Jeco FCL125 Operating instructions

Brand
Jeco
Model
FCL125
Type
Operating instructions

This manual is also suitable for

Jeco FCL125 is a fountain pump with adjustable speed that can be used to create a variety of water features. A notable advantage of the pump is that it is capable of lifting water multiple levels which makes it suitable for fountains with a significant height difference between the water source and the highest point of the water feature. The adjustable speed allows the user to customize the flow rate and height of the water stream to their preference. The pump is easy to install and maintain, making it a great choice for both indoor and outdoor use.

Jeco FCL125 is a fountain pump with adjustable speed that can be used to create a variety of water features. A notable advantage of the pump is that it is capable of lifting water multiple levels which makes it suitable for fountains with a significant height difference between the water source and the highest point of the water feature. The adjustable speed allows the user to customize the flow rate and height of the water stream to their preference. The pump is easy to install and maintain, making it a great choice for both indoor and outdoor use.

3. Periodically change water and keep water clean. We recommend distilled water to prevent mineral build-up.
This instruction relates ONLY to this water fountain product and contains important information for using
the product for the first time. Please keep it for later reference. This instruction should always accompany
the product in the event of transfer to a new user.
1.Unpack the product. Read this instruction sheet before proceeding.
2.Familiarize yourself with the pump. The pump speed is controlled by the
switch located at the front of the pump. The speed is indicated by plus(+) and
minus (-) sign. To increase the speed, move to each speed level. At its highest
speed level, the switch will cease to move any further, vice versa.
3.Place the product on a flat surface, remove plastic bag from packaging.
4.Attach pump to water tube, resting pump inside bottom.
5.Fill base pond with tap water to 3cm from the edge of the base. Make sure
there is no solid impurity in the water, or it will affect the pumps work;
6.Insert the plug into the power socket, If installed properly, water will begin
flowing.
Please note: On first use, there may be air in the pump, It can take up to a
few minutes until the air escapes.
3. Make sure the water tube is properly connected with the pump and the upper layer, and do not crimp the tube otherwise
water will not come out.
4. During operation, the area around the pump will be covered with water. Take care when handling the pump; do not pull
pump out of water (when running) by the power cord, and do not move the product when running.
5. Unplug pump and power before servicing, cleaning, or moving.
Cleaning and Maintenance:
1. If after time the pump starts to lose power or stops working you should check for the build up of sediment or scale at the
bottom of the pump housing or in reservoir.
2. Remove the impeller or any dirt and scale, which has built up and close the case back up.
Safety Guidelines:
1. Read all instructions and safety guidelines thoroughly. Failure to follow guideline and instructions could result in serious
injury and/or property damage.
2. Do not pump flammable liquids such as gasoline / fuel oil with the fountain pump.
INTRODUCTION
INSTRUCTION MANUAL
Product Feature: The product consists: (1)Fountain top (2) Fountain base (3) baffle plate (4) Pump
(Please read pump user manual).
Instructions for use:
Thank you for purchasing this fountain. You have purchased a product that complies with
the latest design and with a creative theme.
This product is carefully packaged, inspected, and tested to ensure safe operation and
delivery. The following instructions and safety guidelines will enable you to use the
product for trouble-free operation. Please read the insturctions and safety guidelines
entirely before using the product.
  • Page 1 1

Jeco FCL125 Operating instructions

Brand
Jeco
Model
FCL125
Type
Operating instructions
This manual is also suitable for

Jeco FCL125 is a fountain pump with adjustable speed that can be used to create a variety of water features. A notable advantage of the pump is that it is capable of lifting water multiple levels which makes it suitable for fountains with a significant height difference between the water source and the highest point of the water feature. The adjustable speed allows the user to customize the flow rate and height of the water stream to their preference. The pump is easy to install and maintain, making it a great choice for both indoor and outdoor use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents