriated electrodes (each in 1/16-in.,
3/32-in., and 1/8-in. sizes), three high impact cups (Nos. 5, 6, and
8), and one short torch cap.
13
Table 1-1. Electrode and Cup Sizes for Different Welding Currents
Welding Currents (Amps)
Electrode
Diameter
(Inches)
High-
Impact Cup
No.
Ceramic Cup
No.
ACHF* DCSP** DCRP**
Using pure tungsten
electrodes
Using thoriated
electrodes ***
Using pure orthoriated
tungsten electrodes
5-15
10-60
50-100
100-150
5-20
60-80
70-150
---
5-20
15-80
70-150
---
---
---
10-20
15-30
.020
.040
1/16
3/32
or
1/8
4
4-5
4-5-6
5-6-7-8
4-5
4-5
4-5-6
6-7-8
* Based on use of unbalanced wave transformer. If using balanced wave transformer, reduce maximum values by about 30 % or use
the next larger size electrode.
** Thoriated tungsten electrodes are recommended when gas lens and high frequency starting are used.
*** Balled electrode tip ends can best be formed and maintained at these ac current levels.
Table 1-2. Collets and Collet Bodies
Electrode Size
Collet
Standard
Collet Body
Gas Lens Collet
Body*
Large Dia.Gas
LensCollet Body**
in. mm
0.020 0.5 10N21 10N29 45V29 ---
0.040 1.0 10N22 10N30 45V24 ---
1/16 1.6 10N23 10N31 45V25 ---
3/32 2.4 10N24 10N32 45V26 45V64
1/8 3.2 10N25 10N28 45V27 995795
5/32 4.0 54N20 406488*** 45V28 45V63
* Collet body insulator (P/N 54N01) is required when using gas lens collet bodies.
** Collet body insulator (P/N 54N63) is required when using large diameter gas lens collet bodies.
*** Use of a gas lens collet body is recommended for this size.
Table 1-3. Gas Cups
Cup No. 4 5 6 7 8 10 12 Short*
High-Impact Cup
10N50 10N49 10N48 10N47 10N46 10N45 10N44 ---
Sleeved High-Impact Cup
10N56 10N55 10N54 10N53 10N52 10N51 --- ---
Ceramic Cup
105Z43 105Z42 105Z44 105Z45 08N78 08N79 08N80 ---
Long Ceramic Cup
12N03 105Z60 12N02 105Z61 --- --- --- ---
Gas Lens High-Impact Cup
54N18 54N17 54N16 54N15 54N14 --- --- 54N19
Large Dia. Gas Lens High-impact Cup
--- --- --- --- --- 53N88 53N87 53N89
Gas Lens Ceramic Cup
54N35 54N34 54N33 54N32 54N31 --- --- 54N36
SECTION 1 DESCRIPTION
Page is loading ...
15
2.1 Setup and Installation
A. Connect the regulator/flowmeter to a gas cylinder. Refer to the
instructions supplied with the regulator/flowmeter for details on
attaching and adjusting the regulator.
B. Connect one end of the gas hose (40V77 or 34V38) to the regulator
outlet and the other end to the torch cable adaptor (105Z57).
C. Connect the power cable adaptor to the welding power source,
either directly or through a suitable length of welding cable fitted with
lugs.
D. Install collet body, collet, electrode, and cup on torch (see Figure
2-1) as follows:
1. Screw in collet body. (If using a gas lens, assemble insulator
on collet body before installing.)
2. Apply a thin coat of silicone grease to the surface of the cup that
mates with the torch body and then screw on cup.
3. Remove torch cap and slide collet into position (tapered end
first).
4. Slip electrode down through hole in top of collet until end of
electrode extends beyond rim of cup. (Exact extension varies
from 1/8 inch for butt welding with standard collet bodies to
3/4 inch or more for corner or fillet welds with gas lens collet
bodies and cups).
5. Screw on the torch cap and tighten. The cap will press down
on the collet to grip the electrode securely. To readjust
electrode, loosen torch cap.
SECTION 2 INSTALLATION
NOTE
When using high frequency with
sleeved high- impact cups, arcing
may sometimes occur between
the electrode and the steel sleeve.
To avoid this, it is advantageous
to extend the electrode as far as
possible consistent with the par-
ticular application.
"O" RING
TORCH CAP
ELECTRODE
ELECTRODE
COLLET
TORCH BODY
COLLET BODY
CUP
GAS LENS
CUP
GAS LENS
COLLET
BODY
GAS LENS
INSULATOR
Figure 2-1. Exploded View of HW-17 Torch
16
2.2 Operating Instructions
A. Make sure that all gas connections in the system and the torch cap
have been securely tightened.
B. With the regulator flow-adjusting valve closed, open the gas
cylinder or station valve.
C. Set the power source for the desired welding current.
D. Open all shielding gas valves downstream from the flowmeter or
flowmeter/regulator (e.g., valve on torch, lever-operated shutoff
valve, or solenoid-operated valve in power source).
E. Set shielding gas flow to the desired level, as registered on
flowmeter tube or gauge.
NOTE
Purge the gas hose by allowing the
gas to flow long enough (up to 15
minutes on new torch; less than 5
minutes thereafter) to drive out air
and moisture. This will help prevent
weld contamination.
2.3 Installation of Argon Shutoff Valve
Referring to Figure 2-2, install argon shutoff valve (17732) on HW-17
phenolic body torch originally supplied without valve (16X48, 16X50, or
634720) as follows:
A. Remove and discard the torch handle (105Z55).
B. Remove the power cable from the torch body.
C. Screw the front handle (12N06) of the argon valve to the torch body.
D. Remove the rear handle (17731) from the argon valve.
E. Assemble valve body (17729) to torch body.
F. Pass the power cable through the rear handle and attach it to the
valve body (17729).
G. Screw the rear handle to the valve body.
SECTION 2 INSTALLATION
17
Figure 2-2. Argon Shutoff Valve Assembly (P/N 17732)
FLEX SUPPORT - 19191
(634705, 634706, & 601152)
VALVE BODY - 17729
"O" RING - 85W10 (1/4" I.D.)
HW-17 TORCH
FRONT HANDLE - 12N06
REAR HANDLE - 17731
(2) "O" RING - 86W04
(5/16" I.D.)
VALVE SLEEVE -
17730
3.1 Maintenance
A. A poor shielding gas connection, or a leaky hose, will not only waste
gas but permit the entry of minute amounts of air, sufficient to
contaminate both the electrode and the weld. Trouble signs: a
bluish cast on the electrode after it has cooled; in welding aluminum,
a dark gray deposit on or beside the weld bead.
B. Keep the torch hose away from hot metal.
C. Do not try to repair concentric power cable, it should be replaced.
Two piece cable and hose assemblies may be repaired using the
repair kits noted in parts breakdown. The kits include replacement
fittings and lugs for the cable and hose.
D. If an electrode becomes contaminated, shut off power, then remove
electrode from torch. Break off the contaminated end (nicking with
a grinding wheel first will help) and replace electrode.
E. Periodically check on the sealing "O" ring on the torch cap. If it
shows signs of wear or distortion, cut it off. Then install new "O" ring
(181W53) using the assembly tool (13N42) supplied with the torch.
Apply a small amount of silicone grease to the new "O" ring before
attempting to slide it over the tool and into the cap groove.
SECTION 3 MAINTENANCE
If this equipment does not operate prop-
erly, stop work immediately and investi-
gate the cause of the malfunction. main-
tenance work must be performed by an
experienced person and electrical work
by a trained electrician. do not permit
untrained persons to inspect, clean, or
repair this equipment. use only recom-
mended replacement parts.
18
3.2 Replacement of Gas Lens Screens (See Figure 3-1)
If screens are plugged by spatter, replace as follows:
A. With the collet body removed from the torch, remove the outer snap-
ring (54N71). This can be done by using a small screwdriver, or an
electrode with a diameter no greater than 3/32". Insert the tip in the
slot on the outer sleeve of the collet body, and pry out the snapring.
B. Using a pair of needle nose pliers, pry out the inner snapring
(54N69).
SECTION 3 MAINTENANCE
Figure 3-1. Replaceable Parts in Collet Bodies 45V63, 995795,
and 45V64
C. Hold the collet body with the screens down, and gently tap the body
on the work bench. The body contains three fine and one coarse
screens, separated by spacers. If the screens are not badly fouled,
they should drop out of the body. Excessive fouling may necessi-
tate prying out the screens.
D. Inspect the screens and replace those which show plugging or other
damage.
E. Replace the screens and spacers making sure that a spacer is
installed between each screen, and that the coarsest screen is
inserted last. Replace the snaprings.
SCREEN (250 mesh)
54N66
SCREEN (100 mesh)
54N67
INNER SPACER
54N68
INNER SNAPRING
54N69
OUTER SNAPRING
54N71
OUTER SPACER
54N70
19
SECTION 4 REPLACEMENT PARTS
4.1 REPLACEMENT PARTS
The following illustrations of the HW-17, HW-17R, and HW-17F
Torch identify each replacement part by item number as tabulated in the
related parts list. The list identifies each part by part number, descrip-
tion, and quantity used.
4.2 ORDERING
To assure proper operation, it is recommended that only genuine
ESAB parts and products be used with this equipment. The use of non-
ESAB parts may void your warranty.
Replacement parts may be ordered from your ESAB distributor or from:
ESAB Welding & Cutting Products
Attn: Customer Service Dept.
P.O. Box 100545
Florence, SC 29501-0545
A. Give the part number, description and quantity of each part
required.
B. Give part number and description of equipment on which the parts
are to be used.
C. Indicate any special shipping instructions.
For technical assistance directly from an ESAB service representative, call
(843)664-4416 or 5550. Additionally, ESAB offers a toll free facsimile (FAX)
service via 1-800-446-5693.
20
Table 4-1. HW-17 Hard Body Assemblies
9
10
6
5
8
7
LD Gas Lens Access.
(See Tables 1-2, 1-3)
Gas Lens Access.
(See Tables 1-2, 1-3)
Standard Access.
(See Tables 1-2, 1-3)
1
2
3
4
NOTE: Torch part nos. 634705, 634706, and 601152
incorporate an argon shutoff valve assembly in place of handle
(105Z55). The valve assembly is illustrated in Figure 2-2.
3/8" - 24
Figure 4-1. HW-17 Hard Body Torch Components
HW-17, 60 deg., 12-1/2 ft. 16X48 HW-17V, 60 deg., 12-1/2 ft. 16X48LV
HW-17, 60 deg., 25 ft. 16X50 HW-17V, 60 deg., 25 ft. 16X50LV
HW-17, 90 deg., 25 ft. 634720 HW-17-2, 60 deg., (2) pc cable, 12-1/2 ft. 33855
HW-17V (slide), 60 deg., 12-1/2 ft. 634705 HW-17-2, 60 deg., (2) pc cable, 25 ft. 33856
HW-17V (slide), 60 deg., 25 ft. 634706 HW-17V-2, 60 deg., (2) pc cable, 12-1/2 ft. 33813
HW-17V (slide), 90 deg., 12-1/2 ft. 601152 HW-17V-2, 60 deg., (2) pc cable, 25 ft. 33814
HW-17-2-TL, 60 deg., 2 pc cable,
w/Twist-Lock Conn., 12 1/2 ft.
35782 HW-17V-2-TL, 60 deg. (2) pc cable w/Twist-Lock
Conn., 12 1/2 ft.
35857
3/8" - 24
5/8" - 24
*Optional PVC Power Cable 57Y01 (12 1/2'); 57Y03 (25')
ITE M
NO.
QTY
REQ.
PART
NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
105Z55
997022*
997023*
33946
33947
35873
34651
105Z57
54N01
54N63
601477
57Y04
57Y02
57Y06
57Y06LV
HANDLE
POWER CABLE RUBBER (12-1/2 FT.)
POWER CABLE RUBBER (25 FT.)
2-PC CABLE & HOSE ASSY. (12-1/2 FT.)
2-PC CABLE & HOSE ASSY. (25 FT.)
2-PC CABLE & HOSE ASSY. w/TWIST-LOCK CONN. (12 1/2 FT.)
REPAIR KIT
POWER CABLE ADAPTER
GAS LENS INSULATOR
LD. GAS LENS INSULATOR
BODY, 90 DEG.
CAP, SHORT (includes "O" ring 98W18)
CAP, LONG (includes "O" ring 98W18)
BODY, 60 DEG.
BODY W/ ROTARY VALVE (includes valve stem 19621)
11 1 19621 VALVE STEM (includes o-ring 598869)
11
21
Table 4-2. HW-17R Silicone Rubber Assemblies
Standard Access.
(See Tables 4-3, 4-5)
Lg. Dia. Gas Lens Access.
(See Tables 4-3, 4-5)
8
9
10
7
6
11
12
1
5
4
Figure 4-2. HW-17R Silicone Rubber Torch Components
HW-17R, 60 deg., 12-1/2 ft 16X48R
HW-17R, 60 deg., 25 ft 16X50R
HW-17RV, 60 deg., 12-1/2 ft 634705R
HW-17RV, 60 deg., 25 ft 634706R
HW-17RV, 90 deg., 25 ft 601152R
HW-17RV, 60 deg., (2) pc cable, 12-1/2 ft 33813R
HW-17RV, 60 deg., (2) pc cable, 25 ft 33814R
Gas Lens Access.
(See Tables 4-3, 4-5)
2
3/8" - 24
3
3/8" - 24
5/8" - 24
ITEM
NO.
QTY
REQ.
PART
NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
19576R
19621
997022*
997023*
33946
33947
34651
105Z55
105Z57
54N63
54N01
19626
601477R
57Y04
57Y02
57Y06R
BODY, 60 DEG., W/ VALVE (includes valve stem 19621)
VALVE STEM (includes "O' ring 598869)
POWER CABLE RUBBER (12-1/2 FT)
POWER CABLE RUBBER (25 FT)
TWO PIECE CABLE & HOSE ASSY. (12-1/2 FT)
TWO PIECE CABLE & HOSE ASSY. (25 FT)
REPAIR KIT
HANDLE
POWER CABLE ADAPTER
LD. GAS LENS INSULATOR
GAS LENS INSULATOR
GASKET
BODY, 90 DEG., W/ VALVE
CAP, SHORT (includes "O" ring 98W18)
CAP, LONG (includes "O" ring 98W18)
BODY, 60 DEG.
*Optional PVC Power Cable 57Y01 (12 1/2'); 57Y03 (25')
(uses short cap 57Y04)
22
4
3
2
11
10
9
8
7
6
5
Lg. Dia. Gas Lens
Access. (See Tables 4-1, 4-2)
Standard Access.
(See Tables 4-2, 4-2)
Gas Lens Access.
(See Tables 4-1, 4-2)
HW-17F, 12-1/2 ft 19881
HW-17FV, 12-1/2 ft 19882
HW-17F, 25 ft 19883
HW-17FV, 25 ft 19884
HW-17FV-2, (2) pc cable, 12-1/2 ft 33815
HW-17FV-2, (2) pc cable, 25 ft 33816
Table 4-3. HW-17F Flexible Head Assemblies
Figure 4-3. HW-17F Flexible Head Torch Components
1
12
*Optional PVC Power Cable 57Y01 (12 1/2'); 57Y03 (25')
ITEM
NO.
QTY
REQ.
PART
NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
105Z55
997022*
997023*
33946
33947
34651
105Z57
54N63
54N01
19626
19885
57Y04
57Y02
19886
19621
HANDLE
POWER CABLE RUBBER (12-1/2 FT.)
POWER CABLE RUBBER (25 FT.)
2-PC CABLE & HOSE ASSY. (12-1/2 FT.)
2-PC CABLE & HOSE ASSY. (25 FT.)
REPAIR KIT FOR TWO PIECE CABLE & HOSE ASSY.
POWER CABLE ADAPTER
LD. GAS LENS INSULATOR
GAS LENS INSULATOR
GASKET
BODY ASSY.
CAP, SHORT (includes "O" ring 98W18)
CAP, LONG (includes "O" ring 98W18)
BODY ASSY. W/ VALVE (includes valve stem 19621)
VALVE STEM (includes "O" ring 598869)
3/8" - 24
3/8" - 24
5/8" - 24
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
27
REVISION HISTORY
1. Revision "AC" of 09/2003 added note "uses short cap 57Y04" to Table 4-2, P/N 601152R. Various editorial
changes and format modifications have also been incorporated.
2. Revision "AD" of 02/2004 updated Replacement Parts pages to correctly identify valve assembly and associated
o-ring.
3. Added insert in back of manual from scan of document F15-159 - 12 / 2004.
F-9685-AE 12 / 2004
IF YOU DO NOT KNOW WHOM TO CALL
Telephone: (800) ESAB-123
Fax: (843) 664-4452
Hours: 7:30 AM to 5:00 PM EST
or
visit us on the web at http://www.esabna.com
The ESAB web site offers
Comprehensive Product Information
Material Safety Data Sheets
Warranty Registration
Instruction Literature Download Library
Distributor Locator
Global Company Information
Press Releases
Customer Feedback & Support
A. CUSTOMER SERVICE QUESTIONS:
Telephone: (800)362-7080 / Fax: (800) 634-7548 Hours: 8:00 AM to 7:00 PM EST
Order Entry Product Availability Pricing Order Information Returns
B. ENGINEERING SERVICE:
Telephone: (843) 664-4416 / Fax : (800) 446-5693 Hours: 7:30 AM to 5:00 PM EST
Warranty Returns Authorized Repair Stations Welding Equipment Troubleshooting
C. TECHNICAL SERVICE:
Telephone: (800) ESAB-123/ Fax: (843) 664-4452 Hours: 8:00
AM to 5:00 PM EST
Part Numbers Technical Applications Specifications Equipment Recommendations
D. LITERATURE REQUESTS:
Telephone: (843) 664-5562 / Fax: (843) 664-5548 Hours: 7:30 AM to 4:00 PM EST
E. WELDING EQUIPMENT REPAIRS:
Telephone: (843) 664-4487 / Fax: (843) 664-5557 Hours: 7:30 AM to 3:30 PM EST
Repair Estimates Repair Status
F. WELDING EQUIPMENT TRAINING
Telephone: (843)664-4428 / Fax: (843) 679-5864 Hours: 7:30 AM to 4:00 PM EST
Training School Information and Registrations
G. WELDING PROCESS ASSISTANCE:
Telephone: (800) ESAB-123 Hours: 7:30 AM to 4:00 PM EST
H. TECHNICAL ASST. CONSUMABLES:
Telephone : (800) 933-7070 Hours: 7:30 AM to 5:00 PM EST
ESAB Welding & Cutting Products, Florence, SC Welding Equipment
COMMUNICATION GUIDE - CUSTOMER SERVICES
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: ESAB HW-17R Manuel utilisateur
- español: ESAB HW-17R Manual de usuario
Related papers
-
ESAB m3 plasma Precision Plasmarc Plasma Gas Box & Shield Gas Box User manual
-
-
ESAB MultiPower 460 Pulse DC Welding Power Source User manual
-
-
