Kobe CH0148SQB User manual

KOBE Brand Range Hood



Model No. / N

os

de modèles / Modelo No.

CH0130SQB

CH0136SQB

CH0142SQB

CH0148SQB

CH-101 SERIES – 18” HEIGHT

 



INSTALLATION INSTRUCTIONS

AND OPERATION MANUAL

MANUEL D'INSTALLATION

ET MODE D'EMPLOI

INSTRUCCIONES DE INSTALACIÓN

Y MANUAL DE OPERACIÓN

Page is loading ...

1











- READ AND SAVE THESE INSTRUCTIONS -

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .....................................................................................2

COMPONENTS OF PACKAGE...................................................................................................4

INSTALLATION ...........................................................................................................................5

OPERATION INSTRUCTIONS..................................................................................................12

MAINTENANCE ........................................................................................................................14

SPECIFICATIONS ....................................................................................................................16

MEASUREMENTS & DIAGRAMS .............................................................................................17

PARTS LIST ..............................................................................................................................19

CIRCUIT DIAGRAM ..................................................................................................................22

TROUBLE SHOOTING .............................................................................................................23

DISCLAIMER ............................................................................................................................24

WARRANTY .............................................................................................................................25

PRODUCT REGISTRATION .....................................................................................................27

- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -

ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN

ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES.

2

IMPORTANT SAFETY INSTRUCTIONS

- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -





: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, OBSERVE THE FOLLOWING:

1) Installation and electrical wiring must be done by qualified professionals and in accordance with all

applicable codes and standards, including fire-rated construction.

2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden

utilities.

3) Ducted fans must be vented to the outside.

a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE

PANEL.

b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air

properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl

spaces or garages.

NOTE - This warranty is invalid without an authorized agent’s receipt or if unit is

damaged due to misuse, poor installation, improper use, mistreatment,

negligence or any other circumstances beyond the control of KOBE

RANGE HOODS authorized agents. Any repair carried out without the

supervision of KOBE RANGE HOODS authorized agents will

automatically void the warranty.

- KOBE RANGE HOODS will not be held responsible for any damages to

personal property or real estate or any bodily injuries whether caused

directly or indirectly by the range hood.







: TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE

TOP GREASE FIRE:



1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease

should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.

2. Always turn hood ON when cooking.

3. Use high settings on cooking range ONLY when necessary.

4. Do not leave cooking range unattended when cooking.

5. Always use cookware and utensils appropriate for the type and amount of food prepared.

6. Use this unit only in the manner intended by the manufacturer.

7. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent

power from switching on accidentally.

8. Clean ventilating fan frequently.



3

What to Do In The Event Of a Range Top Grease Fire



• SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.

KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not

go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.

• NEVER PICK UP A BURNING PAN – You May Get Burned.

• DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.

• Use an extinguisher ONLY if:

a) You have a Class A, B, C extinguisher and know how to operate it.

b) The fire is small and contained in the area where it started.

c) The fire department has been called.

d) You can fight the fire with your back to an exit.



What to Do If You Smell Gas



-

Extinguish any open flame.

-

Do not try to turn on the lights or any type of appliance.

-

Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and

Fire Department right away.





1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and

vapors.

2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion

and exhausting of gases through the flue (chimney) to prevent back drafting.

3) Follow the heating equipment manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.

4) Activating any switch on may cause ignition or an explosion.

5) Due to the size and weight of this hood, two people installation is recommended.







ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.

Disconnect appliance from electric power before servicing. If equipped, the

fluorescent light bulb contains small amounts of mercury, which must be

recycled or disposed of according to Local, State, and Federal Codes.



4

COMPONENTS OF PACKAGE

(Must keep all material for returns or refunds)

RANGE HOOD BOX

c

KOBE Range Hood – 1

d

Warranty Registration Card –1

e

Instructions Manual – 1

f

Baffle Filter

- 2 (30”, 36”, 42”)

- 3 (48”)

g

Stainless Steel Spacer

- 1 (30”)

- 3 (36” & 42”)

- 2 (48”)

h

Oil Tunnel – 1

i

Ducting Transition – 1

j

Screw Package – 1

k

Hood-Mounting Bracket-2

l

Screw Package –1

c

d

e

f

g

h

i

j

k l

ORIGINAL KIT

(Sold Separately)

Option Of:

Model No. CH0030DC-12 for 30'' hood

KOBE Duct Cover – 1

Screw Package for Duct Cover - 1

Model No. CH0036DC-12 for 36'' hood

KOBE Duct Cover – 1

Screw Package for Duct Cover - 1

Model No. CH0042DC-12 for 42'' hood

KOBE Duct Cover – 1

Screw Package for Duct Cover - 1

Model No. CH0048DC-12 for 48'' hood

KOBE Duct Cover – 1

Screw Package for Duct Cover - 1

- FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR

CONTACT KOBE RANGE HOODS AT (626-775-8880).

5

INSTALLATION

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING

Calculation before Installation



Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.)

- FOR UNDER THE CABINET -

TABLE 1

A = Height of Floor to Ceiling

B = Height of Floor to Counter Top

(Standard: 36”)

C = Preferred Height of Counter Top to Hood

Bottom (Recommended 27” to 30”)

D = Height of Hood

E = Height of the Cabinet



- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) -

TABLE 2

A = Height of Floor to Ceiling

B = Height of Floor to Counter Top

(Standard: 36”)

C = Preferred Height of Counter Top to Hood

Bottom (Recommended 27” to 30”)

[(A – B] – (D + E)]

D = Height of Hood

E = Height of Duct Cover



6



 

HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS

NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.

NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD

MAY OCCUR.



Installation Contents

UNDER THE CABINET INSTALLATION ............................................................................................... 7

WALL MOUNT INSTALLATION ............................................................................................................. 9



7

UNDER THE CABINET INSTALLATION

Preparation before Installation

NOTE: TO AVOID DAMAGE TO YOUR HOOD,

PREVENT DEBRIS FROM ENTERING

THE VENT OPENING.



Decide the location of the venting pipe from the

hood to the outside. Refer to Figure 1.



A straight, short venting run will allow the hood

to perform more efficiently.



Try to avoid as many transitions, elbows, and

long run as possible. This may reduce the

performance of the hood.



Temporarily wire the hood to test for proper

operation before installing.



Important: Peel protective film off the hood

(if any).



For installing under the cabinet with recessed

bottom, attach 4-inch wide wood filler strips (not

included) on each side. Refer to Figure 2.



Measure and create access opening for

electrical wires under the cabinet.

Hood Installation

CAUTION: If required to move the cooking

range to install the hood, turn off the power on

an electric range at the main electrical box.

SHUT OFF THE GAS BEFORE MOVING A GAS

RANGE.

1. Puncture the knockout holes on the hood as

shown in Figure 3.

2. Attach ducting transition to hood exhaust with

six (3/16” x 1/2”) screws (included). Shown in

Figure 4.

3. Using references on Table 1 and

measurements on page 17-18 to center the

hood in place beneath the cabinet and flush

with the front of the cabinet.

4. Draw electrical wires through cabinet access

opening.

5. From the bottom of the hood, place screw (not

provided) into the exact center of each

knockout hole. Make sure all screws are in

place before tightening screws. CAUTION:

MAKE SURE THE HOOD IS SECURE

BEFORE RELEASING.

6. For safety purpose, pre-drilled mounting holes

are provided through the back of the hood. For

a more secure installation, use as many

mounting holes as needed to secure from the

inside of hood (screws not included).

Figure 1

Figure 2

Figure 3

Figure 4

8

Ductwork Installation

7. Use 8” round steel pipe (follow building codes

in your area) to connect the ducting transition

on the hood to the ductwork above. Use duct

tape to make all joints secure and air tight.

Refer to Figure 5.

Wiring to Power Supply

 

RISK OF ELECTRICAL SHOCK. THIS RANGE

HOOD MUST BE PROPERLY GROUNDED.

MAKE SURE THIS IS DONE BY SPECIALIZED

ELECTRICIAN IN ACCORDANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL

ELECTRICAL CODES. BEFORE CONNECTING

WIRES, SWITCH POWER OFF AT SERVICE

PANEL AND LOCK SERVICE PANEL TO

PREVENT POWER FROM BEING SWITCHED

ON ACCIDENTALLY.

8. Connect the electrical wires.

- Connect three wires (black, white and

green) to house wires and cap with wire

connectors. Connect according to color:

black to black, white to white, and green to

green as shown on Figure 6.

- If necessary to hide the electrical wire

connections, push wires back into the

wiring box. Access the wire connections

underneath the hood. Make sure wires do

not slip between motor or any moving parts

to prevent any damage.

Install Accessories

9. Attach Oil Tunnel. Refer to Figure 7.

10. Refer to Figure 8. c Slide the baffle filter into

the hood. d Push the baffle filter upward. e

Slide forward. f Pull downward. g Fit into

place.

11. Repeat for all baffle filters and spacers. Refer

to page 18.

12. Install heating lamps (not included), 120 Volts

175 Watts max. each.

Final Assembly

13. Turn power ON in control panel. Check all

lights and fan operation.

14. Make sure to leave this manual for the

homeowner.

Figure 5

Figure 6

Figure 7

Figure 8

9

WALL MOUNT INSTALLATION

***This installation only applied with the purchase

of an optional duct cover:

Preparation before Installation

NOTE: TO AVOID DAMAGE TO YOUR HOOD,

PREVENT DEBRIS FROM ENTERING

THE VENT OPENING.



Decide the location of the venting pipe from the

hood to the outside. Refer to Figure 9.



A straight, short venting run will allow the hood

to perform more efficiently.



Try to avoid as many transitions, elbows, and

long run as possible. This may reduce the

performance of the hood.



Use duct tape to seal the joints between pipe

sections.



If necessary, prepare back wall frame with

cross framing lumber for secure installation.



Using references on Table 2 and

measurements on page 17-18, decide the level

of the lumber. Refer to Figure 10.

Hood Preparation before Installation

x Temporarily wire the hood to test for proper

operation before installing.

x Important: Peel protective film off the hood

and the duct cover (if any).

x Attach ducting transition to hood exhaust with

six (3/16” x 1/2”) screws (included). Refer to

Figure 11.

x If necessary, attach two rubber stands

(included) with adhesive tape (included) to the

back corners of the hood.

x Use twelve (3/16” x 1/2”) screws (included) to

attach the two hood-mounting brackets

(included) to the back of the hood. Refer to

Figure 12.

Figure 9

Figure 10

Figure 11

Figure 12

10

Hood Installation

CAUTION: If required to move the cooking

range to install the hood, turn off the power on

an electric range at the main electrical box.

SHUT OFF THE GAS BEFORE MOVING A GAS

RANGE.

1. Using references in Table 2 on page 4 and

Measurements and Diagrams on pages 17-18,

mark the leveling point of the hood. Position

two mounting screws (not included) on the wall,

leaving 1/8” away from the wall. Refer to Figure

13.

2. Align hood-mounting bracket to the two screws

on the wall and hook hood into place. Tighten

screws to secure hood to the wall.

3. For safety purpose, pre-drilled mounting holes

are provided through the back of the hood. For

a more secure installation, use as many

mounting holes as needed to secure from the

inside of hood (screws not included).

CAUTION: MAKE SURE HOOD IS

SECURE BEFORE RELEASING.

Wiring to Power Supply

 

RISK OF ELECTRICAL SHOCK. THIS RANGE

HOOD MUST BE PROPERLY GROUNDED.

MAKE SURE THIS IS DONE BY SPECIALIZED

ELECTRICIAN IN ACCORDANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL

ELECTRICAL CODES. BEFORE CONNECTING

WIRES, SWITCH POWER OFF AT SERVICE

PANEL AND LOCK SERVICE PANEL TO

PREVENT POWER FROM BEING SWITCHED

ON ACCIDENTALLY.

4. Connect the electrical wires.

- Connect three wires (black, white and

green) to house wires and cap with wire

connectors. Connect according to color:

black to black, white to white, and green to

green as shown on Figure 14.

- If necessary to hide the electrical wire

connections, push wires back into the

wiring box. Access the wire connections

underneath the hood. Make sure wires do

not slip between motor or any moving parts

to prevent any damage.

Figure 13

WALL

Figure 14

11

Duct Cover Installation

5. Use 8” round steel pipe (follow building codes

in your area) to connect the ducting transition

on the hood to the ductwork above. Use duct

tape to make all joints secure and air tight.

Refer Figure 15. Slide the duct cover onto the

hood.

6. Use 3/16” x 1/2” screws (included) to attach

duct cover to hood.

Install Accessories



7. Attach oil tunnel. Refer to Figure 16.

8. Refer to Figure 17. c Slide the baffle filter into

the hood. d Push the baffle filter upward. e

Slide forward. f Pull downward. g Fit into

place.

9. For bottom casing, repeat above steps. Refer

to page 18.

10. Install heating lamps (not included), 120 Volts

175 Watts max. each.

Final Assembly

11. Turn power ON in control panel. Check all

lights and fan operation.

12. Make sure to leave this manual for the

homeowner.

Figure 15

Figure 16

Figure 17

12

OPERATION INSTRUCTIONS



Figure 18

LCD DISPLAY (OFF)



PRESS

TO TURN ON/OFF THE LCD SCREEN

(When power is turned on, LCD screen will light up & remain lit until turn off. When power is

turned off, LCD screen will remain lit for several seconds before turning off.)

Figure 19

LCD DISPLAY



13

GENERAL SETUP

(During menu option, if a function is not chosen within 10 seconds, the icon will stop flashing &

menu option will end.

z

Setting Time

1. Press

until time icon flashes.

2. Press

or to select current time by hh:mm.

ƽ

Temperature Scale Setting

1. Press

until icon flashes.

2. Press

or to select Celsius or Fahrenheit.

HOOD OPERATION

z

Turning Fan ON/OFF

1. Press

to turn fan ON.

(Each press of

will cycle the fan through QuietMode™, Low, Medium,

High, and off.)

2. Press

once will place fan on 3 minute delay shutoff.

OR

Press

twice will immediately turn fan OFF.

z

Turning ISC (Integrated Sensor Control) ON/OFF

1. Press

to turn ISC ON.

(

will indicate that the ISC system is ON. When gas or higher than

normal room temperature is detected, fan will automatically turn ON. Fan will

turn to its highest speed and decrease speed until all gas and smoke are

eliminated.)

2. Press

to turn ISC OFF.

z

Turning Lights ON

(Light control is separate from ON/OFF control. Turning power off will not turn lights

off.)

1. Press

to turn halogen lights ON.

(Each press of

will cycle the light intensity through low, high, and off.)

14

z

Setting Timer Mode

1. Press

until icon flashes.

2. Press

or to set the desire time in the timer mode by mm:ss.

3. Press

until none of the icons are flashing to begin timer.

(When countdown reaches 00:00, a warning sound will be emitted.)

MAINTENANCE

For the optimal level of operation, clean the range hood surface and baffles regularly.

To Clean Hood Surface

CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.

*** Regular care will help preserve its fine appearance.

1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.

2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the

surface of the hood. Avoid getting cleaning solution onto or into the control panel.

Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as

this may cause damage to hood finish. Use soft towel to wipe off the cleaning

solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood.

3. DO NOT allow deposits to accumulate or remain on the hood.

4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the

surface and cause rusting.

5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain

in contact with stainless steel for extended periods. Many of these compounds contain

chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a

clean lint free cloth.

To Clean Baffle Filters & Oil Tunnel

CAUTION: DRAIN BAFFLE FILTERS AND OIL TUNNEL BEFORE OIL WILL OVERFLOW.

1. Remove the baffle filters and oil tunnel.

2. Using a sponge, wash with warm soapy water. Dry completely before returning into

place.

(Note: Baffle Filters are top rack dishwasher safe.)

15

Replacing Light Bulb

CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL.

c

cc

c

d

dd

d

e

ee

e

f

ff

f

1. Make sure all controls are off, and range hood is unplugged.

2. Place the flat-headed screwdriver into the groove of the halogen light glass covering and

the housing.

c

cc

c

3. Pop out the halogen light glass covering. d

dd

d

4. Gently pull out the defective light bulb and discard. Light bulbs should be 12V 20W

maximum.

e

ee

e

5. Using a cloth, hold the new light bulb and push securely into light socket.

6. Return halogen light glass cover to the housing.

f

ff

f

7. Turn range hood ON to test for operation.

16

SPECIFICATIONS

MODEL / SIZE

CH0130SQB / 30”

CH0136SQB / 36"

CH0142SQB / 42”

CH0148SQB / 48”

COLO

R

Commercial Grade Stainless Steel

CONSUMPTION / AMPERE

CH0130SQB – 650W / 5.59A

CH0136SQB – 650W / 5.59A

CH0142SQB – 670W / 5.77A

CH0148SQB – 670W / 5.77A

VOLTAGE

120V 60Hz

NUMBER OF MOTORS

1

DESIGN

18-Gauge Seamless / Satin Finish

FAN TYPE: CENTRIFUGAL

Squirrel Cage

EXHAUST

Top Transition Rectangular to 8” Round

CONTROLS

Touch Screen Multi Function LCD

HALOGEN LIGHTS

12V 20W x 2 – 30”, 36”

12V 20W x 3 – 42”, 48”

HEATING LAMPS

120V 175W Max. x 2 (Bulbs Not included)

HOOD DIMENSION

(W x D x H)

(CH0130SQB) 29-3/4” x 24” x 18”

(CH0136SQB) 35-3/4” x 24” x 18”

(CH0142SQB) 41-3/4” x 24” x 18”

(CH0148SQB) 47-3/4” x 24” x 18”

OPTIONAL ACCESSORIES

(W x D x H)

1) Original Kit - Duct Cover:

Model No. CH0030DC-12 30” x 12” x 12”

Model No. CH0036DC-12 36” x 12” x 12”

Model No. CH0042DC-12 42” x 12” x 12”

Model No. CH0048DC-12 48” x 12” x 12”

2) Model No. SSP30

30” Stainless Steel Back Panel 30” x 1/10” x 32”

3) Model No. SSP36

36” Stainless Steel Back Panel 36” x 1/10” x 32”

HOOD WEIGHT (lbs)

Net

Gross

(CH0130SQB)

71 89

(CH0136SQB)

77 97

(CH0142SQB)

88 111

(CH0148SQB)

95 119

SPEED

QuietMode¥

¥¥

¥

Low Medium High

Air Capacity (cfm)*

400 600 800 1000

Sone

1.4* 3.5 7.0 8.0

*In House Test Static Pressure “0”. One sone is equivalent to the sound of a refrigerator at 40 decibels.

**Specifications subject to change without notice.

17

MEASUREMENTS & DIAGRAMS

 All measurements in ( ) are millimeters.

 All inch measurements are converted from millimeters. Inch measurements

are estimated.

- FOR UNDER THE CABINET -

- FOR WALL MOUNT -

MODEL NO.: CH0130SQB

CH0136SQB

CH0142SQB

CH0148SQB

MODEL NO.: CH0130SQB

CH0136SQB

CH0142SQB

CH0148SQB

18

- FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) -

***Rear Knock out Holes ***Hood-Mounting Bracket



19

PARTS LIST

MODEL NO.: CH0130SQB

CH0136SQB

CH0142SQB

CH0148SQB

(Optional Duct Cover)

NO. DESCRIPTION MODEL /SIZE PART NO.

1 Ducting Transition FA-12001-0506-01 (B001-2)

2 Hood Casing CH0130SQB 10-5530B-51

CH0136SQB 10-5536B-51

CH0142SQB 10-5542B-51

CH0148SQB 10-5548B-51

3 Halogen Light Unit (12V 20W Max.) C1-0403-0101

4 LCD Panel Box

LCD Panel

LCD001 FA-12001-0404-A

FA-12001-0404-B

5 Oil Tunnel CH0130SQB B101-2130-14

CH0136SQB B101-2136-14

CH0142SQB B101-2142-14

CH0148SQB B101-2148-14

6 Motor FA-12001-0302-01 (B001-4.5)

7 Lamp Socket Cover C1-0204-2130

8 Lamp Socket C1-0414-0120

9 Safety Screen FA-12001-0602-01 (B001-4.2)

10 Capacitor Panel CH0130SQB C1-0201-5530

CH0136SQB C1-0201-5536

CH0142SQB C1-0201-5542

CH0148SQB C1-0201-5548

11 Transformer (Light)

CH0130SQB C1-0402-0120-40B

CH0136SQB

CH0142SQB C1-0402-0120-60B

CH0148SQB

12 Capacitor FA-12001-0401-01

13 Processor Board Box C1-0501-0102

14 Processor Board LCD001 FA-12001-0404-C

15 Baffle Filter B101-2100-15

16

A

B

C

D

Bottom Casing

4” Wide CH0130SQB B101-2130-09

4” Wide

3” Wide

CH0136SQB

CH0136SQB B101-2136-09

5-1/4” Wide CH0142SQB B101-2142-09

4-1/2” Wide CH0148SQB B101-2148-09

17 Hood Mounting Bracket C1-0221-0330

18 Screw (3/16” x 1/2”) C1-0707-0001

19 ISC (Integrated Sensor Control) FA-12001-0402

BLOWER ASSEMBL

Y

NO. DESCRIPTION MODEL /SIZE PART NO.

6-1 Screws (3/16” x 1/2”) B001-4.1

6-2 Left Locknut B001-4.3

6-3 Left Squirrel Cage B001-4.4

6-4 Right Squirrel Cage B001-4.6

6-5 Right Locknut B001-4.7

6-6 Air Chamber B001-4.8

ORIGINAL KI

T

NO. DESCRIPTION MODEL /SIZE PART NO.

01 Duct Cover CH0030DC-12 B102-6012-030

CH0036DC-12 B102-6012-036

CH0042DC-12 B102-6012-042

CH0048DC-12 B102-6012-048

02 Screw (3/16” x 1/2”) C1-0707-0001

Page is loading ...

Kobe CH0148SQB User manual

This manual is also suitable for

Kobe CH0148SQB User manual

in other languages

Related papers

Other documents