Chauvet Professional Amhaze Studio Reference guide

Page is loading ...

Amhaze™ Studio QRG EN

2

About This

Guide

The Amhaze™ Studio Quick Reference Guide (QRG) has basic product

information such as connection, mounting, menu options, and DMX values.

Download the User Manual from www.chauvetprofessional.com for more details.

Disclaimer

The information and specifications contained in this QRG are subject to change

without notice.

Safety Notes

• Depending on the amount of haze generated, all haze machines may set off

smoke detectors.

• Drain the tank before transporting the product.

• This product is not intended for permanent installation.

• This product is for indoor use only! (IP20) To prevent risk of fire or shock, do

not expose this product to rain or moisture.

• Always disconnect from power before cleaning or replacing the fuse.

• Replace the fuse with the same type and rating.

• Do not operate this product if the housing, fluid tank, or cables appear

damaged.

• In the event of a serious operating problem, stop using immediately.

• DO NOT open this product. It contains no user-serviceable parts.

• Do not use for space heating purposes.

• Never disconnect this product from power by pulling on the cord.

• Mount this product in a location with adequate ventilation, at least

20 in (50 cm) from adjacent surfaces.

• USE a safety cable when mounting this product overhead.

• Do not touch the output nozzle on this product. It is very hot during operation

and it may remain hot for several hours after turning the product off.

• Do not leave any flammable material within 50 cm of this product while

operating or connected to power.

• Only use CHAUVET® (PHF or HFG) haze fluid.

• Do not add anything to the haze liquid.

• Do not drink the haze liquid.

• Do not allow the haze liquid to touch your skin or eyes.

• Do not connect this product to a dimmer or rheostat.

• Only connect this product to a grounded and protected circuit.

• Only use the handles to carry this product.

• The maximum ambient temperature is 113 °F (45 °C). Do not operate this

product at higher temperatures.

• To eliminate unnecessary wear and improve its lifespan, during periods of

non-use completely disconnect the product from power via breaker or by

unplugging it.

• CAUTION: When transferring product from extreme temperature

environments, (e.g. cold truck to warm humid ballroom) condensation may

form on the internal electronics of the product. To avoid causing a failure,

allow product to fully acclimate to the surrounding environment before

connecting it to power.

Amhaze™ Studio QRG EN

3

Contact

• From outside the U.S., UK, Ireland, or Mexico, contact the distributor of

record to request support or return a product.

• From inside the U.S., UK, Ireland, or Mexico, use the information in

Contact Us at the end of this QRG.

What Is

Included

• Amhaze™ Studio

• Neutrik® powerCON®

power cord

• Warranty Card

• Quick Reference Guide

AC Power

This product has a fixed voltage power supply and it can work with an input

voltage of either 120 VAC, 60 Hz or 230 VAC, 50 Hz, depending on the specific

model.

AC Plug

Connection

Wire (U.S.)

Wire (Europe)

Screw Color

AC Live

Black

Brown

Yellow/Brass

AC Neutral

White

Blue

Silver

AC Ground

Green/Yellow

Green

To eliminate unnecessary wear and improve its lifespan, during periods of

non-

use completely disconnect the product from power via breaker or by

unplugging it.

Replacing The Fuse

1. Disconnect this product from power.

2. Using a Phillips #2 head screwdriver, unscrew the fuse holder cap from the

housing.

3. Remove blown fuse and replace with a good fuse of the same type and rating.

4. Screw the fuse holder cap back in place and reconnect power.

DMX Linking

The Amhaze™ Studio will work with a DMX controller using a 3- or 5-pin DMX

serial connection. A DMX Primer is available from

www.chauvetprofessional.com.

DMX Connection

The Amhaze™ Studio uses a 3- or 5-pin DMX data connection for its 2-channel

DMX personality. See the User Manual for information about connecting

and

configuring the product for DMX operation.

Preparing for

Operation

To prepare the Amhaze™ Studio for operation:

1. Open the flight case.

2. Pull out the fluid tank and remove the cap.

3. Verify that the two plastic hoses attached to the cap are in place and in good

condition.

4. Pour CHAUVET® (PHF or HFG) haze fluid inside the tank, and re-cap.

5. Reinsert the tank.

6.

Make sure that the plastic hose that goes from the cap to the hazer is not bent.

7. Plug in power and wait approx. 2 min. for warm-up to complete.

Fluid Tank Indicator

Lights

Three internal indicator LEDs show the status of the fluid tank, as follows.

• Red - the fluid tank is currently heating up

• Blue - the fluid tank is ready

• Flashing Red/Blue - the fluid tank is actively re-heating while producing

output.

Only use CHAUVET® approved (PHF or HFG) haze fluid. Otherwise, you

might not have satisfactory results. In addition, unapproved fluid can damage

the Amhaze™ Studio or cause harm to humans or animals.

Amhaze™ Studio QRG EN

4

Mounting

Before mounting this product, read the Safety Notes. Use two mounting points per

product. Make sure the mounting clamps

are capable of supporting the weight of

the product. For our Chauvet line of mounting clamps, g

o to

www.trusst.com/productcategory/accessories-clamps/.

Product

Mounting

Diagram

Control Panel

Description

Button

Function

<MENU>

Exits from the current menu or function

<UP>

Navigates upwards through the menu list or increases the

numeric value when in a function

<DOWN>

Navigates downwards through the menu list or decreases

the numeric value when in a function

Overhead/Floor

Mounting

Mounting Clamp

Safety Cable

Rubber Feet (x4)

for floor mounting

Threaded

Mounting Hole

Size M13

Amhaze™ Studio QRG EN

5

Menu Map

Main Level

Programming Levels

Description

d

001–512

Selects the DMX starting address

F

000–005

Fan speed control

h

Haze volume control

DMX Values

2Ch

Channel

Function

Value

Percent/Setting

1 Fan Speed

000005

006255

No function

Fan speed (slow to fast)

2 Haze Volume

000005

006



255

No function

Haze volume 1-100%

Page is loading ...

Amhaze™ Studio QRG Multi-Language

Contact Us

WORLD HEADQUARTERS - Chauvet

General Information

Address:5200 NW 108th Avenue

Sunrise, FL 33351

Voice: (954) 577-4455

Fax: (954) 929-5560

Toll free:(800) 762-1084

Technical Support

Voice: (954) 577-4455 (Press 4)

Fax: (954) 756-8015

Email: tech@chauvetlighting.com

World Wide Web

www.chauvetlighting.com

UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.

General Information

Address:Unit 1C

Brookhill Road Industrial Estate

Pinxton, Nottingham, UK

NG16 6NT

Voice: +44 (0)1773 511115

Fax: +44 (0)1773 511110

Technical Support

Email: uktech@chauvetlighting.com

World Wide Web

www.chauvetlighting.co.uk

MEXICO - Chauvet Mexico

General Information

Address:Av. Santa Ana 30

Parque Industrial Lerma

Lerma, Mexico C.P. 52000

Voice: +52 (728) 285-5000

Technical Support

Email: servicio@chauvet.com.mx

World Wide Web www.chauvet.com.mx

Outside the U.S., United Kingdom, Ireland, or Mexico, contact the dealer of record.

Follow their instructions to request support or to return a product. Visit our website

for contact details.

Chauvet Professional Amhaze Studio Reference guide

This manual is also suitable for

Chauvet Professional Amhaze Studio Reference guide

in other languages

Related papers

Other documents