2. Home
  3. Do-It-Yourself tools
  4. Hand tools
  5. Measuring & layout tools
  6. Hamilton
  7. H100 CONDI

Hamilton H100 CONDI User manual

  • Hello! I am an AI chatbot trained to assist you with the Hamilton H100 CONDI User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
gelb: Pantone 124
blau: Pantone 541
Transmitter H100 CONDI
User Manual
www.hamiltoncompany.com
Latest Product Information:
092999
2
Warranty
Defects occurring within 3 years from delivery date shall be remedied free of charge at our
plant (carriage and insurance paid by sender).
Subject to change without notice.
Return of products under warranty
Please contact our Service Team before returning a defective device. Request a Return Goods
Authorization number (RGA). This number assures proper tracking of your device. Ship the
cleaned device to the address you have been given. If the device has been in contact with
process uids, it must be decontaminated/disinfected before shipment. In that case, please
attach a corresponding certicate, for the health and safety of our service personnel.
Disposal
Please observe the applicable local or national regulations concerning the disposal of “waste
electrical and electronic equipment”.
HAMILTON Bonaduz AG
Via Crusch 8
CH-7402 Bonaduz
Switzerland
Tel: +41 58 6101010
Fax: +41 58 6100010
Email: [email protected]
Web: www.hamiltoncompany.com
HAMILTON Company
4970 Energy Way
Reno, Nevada 89502 USA
Tel: +1 775 858 3000
Toll Free: 800 648 5950
Fax: +1 775 856 7259
Email: sensors@hamiltoncompany.com
Web: www.hamiltoncompany.com
Hamilton Bonaduz AG Shanghai Oce
Room 502, No.50 Boxia Road
Shanghai Pudong Software Park
201203 Shanghai
China
Phone: +86 21 61646567
Fax: +86 21 61063732
eMail: [email protected]
3
Table of Contents
Safety Information ................................................................. 5
Intended Use ....................................................................................................6
Registered Trademarks ................................................................................. 6
CD-ROM .............................................................................................................7
Safety Instructions .........................................................................................7
Quickstart Guides ........................................................................................... 7
Overview of Transmitter H100 CONDI .................................. 8
Assembly ................................................................................. 9
Package Contents ...........................................................................................9
Mounting Plan ...............................................................................................10
Pipe Mounting, Panel Mounting .............................................................11
Installation and Connection ................................................13
Installation Instructions .............................................................................13
Terminal Assignments ................................................................................13
Preparing the Shield Connection ...........................................................15
The Pre-Assembled Measuring Cable ...................................................15
Wiring Example.....................................................................17
Conducell I Sensor .......................................................................................17
Protective Wiring of Relay Outputs .......................................................18
User Interface and Display ..................................................20
Operation: Keypad ...............................................................22
Safety Functions ...................................................................23
Sensocheck, Sensoface Sensor Monitoring ........................................23
GainCheck Device Self-Test.......................................................................23
Automatic Device Self-Test .......................................................................23
Hold Mode ......................................................................................................24
Configuration ........................................................................26
Menu Structure of Configuration ...........................................................27
Overview of Configuration Steps ...........................................................28
Output 1 ..........................................................................................................30
Output 2 ..........................................................................................................44
Temperature Compensation ....................................................................50
4
Table of Contents
Alarm Settings ...............................................................................................52
Limit Function ................................................................................................54
Controlling a Rinsing Probe ......................................................................56
Connecting a Rinsing System ..................................................................57
Parameters ............................................................................58
Factory Settings of Parameters ...............................................................58
Parameters – Individual Settings ............................................................60
Calibration ............................................................................62
Calibration by Input of Cell Factor .........................................................64
Calibration with Calibration Solution ..................................................66
Product Calibration .....................................................................................68
Zero Calibration in Air ...............................................................................70
Zero Calibration with Calibration Solution ........................................72
Temp Probe Adjustment ............................................................................73
Measurement ........................................................................ 73
Diagnostics Functions .......................................................... 74
Error Messages (Error Codes) ..............................................76
Operating States ...................................................................78
Sensoface ..............................................................................79
Appendix ...............................................................................81
Product Line and Accessories ..................................................................81
Specifications .................................................................................................82
Calibration Solutions ...................................................................................88
Concentration Curves .................................................................................91
Index ...................................................................................... 96
Passcodes ............................................................................100
5
Safety Information
Be sure to read and observe the following instructions!
The device has been manufactured using state of the art technology
and it complies with applicable safety regulations.
When operating the device, certain conditions may nevertheless lead
to danger for the operator or damage to the device.
CAUTION!
Commissioning must be carried out by trained experts.
Whenever it is likely that protection has been impaired, the device
shall be made inoperative and secured against unintended operation.
The protection is likely to be impaired if, for example:
• the device shows visible damage
• the device fails to perform the intended function
• after prolonged storage at temperatures above 70 °C
• after severe transport stresses
Before recommissioning the device, a professional routine test in
accordance with EN 61010-1 must be performed. This test should be
carried out at the manufacturer's factory.
CAUTION!
Before commissioning you must prove that the device may be
connected with other equipment.
Safety Information
6
Intended Use
The Model H100 CONDI is used for measurement of electrical conduc-
tivity and temperature in liquids. Fields of application are: biotechnol-
ogy, chemical industry, environment, food processing, water/waste-
water treatment.
The sturdy molded enclosure can be xed into a control panel or
mounted on a wall or at a post.
The protective hood provides additional protection against direct
weather exposure and mechanical damage.
The device has been designed for application with inductive (toroidal)
sensors. It provides two current outputs (for transmission of measured
value and temperature, for example), two contacts, and a universal
power supply 24...230VAC/DC, AC: 45 ... 65 Hz.
Registered Trademarks
The following names are registered trademarks. For practical reasons
they are shown without trademark symbol in this manual.
Sensocheck®
Sensoface®
GainCheck®
7
Documents Supplied
Quickstart Guide .................................................... 3
Kurzübersicht ........................................................ 15
Guide de démarrage rapide ............................ 27
Inicio rápido ..........................................................39
Transmitter H100 CONDI
Quickstart
www.hamiltoncompany.com
Latest Product Information:
Transmitter H100 Series
Safety Instructions
www.hamiltoncompany.com
Latest Product Information:
HAMILTON Bonaduz AG | CH-7402 Bonaduz | Switzerland
[email protected] | www.hamiltoncompany.com
Documentation
7. 00
PH
25.0
0
C
CD-ROM
Complete documentation:
• User manuals
• Safety instructions
• Quickstart guides
Safety Instructions
In ocial EU languages and others.
Quickstart Guides
In German, English, French, Spanish.
• Start-up
• Operation
• Menu structure
• Calibration
• Error messages and recommended actions
Declaration of Conformity
8
Overview of Transmitter H100 CONDI
Overview
11
12
13
14
15
16
19
20
10
9
3
4
5
C
D
E
6
7
8
2
1
Output 1
Shield
Do not connect
terminal !
+ Output 1
– Output 1/2
+ Output 2
Relay
Relay
Alarm
Alarm
Power supply
Power supply
CONDI
input
Output 2
Not in use
Do not connect
terminal !
Do not connect
terminal !
17
18
Cleaning
Cleaning
9
Assembly
Package Contents
Check the shipment for transport damage and completeness.
The package should contain:
• Front unit
• Rear unit
• Bag containing small parts
• CD-ROM with documentation
• Specic test report
• Passcode sticker
1 Jumper (2 x)
2 Washer (1 x), for conduit mounting:
Place washer between enclosure and
nut
3 Cable tie (3 x)
4 Hinge pin (1 x), insertable from either
side
5 Enclosure screw (4 x)
6 Sealing insert (1 x)
7 Rubber reducer (1 x)
8 Cable gland (3 x)
9 Filler plug (3 x)
10 Hexagon nut (5 x)
11 Sealing plug (2 x), for sealing in case
of wall mounting
Fig.: Assembling the enclosure
10
Assembly
Mounting Plan
144
144
15
42
84
80
32
21
43
105
27
72
6,2
12
3
4
Fig.: Mounting plan
1 Cable gland (3 x)
2 Knockouts for cable gland or
1/2“ conduit, ø 21.5 mm
(2 x)
Conduit couplings not
included!
3 Knockout for pipe mounting
(4x)
4 Knockout for wall mounting
(2x)
11
Assembly
Pipe Mounting, Panel Mounting
40 60
132
1
2
3
4
5
1
132165
173
1
1 P/N 243084 protective hood (if required)
2 Hose clamp with worm gear drive to DIN 3017 (2 x)
3 Pipe-mount plate (1 x)
4 For vertical or horizontal posts or pipes
5 Self-tapping screw (4 x)
Fig.: P/N 243082 pipe-mount kit
Fig.: Protective hood for wall and pipe mounting, P/N 243084
12
Assembly
1
2
3
45
max. 25
78 27
1...22
1 Screw (4 x)
2 Gasket (1 x)
3 Control panel
4 Span piece (4 x)
5 Threaded sleeve (4 x)
Cutout
138 x 138 mm (DIN43700)
Fig.: Panel-mount kit, P/N 243083
13
Installation Instructions
CAUTION!
• Installation of the transmitter must be carried out by trained experts
in accordance with this user manual and as per applicable local and
national codes.
• Be sure to observe the technical specications and input ratings
during installation.
• Be sure not to notch the conductor when stripping the insulation.
• Before connecting the device to the power supply, make sure that
its voltage lies within the range 20.5 ... 253 V AC/DC.
• All parameters must be set by a system administrator prior to
commissioning.
The terminals are suitable for single wires and exible leads up to
2.5mm
2
(AWG 14).
Installation and Connection
Terminal Assignments
Fig.: Transmitter H100 CONDI terminal assignments
83426/0000000/jjww
Tamb - 20 to + 55 °C
meas el.
aux.
el.
do not
connect
ref el.
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APP ROVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
Tamb: -20 to +55 °C
H100 pH
243080-01 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 83426 / 0000000 / JJWW
APP ROVE D
FM
SG
83427/0000000/jjww
Tamb - 20 to + 55 °C
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APP ROVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
Tamb: -20 to +55 °C
H100 COND
243080-02 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 83427 / 0000000 / JJWW
APP ROVE D
FM
ref. el.
anode
guard
cathode
do not
connect
Tamb: -20 to +55 °C
H100 DO
243080-03 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 83428 / 0000000 / JJWW
APP ROVE D
FM
83428/0000000/jjww
Tamb -20 to +55 °C
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APP ROVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
receive
lo
send
hi
lo
drain
hi
91524/0000000/1638
Tamb -20 to +55 °C
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APP ROVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
Tamb: -20 to +55 °C
H100 CONDI
243080-04 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 91524 / 0000000 / JJWW
APP ROVE D
FM
14
Installation and Connection
1 Terminals for temperature probe and outer shield
2 Terminals for sensor
3 Terminals for power supply
Fig.: Information on installation, rear side of device
2
1
3
83426/0000000/jjww
Tamb - 20 to + 55 °C
meas el.
aux.
el.
do not
connect
ref el.
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APPR OVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
Tamb: -20 to +55 °C
H100 pH
243080-01 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 83426 / 0000000 / JJWW
APPR OVED
FM
SG
83427/0000000/jjww
Tamb - 20 to + 55 °C
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APPR OVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
Tamb: -20 to +55 °C
H100 COND
243080-02 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 83427 / 0000000 / JJWW
APPR OVED
FM
ref. el.
anode
guard
cathode
do not
connect
Tamb: -20 to +55 °C
H100 DO
243080-03 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 83428 / 0000000 / JJWW
APPR OVED
FM
83428/0000000/jjww
Tamb -20 to +55 °C
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APPR OVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
receive
lo
send
hi
lo
drain
hi
91524/0000000/1638
Tamb -20 to +55 °C
1
2
3
4
5
Hamilton Bonaduz AG
Via Crusch 8
7402 Bonaduz
Switzerland
RTD
RTD
C
D
E
shield
do not
connect
do not
connect
7813
12
6
11
10 9
14
151620 19
+
+
-
alarm
rel. 1
24 to
230 V
ac/dc
out 1
out 2
power
output
17
18
contacts
clean
MAX. RELAY CONTACT RATING: AC < 250 V / < 3 A / < 750 VA, DC < 30 V / < 3 A / < 90 W, RESISTIVE
NI, CLI, DIV2, GRP A, B, C, D, T4
NI, CLI, ZN2, GP IIC, T4
ENCLOSURE TYPE 2
APPR OVED
FM
WARNING -EXPLOSION HAZARD- DO NOT DISCONNECT EQUIPMENT UNLESS POWER
HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
WARNING -BONDING BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE
PROVIDED AS PART OF THE INSTALLATION. SEE INSTALLATION INSTRUCTIONS.
WARNING -SUBSTITUTION OF COMPONENTS MAY IMPAIR SAFETY.
WARNING -CLEAN ONLY WITH ANTISTATIC MOISTENED CLOTH.
CAUTION -USE SUPPLY WIRES SUITABLE FOR 30°C ABOVESURROUNDING AMBIENT
AND RATED AT LEAST 250 V. USE SIGNAL WIRES SUITABLE FOR AT LEAST 250 V.
Tamb: -20 to +55 °C
H100 CONDI
243080-04 / 0000000
Power: 24 to 230 V AC/DC, 45 to 65 Hz
6 VA, 2,5 W
No. 91524 / 0000000 / JJWW
APPR OVED
FM
Division 2 Wiring
The connections to the device must be installed
in accordance with the National Electric Code
(ANSINFPA70) Division 2 hazardous (classied) location
non-incendive wiring techniques.
15
Preparing the Shield Connection
Cable for connecting the Conducell I sensor
Installation and Connection
3
4
5
receive hi
receive lo
send lo (jumper to 3!)
send hi
RTD (temp)
RTD (temp)
sense (temp)
shield
Transp.
RD
WH
GN
WH
YE
Coax RD
Coax WH
• Insert the cable through the
cable entry into the terminal
compartment.
• Remove the already separated part
of the cable insulation (1).
• Turn the shielding mesh (2) over the
cable insulation (3).
• Then shift the crimp ring (4) over the
shielding mesh and tighten it using a
pince (5).
The Pre-Assembled Measuring Cable
Transp.
16
17
Wiring Example
Conducell I Sensor
Connecting the pre-assembled cable
* The shield must be connected to the shielding mesh of
the cable using a crimp ring (see ”Preparing the Shield
Connection”).
receive hi
receive lo
drain
shield
RTD
Shield *
Coax RD
Coax WH
send lo
send hi
Transp.
RD
WH
Transp.
YE
GN
WH
RTD
Transmitter H100 CONDI
18
Protective Wiring of Relay Outputs
Protective Wiring of Relay Contacts
Relay contacts are subject to electrical erosion. Especially with induc-
tive and capacitive loads, the service life of the contacts will be
reduced. For suppression of sparks and arcing, components such as RC
combinations, nonlinear resistors, series resistors, and diodes should
be used.
1
2
3
1
2
3
AC applications with inductive load
1 Load
2 RC combination, e.g. RIFA PMR 209
Typical RC combinations for 230 V AC:
Capacitor 0.1 µF / 630 V, Resistor 100 ohms / 1 W
3 Contact
19
Protective Wiring of Relay Outputs
Typical Protective Wiring Measures
A: DC application with inductive load
B: AC/DC applications with capacitive load
C: Connection of incandescent lamps
A1 Inductive load
A2 Free-wheeling diode, e.g.,1N4007 (Observe polarity)
A3 Contact
B1 Capacitive load
B1 Resistor, e.g., 8 Ω / 1 W at 24 V / 0.3 A
B3 Contact
C1 Incandescent lamp, max 60 W / 230 V, 30 W / 115 V
C3 Contact
WARNING!
Make sure that the maximum ratings of the relay contacts are not
exceeded even during switching!
20
User Interface and Display
User Interface
gelb: Pantone 124
blau: Pantone 541
1 Display
2 Mode indicators (no keys),
from left to right:
- Measuring mode
- Calibration mode
- Alarm
- Cleaning contact
- Configuration mode
3 Alarm LED
4 Keypad
1
2
3
4
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/