Kelleher F328 Installation guide

Type
Installation guide

This manual is also suitable for

Kelleher F328

The Kelleher F328 is a versatile device designed to enhance your productivity and streamline your workflow. With its advanced features and intuitive design, the F328 empowers you to tackle a wide range of tasks with ease.

Capabilities:

  • High-Resolution Scanning: Capture crisp and detailed scans of documents, images, and objects, preserving their original quality.
  • Multi-Page Feeding: Effortlessly scan multiple pages at once, saving you time and reducing the risk of errors.
  • OCR (Optical Character Recognition): Convert scanned text into editable digital formats, enabling easy editing and archiving.

Kelleher F328

The Kelleher F328 is a versatile device designed to enhance your productivity and streamline your workflow. With its advanced features and intuitive design, the F328 empowers you to tackle a wide range of tasks with ease.

Capabilities:

  • High-Resolution Scanning: Capture crisp and detailed scans of documents, images, and objects, preserving their original quality.
  • Multi-Page Feeding: Effortlessly scan multiple pages at once, saving you time and reducing the risk of errors.
  • OCR (Optical Character Recognition): Convert scanned text into editable digital formats, enabling easy editing and archiving.
HOW TO INSTALL QUARTER ROUND
Quarter round moulding is an inexpensive way to make a simple piece of baseboard look better or
provide a neat finish to a flooring job. It can also be used by itself to create a clean look in a room.
Quarter-round comes in different sizes. The most common size is 3/4-inch. When adding a piece of
quarter-round to the top of a piece of 1-inch trim, use 3/4-inch quarter-round. This would match the
top of the board perfectly. If you are placing quarter-round in front of the baseboard use any size
you prefer or that will fill any gaps between the end of your flooring and the wall
Instructions
1. Make your first cut at a 45-degree angle using your miter box and saw, then make your measurement
for the total length. If you are adding quarter-round molding to a four-cornered room, then all your cuts
will be at a 45-degree angle with the angles running towards the center of the piece of molding.
2. Make butt joints where the baseboard meets the door trim. Every room has to have at least one door
opening, so whenever you come to a door frame you can run the molding right up to the frame without
cutting an extra 45-degree angle. Just make sure the butt joint is at a perfect 90 degrees. Don' trust the
lumberyard; always cut the end of a piece of quarter-round before you place it.
3. Wrap the molding around any abutments in the wall using a 45-degree miter joint. In this case, you will
cut the angles in the exact opposite way that you did in Step 2. That means the angle begins at the
curve in the wood and runs into the center of the piece of molding at a 45-degree angle.
4. Splice together any pieces of molding with two 45-degree cuts that run in different directions. These
cuts should fit together tightly and most likely will not be noticed if they are done right.
5. Nail the molding to the floor at an angle using #6 or #8 bright-finish nails and set each nail with a small
nail set.
6. Fill each nail hole with wood putty. If necessary, you can fill the wood joints with putty, but a clean and
careful cutting job should eliminate the need for this step.
  • Page 1 1

Kelleher F328 Installation guide

Type
Installation guide
This manual is also suitable for

Kelleher F328

The Kelleher F328 is a versatile device designed to enhance your productivity and streamline your workflow. With its advanced features and intuitive design, the F328 empowers you to tackle a wide range of tasks with ease.

Capabilities:

  • High-Resolution Scanning: Capture crisp and detailed scans of documents, images, and objects, preserving their original quality.
  • Multi-Page Feeding: Effortlessly scan multiple pages at once, saving you time and reducing the risk of errors.
  • OCR (Optical Character Recognition): Convert scanned text into editable digital formats, enabling easy editing and archiving.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI