Contents
TUMBLE DRYER
TCD 93B
First time you turn on your dryer
you must select your preferred
language see page 6
Instruction booklet
GB
English, 1
E
Español, 35
P
Português, 52
GR
EÏÏËÓÈο, 69
GB
1
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions
on how the appliance works.
This symbol reminds you to read this booklet.
F
Français, 18
Important information, 2-3
Installation, 4
Where to put your dryer
Ventilation
Water drain
Electrical connection
Before you start using your dryer
Dryer description, 5
The features
Control panel
The Display, 6-8
Start and programmes, 8-11
Choosing a programme
Special programmes
Programme option modifiers
Table of programmes
The controls
Laundry, 12-13
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 14
General safety
Saving energy and respecting the environment
Maintenance and Care, 15
Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Empty the water container after each cycle
Cleaning the condenser unit
Cleaning the dryer
Troubleshooting, 16
Service, 17
Disposal
Important Information
2
GB
! You MUST clean the fluff filter after EVERY drying
cycle.
Fluff Filter...
! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.
- It will take longer to dry and as a result will use more electricity during drying.
! You MUST empty the water container after EVERY
drying cycle.
Water Container...
Priming the Water Collection System
When your dryer is new, the water container will not collect water until the system is primed... this will take 1 or 2 drying
cycles. Once primed it will collect water during every drying cycle.
STEP 1.
Open the door of your
dryer.
STEP 2.
Remove the filter.
STEP 3.
Open the filter and clean
any fluff deposits from
the filter mesh.
STEP 4.
Refit the filter - NEVER
run the dryer without the
filter in position.
For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:
STEP 1.
Pull the water container
towards you and remove
it fully from the dryer.
STEP 2.
Remove either the small or
large cap and empty the
water from the container.
! Failure to empty the water container will result in:
- The machine will stop heating (so the load may still be wet at the end of the drying cycle).
- The ‘Empty Water’ message will tell you that the water container is full.
STEP 3.
Refit the water container,
ensuring that it is pushed
fully back into position.
! The ‘Empty Water’
message reminds you to
empty the water container
at the end of each
programme.
GB
3
Important Information
Condenser Unit...
! You MUST clean the fluff from the condenser EVERY
month.
! Failure to clean the condenser could cause premature
failure of your dryer.
●
Check that:
- The positioning arrows are pointing upwards.
- The 3 clips are re-secured back into their ‘lock’ position.
STEP 3.
Flush the condenser, from
the rear with water, to
remove any fluff deposits.
STEP 4.
Refit the condenser unit
- ensure that the unit is
pushed in fully, all 3 clips
are re-secured and the
positiong arrows on the
front of the condenser are
pointing upwards.
Rotate 3 clips
STEP 1.
Open the condenser cover
- hold the handle and
pull towards you.
STEP 2.
Remove the condenser by
rotating the 3 clips then
pulling the condenser
towards you.
(There may be some water
in the tubes, this is normal).
4
GB
Installation
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
Where to put your dryer
●
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
●
If you are going to install the
appliance under a work
counter, be sure to leave a
10mm space between the
top and any other objects
on or above the machine and
a 15mm space between the
sides and lateral furnishings
or walls.
This is to ensure proper air circulation.
Ventilation
When the dryer is in use, there has to be adequate
ventilation. Make sure you put your dryer in an
environment that is not damp and has proper air
circulation throughout. Airflow around the dryer is
essential to condense the water produced during the
washing, the dryer will not operate efficiently in an
enclosed space or cupboard.
! If using the dryer in a small or cold room some
condensation could be experienced.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3' (1m)
from the bottom of the dryer.
Remove hose from position shown
(see diagram).
Fit a suitable length of hose to the
new location shown (see diagram).
! Make sure that the hose is not squashed or kinked when
the dryer is in its final location.
Electrical connections
Make sure of the following before you insert the plug
into the the electrical socket:
●
The socket must be grounded.
●
The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).
●
Power voltage must be within the values indicated
on the rating label (see Dryer Description).
●
The socket must be compatible with the dryers plug.
Should this not be the case, replace the plug or the
socket.
! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this dryer
and fitted only by authorised technicians (see Service).
New or longer power cords are supplied at an extra
charge by authorised dealers.
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a
qualified electrician.
Minimum gap 10mm
Minimum gaps
15mm
Remove hose from
here...
...fit new hose here.
GB
5
Dryer Description
Control panel
PROGRAMME
Selection Buttons
Display Unit
START/PAUSE
Button & Light
CHILD LOCK
Button
ON/OFF
Button
OPTION
Buttons & Lights
The features
Water container
Filter
Condenser cover
The ON/OFF button : If the dryer is running and
this button is pressed, the dryer is turned off.
Press again, the dryer reactivates.
The PROGRAMME selection buttons set the programme:
press the button corresponding to the programme you
want to select (see Start and Programmes).
The OPTION buttons/indicators: these buttons select
available options for your selected programme (see
The Controls). The indicators on the display unit next
to the bottom buttons light to show that the option has
been selected.
The START/PAUSE button/light starts a selected
programme. When you press this button there will be
one beep and the display will show PAUSED . When
a programme is running, holding this button in pauses
the programme and stops the dryer.
The light is green when the programme is running,
flashing amber if the programme has been paused or
flashing green if on standby waiting to start a programme
(see Start and Programmes).
Note: This light also flashes amber during the Heat &
Enjoy programme and during the Post Care phase of
a programme.
The Display Unit gives warnings and information
about the programme selected and its progress (see
next page).
The CHILD LOCK button/icon : Press and hold this
button after selecting your programme and any options,
this prevents the programme settings from being
changed, the display will briefly show LOCKED .
When the icon is lit, the other buttons are disabled.
Hold the button to cancel and the icon will go out, the
display will briefly show UNLOCKED .
Note: This tumble dryer, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly
and wait for the dryer to reactivate.
Rating plate
Model & Serial numbers
Condenser cover handle
(Pull to open)
Air intake grille
6
GB
The Display
Selecting your language
Understanding the display
Programme selection and display
The selected programme is shown on the first line of the display when you select the corresponding button, this
message is shown while the programme is running.
My Cycle When you select the My Cycle button the Display will show your selected programme with ‘M’ before its
name. ie. M COTTONS (see Start and Programmes).
Dryness levels
During programme selection for an automatic programme that has different dryness levels available (see
Programmes Table).
The second line of the display shows the dryness level you require, for each press of the Dryness Level button the next
option from the list below is selected and displayed.
COTTONS
ANTI ALLERGY
SYNTHETICS
WOOL
BABY DELICATE
CUDDLY TOYS
EASY IRON
REFRESH
The first time you turn on your dryer you should select your preferred language from the available list.
To change: the language current selection must flash, on
the first line of the display.
- Press and hold all 3 buttons: Child Lock, Timed Dry
and Dryness Level for 5 seconds.
- Press the Child Lock or the Timed Dry button to
scroll up or down through the list.
- When your required language is flashing on the top line
of the display, pressing the Dryness Level button will
select your choice.
IRON DRY
CUPBOARD DRY
EXTRA DRY
Iron Dry: Dries your clothes ready for ironing.
Cupboard Dry: Dries your clothes ready for putting away.
Extra Dry: Dries your clothes ready for wearing.
The display also shows: one, two or three blocks, depending on your selection.
These are displayed during the programmes progress.
GB
7
The Display
Programme progress
Timed drying
After selecting a programme that has a Timed Dry option, press the Timed button and the display will increment
the selected time, each time you press and release the button (see Start and Programmes).
Delay and Time to End
Some programmes can have a delated start (see Start and Programmes). Press the Delay button and the icon flashes.
The second line of the display shows the status of the programme as it progresses:
(long messages scroll across the line)
PRE CARE
DRY
COOL TUMBLE
END OF CYCLE, POST CARE PHASE
END OF CYCLE, EMPTY THE WATER BOTTLE
Each press advances:
then , and then repeats.
Delicates have a maximum time of:
The bars to the right of the time, light to give an indication of
the time duration selected:
The selected time remains displayed after the programme
starts.
2:00
0:20 0:30 1:00 1:30 2:00 2:40 3:00
OFF
0:20 0:30 1:00 1:30 2:00 2:40 3:00
Each press of the Delay button advances the delay setting
in 1 hour increments, from: to , then and
then after a couple of seconds cancels the delay.
The delay time is shown on the display next to the Delay button.
The display counts down the minutes of the delay period after
the Start/Pause button is pressed.
The second line of the display shows STARTED
1h 24h
After the delay period finishes (or for all of the programme if delay not selected): The estimated Time to End of the
programme for automatic programmes or the actual time remaining during the Timed programme is shown in this part of
the display.
(if option Crease Care
available and selected).
(if option Crease Care
available and selected).
8
GB
The Display
Start and Programmes
Warnings
The second line of the display also gives warnings and reminders:
(reminders occur at the end of the programme)
END OF CYCLE, EMPTY THE WATER BOTTLE
●
Reminder that the water container should be
emptied every time you use the dryer (see
Maintenance).
EMPTY WATER BOTTLE
●
Indicates that the water container is full. The
message will take a few seconds to go out after
replacing the empty water container; the dryer
must be running for this to happen (see The
Controls).
Note: If the water container fills and this message
is displayed, the heat is turned off and your
clothes will not dry.
CLEAN CONDENSER
●
This message indicates that you must clean the
Condenser unit (see Maintenance) and will occur
at intervals depending how much you have used
the dryer. When you finish the next programme the
message is cancelled.
CLEAN FILTER
●
Reminds you to clean the Filter every time you use
the dryer (see Maintenance).
Choosing a programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place and the water container is empty and
in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the Display is not lit: Press the ON/OFF button
6. Press the Programmes Selection button that
corresponds with the type of fabric being dried by
checking the Programmes Table (see Programmes)
as well as the indications for each type of fabric (see
Laundry).
- If the button is selected; steps 7, 8 and 9 are not
required (see below).
7. Choose Timed Drying or Dryness Levels option:
- If Timed Drying press and release the
Timed button until the required time is
displayed.
or - To change from default dryness setting, press
and release the Dryness Levels button
until required level is indicated.
! See Programmes Table, for more details.
8. Set a delay time and other options if necessary
(see The Display).
9. If you wish the buzzer to sound at the end of the
programme, press the SOUND button.
10. Press the Start/Pause button to begin.
The display will show the estimated time to end.
During the drying programme, you can check on
your laundry and take out items that are dry while
others continue drying. When you close the door
again, press the Start/Pause button in order to
resume drying.
11. During the last few minutes of Drying Programmes,
before the programme is completed, the final COOL
TUMBLE phase is entered (fabrics are cooled),
this phase should always be allowed to complete.
12. The SOUND (if option selected) will warn you
when the programme is complete and the Display
shows END OF CYCLE, POST CARE PHASE .
Open the door, take the laundry out, clean the filter
and replace it. Empty the Water Container and
replace it (see Maintenance).
If the Crease Care option has been selected and
you do not remove the laundry immediately, the
dryer will tumble occasionally for 10 hours or until
you open the door.
13. Unplug the dryer.
My Cycle button:
First time you press this button the second line of the display will show PRESS AND HOLD TO STORE
After selecting your favorite programme and options you can save these settings by pressing and holding in the
My Cycle button for at least 5 seconds, the buzzer will then beep and the second line of the display shows MY CYCLE
The next time you need this programme press the button, then the Start/Pause button and this programme will run.
If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold in
the button (as above).
GB
9
Start and Programmes
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle
relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:
Fabric Maximum load
Cotton and Cotton mixtures 2.5kg
Synthetics 2kg
Denim 2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles
and put them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
Wool Programme
●
This is a programme for tumble dryer safe garments marked with the symbol .
●
It can be used for load sizes up to 1kg (approximately 3 sweaters).
●
We recommend that garments are turned inside out before drying.
●
This programme will take about 60 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
●
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.
! This programme is not suitable for Acrylic garments.
Programme option modifiers
Special Programmes
Baby Delicate Programme
●
This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille)
and for drying your delicate clothes.
●
DO NOT dry items such as bibs and nappy pants with plastic coverings.
●
It can be used for load sizes up to 2kg.
●
This programme will take about 60 minutes, but may take longer depending on the size and density of the load
and the spin speed used in your washer.
●
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be
slightly damp. If this is the case, try turning items inside out and running the programme again for a short period.
Heat & Enjoy
This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for
warming clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature) and runs at this
temperature for a maximum of 4 hours or until you stop the cycle by opening the door. Maximum load 3kg.
To select this programme press the Refresh programme button and then select the High Heat option.
Note: During this programme the Start/Pause light flashes Amber and the display shows END OF CYCLE, POST CARE PHASE.
Anti Allergy Programme
This programme has the ‘Seal of Approval’ endorsement from Allergy UK, which reflects the effective reduction and
elimination of allergens from the clothes with the special Anti Allergy cycle. With this programme, thanks to the
achievement of constant temperature for an extended period of time, the effects of the most common allergens
(including House Mites and Pollen) are neutralised.
Can be used on a wet load to dry and treat, or on a dry load just to treat your laundry.
Maximum load is 9kg for a wet load and 4kg for a dry load.
Quick Dry
This programme is for small loads up to 1kg Note: can only be used with the ‘Cupboard Dry’ setting.
Your drying time is very much reduced with a huge time saving up to 53% on cottons (with high heat option) and
50% on synthetics (with low heat option).
Cuddly Toy Programme
With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is
very much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature
and with soft mechanical action to maintain at best the original look and shine of the fur.
Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.
Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking
tape after drying them with a cloth.
The programme time will vary dependant on the exact make up of the load.
The maximum load should not exceed 2.5kg and no individual item should be greater than 600g.
Extra Care
This anti-ageing function for Cottons and Synthetics helps to maintain the brightness of your laundry for a long time
thanks to the use of the right drum rotation (reduced in the last part of the cycle) and the correct drying temperature
Note: It cannot be used with the ‘Extra Dry’ and ‘Cupboard Dry’ dryness levels.
10
GB
Start and Programmes
Programmes Table
Programme
What it does... How to set it... Notes/Options available:
Programme
What it does... How to set it...
Notes/Options available:
Cottons
Dries your Cotton
clothes.
Sound, Delay Timer,
Crease Care, High Heat
Extra Care, Quick Dry
1. Press the button.
2. Choose Timed Dry or Automatic Dryness
Level option.
- If Timed Dry , see next page, or...
- To change from default dryness setting
press and release Dryness Levels button
until the required level is displayed.
3. Select any Options if required.
4. Press the Start/Pause button .
Anti Allergy
Anti Allergy treatment
for your clothes.
Sound, Delay Timer,
Crease Care
●
An Automatic programme
Brief programme
(approximately 10
minutes) that softens
fibres of clothing that is
ready for ironing.
Sound
! This is not a drying
programme (see previous
page).
1. Press the button.
2. Select Sound option if required.
3. Press the Start/Pause button .
Synthetics
Dries your Synthetic
clothes on High Heat.
1. Press the button.
2. Choose Timed Dry or Automatic Dryness
Level option.
- If Timed Dry , see next page, or...
- To change from default dryness setting
press and release Dryness Levels button
until the required level is displayed.
3. Select any Options if required.
4. Press the Start/Pause button .
Baby
Delicates
Dries your clothes on
Low heat setting, ready
to be worn.
1. Press the button.
2. If Timed Dry programme required
(see Timed, next page).
Otherwise default is Automatic.
3. Select any Options, if required.
4. Press the Start/Pause button .
Wool
Dries your Woollen
clothes, (see previous
page).
Sound
Timed or
●
The default is Automatic.
1. Press the button.
2. Choose Timed Dry if required.
Otherwise default is Automatic.
3. Select Sound option if required.
4. Press the Start/Pause button .
Refresh
Easy Iron
20-minute programme
that airs your clothes
with cool air. Use also to
cool warm clothes.
1. Press the button.
2. Select Sound option if required.
3. Press the Start/Pause button .
! If the Display is not lit; Press the ON/OFF button and then select programme.
: default
Sound
●
Heat & Enjoy: Select High
Heat for this cycle (see
Programme option modifiers).
My Cycle
See previous details.
●
Depends on your chosen
programme
1. Press the M button.
2. Press the Start/Pause button .
1. Press the button.
2. Select any Options if required.
3. Press the Start/Pause button .
Cuddly Toys
Dries your cuddly toys.
1. Press the button.
2. Select any Options, if required.
3. Press the Start/Pause button .
Dryness options:
Automatic Dryness Levels
IRON DRY
CUPBOARD DRY
EXTRA DRY
*Where appropriate: Quick Dry is only available with the Cupboard Dry Dryness Level and Extra Care is only
available with the Iron Dry Dryness Level (see Programme option modifiers).
Sound, Delay Timer,
Crease Care, Extra Care,
Quick Dry
EXCLUSIVES
EXTRA
Programme
What it does... How to set it... Notes/Options available:
0:20 0:30
Sound, Delay Timer,
Crease Care
●
The default is Automatic.
Sound, Delay Timer
ESSENTIALS
: default
Dryness options:
Automatic Dryness Levels
IRON DRY
CUPBOARD DRY
EXTRA DRY
GB
11
Start and Programmes
Timed Drying
Timed Dry programmes table: First select a programme (see Programmes Table).
(0:20, 0:30,
1:00, 1:30, 2:00,
2:40 or 3:00
Hours:Minutes)
Always use Timed Drying
for loads less than 1kg, or
if you prefer a different
dryness result.
The heat settings available
depend on the programme
selected.
Use on low heat setting for
Acrylics and delicate materials
(see Laundry).
Consult suggested drying
times (see Laundry).
The last 10 minutes of these
programmes is the Cool
Tumble phase.
1. Press and release the button until the
display shows the required selection. Each
press advances , , , , ,
, then and then repeats.
●
Delicates have maximum time of
●
When is displayed, Automatic
Dryness Level option is available if you
change your mind.
2. Select any Options if required.
3. Press the Start button .
Options available:
! Warning, after pressing the Start/Pause button , the
programme cannot be changed.
To change a selected programme, press the Start/Pause
button , the light flashes Amber to indicate the
programme is paused. Select the new programme and
any options required, the light will then flash green.
Press the Start/Pause button again and the new
programme will start.
●
Option buttons
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected, by pressing a programme selection
button, before an option can be selected. Not all options
are available for all programmes (see Programmes Table).
If an option is not available and you press the button, the
buzzer will beep 3 times. If the option is available the
indicator, on the display unit above the bottom buttons,
lights to show that the option has been selected.
Time Delay (Delay Timer)
The start of some programmes (see The Display and
Programmes tables) can be delayed for up to 24 hours.
Ensure the water container is emptied before setting a
delayed start.
Crease Care
The pre-care option is only available if a delayed start has
been selected. It tumbles the clothes occasionally during the
delayed period to help prevent creases developing.
The post-care option occasionally tumbles the clothes after
end of the drying and cool tumble cycles to prevent creases
developing, should you not be available to remove the load
immediately the programme is complete. Note: The
Start/Pause light flashes Amber during this phase.
Selecting this option enables both the pre and post care
functions if appropriate.
High Heat
Allows Low Heat to be selected on some programmes.
When the light above this button is on High Heat is
selected. Not all programmes allow you to change this
setting. When High Heat is selected with the Refresh
programme this selects the Heat & Enjoy cycle.
Sound
Available on all programmes and allows the buzzer to
give a signal at the end of the drying cycle, to remind
you that the clothes are ready to be removed.
●
TIME DISPLAY
The display shows either the amount of time delay
remaining or an indication of the amount of time left for a
drying programme (see The Display).
The delay or time to end is displayed in hours and
minutes and counts down each minute.
The Controls
88:88
When timed programmes are selected the time displayed
throughout the cycle is the actual time remaining.
When an Automatic programme is selected, the time
displayed is an estimate of the time remaining. When the
programme is selected the display shows the time
required to dry a full load, after around 10 minutes the
controller calculates a better estimate of the cycle time.
The colons between the hours and minutes in the display
flash to show that the time is counting down.
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by a
fault code number (see Troubleshooting).
●
Empty Water Container
(If you have plumbed your dryer to a drain this icon can be
ignored, as there is no need to empty the water container).
Messages are displayed to reminds you to empty the
water container (see The Display).
If the water container fills during a programme, the heater
turns off and the dryer does a period of Cool Tumble.
After this it stops and a message tells you to
EMPTY THE WATER CONTAINER .
You must empty the water container and restart the dryer
or the clothes will not dry. After re-starting the dryer the
message will take a few seconds to go out.
To avoid this always empty the water container each time
you use the dryer (see Maintenance).
●
Door Opening
Opening the door during a programme will stop the dryer
and have the following effects:
Note: The Start/Pause light flashes Amber during the
Heat & Enjoy programme and during the Post Care phase
of a programme.
●
The display shows PAUSED .
●
During a delay phase the delay will continue to count
down. The Start/Pause button must be pressed to
resume the delay programme.
The display will change to show current status.
●
During the drying part of the programme, the colons
on the display stop flashing to show that the time has
stopped counting down.
The Start/Pause button must be pressed to resume
the programme. The display will change to show the
current status, the colons flash and count down
continues.
●
During the Post Care phase, the programme ends.
Pressing the Start/Pause button will restart a new
programme from the beginning.
●
Note
If you have a power cut, switch off the power or remove
the plug. When power is restored, press the Start/Pause
button and the programme will resume.
0:20
0:30
1:00
1:30 2:00
2:00
2:40 3:00
Sound, Delay Timer,
Crease Care, High Heat
12
GB
Laundry
Sorting your laundry
●
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
●
Sort laundry by fabric type.
●
Empty pockets and check buttons.
●
Close zippers and hooks and tie loose belts and
strings.
●
Wring out each item in order to eliminate as much
excess water as possible.
! Do not load dripping wet clothes into the dryer.
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 9kg max (20lb)
Synthetic fibres: 3kg max (6.6lb)
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical weights
Note: 1kg = 1000g (1lb = 16oz)
Clothes
Blouse Cotton 150g (5oz)
Other 100g (3oz)
Dress Cotton 500g (1lb 2oz)
Other 350g (12oz)
Jeans 700g (1lb 6oz)
10 nappies 1000g (2lb 3oz)
Shirt Cotton 300g (10oz)
Other 200g (7oz)
T-Shirt 125g (4oz)
Household Items
Duvet cover Cotton 1500g (3lb 5oz)
(Double) Other 1000g (2lb 3oz)
Large Tablecloth 700g (1lb 6oz)
Small Tablecloth 250g (9oz)
Tea Towel 100g (3oz)
Bath Towel 700g (1lb 6oz)
Hand Towel 350g (12oz)
Double Sheet 500g (1lb 2oz)
Single Sheet 350g (12oz)
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
●
Note: The last 10 minutes of any time set is the
Cool Tumble, so allow for this when setting the time,
as this period will not dry your laundry.
Wash Care Labels
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
May be tumble dried
Do not tumble dry
Tumble dry at high heat setting
Tumble dry at low heat setting
Items not suitable for tumble drying
●
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
●
Glass fibres (certain types of draperies)
●
Items which have been dry cleaned
●
Items with the ITCL Code (see Special
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
●
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
GB
13
Laundry
Special clothing items
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
Drying times
Times are approximate and can vary depending
upon:
●
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
●
Fabrics: items that are the same type of fabric but
different textures and thicknesses may not have
the same drying time.
●
Quantity of laundry: single items or small loads
may take longer to dry.
●
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
●
Heat setting.
●
Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to
dry your clothes.
●
Bulk: some bulky items can be tumble dried with
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
The table (see below) presents APPROXIMATE drying
times in Hours : Minutes, as you see them on the
display, the times are also shown in Minutes only for
reference.
The times given are for Cupboard Dry Automatic
programmes.
Timed Dry settings are also shown, to help you
choose a suitable time option.
Weights refer to dry garments.
Cottons
High Heat
Synthetics
High Heat
Delicates
(Acrylics)
Low Heat
Drying times 800-1000 rpm in washing machine.
Drying times on reduced spin in washing machine.
Drying times on reduced spin in washing machine.
Automatic duration
Timed Dry setting
Automatic duration
Automatic minutes
Timed Dry setting
Automatic duration
Automatic minutes
Timed Dry setting
1 kg
2 kg
4 kg
3 kg
1 kg
2 kg
1 kg
2 kg
3 kg
5 kg
6 kg
7 kg
0:30 - 0:40
0:40 - 0:55
1:10 - 1:20
0:55 - 1:10
1:20 - 1:30
1:35 - 2:00
2:00 - 2:20
30 - 40
40 - 55
70 - 80
55 - 70
80 - 90
95 - 120
120 - 140
0:30
0:40 - 0:50
40 - 50
1:00
Timed Dry only
Timed Dry only
0:30 1:00
0:50 - 1:10
50 - 70
1:00
1:10 - 1:30
70 - 90
1:00 or 1:30
1:00
1:30
1:00 or 1:30
1:30
1:30 or 2:00
2:00 or 2:40
8 kg
2:00 - 2:40
130 - 160
2:00 or 2:40
9 kg
2:30 - 2:50
140 - 170
2:40 or 3:00
14
GB
Warnings and Suggestions
! The appliance has been designed and built according
to international safety standards.
These warnings are given for safety reasons and must
be followed carefully.
General safety
●
This tumble dryer is not intended for use by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
●
This tumble dryer has been designed for home,
and not professional use.
●
Do not touch the appliance while barefoot or with
wet hands or feet.
●
Unplug the machine by pulling on the plug, not
the cord.
●
Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
●
Children should be supervised to ensure that they
do not play with the dryer.
●
The appliance must be installed correctly and
have proper ventilation. The air intake at the front
of the dryer should never be obstructed (see
Installation).
●
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
●
Check to see if the dryer is empty before loading it.
●
The back of the dryer could become very
hot. Never touch it while in use.
●
Do not use the dryer unless the filter, water
container and condenser are securely in place
(see Maintenance).
●
Do not overload the dryer (see Laundry for
maximum loads).
●
Do not load items that are dripping wet.
●
Carefully check all instructions on clothing labels
(see Laundry).
●
Do not tumble dry large, very bulky items.
●
Do not tumble dry acrylic fibres at high temperatures.
●
Complete each programme with its Cool Tumble Phase.
●
Do not turn off the dryer when there are still warm
items inside.
●
Clean the filter after each use (see Maintenance).
●
Empty the water container after each use (see
Maintenance).
●
Clean the condenser unit at regular intervals
(see Maintenance).
●
Do not allow lint to collect around the dryer.
●
Never climb on top of the dryer. It could result in damage.
●
Always follow electrical standards and requirements
(see Installation).
●
Always buy original spare parts and accessories
(see Service).
To minimise the risk of fire in your tumble dryer, the
following should be observed:
●
Tumble dry items only if they have been washed with
detergent and water, rinsed and been through the spin
cycle. It is a fire hazard to dry items that HAVE NOT
been washed with water.
●
Do not dry garments that have been treated with
chemical products.
●
Do not tumble dry items that have been spotted or
soaked with vegetable or cooking oils, this constitutes a
fire hazard. Oil-affected items can ignite spontaneously,
especially when exposed to heat sources such as a tumble
dryer. The items become warm, causing an oxidisation
reaction with the oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot enough to catch
fire. Piling, stacking or storing oil-effected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing vegetable or
cooking oil or those that have been contaminated with
hair care products be placed in a tumble dryer they should
first be washed with extra detergent - this will reduce, but
not eliminate the hazard. The cool tumble phase should
be used to reduce the temperature of the items. They
should not be removed from the dryer and piled or
stacked while hot.
●
Do not tumble dry items that have previously been
cleaned in or washed in, soaked in or soiled with
petrol/gasoline, dry cleaning solvents or other flammable
or explosive substances. Highly flammable substances
commonly used in domestic environments including
cooking oil, acetone, denatured alcohol, kerosene, spot
removers, turpentine, waxes and wax removers. Ensure
these items have been washed in hot water with an extra
amount of detergent before being dried in the tumble dryer.
●
Do not tumble dry items containing foam rubber (also
known as latex foam), or similarly textured rubber like
materials. Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
●
Fabric softener or similar products should not be used in
a tumble dryer to eliminate the effects of static electricity
unless the practice is specifically recommended by the
manufacturer of the fabric softener product.
●
Do not tumble dry undergarments that contain metal
reinforcements eg. bras with metal reinforcing wires.
Damage to the tumble dryer can result if the metal
reinforcements come loose during drying.
●
Do not tumble dry rubber, plastic articles such as shower
caps or babies waterproof covers, polythene or paper.
●
Do not tumble dry rubber backed articles, clothes fitted
with foam rubber pads, pillows, galoshes and rubber
coated tennis shoes.
●
Remove all objects from pockets, especially lighters
(risk of explosion).
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
Saving energy and respecting the environment
●
Wring out items to eliminate excess water before
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
●
Always dry full loads - you save energy: single
items or small loads take longer to dry.
●
Clean the filter after each use to contain energy
consumption costs (see Maintenance).
GB
15
Maintenance and Care
Cleaning the drum
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Cleaning the condenser unit
Periodically (every month) remove the condenser unit
and clean any build up of fluff from between the plates
by rinsing it under the tap with cold water.
This should be done with cold water from the rear of
the condenser.
Removing the condenser:
1. Unplug the dryer and open the door.
2. Pull open the condenser cover (see diagram).
Release the three catches by turning 90˚ counter-
clockwise then pull on the grip and remove from
the dryer.
3. Clean the surface of the seals and replace, making
sure that the catches have been secured.
Cleaning the dryer
●
External parts in metal or plastic and rubber parts
can be cleaned with a damp cloth.
●
Periodically (every 6 months) vacuum the front air
intake grille, to remove any build up of fluff, lint or
dust. Also to remove accumulation of fluff from the
front of the condenser and filter areas, clean
occasionally with a vacuum cleaner.
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
Switching off the electricity
! Unplug your dryer when not using it, when cleaning
it and during all maintenance operations.
Clean the filter after each cycle
The filter is an important part of your dryer:
it accumulates lint and fluff that is formed while drying.
When finished drying, clean the filter by rinsing it
under running water or with your vacuum cleaner.
Should the filter become clogged up, the airflow inside
the dryer will be seriously compromised: drying times
lengthen and you will consume more energy. It may
also damage your dryer.
The filter is found in front of the dryer trim (see diagram).
Removing the filter:
1. Pull the plastic grip of the filter upwards (see diagram).
2. Open the filter and clean the lint from
the inside.
3. Replace it correctly. Ensure the filter
is fully located flush into the tumble
dryer trim.
4. Remove any lint that has built up on the inside of the
door and around the door seal.
! Do not use the dryer without replacing the filter.
Check the drum after each cycle
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Empty the water container after each
cycle
Pull the container out of the dryer and remove either
the small or large cap and empty it into a sink or other
suitable drain. Refit the cap and replace the container
securely.
! Always check and empty the container before you
start a new drying programme.
Water container
Condenser cover
Catches
Air intake
Filter
Tap
Rear
Front
Condenser unit
Condenser unit
16
GB
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
Possible causes / Solution:
●
The plug is not plugged into the socket, or not making contact.
●
There has been a power failure.
●
The fuse has blown. Try to plug another appliance into the socket.
●
You are using an extension cord? Try to plug the dryer’s power cord
directly into the socket.
●
The door is not closed securely?
●
The programme has not been set properly (see Start and Programmes).
●
The Start/Pause button has not been pressed (see Start and Programmes).
●
You have set a delayed time (see Start and Programmes).
●
The filter has not been cleaned (see Maintenance).
●
The water container needs emptying? The empty water message is
displayed? (see Maintenance).
●
The condenser needs cleaning? (see Maintenance).
●
The temperature setting is not ideal for the type of fabric you are drying
(see Start and Programmes, and see Laundry).
●
The correct drying time has not been selected for the load (see Laundry).
●
The air intake grille is obstructed (see Installation, and see
Maintenance).
●
The items were too wet (see Laundry).
●
The dryer was overloaded (see Laundry).
●
The water container was probably not emptied at the start of the
programme. Do not wait for the empty water signal, always check and
empty the container before starting a new drying programme (see
Maintenance).
●
This is normal, the: END OF CYCLE, EMPTY THE WATER BOTTLE
message is shown as a reminder to empty the container (see The Display
and Start and Programmes).
! For safety the dryer has a maximum programme time of 4 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
●
If the display shows F10 or F15:
- Turn off and remove the plug. Clean the filter and the condenser
(see Maintenance). Then replace the plug, turn on and start another
programme. If F10 or F15 is still displayed contact the Service
Centre (see Service).
●
If any other number is shown: Note down the code and contact the
Service Centre (see Service).
●
The dryer is in ‘Demo’ mode. Press and hold both the On/Off and
Start/Pause buttons for 3 seconds. The display will show DEMO OFF for
3 seconds and then the dryer will resume normal operation.
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water message is
displayed but the dryer has
only been running for a short
period.
Empty water message is
displayed and the water
container is not full.
Programme finishes and
clothes are damper than
expected.
The display shows a fault
code F followed by one or two
numbers.
The display briefly shows
DEMO ON every 6 seconds.
Service
GB
17
Spare Parts
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
Call an authorised technician if you experience problems
while using the machine.
Before calling the Service Centre:
●
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
●
If not, turn off the dryer and call the Service Centre
closest to you.
What to tell the Service Centre:
●
name, address and post code.
●
telephone number.
●
the type of problem.
●
the date of purchase.
●
the appliance model (Mod.).
●
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
As part of our continued commitment to helping
the environment, we reserve the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
●
Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
●
To minimise risk of injury to children, remove the
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
Comparative Programmes
Recycling and Disposal Information
●
Programmes recommended for comparative test to EN61121
! Note: This is not a full list of programme options (see Start and Programmes).
This appliance conforms to the following EC Directives:
- 2006/95/EC (Low Voltage Equipment)
- 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)
Programme Programme to select Load size Heat Setting Dryness Option
(EN61121)
Dry Cotton COTTONS 9 kg High CUPBOARD DRY
Iron Dry Cotton COTTONS 9 kg High IRON DRY
Easy-care textile SYNTHETICS 3 kg Low CUPBOARD DRY
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/