LG SK6 User manual

Category
Soundbar speakers
Type
User manual
Please read this manual carefully before operating your set and retain it for
future reference.
OWNER’S MANUAL
LG Wi-Fi
Sound Bar
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
MODEL
SK6 (SK6, SPK5-W)
1 Getting Started
Getting Started2
Getting Started
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufcient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, should be placed on the
apparatus.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: No naked ame sources, such as lighted
candles, should be placed on the apparatus.
NOTICE: For safety marking information including
product identication and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
Check the specication page of this owner’s manual
to be certain of the current requirements.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result
in electric shock or re. Periodically examinew the
cord of your device, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of
the device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
CAUTION: Only use the AC adapter supplied with
this device. Do not use a power supply from another
device or another manufacturer. Using any other
power cable or power supply may cause damage to
the device and void your warranty.
Getting Started 3
Getting Started
1
This device is equipped with a portable battery or
accumulator.
How to Safely remove the batteries or the
battery pack from the equipment: To Remove the
old batteries or battery pack, follow the assembly
steps in reverse order. To prevent contamination of
the environment and bring on possible threat to
human and/or animal health, the old batteries or the
battery pack must be put in an appropriate container
at designated collection points. Do not dispose
of batteries or battery pack together with other
waste. It is recommended that you use local, free
reimbursement systems batteries or battery packs,
(may not be available in your area). The batteries or
the battery pack should not be exposed to excessive
heat such as sunshine, re or the like.
Symbols
~
Refers to alternating current (AC).
0
Refers to direct current (DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
Table of Contents4
2 Connecting
13 Organizing cables
13 Connecting the AC Adapter
13 Wireless subwoofer connection
15 Connecting to your TV
15 Using an OPTICAL cable
15 LG Sound Sync
17 Using an HDMI cable
17 ARC (Audio Return Channel) function
17 What is SIMPLINK?
18 Additional information for HDMI
19 Optional equipment connection
19 HDMI connection
19 OPTICAL IN connection
20 PORTABLE IN connection
21 Network connection
21 Wired connection
22 Wireless connection
23 “LG Wi-Fi Speaker”
23 Installing “LG Wi-Fi Speaker” App
23 Works with the Google Assistant
Table of Contents
1 Getting Started
2 Safety Information
6 Main Features
6 Introduction
7 Remote control
8 Front panel
9 Rear panel
11 Installing the sound bar
11 Mounting the main unit on a wall
Table of Contents 5
1
2
3
4
5
Some of the content in this manual may differ from “LG Wi-Fi Speaker” app depending on the applications
version.
3 Operating
24 Using a Bluetooth Wireless Technology
24 About Bluetooth
24 Bluetooth profiles
24 Listening to Music of a Bluetooth Device
26 Bluetooth connection lock (BT LOCK)
26 Other operations
26 Using your TV remote control
27 AV Sync
27 Turn off the sound temporarily
27 Auto display Dimmer
27 Displaying input source information
27 Auto power down
28 AUTO POWER On/Off
29 Auto function change
30 Sound adjustment
30 Setting sound effect
30 Adjust volume level automatically
30 Adjust Sound level
31 Standby mode
31 Standby mode
31 Network standby mode
31 Bluetooth standby mode
31 Reset the Speaker
4 Troubleshooting
32 Troubleshooting
32 General
33 Network
34 Application
34 NOTES to use wireless
35 NOTES to release Demo mode
5 Appendix
36 File requirement
36 Trademarks and licenses
37 Specifications
39 Handling the Speaker
39 Important Information Relating to Network
Services
40 TERMS OF USE
Getting Started6
Getting Started
1
Main Features
LG Sound Sync
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
“LG Wi-Fi Speaker” application
Listens to music stored on your smart device.
You can control this speaker with your iPod touch/
iPhone or Android device via “LG Wi-Fi Speaker”
app. This speaker and your smart device must be
connected to the same network. Visit Apple “App
Store” or Google “Play Store” to search for “LG Wi-Fi
Speaker” app. For detailed information, refer to page
23.
y
Depending on the applications version and the
software of smart device, “LG Wi-Fi Speaker” app
may not be operated normally.
y
Some smart devices may not be compatible with
this speaker.
Bluetooth®
Listens to music stored on your Bluetooth device.
Introduction
Symbol used in this manual
,
Note
Indicates special notes and operating features.
>
Caution
Indicates cautions for preventing possible damages
from abuse.
Getting Started 7
Getting Started
1
Remote control
Replacement of Battery
Remove the battery cover on the rear of the remote
control, and insert the battery with
4
and
5
matched correctly.
• • • • • • • • • • • • • •
a
• • • • • • • • • • • • •
1
(Standby): Switches the unit ON or OFF.
VOL (Volume)
o
/
p
: Adjusts speaker volume.
F (Function): Selects the function and the input
source.
Input source / Function Display
Wi-Fi WI-FI
Optical
ARC
LG Sound Sync (Wired)
OPT/HDMI ARC
Bluetooth BT
LG Sound Sync (Wireless) LG TV
HDMI IN HDMI
Portable PORT.
[
(Mute): Mutes the sound.
C
/
V
(Skip): Skips Fast backward or Forward.
N
(Play/Pause): Starts playback. / Pauses playback.
• • • • • • • • • • • • • •
b
• • • • • • • • • • • • •
SOUND EFFECT: Selects a sound effect mode.
: Adjusts sound level of each speaker. (Page
30)
AV SYNC:
- Synchronizes the audio and video.
- Controls TV remote. (Page 26)
J
:
- Displays the input source information.
- Displays the connected Bluetooth device name on
Bluetooth function.
AUTO VOL :
- Turns on or off the AUTO VOLUME mode.
AUTO POWER:
- Turns on or off AUTO POWER function.
(Page 28)
- Turns on or off the Bluetooth connection lock.
(Page 26)
Getting Started8
Getting Started
1
A
Remote sensor
B
LED indicator
Shows connection status.
y
White (Blinking): Waiting for network connection
on Wi-Fi function.
y
White (Staying on): Network connection is
completed on Wi-Fi function or the other
functions are selected.
y
White (Dimmed): Standby mode with network
connection.
y
Red (Staying on): Standby mode without network
connection.
C
Display window
D
1
(Standby)
Switches the unit ON or OFF.
F (Function)
Selects the function and input source. (WI-FI,
OPT/HDMI ARC, BT, LG TV, HDMI, PORT.)
p
/
o
(Volume)
(Wi-Fi)
Selects Wi-Fi function.
Front panel
Getting Started 9
Getting Started
1
A
DC IN (AC adapter input)
B
OPTICAL IN connector
Connect to an optical device.
C
PORTABLE IN connector
Connect portable device.
D
USB (Service only)
S/W download connector
E
LAN port
Connect to a router.
F
HDMI IN
Connect to device with HDMI OUT.
G
HDMI OUT (TV ARC)
Connect to HDMI IN (ARC) on TV.
Rear panel
Getting Started10
Getting Started
1
Useful functions for using the unit
Function Description To do Do this
TV Remote On/
Off
(Page 26)
It allows you to control the
volume of this unit by your TV
remote control even by other
company’s product.
Initial setting of this function
was set to on.
ON Press and hold AV SYNC on the remote
control for about 3 seconds and then press
the button again.
OFF Press and hold AV SYNC on the remote
control for about 3 seconds and then press
the button again.
BT Lock On/Off
(Page 26)
It allows you to connect a
Bluetooth device only on
Bluetooth and LG TV functions.
Initial setting of this function
was set to off.
ON Press and hold AUTO POWER on the
remote control for about 2 seconds in
Bluetooth function and then press the
button again.
OFF Press and hold AUTO POWER on the
remote control for about 2 seconds in
Bluetooth function and then press the
button again.
Auto Power
On/Off
(Page 28)
It allows the unit to turn on
and off automatically by input
signals :
Optical, LG TV, Bluetooth or “LG
Wi-Fi Speaker” app.
Initial setting of this function
was set to on.
ON Press AUTO POWER on the remote control
and then press the button again.
OFF Press AUTO POWER on the remote control
and then press the button again.
BT Standby
On/Off
(Page 31)
It allows the unit to switch
to standby mode while
maintaining Bluetooth
connection.
ON Set the volume to a minimum in advance.
Press and hold
p
on the unit and
J
on
the remote control for about 3 seconds and
then press the button again.
OFF Set the volume to a minimum in advance.
Press and hold
p
on the unit and
J
on
the remote control for about 3 seconds and
then press the button again.
Network
Standby On/
Off
(Page 31)
It allows the unit to switch
to standby mode while
maintaining a network
connection.
ON Press
1
on the unit or
1
on the remote
control.
OFF Press
1
on the unit or
1
on the remote
control for about 3 seconds.
Getting Started 11
Getting Started
1
Installing the sound bar
You can hear the sound by connecting the unit to the
other device: TV, Blu-ray disc player, DVD player, etc.
Place the unit in front of the TV and connect it to the
device you want. (Pages 15 - 21)
You can place the wireless subwoofer anywhere in
your room. But it is better to place the subwoofer
near the main unit. Turn it slightly toward the center
of the room to reduce the wall reections.
y
For best performance of wireless connection
such as Bluetooth or wireless subwoofer,
do not install the unit on Metallic furniture
because wireless connection communicates
through a module positioned on the bottom
of the unit.
y
Be careful not to make scratches on the
surface of the Unit /Subwoofer when
installing or moving them.
>
Caution
For the convenient button usage, it is
recommended to take some distance between
the soundbar and your TV when you install the
sound bar.
,
Note
Mounting the main unit
on a wall
You can mount the main unit on a wall.
Because it is difcult to make a connection after
installing this unit, you should connect the cables
before installation.
>
Caution
Preparation materials
Unit
Wall bracket install guide
Screws
Screws (A)
Wall plug
Wall bracket
(Not supplied)
Getting Started12
Getting Started
1
1. Match the TV’s BOTTOM EDGE of Wall bracket
install guide with the bottom of TV and attach to
the position.
2. When you mount it on a wall (concrete), use the
wall plugs. You should drill some holes. A guide
sheet (Wall bracket install guide) is supplied to
drill. Use the sheet to check the point to drill.
3. Remove the Wall bracket install guide.
4. Fix the brackets with screws (A) as shown in the
illustration below.
Screws (A) and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting.
,
Note
5. Put the unit on the brackets to match screw
holes on the bottom of the unit.
6. Fix the unit with the screws firmly.
To detach the unit, perform it in reverse order.
,
Note
y
Do not install this unit upside down. It can
damage the parts of this unit or be the cause
of personal injury.
y
Do not hang onto the installed unit and avoid
any impact to the unit.
y
Secure the unit rmly to the wall so that it
does not fall off. If the unit falls off, it may
result in an injury or damage to the product.
y
When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
>
Caution
2 Connecting
Connecting 13
Connecting
2
Organizing cables
You can organize the cable with cable ties.
1. Hold the cables together with cable ties as shown
below.
2. Tighten cable ties.
After all connections are completed, you can
arrange cables as needed.
,
Note
Connecting the AC
Adapter
Connect the sound bar to the power supply with the
supplied AC adapter.
1. Connect the supplied AC power cord to the AC
adapter.
2. Connect the AC adapter cable to DC IN adapter
input.
3. Plug the AC power cord into an AC outlet.
Only use the AC adapter supplied with this
device. Do not use a power supply from another
device or manufacturer. Using any other power
cable or power supply may cause damage to the
device and void your warranty.
>
Caution
Wireless subwoofer
connection
LED indicator of wireless subwoofer
LED Color Status
Green
(Blink)
The connection is trying.
Green The connection is completed.
Red The wireless subwoofer is in
standby mode or the connection
is failed.
Off (No
display)
The power cord of wireless
subwoofer is disconnected.
Setting up the wireless subwoofer for
the first time
1. Connect the power cord of the sound bar and the
wireless subwoofer to the outlet.
2. Turn on the sound bar. The sound bar and
the wireless subwoofer will be automatically
connected.
Connecting14
Connecting
2
Manually pairing wireless subwoofer
When your connection is not completed, you can
check red LED on the wireless subwoofer and the
wireless subwoofer does not make sound. To solve
the problem, follow the steps below.
1. Press Pairing button on the rear of the wireless
subwoofer.
Pairing
- The green LED on the rear of the wireless
subwoofer blinks quickly.
(If the green LED does not blink, press and hold
the Pairing button.)
2. Turn on the sound bar.
3. Pairing is completed.
- The green LED on the rear of the wireless
subwoofer turns on.
y
It takes a few seconds (and may take longer)
for the main unit and the subwoofer to
communicate with each other and make
sounds.
y
The closer the main unit and the subwoofer,
the better sound quality. It is recommended
to install the main unit and the subwoofer as
close as possible and avoid the cases below.
- There is an obstacle between the main unit
and the subwoofer.
- There is a device using same frequency
with this wireless connection such as
a medical equipment, a microwave or a
wireless LAN device.
- Keep the sound bar and the subwoofer
away from the device (ex. wireless router,
microwave oven, etc.) over 1 m to prevent
wireless interference.
!
1 m
,
Note
Connecting 15
Connecting
2
Connecting to your TV
Please connect with this unit and TV using the optical
digital cable or HDMI cable considering the state of
the TV.
Using an OPTICAL cable
1. Connect the OPTICAL IN jack on the back of the
unit to OPTICAL OUT jack on the TV using an
OPTICAL cable.
Optical cable
2. Select the input source to OPT/HDMI ARC
by pressing F button on the remote or unit
repeatedly.
You can see “OPT” on the display window if
connecting normally between this unit and your
TV.
y
Before connecting the optical cable, be sure
to remove the protection plug cover if your
cable has the cover.
y
You can enjoy the TV audio through the
speakers of this unit. In the case of some TV
models, you must select the external speaker
option from the TV menu. (For details,
reference your TV user manual.)
y
Set up the sound output of TV to listen to
the sound through this unit:
TV setting menu
[
[Sound]
[
[TV Sound
output]
[
[External speaker (Optical)]
y
Details of TV setting menu vary depending
on the manufacturers or models of your TV.
y
If this unit is connected by OPTICAL and ARC
at the same time, the ARC signal is a high
priority.
,
Note
LG Sound Sync
You can control some functions of this unit by
your TV’s remote control with LG Sound Sync. It is
compatible with the LG TV that is supported LG
Sound Sync. Make sure of the LG Sound Sync logo on
your TV.
Controllable function by LG TV’s remote control:
Volume up/down, mute
Refer to the TV’s instruction manual for the details of
LG Sound Sync.
Make one of the following connections, depending on
the capabilities of your equipment.
y
You can also use the remote control of this
unit while using LG Sound Sync. If you use TV’s
remote control again, the unit synchronizes
with the TV. According to TV Specications,
the volume and mute of this unit synchronize
with TV.
y
When the connection fails, make sure of the
condition of the TV and power.
y
Make sure of the condition of this unit and
the connection in the cases below when using
LG Sound Sync.
- The unit is turned off.
- Changing the function to the others.
- Disconnecting the optical cable.
y
The amount of time to turn off this unit is
different depending on your TV when you set
AUTO POWER function to ON.
,
Note
Connecting16
Connecting
2
LG Sound Sync with wired connection
1. Connect your LG TV to the unit by using an
optical cable.
Optical cable
2. Set up the sound output of TV to listen to the
sound through this unit:
TV setting menu
[
[Sound]
[
[TV Sound
output]
[
[LG Sound Sync (Optical)]
3. Turn on the unit by pressing
1
on the remote
control or
1
on the unit.
4. Select OPT/HDMI ARC function by using F on the
remote control or F on the unit until the function
is selected.
You can see “LGOPT” on the display window if
connecting normally between this unit and your
TV.
Details of TV setting menu vary depending on
the models of your TV.
,
Note
LG Sound Sync with wireless
connection
1. Turn on the unit by pressing
1
on the remote
control or
1
on the unit.
2. Select LG TV function by using F on the remote
control or F on the unit until the function is
selected.
3. Set up LG Sound Sync (Wireless) on the TV. Refer
to the TV’s instruction manual.
“PAIRED” appears on the display window for
about 3 seconds and then you can see “LG TV”
on the display window if connecting normally
between this unit and your TV.
y
If you turned off the unit directly by pressing
1
(Power), LG Sound Sync (Wireless) will be
disconnected.
y
If your TV and this unit are connected through
LG Sound Sync (Wireless), this unit will be
Network standby mode regardless of the
status of network connection when this unit
is turned off. Check dimmed white LED on the
unit.
,
Note
Connecting 17
Connecting
2
Using an HDMI cable
If you connect this unit to a TV that supports HDMI
CEC and ARC (Audio Return Channel), you can
enjoy the TV audio through the speakers of this unit
without connecting the optical cable.
1. Connect the HDMI OUT (TV ARC) jack on the
back of the unit to ARC jack on the TV using an
HDMI cable.
HDMI cable
2. Select the input source to OPT/HDMI ARC
by pressing F button on the remote or unit
repeatedly.
You can see “ARC” on the display window if
connecting normally between this unit and your
TV.
y
You can enjoy the TV audio through the
speakers of this unit. In the case of some TV
models, you must select the external speaker
option from the TV menu. (For details,
reference your TV user manual.)
y
Set up the sound output of TV to listen to
the sound through this unit:
TV setting menu
[
[Sound]
[
[TV Sound
output]
[
[External speaker (HDMI ARC)]
y
Details of TV setting menu vary depending on
the manufacturers or models of your TV.
y
Depending on your LG TV model, you may
need to turn on the SIMPLINK function on
your LG TV.
y
When you return to ARC function from
another function, you need to select the input
source to OPT/HDMI ARC. Then this unit
changes to ARC function automatically.
,
Note
ARC (Audio Return Channel)
function
The ARC function enables an HDMI capable TV to
send the audio stream to HDMI OUT of the unit.
To use this function:
- Your TV must support the HDMI-CEC and ARC
function and the HDMI-CEC and ARC must be set
to On.
- The setting method of HDMI-CEC and ARC may
differ depending on the TV. For details about ARC
function, refer to your TV manual.
- You must use the HDMI cable (Type A, High Speed
HDMI™ cable with Ethernet).
- You must connect the HDMI OUT on the unit with
HDMI IN of the TV that supports ARC function
using an HDMI cable.
- You can connect only one Sound bar to TV
compatible with ARC.
What is SIMPLINK?
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.
Controllable functions by LG TV’s remote control:
Power on/off, volume up/down, etc.
Refer to the TV owner’s manual for the details of
SIMPLINK function.
LG TV’s with SIMPLINK function has the logo as
shown above.
y
Depending on the state of the unit, some
SIMPLINK operation may differ from your
purpose or not work.
y
Depending on a TV or a player which is
connected with this unit, SIMPLINK operation
may differ from your purpose.
,
Note
Connecting18
Connecting
2
Additional information for HDMI
y
When you connect an HDMI or DVI compatible
device make sure of the following:
- Try switching off the HDMI/DVI device and this
player. Next, switch on the HDMI/DVI device and
leave it for around 30 seconds, then switch on
this player.
- The connected devices video input is set
correctly for this unit.
- The connected device is compatible with
720 x 576p (or 480p), 1280 x 720p,
1920 x 1080i, 1920 x 1080p video input.
y
Not all HDCP-compatible HDMI or DVI devices will
work with this player.
- The picture will not be displayed properly with
non-HDCP device.
y
If a connected HDMI device does not accept
the audio output of the player, the HDMI
devices audio sound may be distorted or may
not output.
y
Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off
the player and then turn it on again.
y
When the HDMI connection with HDCP is not
veried, TV screen is changed to black screen.
In this case, check the HDMI connection, or
disconnect the HDMI cable.
y
If there are noises or lines on the screen,
please check the HDMI cable (length is
generally limited to 4.5 m).
y
You cannot change the video resolution in the
HDMI IN mode. Change the video resolution
of the connected component.
y
If the video output signal is abnormal when
your personal computer is connected to HDMI
IN jack, change the resolution of your personal
computer to 576p (or 480p), 720p, 1080i or
1080p.
,
Note
HDMI cable Checklist
Some HDMI cables have poor signal transmission,
which can cause problems with sound and video
transmission.
Even after HDMI cable connections, if no sound,
sound interrupted, noise occurring from the sound
bar and/or no video, no smooth video on your TV, the
HDMI cable may be the problem.
Use the cable marked with the premium HDMI
certication logo. Also make sure that the your
using cable is a certied Type A, Ethernet high-speed
HDMI™ cable.
STANDARD HDMI CABLE WITH ETHERNET
HIGH SPEED HDMI CABLE
HIGH SPEED HDMI CABLE WITH ETHERNET
(X)
(X)
(O)
Connection through HDMI Cable*
Your television must support the newest HDMI
features (HDMI CEC
1)
/ ARC (Audio Return Channel))
to fully enjoy the Live broadcasting channel with
audio system through an HDMI cable. Unless your
TV supports these HDMI features, the audio system
should be connected through an OPTICAL cable.
1) HDMI CEC (High-Denition Multimedia Interface
Consumer Electronics Control)
Consumer Electronics Control (CEC) is an HDMI
feature designed to allow the user to command and
control the CEC-enabled devices, that are connected
through HDMI by using only one of their remote
controls.
* Trade names for CEC are SimpLink (LG) , Anynet+
(Samsung), BRAVIA Sync (Sony), EasyLink (Philips),
etc.
Connecting 19
Connecting
2
Optional equipment
connection
HDMI connection
You can enjoy the sound from the external device
which is connected to HDMI IN jack on this unit.
To the Blu-ray disc player,
DVD player, etc.
1. Connect HDMI IN jack on the back of the unit to
HDMI OUT jack on the audio device such as Blu-
ray disc player, DVD player, etc.
2. Set the input source to HDMI. Press repeatedly F
on the remote control or F on the unit until the
function is selected.
OPTICAL IN connection
Connect an optical output jack of external devices to
the OPTICAL IN jack.
Optical cable
To the optical output
jack of external device
1. Connect the OPTICAL IN jack on the back of the
unit to optical out jack of your external device.
2. Select the input source to OPT/HDMI ARC
by pressing F button on the remote or unit
repeatedly.
You can see “OPT” on the display window if
connecting normally between this unit and your
device.
Before connecting the optical cable, be sure to
remove the protection plug cover if your cable
has the cover.
,
Note
Connecting20
Connecting
2
PORTABLE IN connection
Listening to music from your portable
player
The unit can be used to play the music from many
types of portable players or external devices.
1. Connect the portable player to the PORTABLE IN
connector of the unit.
2. Turn the power on by pressing
1
(Power).
3. Select the PORT. function by pressing F on the
remote control or F on the unit until the function
is selected.
4. Turn on the portable player or external device and
start playing it.
Optional equipment connection
You can enjoy both sound and picture from the
external device you connect.
OR
1. Connect HDMI IN jack of your TV to HDMI OUT
jack on the external device such as Blu-ray disc
player, DVD player, etc.
2. Connect the OPTICAL IN jack on the back of the
unit to OPTICAL OUT jack on the TV using an
OPTICAL cable.
Or connect the HDMI OUT (TV ARC) jack on the
back of the unit to HDMI IN (ARC) jack on the TV
using an HDMI cable.
3. Set the input source to OPT/HDMI ARC. Press
repeatedly F on the remote control or F on the
unit until the function is selected.
If the sound bar does not have sound or the
video on TV is not smooth, the HDMI cable
may be the problem. Refer to the HDMI cable
checklist. (Page 18)
,
Note
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

LG SK6 User manual

Category
Soundbar speakers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI