Xilinx SP601 User manual

[Guide Subtitle]

[optional]

UG518 (v1.1) August 19, 2009 [optional]

SP601 Hardware

User Guide

UG518 (v1.1) August 19, 2009

SP601 Hardware User Guide www.xilinx.com UG518 (v1.1) August 19, 2009

Xilinx is disclosing this user guide, manual, release note, and/or specification (the "Documentation") to you solely for use in the development

of designs to operate with Xilinx hardware devices. You may not reproduce, distribute, republish, download, display, post, or transmit the

Documentation in any form or by any means including, but not limited to, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Xilinx. Xilinx expressly disclaims any liability arising out of your use of the Documentation. Xilinx reserves

the right, at its sole discretion, to change the Documentation without notice at any time. Xilinx assumes no obligation to correct any errors

contained in the Documentation, or to advise you of any corrections or updates. Xilinx expressly disclaims any liability in connection with

technical support or assistance that may be provided to you in connection with the Information.

THE DOCUMENTATION IS DISCLOSED TO YOU “AS-IS” WITH NO WARRANTY OF ANY KIND. XILINX MAKES NO OTHER

WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY, REGARDING THE DOCUMENTATION, INCLUDING ANY

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY

RIGHTS. IN NO EVENT WILL XILINX BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, EXEMPLARY, SPECIAL, OR INCIDENTAL

DAMAGES, INCLUDING ANY LOSS OF DATA OR LOST PROFITS, ARISING FROM YOUR USE OF THE DOCUMENTATION.

United States and other countries. All other trademarks are the property of their respective owners.

UG518 (v1.1) August 19, 2009 www.xilinx.com SP601 Hardware User Guide

Revision History

The following table shows the revision history for this document.

Date Version Revision

07/15/2009 1.0 Initial Xilinx release.

08/19/2009 1.1 • Added Appendix C, “VITA 57.1 FMC Connections.”

• Updated Figure 1-18 and Figure 1-32.

• Updated Table 1-4, Table 1-17, and Table 1-20.

• Added introductory paragraph to Appendix D, “SP601 Master UCF.”

• Miscellaneous typographical edits and new user guide template.

SP601 Hardware User Guide www.xilinx.com UG518 (v1.1) August 19, 2009

SP601 Hardware User Guide www.xilinx.com 5

UG518 (v1.1) August 19, 2009

Preface: About This Guide

Guide Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Typographical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Online Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 1: SP601 Evaluation Board

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Related Xilinx Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1. Spartan-6 XC6SLX16-2CSG324 FPGA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

I/O Voltage Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2. 128 MB DDR2 Component Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3. SPI x4 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4. Linear Flash BPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5. 10/100/1000 Tri-Speed Ethernet PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6. USB-to-UART Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7. IIC Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8-Kb NV Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8. Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Oscillator (Differential) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Oscillator Socket (Single-Ended, 2.5V or 3.3V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

SMA Connectors (Differential) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9. VITA 57.1 FMC-LPC Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

10. Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

11. FPGA Awake LED and Suspend Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

12. FPGA INIT and DONE LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

13. User I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

14. FPGA_PROG_B Pushbutton Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

AC Adapter and 5V Input Power Jack/Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Onboard Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

JTAG Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table of Contents

6 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Appendix A: References

Appendix B: Default Jumper and Switch Settings

Appendix C: VITA 57.1 FMC Connections

Appendix D: SP601 Master UCF

SP601 Hardware User Guide www.xilinx.com 7

UG518 (v1.1) August 19, 2009

Preface

About This Guide

This manual accompanies the Spartan®-6 FPGA SP601 Evaluation Board and contains

information about the SP601 hardware and software tools.

Guide Contents

This manual contains the following chapters:

• Chapter 1, “SP601 Evaluation Board,” provides an overview of the embedded

development board and details the components and features of the SP601 board.

• Appendix A, “References.”

• Appendix B, “Default Jumper and Switch Settings.”

• Appendix D, “SP601 Master UCF.”

Additional Resources

To search the database of silicon and software questions and answers, or to create a

technical support case in WebCase, see the Xilinx website at:

http://www.xilinx.com/support

.

Conventions

This document uses the following conventions. An example illustrates each convention.

Typographical

The following typographical conventions are used in this document:

Convention Meaning or Use Example

Courier font

Messages, prompts, and

program files that the system

displays

speed grade: - 100

Courier bold

Literal commands that you enter

in a syntactical statement

ngdbuild design_name

Helvetica bold

Commands that you select from

a menu

File → Open

Keyboard shortcuts Ctrl+C

8 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Preface: About This Guide

Online Document

The following conventions are used in this document:

Italic font

Variables in a syntax statement

for which you must supply

values

ngdbuild design_name

References to other manuals

See the User Guide for more

information.

Emphasis in text

If a wire is drawn so that it

overlaps the pin of a symbol, the

two nets are not connected.

Dark Shading

Items that are not supported or

reserved

This feature is not supported

Square brackets [ ]

An optional entry or parameter.

However, in bus specifications,

such as bus[7:0], they are

required.

ngdbuild [option_name]

design_name

Braces { }

A list of items from which you

must choose one or more

lowpwr ={on|off}

Vertical bar |

Separates items in a list of

choices

lowpwr ={on|off}

Angle brackets < >

User-defined variable or in code

samples

Vertical ellipsis

.

Repetitive material that has

been omitted

IOB #1: Name = QOUT’

IOB #2: Name = CLKIN’

.

Horizontal ellipsis . . .

Repetitive material that has

been omitted

allow block block_name loc1

loc2 ... locn;

Notations

The prefix ‘0x’ or the suffix ‘h’

indicate hexadecimal notation

A read of address 0x00112975

returned 45524943h.

An ‘_n’ means the signal is

active low

usr_teof_n

is active low.

Convention Meaning or Use Example

Blue text

Cross-reference link to a location

in the current document

See the section “Additional

Resources” for details.

Refer to “Title Formats” in

Chapter 1 for details.

Blue, underlined text

Hyperlink to a website (URL)

Go to http://www.xilinx.com

for the latest speed files.

SP601 Hardware User Guide www.xilinx.com 9

UG518 (v1.1) August 19, 2009

Chapter 1

SP601 Evaluation Board

Overview

The SP601 board enables hardware and software developers to create or evaluate designs

targeting the Spartan®-6 XC6SLX16-2CSG324 FPGA.

The SP601 provides board features for evaluating the Spartan-6 family that are common to

most entry-level development environments. Some commonly used features include a

DDR2 memory controller, a parallel linear flash, a tri-mode Ethernet PHY, general-

purpose I/O (GPIO), and a UART. Additional functionality can be added through the

VITA 57.1.1 expansion connector. “Features,” page 10 provides a general listing of the

board features with details provided in “Detailed Description,” page 12.

Additional Information

Additional information and support material is located at:

• http://www.xilinx.com/sp601

This information includes:

• Current version of this user guide in PDF format

• Example design files for demonstration of Spartan-6 FPGA features and technology

• Demonstration hardware and software configuration files for the SP601 linear and SPI

memory devices

• Reference Design Files

• Schematics in PDF format and DxDesigner schematic format

• Bill of materials (BOM)

• Printed-circuit board (PCB) layout in Allegro PCB format

• Gerber files for the PCB (Many free or shareware Gerber file viewers are available on

the internet for viewing and printing these files.)

• Additional documentation, errata, frequently asked questions, and the latest news

For information about the Spartan-6 family of FPGA devices, including product

highlights, data sheets, user guides, and application notes, see the Spartan-6 FPGA website

at http://www.xilinx.com/support/documentation/spartan-6.htm

.

10 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Chapter 1: SP601 Evaluation Board

Features

The SP601 board provides the following features:

• 1. Spartan-6 XC6SLX16-2CSG324 FPGA

• 2. 128 MB DDR2 Component Memory

• 3. SPI x4 Flash

• 4. Linear Flash BPI

• 5. 10/100/1000 Tri-Speed Ethernet PHY

• 7. IIC Bus

♦ 8Kb NV memory

♦ External access 2-pin header

♦ VITA 57.1 FMC-LPC connector

• 8. Clock Generation

♦ Oscillator (Differential)

♦ Oscillator Socket (Single-Ended, 2.5V or 3.3V)

• SMA Connectors (Differential)

• 9. VITA 57.1 FMC-LPC Connector

• 10. Status LEDs

♦ FPGA_AWAKE

♦ INIT

♦ DONE

• 13. User I/O

♦ User LEDs

♦ User DIP switch

♦ User pushbuttons

♦ GPIO male pin header

• 14. FPGA_PROG_B Pushbutton Switch

• Configuration Options

♦ 3. SPI x4 Flash (both onboard and off-board)

♦ 4. Linear Flash BPI

♦ JTAG Configuration

• Power Management - AC Adapter and 5V Input Power Jack/Switch, Onboard Power

Supplies

SP601 Hardware User Guide www.xilinx.com 11

UG518 (v1.1) August 19, 2009

Related Xilinx Documents

Prior to using the SP601 Evaluation Board, users should be familiar with Xilinx resources.

See the following locations for additional documentation on Xilinx tools and solutions:

• ISE: www.xilinx.com/ise

• Answer Browser: www.xilinx.com/support

• Intellectual Property: www.xilinx.com/ipcenter

X-Ref Target - Figure 1-1

Figure 1-1: SP601 Features and Banking

LEDs

DIP Switch

GPIO Header

FMC LPC

Expansion Connector

10/100/1000

Ethernet GMII

Spartan-6

XC6SLX16

U1

Parallel Flash

USB

JTAG Connector

Pushbuttons

DDR2

Differential Clock

Clock Socket

SMA Clock

IIC EEPROM

and Header

MODE

DIP Switch

SPI x4 or

External Config

USB UART

UG518_01_070809

DED

Bank 0

2.5 V

Bank 3

1.8V

Bank 1

2.5V

Bank 2

2.5V

12 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Chapter 1: SP601 Evaluation Board

Detailed Description

Figure 1-2 shows a board photo with numbered features corresponding to Table 1-1 and

the section headings in this document.

The numbered features in Figure 1-2 correlate to the features and notes listed in Table 1-1.

X-Ref Target - Figure 1-2

Figure 1-2: SP601 Board Photo

11

77

22

33

44

55

66

88

99

1010

1212

1313

1414

1515

88

1616

1111

1313

Table 1-1: SP601 Features

Number Feature Notes

Schematic

Page

1 Spartan-6 FPGA XC6SLX16-2CSG324

2 DDR2 Component Hard memory controller w/ OCT 5

3 SPI x4 Flash and Headers SPI select and External Headers 8

4 Linear Flash BPI StrataFlash 8-bit (J3 device), 3 pins

shared w/ SPI x4

8

5 10/100/1000 Ethernet PHY GMII Marvell Alaska PHY 7

6 RS232 UART (USB Bridge) Uses CP2103 Serial-to-USB connection 10

7 IIC Goes to Header and VITA 57.1 FMC 10

8 Clock, socket, SMA Differential, Single-Ended, Differential 9

SP601 Hardware User Guide www.xilinx.com 13

UG518 (v1.1) August 19, 2009

Detailed Description

1. Spartan-6 XC6SLX16-2CSG324 FPGA

A Xilinx Spartan-6 XC6SLX16-2CSG324 FPGA is installed on the Embedded Development

Board.

Configuration

The SP601 supports configuration in the following modes:

• Master SPI x4

• Master SPI x4 with off-board device

• BPI

• JTAG (using the included USB-A to Mini-B cable)

For details on configuring the FPGA, see “Configuration Options.”

I/O Voltage Rails

There are four available banks on the LX16-CS324 device. Banks 0, 1, and 2 are connected

for 2.5V I/O. Bank 3 is used for the 1.8V DDR2 component memory interface of Spartan-6

FPGA’s hard memory controller. The voltage applied to the FPGA I/O banks used by the

SP601 board is summarized in Table 1-2.

9 VITA 57.1 FMC-LPC

connector

LVDS signals, clocks, PRSNT 6

10 LEDs Ethernet PHY Status 7

11 LED, Header FPGA Awake LED, Suspend Header 8

12 LEDs FPGA INIT, DONE 9

13

LED User I/O (active-High) 9

DIP Switch User I/O (active-High) 9

Pushbutton User I/O, CPU_RESET (active-High) 9

12-pin (8 I/O) Header 6 pins x 2 male header with 8 I/Os

(active-High)

10

14 Pushbutton FPGA_PROG_B 9

15 USB JTAG Cypress USB to JTAG download cable

logic

14, 15

16 Onboard Power Power Management 11,12,13

Table 1-1: SP601 Features (Cont’d)

Number Feature Notes

Schematic

Page

Table 1-2: I/O Voltage Rail of FPGA Banks

FPGA Bank I/O Voltage Rail

02.5V

12.5V

14 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Chapter 1: SP601 Evaluation Board

References

See the Xilinx Spartan-6 FPGA documentation for more information at

http://www.xilinx.com/support/documentation/spartan-6.htm

.

2. 128 MB DDR2 Component Memory

There are 128 MB of DDR2 memory available on the SP601 board. A 1-Gb Elpida

EDE1116ACBG (84-ball) DDR2 memory component is accessible through Bank 3 of the

LX16 device. The Spartan-6 FPGA hard memory controller is used for data transfer across

the DDR2 memory interface's 16-bit data path using SSTL18 signaling. The maximum data

rate supported is 800 Mb/s with a memory clock running at 400 MHz. Signal integrity is

maintained through DDR2 resistor terminations and memory on-die terminations (ODT),

as shown in Table 1-3 and Table 1-4.

22.5V

31.8V

Table 1-2: I/O Voltage Rail of FPGA Banks (Cont’d)

FPGA Bank I/O Voltage Rail

Table 1-3: Termination Resistor Requirements

Signal Name Board Termination On-Die Termination

DDR2_A[14:0] 49.9 ohms to V

TT

DDR2_BA[2:0] 49.9 ohms to V

TT

DDR2_RAS_N 49.9 ohms to V

TT

DDR2_CAS_N 49.9 ohms to V

TT

DDR2_WE_N 49.9 ohms to V

TT

DDR2_CS_N 100 ohms to GND

DDR2_CKE 4.7K ohms to GND

DDR2_ODT 4.7K ohms to GND

DDR2_DQ[15:0] ODT

DDR2_UDQS[P,N],

DDR2_LDQS[P,N]

ODT

DDR2_UDM, DDR2_LDM ODT

DDR2_CK[P,N]

100 ohm differential at

memory component

Notes:

1. Nominal value of V

TT

for DDR2 interface is 0.9V.

Table 1-4: FPGA On-Chip (OCT) Termination External Resistor Requirements

FPGA U1 Pin FPGA Pin Number Board Connection for OCT

ZIO L6 No Connect

RZQ C2 100 ohms to GROUND

SP601 Hardware User Guide www.xilinx.com 15

UG518 (v1.1) August 19, 2009

Detailed Description

Table 1-5 shows the connections and pin numbers for the DDR2 Component Memory.

Table 1-5: DDR2 Component Memory Connections

FPGA U1 Schematic Netname

Memory U2

Pin Number Name

J7 DDR2_A0 M8 A0

J6 DDR2_A1 M3 A1

H5 DDR2_A2 M7 A2

L7 DDR2_A3 N2 A3

F3 DDR2_A4 N8 A4

H4 DDR2_A5 N3 A5

H3 DDR2_A6 N7 A6

H6 DDR2_A7 P2 A7

D2 DDR2_A8 P8 A8

D1 DDR2_A9 P3 A9

F4 DDR2_A10 M2 A10

D3 DDR2_A11 P7 A11

G6 DDR2_A12 R2 A12

L2 DDR2_DQ0 G8 DQ0

L1 DDR2_DQ1 G2 DQ1

K2 DDR2_DQ2 H7 DQ2

K1 DDR2_DQ3 H3 DQ3

H2 DDR2_DQ4 H1 DQ4

H1 DDR2_DQ5 H9 DQ5

J3 DDR2_DQ6 F1 DQ6

J1 DDR2_DQ7 F9 DQ7

M3 DDR2_DQ8 C8 DQ8

M1 DDR2_DQ9 C2 DQ9

N2 DDR2_DQ10 D7 DQ10

N1 DDR2_DQ11 D3 DQ11

T2 DDR2_DQ12 D1 DQ12

T1 DDR2_DQ13 D9 DQ13

U2 DDR2_DQ14 B1 DQ14

U1 DDR2_DQ15 B9 DQ15

16 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Chapter 1: SP601 Evaluation Board

Figure 1-3 provides the user constraints file (UCF) for the DDR2 SDRAM address pins,

including the I/O pin assignment and the I/O standard used.

F2 DDR2_BA0 L2 BA0

F1 DDR2_BA1 L3 BA1

E1 DDR2_BA2 L1 BA2

E3 DDR2_WE_B K3 WE

L5 DDR2_RAS_B K7 RAS

K5 DDR2_CAS_B L7 CAS

K6 DDR2_ODT K9 ODT

G3 DDR2_CLK_P J8 CK

G1 DDR2_CLK_N K8 CK

H7 DDR2_CKE K2 CKE

L4 DDR2_LDQS_P F7 LDQS

L3 DDR2_LDQS_N E8 LDQS

P2 DDR2_UDQS_P B7 UDQS

P1 DDR2_UDQS_N A8 UDQS

K3 DDR2_LDM F3 LDM

K4 DDR2_UDM B3 UDM

X-Ref Target - Figure 1-3

NET "DDR2_A12" LOC ="G6";| IOSTANDARD = SSTL18_II ;

NET "DDR2_A11" LOC ="D3";| IOSTANDARD = SSTL18_II ;

NET "DDR2_A10" LOC ="F4";| IOSTANDARD = SSTL18_II ;

NET "DDR2_A9" LOC ="D1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A8" LOC ="D2"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A7" LOC ="H6"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A6" LOC ="H3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A5" LOC ="H4"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A4" LOC ="F3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A3" LOC ="L7"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A2" LOC ="H5"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A1" LOC ="J6"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_A0" LOC ="J7"; | IOSTANDARD = SSTL18_II ;

Figure 1-3: UCF Location Constraints for DDR2 SDRAM Address Inputs

Table 1-5: DDR2 Component Memory Connections (Cont’d)

FPGA U1 Schematic Netname

Memory U2

Pin Number Name

SP601 Hardware User Guide www.xilinx.com 17

UG518 (v1.1) August 19, 2009

Detailed Description

Figure 1-4 provides the UCF constraints for the DDR2 SDRAM data pins, including the

I/O pin assignment and I/O standard used.

Figure 1-5 provides the UCF constraints for the DDR2 SDRAM control pins, including the

I/O pin assignment and the I/O standard used.

References

See the Elpida DDR2 specifications for more information at

http://www.elpida.com/en/products/details/EDE1116ACBG.html

.

Also, see the Spartan-6 FPGA embedded hard memory controller block user guide at

http://www.xilinx.com/support/documentation/user_guides/ug388.pdf

.

X-Ref Target - Figure 1-4

NET "DDR2_DQ15" LOC ="U1";| IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ14" LOC ="U2";| IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ13" LOC ="T1";| IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ12" LOC ="T2";| IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ11" LOC ="N1";| IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ10" LOC ="N2";| IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ9" LOC ="M1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ8" LOC ="M3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ7" LOC ="J1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ6" LOC ="J3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ5" LOC ="H1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ4" LOC ="H2"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ3" LOC ="K1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ2" LOC ="K2"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ1" LOC ="L1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_DQ0" LOC ="L2"; | IOSTANDARD = SSTL18_II ;

Figure 1-4: UCF Location Constraints for DDR2 SDRAM Data I/O Pins

X-Ref Target - Figure 1-5

NET "DDR2_WE_B" LOC ="E3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_UDQS_P" LOC ="P2";| IOSTANDARD = SSTL18_II ;

NET "DDR2_UDQS_N" LOC ="P1";| IOSTANDARD = SSTL18_II ;

NET "DDR2_UDM" LOC ="K4"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_RAS_B" LOC ="L5"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_ODT" LOC ="K6"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_LDQS_P" LOC ="L4";| IOSTANDARD = SSTL18_II ;

NET "DDR2_LDQS_N" LOC ="L3";| IOSTANDARD = SSTL18_II ;

NET "DDR2_LDM" LOC ="K3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_CLK_P" LOC ="G3"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_CLK_N" LOC ="G1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_CKE" LOC ="H7"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_CAS_B" LOC ="K5"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_BA2" LOC ="E1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_BA1" LOC ="F1"; | IOSTANDARD = SSTL18_II ;

NET "DDR2_BA0" LOC ="F2"; | IOSTANDARD = SSTL18_II ;

Figure 1-5: UCF Location Constraints for DDR2 SDRAM Control Pins

18 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Chapter 1: SP601 Evaluation Board

3. SPI x4 Flash

The Xilinx Spartan-6 FPGA hosts a SPI interface which is visible to the Xilinx iMPACT

configuration tool. The SPI memory device operates at 3.0V; the Spartan-6 FPGA I/Os are

3.3V tolerant and provide electrically compatible logic levels to directly access the SPI flash

through a 2.5V bank. The XC6SLX16-2CSG324 is a master device when accessing an

external SPI flash memory device.

The SP601 SPI interface has two parallel connected configuration options (see Figure 1-7):

an SPI X4 (Winbond W25Q64VSFIG) 64-Mb flash memory device and a flash

programming header (J12). J12 supports a user-defined SPI mezzanine board. The SPI

configuration source is selected via SPI select jumper J15. For details on configuring the

FPGA, see “Configuration Options.”

X-Ref Target - Figure 1-6

Figure 1-6: J12 SPI Flash Programming Header

FPGA_D1_MISO2

J12

1

2

3

4

5

6

7

8

9

FPGA_D2_MISO3

FPGA_PROG_B

FPGA_MOSI_CSI_B_MISO0

SPI_CS_B

FPGA_CCLK

FPGA_D0_DIN_MISO_MISO1

UG518_06_070809

GND

VCC3V3

Silkscreen

TMS

TDI

TDO

TCK

GND

3V3

HDR_1X9

SP601 Hardware User Guide www.xilinx.com 19

UG518 (v1.1) August 19, 2009

Detailed Description

X-Ref Target - Figure 1-7

Figure 1-7: SPI Flash Interface Topology

Table 1-6: SPI x4 Memory Connections

FPGA U1

Schematic Netname

SPI MEM U17 SPI HDR J12

Pin # Pin Name Pin # Pin Name

V2 FPGA_PROG_B 1

V14 FPGA_D2_MISO3 1 IO3_HOLD_B 2

T14 FPGA_D1_MISO2_R 9 IO2_WP_B 3

V3 SPI_CS_B 4 TMS

T13 FPGA_MOSI_CSI_B_MISO0 15 DIN 5 TDI

R13 FPGA_D0_DIN_MISO_MISO1 8 IO1_DOUT 6 TDO

R15 FPGA_CCLK 16 CLK 7 TCK

8GND

9 VCC3V3

J15.2 SPIX4_CS_B 7 CS_B

U1

FPGA SPI INTERFACE

U17

J12

SPI X4

FLASH

MEMORY

WINBOND

W25Q64VSFIG

SPI PROGRAM

HEADER

SPI SELECT

JUMPER

ON = SPI X4 U17

OFF = SPI EXT. J12

SPIX4_CS_B

DIN,DOUT,CCLK

SPI_CS_B

2

J15

1

UG518_07_070809

20 www.xilinx.com SP601 Hardware User Guide

UG518 (v1.1) August 19, 2009

Chapter 1: SP601 Evaluation Board

Figure 1-8 provides the UCF constraints for the SPI serial flash PROM.

References

See the Winbond Serial Flash specifications for more information at http://www.winbond-

usa.com/hq/enu/ProductAndSales/ProductLines/FlashMemory/SerialFlash/W25X64.htm.

See the XPS Serial Peripheral Interface specification for more information at

http://www.xilinx.com/support/documentation/ip_documentation/xps_spi.pdf

.

4. Linear Flash BPI

An 8-bit (16 MB) Numonyx linear flash memory (TE 28F128J3D-75) (J3D type) is used to

provide non-volatile bitstream, code, and data storage. The J3D devices operate at 3.0V; the

Spartan-6 FPGA I/Os are 3.3V tolerant and provide electrically compatible logic levels to

directly access the linear flash BPI through a 2.5V bank. For details on configuring the

FPGA, see “Configuration Options.”

X-Ref Target - Figure 1-8

NET "FPGA_D2_MISO3" LOC = "V14";

NET "SPI_CS_B" LOC = "V3";

NET "FPGA_D0_DIN_MISO_MISO1" LOC = "R13";

NET "FPGA_D1_MISO2" LOC = "T14";

NET "FPGA_MOSI_CSI_B_MISO0" LOC = "T13";

NET "FPGA_CCLK" LOC = "R15";

Figure 1-8: UCF Location Constraints for BPI Flash Connections

X-Ref Target - Figure 1-9

Figure 1-9: Linear Flash BPI Interface

Table 1-7: BPI Memory Connections

FPGA U1 Pin Schematic Netname

BPI Memory U10

Pin Number Pin

K18 FLASH_A0 32 A0

K17 FLASH_A1 28 A1

J18 FLASH_A2 27 A2

J16 FLASH_A3 26 A3

G18 FLASH_A4 25 A4

G16 FLASH_A5 24 A5

U1 U10

FPGA

BPI FLASH

INTERFACE

NUMONYX TYPE J3vD

T28F128J3D-75

ADDR, DATA, CTRL

UG518_09_070809

Page is loading ...

Xilinx SP601 User manual

This manual is also suitable for

Xilinx SP601 User manual

Related papers

Other documents