Reznor JT4BE Installation guide

JT4BE
Reznor
Brand
Reznor
Model
JT4BE
Type
Installation guide

Sure, here is a brief product information for the Reznor JT4BE in up to 500 characters:

Reznor JT4BE:

The Reznor JT4BE is a powerful and efficient forced-air heater that provides reliable warmth for large spaces such as warehouses, garages, and workshops. With its heavy-duty construction and durable components, it's built to withstand harsh conditions and deliver long-lasting performance. The JT4BE features adjustable heat output, allowing you to customize the temperature to your liking.

Sure, here is a brief product information for the Reznor JT4BE in up to 500 characters:

Reznor JT4BE:

The Reznor JT4BE is a powerful and efficient forced-air heater that provides reliable warmth for large spaces such as warehouses, garages, and workshops. With its heavy-duty construction and durable components, it's built to withstand harsh conditions and deliver long-lasting performance. The JT4BE features adjustable heat output, allowing you to customize the temperature to your liking.

Installation Instructions
Snow Stand Kit
Unit Installation on Snowstand
Assembled Snowstand
INTRODUCTION
This Snowbase Kit contains four (4) Legs, four (4) Side Braces, and one (1) cross Center Brace, all made
out of sheet metal and painted black. The purpose of this kit is to elevate the outdoor condensing heat
pump unit off the ground to allow unrestricted air flow thru the coil. When assembled in accordance with
these installation instructions, the assembly will support the weight of the condensing unit and lock it into
place to restrict movement from side to side.
2
This Kit Includes:
a. Installation Instructions – 709062
b. Four (4) Legs – Part Number 664553
c. Four (4) Side Braces – Part Number 664554
d. One (1) Center Braces – Part Number 664555
e. Twenty (20) Black Screws – Part Number 600442
LEG,SNOWBASE
BRACE,SIDE,
SNOWBASE
BRACE,CENTER,
SNOWBASE
ASSEMBLY INSTRUCTIONS
1. Stand one Leg on its end and line up the holes with
the holes at the end of one of the Side Braces. In-
sert the tabs on the sides of the Legs into the slots
in the Side Braces. Using a screw gun with either
a 5/16” hex bit or a flat head screwdriver bit, drive
one screw per hole through the Leg and into the
Side Brace.
2. Using the same method as in Step 1, attach an-
other Side Brace to the second set of holes on the
Leg.
3. Repeat Steps 1 and 2, making your way around the assembly, until you have reached the last Leg. Do not at-
tach the last Leg until the Center Brace is in place.
4. Slide the center Brace into the opposite Leg from the last Leg. Insert the tabs on the ends of the Center Brace
into the remaining slots in the back side of the Side Braces. Also make sure the top of the Center Brace slides
under the tabs on the top of the Legs.
INSTALLER: PLEASE LEAVE THESE INSTALLATION
INSTRUCTIONS WITH THE HOMEOWNER.
5. Slide the opposite end tabs of the Center Brace into
the opposite Legs. Drive two screws into the top
the Center Brace and through the holes in the top
flange of the legs.
6. Position the fourth Leg into place, making sure the
tabs of the Leg have slid into the slots in the Side
Braces. Once in place, drive four screws into their
respective side holes of the Leg.
UNIT INSTALLATION
1. Locate the Snowbase where the final installation of
the condensing unit will be. Orient the Snowbase
so that the valve corner of the condensing unit,
when installed, will not sit on the Center Brace.
2. Lift the condensing unit to a level height above the
Snowbase.
3. Position the condensing unit over the Snowbase.
Lower the unit so that the tabs on the top of the
Snowbase fit into the grooves on the underside of
the composite base pan on the condensing unit. It
will be fully installed when the unit will not rotate
more than five degrees.
Underside of
Basepan
Ta b
709062B (Replaces 709062A)
Specifications & illustrations subject to change
without notice or incurring obligations (02/14).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Reznor JT4BE Installation guide

JT4BE
Reznor
Brand
Reznor
Model
JT4BE
Type
Installation guide

Sure, here is a brief product information for the Reznor JT4BE in up to 500 characters:

Reznor JT4BE:

The Reznor JT4BE is a powerful and efficient forced-air heater that provides reliable warmth for large spaces such as warehouses, garages, and workshops. With its heavy-duty construction and durable components, it's built to withstand harsh conditions and deliver long-lasting performance. The JT4BE features adjustable heat output, allowing you to customize the temperature to your liking.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents