PARTS LIST FOR COMMERCIAL DISPOSERS
MODEL SS-75 IN-SINK-ERATOR® 3/4 H.P.
(Includes Models SS-75-1, SS-75-2, SS-75-3)
ORDER BY PART NUMBER, NOT CODE NUMBER
(Minimum Paris Order $3.00)
(All PARTS F.O.B. FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)
EFFECTIVE March, 1972
PARTS LIST FOR COMMERCIAL DISPOSERS
MODEL SS-75 IN-SINK-ERATOR 3/4 H.P.
(Includes Models 'SS-75-1, SS-75-2, SS-75-3)
ORDER BY PART NUMBER, NOT CODE NUMBER
(Minimum Parts Order $3.00)
(ALL PARTS F.O.B. FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)
Form No. C-123-72C PRINTED IN U.S.A.
Code
No.
Part No.
No.
Reqd.
Description
37 12549-A 1 Stator Assembly
208 Volt, 60 Cycle, Three Phase
38 12352-A 1 Stator Assembly
230/460 Volt, 60 Cycle, Three Phase
39 12433 1 Terminal Box Mounting Bracket •
Single Phase
40 12433-E 1 Terminal Box Mounting Bracket -
Three Phase
41 11448 4 Screw
42 12384 1 Bushing
43 11868 1 Capacitor - Single Phase Only
44 12387 1 Overload Protector
(Use above serial #42555 only)
208 Volt, 60 Cycle. Single Phase
115/230 Volt, 60 Cycle, Single Phase
44 12643 1 Overload Portector.
(Use below serial #42555 only) . :
208 Volt, 60 Cycle, Single Phase :
115/230 Volt, 60 Cycle, Single Phase
45 12616 1 Overload Protector
(Use above serial #42699 only)
208 Volt, 60 Cycle, Three Phase
45 12388 1 Overload Protector
(Use below serial #42699 only)
208 Volt,60 Cycle, Three Phase
46 12388 1 Overload Protector
230/460 Volt, 60 Cycle, Three Phase
47 12378 1 Clamp, Overload
48 5765 2 Screw
49 12372
1
Terminal Box
50 12383
1
Grommet
51 12381
1
Screw
52 12415
1
Bearing - Lower
53 12399
1
Spring, Pre-load
54 12684
1
End Frame, Lower
55 12395
1
Fan
56 12635
1
Retaining Ring
57 12490 3 Tube, Spacer
58 11940 3 Bolt, Thru
59 12396 1 Cover, Bottom
60 12586 2 Plug
61 11757-B 2 Leg (Optional)
62 12564 1 Ground Screw
Code
No.
Part No.
No.
Reqd.
Description
1 11004 1 Mounting Flange
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Container
4 1491 6 Bolt, Mounting
5 11227 1 Pipe Plug
6 11006 1 Seal, Body-Shredder
7 12442 1 Body and Cover Assembly
8 112S2-A 1 Stationary Shredder
9 11260 1 Nut, Shredder
10 12445 1 Washer
11 12142 1 Washer, Fibre
12 12316 1 Rotor Shredder
13 12327 1 Upper End Bell - Includes
Codes 14-16-17-18
14 12321 1 Face Seal
15 12318 1 Spacer Sleeve
16 12319 1 Centrifugal Moisture Shield
17 12610 1 Bearing Assembly - Upper
18 12326 1 Oil and Water Retainer
19 11322 2 Woodruff Key
20 12611
Bearing - Seal Kit Includes
Codes 9-10-11-14-15-16-17-18-19
21 11444 3 Washer
22 1491 3 Bolt
23 1470 1 Washer, Tail Pipe
24 5487 1 Tail Pipe
25 1461 1 Flange - Tail Pipe
26 1468 2 Bolt - Tail Pipe
27 12330-A
Rotor & Shaft Assembly (Includes
Codes 29 & 30)i
208 Volt, 60 Cycle, Single Phase &
115/230 Volt, 60 Cycle, Single Phase
28 12331-A
Rotor & Shaft Assembly
208 Volt, 60 Cycle, Three Phase &
230/460 Volt, 60 Cycle, Three Phase
29 1537 2 Spring - Centrifugal Switch
30 12348 1 Centrifugal Switch
31 7422 2 Screw
32 12393 1 Start Switch
33 5765 2 Screw
34 12370 1 Shell - Trim
35 12351-E 1 Stator Assembly
208 Volt, 60 Cycle, Single Phase '
36 12351-A 1 Stator Assembly
115/230 Volt, 60 Cycle, Single Phase
EMERSON
IN-SINK-ERATOR DIVISION
EMERSON ELECTRIC CO.
4700-21ST STREET
RACINE, WISCONSIN 53406
PHONE: (414) 637-6761
CANADIAN
MODEL
MODEL
SS
-
75
-
10
115/230/60/1
SS
-
75
-
16
ISE
SS
-
75
-
11
208/60/1
SS
-
75
-
17
SS
-
75
-
12
230/460/60/3
SS
-
75
-
18
IN-SINK-ERATOR
SS
-
75
-
13
208/60/3
SS
-
75
-
19
Start with Serial #70,000
ORDER BY PART NUMBER, NOT CODE NUMBER
(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)
September,
1979
3
/4
H.P.
MODEL
CANADIAN
MODEL
SS-75-10 115/230/60/1 SS-75-16
SS-75-11 208/60/1 SS-75-17
SS-75-12 230/460/60/3 SS-75-18
SS-75-13 208/60/3 SS-75-19
Code
No.
Part No.
No.
Req.
Description
1l 11004 1 Mounting Flange
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Container
4 1491 6 Bolt, Mounting
5 11227 1 Pipe Plug
6 11006 1 Seal, Body-Shredder
7 12442 1 Body and Cover Assembly
8 11252-A 1 Stationary Shredder
9 11260 1 Nut, Shredder ,
10 12445 1 Washer
11 12142 1 Washer, Fibre
12 12944 1 Rotor Shredder
13 13081 1 End Bell Upper, Includes Codes
14 thru 21
14 12936 1 Shield
15 12937 6 Screw
16 12934-A Seal Assembly
17 12935
Sleeve, Spacer
18 12860
O'Ring
19 12319
Centrifugal Moisture Shield
20 12610
Bearing Assembly - Upper
21 12326
Oil and Water Retainer
22 11322 3 Woodruff Key
23 13080 1 Bearing - Seal Kit Includes Codes 9, 10
11, 14, 15, 16, 17, 18, 19, 20, 21, 22
24 11444 3 Washer
25 1491 3 Bolt
26 1470 1 Washer, Tail Pipe
27 5487 1 Tail Pipe
28 1461 1 Flange - Tail Pipe
29 1468 2 Bolt - Tail Pipe
30 12947-A 1 Rotor & Shaft Assembly
Includes Code #31
208 Volt, 60 Hz. Single Phase &
115/230 Volt, 60 Hz, Single Phase
31 12954 1 Centrifugal Switch Assembly
32 12948-A 1 Rotor & Shaft Assembly
208 Volt, 60 Hz, Three Phase
230/460 Volt, 60 Hz, Three Phase
33 7422 2 Screw
34 12393 1 Start Switch
35 12370 1 Shell-Trim
36 13075-C 1 Stator Assembly '
115/230 Volt, 60 Hz, Single Phase
ORDER BY PART NUMBER, NOT CODE NUMBER
(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)
IN-UNK-ERATOR DIVISION
EMERSON ELECTRIC CO.
4700-21ST STREET
RACINE. WISCONSIN 53406
ISE
PHONE: (414) 554-5432
IN SINK ERATOR®
PRINTED IN U 5 A
Code
No.
Part No.
No.
Req.
Description
37 13075-B 1 Stator Assembly
208 Volt, 60 Hz, Single Phase
38 13077-A 1 Stator Assembly
230/460 Volt, 60 Hz, Three Phase
39 13076-A 1 Stator Assembly
208 Volt, 60 Hz, Three Phase
40 12433 1 Terminal Box Mounting Brocket
Single Phase
41 12433-A 1 Terminal Box Mounting Bracket
Three Phase
42 11448 4 Screw
43 12384 1 Bushing
44 11868 1 Capacitor (Single Phase Only)
45 12387 1 Overload Protector
115/230 Volt, 60 Hz, Single Phase
208 Volt, 60 Hz, Single Phase
46 12388 1 Overload Protector
230/460 Volt, 60 Hz, Three Phase
47 12616 1 Overload Protector
208 Volt, 60 Hz, Three Phase
48 12378 1 Clamp, Overload
49 5765 2 Screw
50 12372 1 Terminal Box
51 12383 1 Grommet
52 12381 1 Screw
53 12415 1 Bearing, Lower
54 12399 1 Spring, Pre-load
55 12684 1 End Frame, Lower
56 12395 1 Fan
57 12635 1 Retaining Ring
58 12490 3 Tube, Spacer
59 11940 3 Bolt, Thru
60 12396 1 Cover, Bottom
61 12564 1 Ground Screw
62 1175 7-8 2 Leg (Optional)
CANADIAN ONLY
63 12643 1 Overload Protector
115/230 Volt, 60 Hz, Single Phase
64 12387 1 Overload Protector
208 Volt, 60 Hz, Single Phase
65 12616 1 Overload Protector
230/460 Volt, 60 Hz, Three Phase
208 Volt, 60 Hz, Three Phase
11005
SPLASH BAFFLE
11249
SLEEVE GUARD
4173
JAM RELEASE BAR
COMMERCIAL DISPOSER
Start Date:
03/04/82
ISE
MODEL NO. SS75
-
15
Engineer Number:
IN-SINK-ERATOR
9230/460V/50Hz/3 Phase
13024K
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020A 1 Body, Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe. Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper
(lnd.Codes14.22)
14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.
Codes 9-11 & 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
29
1468
2
Screw, Tailpipe
30 12948B 1 Rotor & Shaft Assy
(Inc). Codes 45)
31 12370 1 Trim, Band
32 1836A 2 Screw
33 13077B 1 Stator Assy
34 12433E 1 Bracket Assy
(Mounting)
35 11448 4 Screw
36 12357 1 Insulation Tube
37 13128P 1 Overload, Protector
38 12378 1 Clamp, Overload
39 5765 2 Screw, Tapping
40 13396 1 Box, Terminal Assy
(Incl. code 42)
41 12381 1 Screw
42 12383 1 Grommet, Overload
43 12384 1 Bushing
44 2466A 1 Screw, Ground
45 12415 1 Bearing, Lower
46 12399 1 Washer, Spring
47 12684 1 End Frame, Lower
48 12395 1 Fan
49 12635 1 Ring, Retaining
50 12490 3 Tube,Spacer
51 12396 1 Cover, Bottom
52 11940A 3 Bolt, Thru
53 11757B 2 Tube Assy, Foot
(Optional)
3/4 H.P.
COMMERCIAL DISPOSER
Start Date:
03/01/82
ISE
MODEL NO. SS75
-
21
Engineer Number:
IN-SINK-ERATOR (308 Volt/50Hz/3 Phase) 13024T
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020A 1 Body, Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe, Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy. Rotor
13 13081 1
End Bell Assy, Upper
(Incl. Codes 14-22)
14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1
Bearing Seal Kit (Incl. codes9-11
& 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
29
1468
2
Screw, Tailpipe
30 12948B 1 Rotor & Shaft Assy
(Ind. Codes 45)
31 12370 1 Trim, Band
32 1836A 2 Screw
33 13077C 1 Stator Assy
34 12433E 1
Bracket Assy (Mounting)
35 11448 4 Screw
36 12357 1 Insulation Tube
37 13422N 1 Overload, Protector
38 12378 1 Clamp, Overload
39 8221 2 Screw, Tapping
40 13396 1
Box, Terminal Assy
(Ind. code 42)
41 12381 1 Screw
42 12383 1 Grommet, Overload
43 12384 1 Bushing
44 2466A 1 Screw, Ground
45 12415 1 Bearing, Lower
46 12399 1 Washer, Spring
47 12684 1 End Frame, Lower
48 12395 1 Fan
49 12635 1 Ring, Retaining
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52 11940A 3 Bolt, Thru
53 11757B 2 Tube Assy, Foot
(Optional)
3/4 H. P.
COMMERCIAL DISPOSER
MODEL
ISE
SS-75-23
115/208/230/60/1
IN
-
SINK
-
ERATOR
SS-75-24
208/230/460/60/3
ORDER BY PART NUMBER, NOT CODE NUMBER
(All P»rts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)
May, 1985
3/4
H.P.
COMMERCIAL DISPOSER
Start Date:
MODEL NO. SS75
-
24
7/87
U.S.A.
Engineer Number:
IN-SINK-ERATOR
(208-230/460/60/3Ø)
13384A
3/4 H.P.
CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket Mounting
3 11020-A 1 Body Any, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Any
8 11252.A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper
(Incl Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 1)322 3 Key, Woodruff
23 13080 1
Bearing Seal Kit
(Incl Codes 9-11 & 14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipo
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw, Tailpipe
CODE
NO.
PART NO. NO. REQ.
DESCRIPTION
30
12948
-
A
1
Rotor & Shaft Assy
31 12370 1 Trim, Band
32 1836-A 2 Screw
33 13077-A 1
Stator Assy (Three Phase)
34 12433-E 1 Bracket, Terminal Box
(Three Phase)
35 11448 4 Screw
36 12384 1 Bushing
37 13422-K 1 Overload, Protector
(Three Phase)
38 12378 1 Clamp. Overload
39 5765 2 Screw, Tapping
40 12372 1 Box, Terminal
41 12381 1 Screw
42 12383 1 Grommet, Overload
43 12415 1 Bearing, Lower
44 12399 1 Washer, Spring
45 12684 1 End Frame, Lower
46 12395 1 Fan
47 12635 1 Ring, Retaining
48 12490 1 Tube, Spacer
49 11940-A 1 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot
(Optional)
53 12357 1 Insulation Tube
(Three Phase Only)
COMMERCIAL DISPOSER Start Date:
MODEL NO.SS75
-
25
7/87
CANADIAN Engineer Number:
IN-SINK-ERATOR
(115/208-230/60/1Ø) 13384B
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO.
PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper
(IncI Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit
(IncI Codes 9-11
& 14 thru 22)
24 11444 3 Washer, lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 5487 1 Toilpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw, Tailpipe
30 12947-A 1 Rotor & Shaft Assy
(Single Phase)
(IncI Codes 31 & 47)
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
31
12954
1
Centrifugal Actuator
(Single Phase Only)
32 8221 2 Screw
33 12393 1 Switch, Start
(Single Phase Only)
34 12370 1 Trim, Band
35 1836-A 2 Screw
36 13075-C 1 Stator Assy
(Single Phase)
37 12433 1 Bracket Assy
(Mounting) (Single Phase)
38 11448 4 Screw
39 12384 1 Bushing
40 11868 1 Capacitor
(Single Phase Only)
41 13422-J1 1 Overload, Protector
(Single Phase)
42 12378 1 Clamp, Overload
43 5765 2 Screw, Tapping
44 12372 1 Box, Terminal
45 12381 1 Screw
46 12383 1 Grommet, Overload
47 12415 1 Bearing, Lower
48 12399 1 Washer, Spring
49 12684 1 End Frame, Lower
50 12395 1 Fan
51 12635 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-A 1 Screw, Ground
56 11757-B 2 Tube Assy, Foot
(Optional)
COMMERCIAL DISPOSER
Start Date:
09/09/92
MODEL NO. SS75-27
Engineer Number:
IN-SINK-ERATOR
(115/208/230 Volt/60Hz/1 Phase) 13659
3/4 H.P.
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
1
11004
1
Range, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Plug, Pipe
6 11006 1 Gasket, Shredder
7 12442 1 Assy, Body & Cover
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Assy, Rotor Shredder
13 13722 1 Assy, Upper End Bell
(Incl. Codes 14-22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Assy, Upper Bearing
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1
Kit, Bearing Seal (Incl. codes 9-11
& 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-A 1 Rotor & Shaft Assy.
(Incl. Codes 31 & 47)
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
1
13708
1
Centrifugal Actuator
32 8221 2 Screw (8-32x1/2)
33 13707 1 Switch, Start
34 12370 1 Trim Band
35 1836-A 2 Screw (8-32x1/2)
36 13713-A 1 Stator Assy
37 12433 1 Bracket Assy
(Mounting)
38 11448 4 Screw (8-18x1/4)
39 12384 1 Bushing
40 11866 1 Capacitor
41 13422J 1 Overload Protector
42 12378 1 Clamp, Overload
43 8221 2 Screw (8-32x1/2)
44 13396 1 Box, Terminal Assy
(Incl. code 46)
45 12381 1 Screw (8-32x1-1/4)
46 12383 1 Grommet, Overload
47 13709 1 Bearing, Lower
48 13678 1 Spring, Pre-load
49 13710 1 End Frame, Lower
50 13676 1 Fan
51 13677 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-A 1 Screw, Ground
56 11757-B 2 Tube,Foot Assy.
(Optional)
COMMERCIAL DISPOSER
Start Date:
9-1-92
MODEL NO. SS75-28
Engineer Number:
IN-SINK-ERATOR
(208/230-460 Volt/60Hz/3 Phase)
13659-A
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 .1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper
(Incl. Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Wood luff
23 13080 1 Bearing Seal Kit (Incl.
codes 9-10-11 & 14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
28
1461
1
Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy
(Incl. Code 43)
31 12370 1 Trim.Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-A 1 Stator Assy
34 12433-E 1 Bracket Assy
(Mounting)
35 11448 4 Screw (8-18x1/4)
36 12384 1 Bushing
37 13422-K 1 Overload, Protector
38 12378 1 Clamp, Overload
39 8221 2 Screw (8-32x1/2)
40 13396 1 Box, Terminal
(Ind. code 42)
41 12381 1 Screw (8-32x1-1/4)
42 12383 1 Grommet, Overload
43 13709 1 Bearing, Lower
44 13678 1 Spring, Pre-load
45 13747 1 End Frame, Lower
46 13676 1 Fan
47 13677 1 Ring, Retaining
48 12490 3 Tuba, Spacer
49 11940-A 3 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot
(Optional)
3/4 H.P
.
COMMERCIAL DISPOER Start Date:
9-1-92
MODEL NO. SS75-28
Engineer Number:
IN-SINK-ERATOR
(208/230/460 Volt/60Hz/3 Phase) 13659-A
3/4 H.P.
ORDER BY PART NUMBER. NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Plug, Pipe
6 11006 1 Gasket, Shredder
7 12442 1 Assy, Body & Cover
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Assy, Rotor Shredder
13 13722 1 Assy, Upper End Bell
(lncl.Codes14-22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Assy, Upper Bearing
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Kit, Bearing Seal (Ind.
codes 9-11 & 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-A 1 Rotor & Shaft Assy.
(Incl. Codes 31 & 47)
CODE NO. PART NO. NO. REQ. DESCRIPTION
31
13708
1
Centrifugal Actuator
32 8221 2 Screw (8-32X1/2)
33 13707 1 Switch, Start
34 12370 1 Trim Band
35 1836-A 2 Screw (8-32x1/2)
36 13713-A 1 Stator Assy
37 12433 1 Bracket Assy
(Mounting)
38 11448 4 Screw (8-18X1/4)
39 12384 1 Bushing
40 11868 1 Capacitor
41 13422J 1 Overload Protector
42 12378 1 Clamp, Overload
43 8221 2 Screw (8-32x1/2)
44 13396 1 Box, Terminal Assy
(Incl. code 46)
45 12381 1 Screw (8-32x1-1/4)
46 12383 1 Grommet, Overload
47 13709 1 Bearing, Lower
48 13678 1 Spring, Pre-load
49 13710 1 End Frame, Lower
50 13676 1 Fan
51 13677 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-A 1 Screw, Ground
56 11757-B 2 Tube, Foot Assy.
(Optional)
COMMERCIAL DISPOSER Start Date:
02/26/93
MODEL NO. SS75-30 (C.S.A.)
Engineer Number:
IN-SINK-ERATOR
(208/230/460 Volt/60Hz/3 Phase) 13569-C
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
1
11004
1
Flange
, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper
(Incl. Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Beahng Assy, Upper
21 12326 1 Seal, Water& Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl,
codes 9-10-11 & 14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
3/4 H.P.
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
28
1461
1
Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy
(Incl. Code 43)
31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714 -A 1 Stator Assy
34 12433-E 1 Bracket Assy
(Mounting)
35 11448 4 Screw (8-18x1/4)
36 12384 1 Bushing
37 13422-K 1 Overload, Protector
38 12378 1 Clamp, Overload
39 8221 2 Screw (8-32x1/2)
40 13396 1 Box, Terminal
(Incl. code 42)
41 12381 1 Screw (8-32x1-1/4)
42 12383 1 Grommet, Overload
43 13709 1 Bearing, Lower
44 13678 1 Spring, Pre-load
45 13747 1 End Frame, Lower
46 13676 1 Fan
47 13677 1 Ring, Retaining
48 12490 3 Tube, Spacer
49 11940-A 3 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot
(Optional)
COMMERICAL DISPOSER Start Date:
04/21/93
MODEL NO. SS75-31(EXPORT)
Engineer Number:
IN-SINK-ERATOR
(115/230Volt/50Hz/1Phase) 13659-D
3/4 H.P.
ORDER BY PART NUMBER. NOT CODE NUMBER
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mount
ing
2
11016
1
Gasket, Mounting
3
11020
-
A
1
Body, Assy, Upper
4
1491
6
Screw
(1/4
-
20x3/4)
5
11227
1
Plug, Pipe
6
11006
1
Gasket, Shredder
7
12442
1
Assy, Body
&
Cover
8
11252
-
A
1
Shredder, Stationary
9
11260
1
Nut
10
12445
1
Washer
11
12142
1
Wash
er. Fiber
12 12944 1 Assy, Rotor Shredder
13
13722
1
Assy, Upper End Bell
(lncl.Codes14.22)
14
12936
1
Shield
15 1269 6 Screw (8-18x1/2)
16
12934
-
A
1
Assy, Seal
17
12935
1
Sleeve, Spacer
18
12860
1
O
-
Ring
19
12319
1
Slinger
20
12610
1
Assy,
Upper Bearing
21
12326
1
Seal. Water
&
Oil
22
11322
3
Key, Woodruff
23
13080
1
Kit, Bearing Seal (Incl.
Codes9
-
11 &14
-
22)
24
11444
3
Washer. Lock
25 3135 3 Screw (1/4-20x1)
26
1470
1
Gasket, Tailpipe
27
5487
1
Tailpipe
28
1461
1
Range, Tail
pipe
29
1468
2
Screw
(1/4
-
20x1/2)
30
13674
-
D
1
Rotor
&
Shaft Assy.
(Incl. Codes 31 & 48)
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
31
1413l
1
Centrifugal Actuator
32 8221 2 Screw (8-32x1/2)
33 13707 1 Switch. Start
34 12370 1 Trim Band
35 1636-A 2 Screw (8-32x1/2)
36 13713-Q 1 Stator Assy
37 12433 1 Bracket Assy
(Mounting)
38 11448 4 Screw (8-18x1/4)
39 11868 1 Capacitor
40 12378 1 Clamp, Overload
41 8221 2 Screw (8-32x1/2)
42 13396 1 Box, Terminal Assy
(Incl. code 46)
43 12381 1 Screw (8-32x1-1/4)
44 12383 1 Grommet, Overload
45 13422-L
1 Overload Protector
46 12384 1 Bushing
47 2466-A 1 Screw, Ground
48 13709 1 Bearing, Lower
49 13678 1 Spring, Pre-load
50 13710 1 End Frame, Lower
51 13676 1 Fan
52 13677 1 Ring, Retaining
53 12490 3 Tube, Spacer
54 11940-A 3 Bolt. Thru
55 12396 1 Cover, Bottom
56 11757-B 2 Tube, Foot Assy.
(Optional)
COMMERCIAL DISPOSER Start Date:
04/21/93
MODEL NO. SS75-32 (EXPORT)
Engineer Number:
IN-SINK-ERATOR
(208/460Volt/50Hz/3Phase) 13659-E
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART NO.
NO.
REQ.
DESCRIPTION
l
11004
1
Flange, Moun
ting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Mug
6 11006 1 Gasket. Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper
(Incl. Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.
codas 9-10-11 & 14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
CODE
NO.
PART NO.
NO.
REQ.
DESCRIPTION
28
1461
1
Range, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy
(Incl. Code 44)
31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-A 1 Staler Assy
34 12433-E 1 Bracket Assy
(Mounting)
35 11448 4 Screw (8-18x1/4)
36 13422-AG 1 Overload, Protector
37 12378 1 Clamp, Overload
38 8221 2 Screw (8-32x1/2)
39 13396 1 Box, Terminal
(Incl. code 42)
40 12381 1 Screw (8-32x1-1/4)
41 12383 1 Grommet, Overload
42 12384 1 Bushing
43 2466-A 1 Screw, Ground
44 13709 1 Bearing, Lower
45 13678 1 Spring, Pre-load
46 13747 1 End Frame, Lower
47 13676 1 Fan
48 13677 1 Ring, Retaining
49 11940-A 3 Bolt, Thru
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52 11757-B 2 Tube Assy, Foot
(Optional)
3/4 H.P.
COMMERCIAL DISPOSER Start Date:
04/21/93
MODEL NO. SS75-33 (EXPORT)
Engineer Number:
IN-SINK-ERATOR
(380 Volt/50Hz/3Phase) 13659-G
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
1
11004
1
Range, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 1 Gasket. Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper
(Incl. Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.
codes 9-10-11 & 14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5457 1 Tailpipe
CODE
NO.
PART NO. NO. REQ. DESCRIPTION
20
1461
1
Range, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy
(Incl. Code 44)
31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-B 1 Stator Assy
34 12433-E 1 Bracket Assy
(Mounting)
35 11448 4 Screw (8-18x1/4)
36 13422-N 1 Overload, Protector
37 12378 1 Clamp, Overload
38 8221 2 Screw (8-32x1/2)
39 13396 1 Box, Terminal
(Incl. code 42)
40 12381 1 Screw (8-32x1-1/4)
41 12383 1 Grommet, Overload
42 12384 1 Bushing
43 2466-A 1 Screw, Ground
44 13709 1 Bearing, Lower
45 13678 1 Spring, Pre-load
46 13747 1 End Frame, Lower
47 13676 1 Fan
48 13677 1 Ring, Retaining
49 11940-A 3 Bolt, Thru
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52 11757-B 2 Tube Assy. Foot
(Optional)
3/4 H.P
.
COMMERCIAL DISPOSER Start Date:
11/01/89
MODEL NO. SD 75
Engineer Number:
IN-SINK-ERATOR
230 Volt/50Hz/1Phase 13531
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
1
12506
-
D
1
No.
5
Mounting Assy
2 11016 1 Gasket, Mounting
3 11020-A 1 Body Assy. Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shreddder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 13549 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper
(Inc Codes 14-22)
14 12936 1 Shield
15 1269 6 Screw, Tqpping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Wooddruff
23 13080 1 Bearing Seal Kit
(Inc Codes 9-11 & 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 3851 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw, Tailpipe
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
30
13551
-
A
1
Rotor & Shaft Assy
(Incl Codes 31 & 45)
31 12954-A 1 Centrifugal Actuator
32 13556 2 Screw
33 12393 1 Switch, Start
34 1836-A 2 Screw
35 12370 1 Trim, Band
36 13075-P 1 Stator Assy
37
1 Bracket Assy. Mounting
38 11448 4 Screw
39 11868 1 Capacitor
40 12384 1 Bushing
41 2466A 1 Screw, Ground
42 12372 1 Box. Terminal
43 12381 1 Screw
44 13559 1 Grommet
45 12415 1 Bearing, Lower
46 12399 1 Washer, Spring
47 13547 1 End Frame, Lower
48 12395 1 Fan
49 12635 1 Ring, Retaining
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52
11940
-
A
3
Bolt, Thru
COMMERCIAL DISPOSER Start Date:
11/01/89
MODEL NO. SD 75-1
Engineer Number:
IN-SINK-ERATOR
415 Volt/50Hz/3 Phase 13532 A
CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 13549 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper
(Inc Codes 14-22)
14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Wooddruff
23 13080 1 Bearing Seal Kit
(Inc Codes 9-11 & 14-22)
24 11444 3 Washer, Lock
25
3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 3851 1 Tailpipe
28 1461 1 Flange. Tailpipe
29 1468 2 Screw, Tailpipe
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
30
12948
-
A
1
Rotor & Shaft Assy
(Incl Codes 42)
31 1836-A 2 Screw
32 12370 1 Trim, Band
33 13077-A 1 Stator Assy
34 12357 1 Insulation, Tubing
35
1 Bracket Assy, Mounting
36 11448 4 Screw
37 12384 1 Bushing
38 2466A 1 Screw, Ground
39 12372 1 Box, Terminal
40 12381 1 Screw
41 13559 1 Grommet
42 12415 1 Bearing, Lower
43 12399 1 Washer, Spring
44 12684 1 End Frame, Lower
45 12395 1 Fan
46 12635 1 Ring, Retaining
47 12490 3 Tube, Spacer
48 12396 1 Cover, Bottom
49
11940
-
A
3
Bolt, Thru
ORDER BY PART NUMBER, NOT CODE NUMBER
COMMERCIAL DISPOSER Start Date:
03/12/93
MODEL NO. SD75-3 (Export)
Engineer Number:
SISSONS
(115/208/230 Volt/50Hz/1Phase) 13711
3/4 H.P.
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Plug, Pipe
6 11006 1 Gasket, Shredder
7 12442 1 Assy, Body & Cover
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer. Fiber
12 12944 1 Assy, Rotor Shredder
13 13722 1 Assy, Upper End Bell
(Incl. Codes 14-22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Stinger
20 12610 1 Assy, Upper Bearing
21 12326 1 Seal. Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Kit. Bearing Seal (Ind.
codes 9-11 & 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Range, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-D 1 Rotor & Shaft Assy.
(Ind. Codes 31 & 47)
CODE NO. PART NO.
NO.
REQ.
DESCRIPTION
31
13708
1
Centrifugal Actuator
32 8221 2 Screw (8-32x1/2)
33 13707 1 Switch, Start
34 12370 1 Trim Band
35 1836-A 2 Screw (8-32x1/2)
36 13713-G 1 Stator Assy
37 12433 1 Bracket Assy
(Mounting)
38 11448 4 Screw (8-18x1/4)
39 12384 1 Bushing
40 11868 1 Capacitor
41 13422-L 1 Overload Protector
42 12378 1 Clamp, Overload
43 8221 2 Screw (8-32x1/2)
44 13396-D 1 Box, Terminal Assy
(Ind. code 46)
45 12381 1 Screw (8-32x1-1/4)
46 13559 1 Plug, Button
47 13709 1 Bearing, Lower
48 13678 1 Spring, Pre-load
49 13710 1 End Frame, Lower
50 13676 1 Fan
51 13677 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-B 1 Screw, Ground
56 11757-B 2 Tube, Foot Assy.
(Optional)
COMMERCIAL DISPOSER Start Date:
02/26/93
MODEL NO. SD75-4 (Export)
Engineer Number:
SISSONS
(208/230/460Volt/50Hz/3Phase) 13711-A
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 1 Gasket. Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary
9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer. Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper
(Incl. Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Stinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal. Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.
codes 9-10-11&14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 70076 1 Tailpipe
CODE NO. PART NO. NO. REQ. DESCRIPTION
28
1461
1
Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-K 1 Rotor & Shaft Assy
(Incl. Code 43)
31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-G 1 StatorAssy
34 12433-A 1 Bracket Assy
(Mounting)
35 11448 4 Screw (8-18x1/4)
36 12384 1 Bushing
37 N/A 1 Overioad, Protector
36 12378 1 Clamp, Overload
39 8221 2 Screw (8-32x1/2)
40 13396-D 1 Box, Terminal
(Incl. code 42)
41 12381 1 Screw (8-32x1-1/4)
42 13559 1 Plug, Button
43 13709 1 Bearing, Lower
44 13678 1 Spring, Pre-load
45 13747 1 End Frame, Lower
46 13676 1 Fan
47 13677 1 Ring, Retaining
48 12490 3 Tube, Spacer
49 11940-A 3 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot
(Optional)
3/4 H.P.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
In-Sink-Erator SS-100-3 User manual
-
In-Sink-Erator SS-50 User manual
-
-
-
In-Sink-Erator SS-150 User manual
-
In-Sink-Erator SS-100-28 User manual
-
-
-
-
Other documents
-
Trojan Air Rope Owner's manual
-
InSinkErator SS200-29 User manual
-
Newport Brass 320/15S Installation guide
-
InSinkErator 11599N Installation guide
-
-
-
Hobart FD Disposer Operating instructions
-
Coleman Cable 13569 Datasheet
-
aFe Power 54-11252-2 Installation guide
-
Coleman Cable 13547 Datasheet
