Lenco BTL-450 Owner's manual

Model BTL-450

User manual Bluetooth® Tower Speaker

Gebruiksaanwijzing Bluetooth® Tower Speaker

Benutzerhandbuch Bluetooth® Turmlautsprecher

Mode d’emploi Enceinte Tour Bluetooth®

Manual del usuario Altavoz de Torre Bluetooth®

Page is loading ...

3

English

1. Safety Precautions

The purpose of these precautions is to ensure user safety and prevent property damage. Be sure to

read and observe all safety precautions.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle is intended

to alert the user to the presence of un-insulated “dangerous voltage” enclosed

within the productthat may be of sufficient magnitude to constitute a risk of electric

shock to the person using the device.

The exclamation mark within an equilateral triangle is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in

the instruction manual accompanying the appliance.

1. Read, keep and follow these instructions carefully.

2. The appliance is only for domestic use and not for commercial use.

3. Please check that the voltage on the type plate of your appliance corresponds with your house

electricity supply (type plate is located on the back of the unit).

4. Do not use this apparatus near water.

5. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s

instructions.

6. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices

(including amplifiers) that produce heat.

7. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong is provided for your safety. When the

provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet. (For UK only)

8. Protect the power cord from being walked on or pinched, particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

9. Only use attachments/accessories specified by the manufacturer.

10. Unplug this apparatus during lightning storms or when unused for long periods of time.

11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as the power supply cord or the plug, when liquid has been

spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

12. Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or

electric shock.

4

13. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such

as vases, shall be placed on the apparatus.

14. Do not let children play with the product.

15. Do not store the product in extremely cold or warm environments.

16. The appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instructions concerning the use of the appliance by a person responsible

for their safety.

2. Getting Started

- Read this instruction manual carefully.

- Remove the equipment from the box.

- Remove the packaging and save it for future use (for example when moving the unit).

3. Features

- Two main speakers

- Bluetooth® Connectivity

- Aux Jack Included

- 3.5mm Aux Cable Included

- USB Port for charging (5V, 1A)

- USB Port for playing MP3

- SD card slot for playing MP3

- FM radio

- LED display

- One built-in Subwoofer

- LED Pulse light in whole front which blink with the music (light with 7 single colors and 3

modes)

4. Box Content

- Speaker Body

- Speaker Base

- Screw (1 pc)

- Metal washer (1 pc)

- 3.5 mm Line-in Cable

- Remote Control

- Instruction Manual

5

5. Description of Parts

5.1 Top panel

No.

Description

1.

Support Bracket

2.

LED Display

3.

Standby Button: Press to turn the speaker on and off

4.

Source Button: Press to switch between FM mode, USB mode (for both USB and SD playing), Aux-in

mode and Bluetooth mode.

5.

Skip Backward: Press to skip to previous track / long press to FM stations down searching.

6.

Play/Pause/Pairing: Press to play or pause and long press to start the pairing mode with Bluetooth.

When in USB mode, a long press around 3 seconds can swap between USB and SD playing when both

devices are inserted into the unit.

7.

Skip Forward: Press to skip to next track / long press to FM stations up searching.

8.

Volume - : Press to decrease the volume.

9.

Volume + : Press to increase the volume.

6

5.2 Remote control

No.

Description

1.

Standby Button (Power on/off)

2.

Source Button: Press to switch between FM, Bluetooth, AUX-in and USB/SD Card Mode.

3.

Mute Button

4.

OFF/ON (For LED light only)

5.

Mode: switch the mode for the LED light’s mode only. There are three modes in Spectrum Mode, Level

Mode and Wall Lamp Mode

6.

Colour Style: Switch the LED colour only: Color 00 in random color, Color 01 in Red, Color 02 in green,

Color 03 in Blue, Color 04 in purple, Color 05 in light yellow, Color 06 in light blue, Color 07 in white,

Color 08 in random color flash circularly.

7.

Skip Backward Button

8.

Play/Pause/Pairing Button

9.

Skip Forward Button

10.

Scan/Memory Button: Short press for memory, long press for scan and save

11.

CH -

12.

CH +

13.

Bass+ Effect Button

14.

Bass- Effect Button

15.

Treb+ Effect Button

16.

Treb- Effect Button

17.

Volume+ Button

18.

Volume- Button

7

6. Using the Remote Control to Operate the Unit

Aim the remote control directly at the remote control sensor (IR) on the front panel. Don’t put any

objects between the remote control and the system while operating the unit.

7. Batteries

7.1 Installing Batteries

1. Slide out the battery holder from the remote control case. (Push tab "A" towards the middle

first, see diagram).

2. Place one 3V CR2025 (Lithium) battery into the battery holder, observing the polar marking. If

the battery is placed incorrectly, the remote control will not work. Dispose of the old battery

properly. Do not leave it lying around where a child or pet could play with it or swallow it.

3. The battery may explode or leak if it is mistreated. Do not attempt to recharge it or disassemble

it. Do not dispose of the old battery in a fire.

4. Insert the battery holder into the battery compartment.

NOTE: Please remove all the batteries to prevent damage or injury from battery leakage if the unit

will not be used for a long period of time. Use only the specified size and type of battery.

7.2 Battery Safety

Always:

- Ensure the battery compartment is secured.

- Only use the batteries recommended.

- Ensure a correct fit of the batteries. Observe the plus and minus marks on both the battery

and the compartment.

- Replace a full set of batteries at one time.

- Store unused batteries in their packaging and keep away from metal objects that may cause

a short circuit.

- Remove dead batteries from the equipment.

- Remove batteries from the remote control if it is not to be used for a long time.

- Remember to keep button cells and batteries away from children as they can easily be

swallowed.

- Seek medical attention immediately if batteries are swallowed.

8

Never:

- Dispose of batteries in a fire.

- Attempt to recharge ordinary batteries.

8. Set Up

1. Take out the speaker body and speaker base carefully from the box.

2. Take out the accessories (1 pc of screw and 1 pc of metal washer).

3. Fit the base with the body with 1 hole.

4. Screw the base into the body by using a proper screwdriver with the screw and washer.

5. Place the speaker in a standing position on the floor and it's ready to use.

9

9. Functions

9.1 Bluetooth Pairing

1. Power on the unit, press “SOURCE” on the top panel or the button “SOURCE” on the remote

control to switch to the Bluetooth mode, the LED will indicate “ BT ”.and the LED icon“ ”

will start blinking after 3-5 seconds; this means the speaker unit is ready for the Pairing mode.

2. Turn on Bluetooth in your smartphone/tablet , and ensure it at “SEARCHING DEVICE” mode ,

Found “Lenco BTL-450” and select.

3. Once the unit is found, enter password 0000 to connect with smart phone/tablet (some devices

may not need password).

4. The LED icon“ ” will light up and you will hear “DU” sound , if the connection was a success.

5. If the smartphone/tablet cannot find the unit or can’t pair, please power on again and repeat

the above steps.

6. It will auto reconnect the previous paired device when it enters into Bluetooth mode. If the unit

doesn’t auto connect with the previous paired device, please restart the Bluetooth in the

smartphone/tablet and then follow the above steps to finish the connection.

7. You can manually turn of Bluetooth for your smartphone/tablet; Bluetooth connection will also

be canceled in case the smartphone/tablet is too far away from the speaker (over 10m). in this

latter case, the unit will go back to Bluetooth standby mode.

8. To reconnect, please ensure that Bluetooth on your smartphone is set at the ‘searching device’

mode. Keep pressing ‘pairing’ until you find the Lenco BTL-450 again, and follow the above

steps.

9.2 AUX-IN (Line in Type)

Requires a 3.5 mm cable (included).

1. Connect a 3.5 mm cable to the Aux-in jack. Connect the other end of the 3.5 mm cable to an

MP3 player or other audio source.

2. Press the “STANDBY” button to turn the unit on.

3. Press the “SOURCE” button on the top panel or the “SOURCE” button on the remote to switch

to Aux-in mode.

4. Use the controls on the connected device to begin playing audio routed through the unit.

9.3 USB port for charging

USB power output DC 5V 1A. It supports charging all devices in the power range.

When charging a device, ensure that the power supply is the right one for your device.

9.4 USB port for playing MP3

Power on the unit and insert a USB Flash Drive (not supplied) into the USB Port, ensuring the plug is

fully inserted in the correct way.

The tower will play music from the USB automatically. The maximum size of the Flash Drive that can

be supported is up to 32GB.

9.5 SD card slot for playing MP3

Insert an SD card (not supplied) into the memory card expansion slot. Make sure it is inserted in the

correct way.

The tower will play music from the SD card automatically. The maximum size of the Flash Drive that

can be supported is up to 32GB.

10

REMARK: When both USB and SD card are inserted, pressing the play button for a long time can

swap between USB and SD card.

9.6 Playing the FM radio

1. Press the "STANDBY" button to turn the unit on.

2. Ensure that the FM Antenna has been fully extended and press "SOURCE" on the top panel or

the “SOURCE” button on the remote control to adjust to the "FM" mode.

3. Press “Skip forward” or “Skip backward” and hold; the unit will scan the radio station, and stop

once it has found one.

4. For fine tuning 0.1MHz, press the “Skip Forward or Skip Backward” button once.

9.7 Programming & Playing of FM radio presets

1. Follow the steps for Playing the FM Radio.

2. Press the "Scan" button for a long time on the remote to search and preset stations in memory

(i.e. “P01” – this will blink on the display - and then the preset station frequency number will be

shown on the display).

3. Note: 30 FM stations can be preset.

4. To play the preset Radio Stations, press the "CH-" or "CH+" buttons to cycle through the preset

FM radio stations.

9.8 Manual FM station save

1. When under FM mode, press the Skip backward /Skip forward button to choose the

station.

2. Press the Scan/Memory button shortly; “P 00” will blink on the display which means

you enter into the manual saving state, and then Press the "CH-" or "CH+" buttons to cycle

through the preset FM radio stations.

3. Press Scan/Memory button to finish manual saving.

10. Cleaning the Appliance

Disconnect the appliance from the power source when cleaning.

If the unit becomes dusty, wipe it with a soft and dry duster. Use a soft cloth to clean this appliance.

Do not use any wax, polish sprays, or abrasive cleaners on the unit.

The normal function of the product may be disturbed by strong Electro-Magnetic Interference. If so,

simply reset the product to resume normal operation by following the instruction manual. In case

the functions could not resume, please use the product in another location.

Care and maintenance specifications

1. Always disconnect the equipment from the power supply

before cleaning.

2. Clean the equipment with a soft, damp, lint free cloth.

3. Do not use abrasives or harsh cleaners.

11

11. Trouble Shooting

Problem

Remedy

Power

System does not turn on or

does not respond to the

remote control.

-Make sure the AC power plug is connected to the wall socket

outlet properly and that it has power.

-If this does not help, leave the unit unplugged before seeking

advice.

Remote control

No functions or short range.

-Insert new batteries.

-Aim the remote directly towards the remote sensor.

The sound is distorted

Check the volume setting on both the speaker and your device

and adjust the volume to a suitable level.

No sound can be heard

Check whether the volume is set in MUTE mode, and then

adjust the volume level in desired level.

12. Technical Information

AC power source

AC 230V~50Hz

Remote Control:

3V (Lithium CR2025 x 1pc.)

Unit Output Power:

Total 60 Watt (45Watt RMS 10%THD)

Speaker unit

2 x 3.5” speakers + 1 x 4” speaker

The Max. power consumption :

Max 60W

Operation temperature:

0°C to + 40°C

Aux:

3.5mm stereo jack

Power Management

15 minutes after no signal from unit

The Power Consumption in standby:

≤1W

Note:

As a result of continuous improvements, the design and specifications of the product within the

packaging might differ slightly from the unit illustrated on the packaging.

For more information, please contact the local authority or your retailer where you purchased the

product.

This product operates at 2400 - 2483.5 MHz and is designated only to be used inside a normal

household environment. This product is suited for this purpose within all EU counties.

12

13. Guarantee

Lenco offers service and warranty in accordance to European law, which means that in case of

repairs (both during and after the warranty period) you should contact your local dealer.

Important note: It is not possible to send products that need repairs to Lenco directly.

Important note: If this unit is opened or accessed by a non-official service center in any way, the

warranty expires.

This device is not suitable for professional use. In case of professional use, all warranty obligations of

the manufacturer will be voided.

14. Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the

instruction, specifications and pictures in this documentation may differ slightly from your particular

situation. All items described in this guide for illustration purposes only and may not apply to

particular situation. No legal right or entitlements may be obtained from the description made in

this manual.

15. Disposal of the Old Device

This symbol indicates that the relevant electrical product or battery should not be

disposed of as general household waste in Europe. To ensure the correct waste

treatment of the product and battery, please dispose them in accordance to any

applicable local laws of requirement for disposal of electrical equipment or

batteries. In so doing, you will help to conserve natural resources and improve

standards of environmental protection in treatment and disposal of electrical

waste (Waste Electrical and Electronic Equipment Directive).

16. CE Marking

Products with the CE marking comply with the EMC Directive (2014/30/EU) and

the Low Voltage Directive (2014/35/EU) issued by the Commission of the

European Community.

Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The

Netherlands, declares that this product is in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

The declaration of conformity may be consulted at [email protected]m

17. Service

For more information and helpdesk support, please visit www.lenco.com

Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, The Netherlands.

Page is loading ...

Lenco BTL-450 Owner's manual

Related papers

Other documents