Sole E55 Assembly Instructions Manual

Brand: Sole

Model: E55

Type: Assembly Instructions Manual

This manual is also suitable for

Sole Fitness E95 Ellipcal Trainer

TurnKey® Delivery and Setup Training

Delivery Requirements

• Ground delivery

• Inside delivery to customer-speciﬁed locaon

• Unpack and assemble machine, and remove packing materials

Tools Required

• Ligate

• Two-wheel dolly

• Cuers to cut plasc banding

1. Unload the carton from the trailer and take it to the

customer-speciﬁed locaon using a two-wheeled dolly.

When moving the carton, be sure to use safe liing

procedures. Be sure to bend at the knees and keep your

back straight.

2. Unpack the contents of the cartons and remove

all

packing

materials.

Cut along the

boom edge

of the carton.

Remove all

packing material.

Locate the

hardware

packet.

3. Review the assembly instrucons.

Inside the carton, you will ﬁnd the Owner’s Manual. It will be necessary for you to follow the manufacturer’s assembly instrucons to

be able to complete the assembly of the Sole Fitness E95 Ellipcal Trainer.

Do not aempt to assemble this machine without the Owner’s Manual.

4. Install the incline rail assembly into the U-channel bracket of the main frame.

Place the incline rail

assembly into the U-channel

on the main frame.

Install four bolts, split

washers, and star

washers into the top of

rail assembly.

Install two bolts

and two nylon nuts

into the sides of

the U-channel.

Connect the three incline motor power lines and

the 3-pin posion sensor connector on the main

frame to the corresponding ones on the incline

rail assembly.

(This is shown in Step 1.1 and 1.2 on page 8 of the Owners Manual)

Be careful not to pinch or cut the wires.

5. Aach the console mast and console mast cover to the main frame.

Slide console mast

cover onto the

mast.

Pull the cable out

of the top of the

main frame and

unravel and

straighten out.

Feed the cable into

the boom of the

console mast and

out the top.

Install the mast into

the receiving

bracket on the

main frame.

Install one long

hex bolt and split

washer into the

side of the bracket

and mast.

Install two short hex

head bolts and curved

washers into the front

of the console mast.

(This is shown in Step 1.2 and 1.3on page 8 in the Owner’s Manual.)

6. Aach the console to the console mounng plate.

Place the console next to the console mast plate, and then plug all of

the connectors into the back of the console.

Secure the console to the console mounng plate with four Phillips

head screws.

Be careful not to pinch or cut the wires.

(This is shown in Step 1.4 on page 8 in the Owner’s Manual.)

Note: Some deliveries

will require setup in an

upstairs room or other

location with limited

access. When this is

the case, it is recom-

mended that you

unpack the parts

outside and carry

them individually to

the customer-specied

location.

7.Attachtheleftandrighthandlebars.



     

Removefoampads

fromthehandlebar

axlebutleavethe

rubberrings.

Placeawave

washeroneach

handlebaraxle.

Slidethehandle

barsontothe

appropriatesideof

theaxle.

Attachbothhandle

barsusingtwohex

headboltsandflat

washers.

Connectthewires

on

thehandlebars

tothewiresonthe

consolemast.

Tuckthewiresinto

theconsolemast

andcoverwiththe

rubbergrommets.

(ThisisshowninStep2.1through2.4onpage10oftheOwner’sManual.)

Becarefulnottopinchorcutthewires.

8.Installthefrontandrearhandlebarcovers.

 

Placethefrontandrear

handlebarcoversover

thehandlebarandaxle,

andattachusingfour

sheetmetalscrewsper

side.



(ThisisshowninStep2.4onpage10oftheOwner’sManual.)

9.Connectthehandlebarstotheconnectingarms.

 

Aligntheholeintherod

endoftheconnecting

armswiththebrackets

onthehandlebar,and

attachusingahexhead

bolt,flatwasherand

nylonnut.

(ThisisshowinStep3onpage11oftheOwner’sManual.)

10.Installtheinnerconnectingarmcovers.



Placethecovers

overtheconnecting

armsandsecure

usingtwoPhillips

headscrewsand

twosheetmetal

screws.

(SeeStep4.1onpage12.)

11.Installtheouterconnectingarmcovers.



Placethecovers

overtheinner

coversandsecure

usingtwoPhillips

headscrewsand

twosheetmetal

screws.

(SeeStep4.1onpage12)

12.Installslidingwheelcovers.



Placethesliding

wheelcoversover

thewheelsonthe

connectingarms

andsecureusing

twoPhillipshead

screwsperside.

(SeeStep4.2onpage12)

13.Installthetwostabilizercovers.



Placethecovers

onthemiddle

stabilizerbar,and

attachwithone

Phillipshead

screwperside.

(SeeStep4.3onpage12.)

14.Installfrontstabilizercover.



Placethefront

stabilizercoveron

thefrontstabilizer

andattachusing

twoPhillipshead

screws.

(SeeStep4.4onpage12.)

15.Installtherearinclinebarcover.



Attachthetwo

inclinecover

bracketstothe

inclinerailassembly

usingfourPhillips

headscrews.

(SeeStep4.5onpage12.)

15.Installtherearinclinebarcover(cont.)

 

Placetherearinclinebar

overtherearinclinebar

andattachittotherail

baseusingfourPhillips

headscrews.

(ThisisshowninStep4.5onpage12oftheOwner’sManual.)

16.Installtherearstabilizercover.

 

Installtherearstabilizer

coverontherear

stabilizerusingfour

Phillipsheadscrews.

(ThisisshowinStep4.6onpage12oftheOwner’sManual.)

17.Installtheinclinerailfrontcover.



Placetheincline

railfrontcover

overthemiddle

stabilizertube,

andattachwith

fourPhillips

screws.

(SeeStep4.7onpage12.)

18.Plugthepowercordintothemain

frameoftheellipticaltrainer,andthen

plugthepowercordintothewalloutlet



19.Removeallpackingmaterials.



(49)__

Sole E55 Assembly Instructions Manual

Brand: Sole

Model: E55

Type: Assembly Instructions Manual

This manual is also suitable for

Download PDF

report

Sole E55 Assembly Instructions Manual

This manual is also suitable for

Sole E55 Assembly Instructions Manual

Related papers

Other documents