Whirlpool WFE320M0JB Installation guide

INSTALLATION INSTRUCTIONS 30" (76.0 CM)

FREESTANDING ELECTRIC RANGES

INSTRUCTIONS D’INSTALLATION

DES CUISINIÈRES ÉLECTRIQUES

AUTOPORTANTES

DE 30" (76,0 CM)

INSTRUCCIONES DE INSTALACIÓN

COCINASELÉCTRICAS INDEPENDIENTES

DE30" (76,0CM)

Table of Contents/Table des matières/Tabla de contenidos

IMPORTANT:

Save for local electrical inspector’s use.

IMPORTANT :

À conserver pour consultation par l’inspecteur local des installations électriques.

IMPORTANTE:

Guarde para tener a disposición del inspector de electricidad local.

W11333088A

RANGE SAFETY ........................................2

INSTALLATION REQUIREMENTS ............3

Tools and Parts ........................................3

Location Requirements ...........................3

Electrical Requirements- U.S.A. Only .....5

Electrical Requirements - Canada Only .. 6

INSTALLATION INSTRUCTIONS ..............6

Unpack Range.........................................6

Install Anti-Tip Bracket ............................ 7

Electrical Connection - U.S.A. Only ........ 8

Verify Anti-Tip Bracket Is Installed

andEngaged .........................................12

Level Range ...........................................13

Warming Drawer or Premium Storage

Drawer ...................................................13

Storage Drawer .....................................14

Oven Door .............................................14

Complete Installation ............................14

Moving the Range .................................15

SÉCURITÉ DE LA CUISINIÈRE ..............16

EXIGENCES D’INSTALLATION ..............17

Outillage et pièces .................................17

Exigences d’emplacement ....................17

Spécications électriques –

É.-U. seulement .....................................19

Spécications électriques –

Canada seulement ................................20

INSTRUCTIONS D’INSTALLATION ........20

Déballage de la cuisinière .....................20

Installation de la bride

antibasculement ....................................21

Raccordement électrique –

É.-U. seulemnt .......................................22

Vérier que la bride antibasculement

est bien installée et engagée ................26

Réglage de l’aplomb de la cuisinière ....27

Tiroir-réchaud ou tiroir de remisage

de qualité supérieure ............................. 27

Tiroir de remisage .................................. 28

Porte du four .........................................28

Achever l’installation .............................28

Déplacement de la cuisinière ................29

SEGURIDAD DE LA COCINA .................30

REQUISITOS DE INSTALACIÓN ............31

Herramientas y piezas ...........................31

Requisitos de ubicación ........................ 31

Requisitos eléctricos,

en EE. UU. únicamente .........................33

Requisitos eléctricos –

Solo en Canadá ..................................... 34

INSTRUCCIONES DE INSTALACIÓN ....34

Desembale la cocina ............................. 34

Instalación del soporte antivuelco ........35

Conexión eléctrica,

en EE. UU. únicamente .........................36

Verique que el soporte anti-vuelco

esté instalado y enganchado ................40

Nivelación de la cocina .........................41

Cajón de calentamiento o cajón

dealmacenamiento Premium ..............41

Cajón de almacenamiento ....................42

Puerta del horno ....................................42

Completar la instalación .......................42

Cómo mover la cocina ..........................43

2

RANGE SAFETY

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

Anti-Tip

Bracket

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

Range Foot

WARNING

3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■ Tape measure ■ Marker or pencil

■ Flat-blade screwdriver ■ Masking tape

■ Phillips screwdriver ■ 1/4" (6.4 mm) drive

ratchet

■ Level ■ 1/4" (6.4 mm) nut driver

■ Hammer ■ 3/8" (1 cm) and 5/16"

(7.9 mm) nut driver

■ Hand or electric drill ■ 1/8" (3.2 mm) drill bit

(for wood oors)

■ Wrench or pliers

Parts Supplied

Check that all parts are included.

■ Anti-tip bracket must be securely mounted to oor or wall.

Thickness of ooring may require longer screws to anchor

bracket to oor.

Parts needed

If using a power supply cord kit:

■ A UL listed power supply cord kit marked for use with

ranges. The cord should be rated at 250 V minimum, 40 A

or 50 A that is marked for use with nominal 1³⁄

8

" (3.5 cm)

diameter connection opening and must end in ring terminals

or open-end spade terminals with upturned ends.

■ A UL listed strain relief.

Check local codes. Check existing electrical supply. See

“Electrical Requirements” section.

It is recommended that all electrical connections be made

by a licensed, qualied electrical installer.

A

B

A. Anti-tip bracket

B. #12 x 1

5

/

8

" (4.1 cm) screws (2)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ It is the installer’s responsibility to comply with installation

clearances specied on the model/serial/rating plate. The

model/serial/rating plate is located on the frame behind a

top corner of the door or either side of the drawer.

■ To eliminate the risk of burns or re by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see “Install Anti-Tip Bracket”

section.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with

your builder or cabinet supplier to make sure that the materials

used will not discolor, delaminate or sustain other damage. This

oven has been designed in accordance with the requirements

of UL and CSA International and complies with the maximum

allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD Part 280). When such

standard is not applicable, use the Standard for Manufactured

Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with

the current standards CAN/CSA-Z240-latest edition, or with

local codes.

Mobile home installations require:

■ When this range is installed in a mobile home, it must be

secured according to the instructions in this document.

■ Four-wire power supply cord or cable must be used in a

mobile home installation. The appliance wiring will need

to be revised. See “Electrical Connection - U.S.A. Only”

section.

4

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and

36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood

combination above the cooking surface, follow the range hood

or microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

A freestanding range may be installed next to combustible walls

with zero clearance.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or

metal cabinet is covered by not less than 1/4" (6.4 mm) ame

retardant millboard covered with not less than No. 28 MSG

sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)

aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking

platform and the bottom of an uncovered wood or metal cabinet.

A

B

D

F

E

C

A. 13" (33.0 cm) max. upper cabinet depth

B. 30" (76.2 cm) min. opening width

C. For minimum clearance to top of cooktop, see NOTE*

D. 30" (76.2 cm) min. opening width

E. Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,

7" (17.8 cm) max. from oor.

F. Cabinet door or hinges should not extend into the cutout.

Product Dimensions

IMPORTANT: Range must be level after installation. Follow the

instructions in the “Level Range” section. Using the cooktop as

a reference for leveling the range is not recommended.

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**Front of door and drawer may extend further forward

depending on styling.

A

B

C

D

E

F

A. 27

3

/

4

" (70.5 cm) max. depth with handle

B. 46

7

/

8

" (119.1 cm) overall height (max.) with leveling legs

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs screwed

all the way in*

D. 29

7

/

8

" (75.9 cm) width

E. 25

5

/

16

" (64.3 cm) depth - back of range to front of cooktop**

F. Model/serial/rating plate (located on the frame behind a top

corner of the door or either side of the drawer)

5

Electrical Requirements

Electrical Requirements - U.S.A. Only

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

WARNING: Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check with a

qualied electrician or service technician if you are in doubt as to

whether the appliance is properly grounded. Do not modify the

power supply cord plug. If it will not t the outlet, have a proper

outlet installed by a qualied electrician.

Electrical Connection

To properly install your range, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ Range must be connected to the proper electrical voltage

and frequency as specied on the model/serial rating plate.

The model/serial rating plate is located on the frame behind

a top corner of the door or either side of the drawer. Refer

to the gures in “Product Dimensions” in the “Location

Requirements” section.

■ This range is manufactured with the neutral terminal

connected to the cabinet. Use a 3-wire, UL listed, 40- or

50A power supply cord (pigtail) (see the following Range

Rating chart). If local codes do not permit ground through

the neutral, use a 4-wire power supply cord rated at 250 V,

40 or 50 A and investigated for use with ranges.

Range Rating* Specied Rating of

Power Supply Cord Kit

and Circuit Protection

120/240 V 120/208 V Amps

8.8 - 16.5 KW

16.6 - 22.5 KW

7.8 - 12.5 KW

12.6 - 18.5 KW

40 or 50**

50

*The NEC calculated load is less than the total connected

load listed on the model/serial rating plate.

**If connecting to a 50 A circuit, use a 50 A rated cord with

kit. For 50 A rated cord kits, use kits that specify use with

a nominal 1³⁄

8

" (3.5 cm) diameter connection opening.

■ A circuit breaker is recommended.

■ The range can be connected directly to the circuit breaker

box (or fused disconnect) through exible or nonmetallic

sheathed, copper or aluminum cable. See the “Electrical

Connection - U.S.A. Only” section.

■ Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that

the range can be moved if servicing is ever necessary.

■ A UL listed conduit connector must be provided at each end

of the power supply cable (at the range and at the junction

box).

■ Wire sizes and connections must conform with the rating of

the range.

■ The wiring diagram is located on the Tech Sheet.

■ The Tech Sheet is located on the back of the range inside a

clear plastic bag.

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the

neutral by a link. The ground must be revised so the green

ground wire of the 4-wire power supply cord is connected to the

cabinet. See “Electrical Connection - U.S.A. Only” section.

Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and

recreational vehicles, or an area where local codes prohibit

grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a

matching UL listed, 4-wire, 250 V, 40 or 50 A, range power

supply cord (pigtail) must be used. This cord contains 4 copper

conductors with ring terminals or open-end spade terminals with

upturned ends, terminating in a NEMA Type 14-50P plug on the

supply end.

The fourth (grounding) conductor must be identied by a green

or green/yellow cover and the neutral conductor by a white

cover. Cord should be Type SRD or SRDT with a UL listed strain

relief and be at least 4 ft (1.22 m) long.

The minimum conductor sized for the copper 4-wire power cord

are:

40 A circuit

2 No.-8 conductors

1 No.-10 white neutral

1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire, 250 V, 40

or 50 A range power supply cord (pigtail). This cord contains 3

copper conductors with ring terminals or open-end spade

terminals with upturned ends, terminating in a NEMA Type

10-50P plug on the supply end. Connectors on the appliance

end must be provided at the point the power supply cord enters

the appliance. This uses a 3-wire receptacle of NEMA Type

10-50R.

4-wire receptacle (14-50R)

3-wire receptacle (10-50R)

6

INSTALLATION INSTRUCTIONS

Unpack Range

1. Remove shipping materials, tape and lm from range.

2. Remove oven racks and parts package from inside oven.

3. Do not remove the shipping base at this time.

4. On Ranges Equipped with a Storage Drawer:

Remove the storage drawer. See the “Storage Drawer”

section. Use a 1/4" (6.4 mm) drive ratchet to lower the rear

leveling legs one-half turn. Use a wrench or pliers to lower

front leveling legs one-half turn.

On Ranges Equipped with a Warming Drawer or Premium

Storage Drawer:

On ranges equipped with a warming drawer or premium

storage drawer, the rear legs cannot be accessed by

removing the warming drawer or premium storage drawer. It

will be necessary to adjust the rear legs from outside the

range. Use wrench or pliers to lower the front and rear

leveling legs one half turn.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

A

A. Shipping base

C

D

A

B

A. 1/4" (6.4 mm) drive ratchet

B. Rear leveling leg

C. Wrench or pliers

D. Front leveling leg

B

C

A

A. Rear leveling leg

B. Wrench or pliers

C. Front leveling leg

Electrical Requirements - Canada Only

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrical installer determine that

the ground path is adequate and wire gauge are in accordance

with local codes.

Be sure that the electrical connection and wire size are adequate

and in conformance with CSA Standard C22.1, Canadian

Electrical Code, Part 1 - latest edition, and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association

178 Rexdale Blvd.

Toronto, ON M9W 1R3 CANADA

■ Check with a qualied electrical installer if you are not sure

the range is properly grounded.

Range Rating* Specied Rating of

Power Supply Cord Kit

and Circuit Protection

120/240 V 120/208 V Amps

8.8 - 16.5 KW

16.6 - 22.5 KW

7.8 - 12.5 KW

12.6 - 18.5 KW

40 or 50**

50

*The NEC calculated load is less than the total connected load

listed on the model/serial/rating plate.

**If connecting to a 50 A circuit, use a 50 A rated cord with

kit. For 50 A rated cord kits, use kits that specify use with a

nominal 1

3

/

8

" (3.5 cm) diameter connection opening.

■ A time-delay fuse or circuit breaker is recommended.

■ This range is equipped with a CSA International Certied

Power Cord intended to be plugged into a standard 14-50R

wall receptacle. Be sure the wall receptacle is within reach of

range’s nal location.

■ Do not use an extension cord.

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or

electrical shock.

7

Install Anti-Tip Bracket

1. Remove the anti-tip bracket from where it is taped inside the

storage drawer or warming drawer.

2. Determine which mounting method to use: oor or wall.

If you have a stone or masonry oor, you can use the wall

mounting method. If you are installing the range in a mobile

home, you must secure the range to the oor.

3. Determine and mark centerline of the cutout space. The

mounting can be installed on either the left-side or right-side

of the cutout. Position mounting bracket against the wall in the

cutout so that the V-notch of the bracket is 12

9

/

16

" (31.9 cm)

from centerline as shown.

4. Drill two 1/8" (3 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following

illustrations.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

Centerline

B

A

A. 12

9

/

16

" (31.9 cm)

B. Bracket V-notch

Floor Mounting

Wall Mounting

5. Using the Phillips screwdriver, mount anti-tip bracket to

the wall or oor with the two #12 x 1

5

/

8

" (4.1 cm) screws

provided.

6. Move range close enough to opening to allow for nal

electrical connections. Remove shipping base, cardboard

or hardboard from under range.

7. Move range into its nal location, making sure rear leveling

leg slides into anti-tip bracket.

8. Move range forward onto shipping base, cardboard or

hardboard to continue installing the range using the following

installation instructions.

Rear position

Front position

Diagonal (2 options)

8

Power Supply Cord

1. Disconnect power.

2. Remove the terminal block cover screws located on the back

of the range. Pull cover down and toward you to remove

cover from range.

3. Depending on your model, remove the plastic tag holding

three 10-32 hex nuts from the middle post of the terminal

block.

Direct Wire

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use a new 40 amp power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions can result in death,

fire, or electrical shock.

A

B

C

A. Two mounting tabs each side

B. Terminal block cover

C. Hex-head screws

Electrical Connection - U.S.A. Only

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death,

fire, or electrical shock.

OR

Remove the top 10-32 hex nut from each of the 3 terminal

blocks and set aside.

4. Add strain relief.

Style 1: Power supply cord strain relief

■ Remove the knockout for the power supply cord.

■ Assemble a UL Listed strain relief in the opening.

■ Tighten strain relief screw against the power supply cord.

A

A. UL Listed strain relief

9

Style 2: Direct wire strain relief

■ Remove the knockout as needed for the exible conduit

connection.

■ Assemble a UL listed conduit connector in the opening.

■ Tighten strain relief screw against the exible conduit.

5. Complete installation following instructions for your type of

electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has:

And you will be

connecting to:

Go to Section:

4-wire receptacle

(NEMA type 14-50R)

A UL Listed, 250V

minimum, 40 A,

range power supply

cord

4-wire

connection:

Power supply

cord

4-wire direct A circuit breaker

box or fused

disconnect

4-wire

connection:

Direct wire

3-wire receptacle

(NEMA type 10-50R)

A UL Listed, 250V

minimum, 40 A,

range power supply

cord

3-wire

connection:

Power supply

cord

3-wire direct A circuit breaker

box or fused

disconnect

3-wire

connection:

Direct wire

A

B

A. Removable retaining nut

B. Conduit

4-wire connection: Power Supply Cord

Use this method for:

■ New branch-circuit installations (1996 NEC)

■ Mobile homes

■ Recreational vehicles

■ In an area where local codes prohibit grounding through the

neutral

1. Part of metal ground strap must be cut out and removed.

2. Use a Phillips screwdriver to remove the ground-link screw

from the back of the range. Save the ground-link screw and

the end of the ground link under the screw.

3. Feed the power supply cord through the strain relief on the

cord/conduit plate on bottom of range. Allow enough slack

to easily attach the wiring to the terminal block.

A

B

C

A. Metal ground strap

B. Discard

C. Ground-link screw

A

B

D

C

A. Terminal block

B. Ground-link screw

C. UL listed strain relief

D. Power supply cord wirest

(12.7 cm)

5"

3/8"

(1.0 cm)

3"

(7.6 cm)

3/8"

(1.0 cm)

10

4. Use a Phillips screwdriver to connect the green ground wire

from the power supply cord to the range with the ground-

link screw and ground-link section. The ground wire must be

attached rst.

5. Use 3/8" (1.0 cm) nut driver to connect the neutral (white)

wire to the center terminal block post with one of the 10–32

hex nuts.

6. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

7. Securely tighten hex nuts.

NOTE: For power supply cord replacement, use only a

power cord rated at 250 V minimum, 40 A or 50 A that

is marked for use with nominal 1³⁄

8

" (3.5 cm) diameter

connection opening, with ring terminals and marked for use

with ranges.

8. Tighten strain relief screws.

9. Replace terminal block access cover.

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting chassis

ground conductor to neutral wire of power supply cord.

1. Feed the power supply cord through the strain relief on the

cord/conduit plate on bottom of range. Allow enough slack

to easily attach the wiring to the terminal block.

2. Use 3/8" (1.0 cm) nut driver to connect the neutral (white)

wire to the center terminal block post with one of the 10–32

hex nuts.

3. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

4. Securely tighten hex nuts.

NOTE: For power supply cord replacement, use only a

power cord rated at 250 V minimum, 40 A or 50 A that

is marked for use with nominal 1³⁄

8

" (3.5 cm) diameter

connection opening, with ring terminals and marked for use

with ranges.

5. Tighten strain relief screws.

6. Replace terminal block access cover.

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or

circuit breaker box. Depending on your electrical supply, make

the required 3-wire or 4-wire connection.

1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip

the insulation back 3/8" (1.0 cm) from the end of each wire.

2. Allow enough slack in the wire to easily attach the wiring

terminal block.

3. Complete electrical connection according to your type of

electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

■ New branch-circuit installations (1996 NEC)

■ Mobile homes

■ Recreational vehicles

■ In an area where local codes prohibit grounding through the

neutral

A

B

C

F

D

E

A. 10–32 hex nut

B. Ground-link screw

C. Line 2 (red)

D. Green ground wire

E. Neutral (center) wire

F. Line 1 (black)

A

B

D

C

A. Terminal block

B. Ground-link screw

C. UL listed strain relief

D. Power supply cord wires - large opening

A

B

C

D

E

A. 10–32 hex nut

B. Line 2 (red)

C. Ground-link screw

D. Neutral (white) wire

E. Line 1 (black)

3"

(7.6 cm)

³⁄₈"

(1.0 cm)

11

1. Part of metal ground strap must be cut out and removed.

2. Use a Phillips screwdriver to remove the ground-link screw

from the back of the range. Save the ground-link screw and

the end of the ground link under the screw.

3. Pull the wires through the strain relief on bottom of range.

Allow enough slack to easily attach wiring to the terminal

block.

4. Attach terminal lugs to line 1 (black), neutral (white), and line

2 (red) wires. Loosen (do not remove) the setscrew on the

front of the terminal lug and insert exposed wire end through

bottom of terminal lugs. Securely tighten setscrew to torque

as shown in the following Bare Wire Torque Specications

chart.

Bare Wire Torque Specications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3

N-m).

Wire Awg Torque

8 gauge copper 25 lbs-in. (2.8 N-m)

6 gauge aluminum 35 lbs-in. (4.0 N-m)

5. Use a hex or Phillips screwdriver to connect the bare (green)

ground wire to the range with the ground-link screw and

ground-link section. The ground wire must be attached rst

and must not contact any other terminal.

6. Use 3/8" (1.0 cm) nut driver to connect the neutral (white)

wire to the center terminal block post with one of the 10–32

hex nuts.

7. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

8. Securely tighten hex nuts.

9. Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground

conductor to neutral supply wire.

1. Pull the wires through the conduit on cord/conduit plate on

bottom of range. Allow enough slack to easily attach the

wiring to the terminal block.

A

B

C

A. Metal ground strap

B. Discard

C. Ground-link screw

A

B

C

D

E

G

F

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Bare (green)

ground wire

E. Line 2 (red) wire

F. Neutral (white) wire

G. Line 1 (black) wire

A

B

C

DE

A. Terminal lug

B. Setscrew

C. Line 2 (red) wire

D. Neutral (white) wire

E. Line 1 (black) wire

B

A

G

E

C

D

F

A. 10–32 hex nut

B. Line 2 (red)

C. Bare (green) ground wire

D. Ground-link screw

E. Neutral (white) wire

F. Line 1 (black)

G. Terminal lug

A

B

C

D

E

F

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Line 2 (red) wire

E. Bare (green) ground wire

F. Line 1 (black) wire

12

2. Attach terminal lugs to line 2 (red), bare (green) ground, and

line 1 (black) wires. Loosen (do not remove) the setscrew on

the front of the terminal lug and insert exposed wire end

through bottom of terminal lugs. Securely tighten setscrew to

torque as shown in the following Bare Wire Torque

Specications chart.

Bare Wire Torque Specications

Attaching terminal lugs to the terminal block - 20 lbs-in.

(2.3N-m).

Wire Awg Torque

8 gauge copper 25 lbs-in. (2.8 N-m)

6 gauge aluminum 35 lbs-in. (4.0 N-m)

3. Use 3/8" (1.0 cm) nut driver to connect the bare (green)

ground wire to the center terminal block post with one of the

10–32 hex nuts.

4. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

6. Replace terminal block access cover.

Verify Anti-Tip Bracket Is Installed

and Engaged

On Ranges Equipped with a Storage Drawer:

1. Remove the storage drawer. See the “Storage Drawer” section.

2. Use a ashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges Equipped with a Warming Drawer

or Premium Storage Drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer or premium storage drawer, and grasp the

lower right or left side of the control panel as shown.

NOTE: If your countertop is mounted with a backsplash, it

may be necessary to grasp the range higher than is shown

in the illustration.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than 1/2" (1.3 cm) off the oor

without resistance, stop tilting the range and lower it gently back

to the oor. The range foot is not engaged in the anti-tip bracket.

IMPORTANT: If there is a snapping or popping sound when

lifting the range, the range may not be fully engaged in the

bracket. Check to see if there are obstructions keeping the range

from sliding to the wall or keeping the range foot from sliding

into the bracket. Verify that the bracket is held securely in place

by the mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket

is securely attached to the oor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. If you

need assistance or service, refer to the “Assistance or Service”

section of the Use and Care Guide, or the cover or “Warranty”

section of the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than 1/2" (1.3 cm) off the oor

without resistance, the anti-tip bracket may not be installed

correctly. Do not operate the range without anti-tip bracket

installed and engaged. Please reference the “Assistance or

Service” section of the Use and Care Guide, or the cover or

“Warranty” section of the User Instructions, to contact service.

A

B

C

DE

A. Terminal lug

B. Setscrew

C. Line 2 (red) wire

D. Bare (green) ground wire

E. Line 1 (black) wire

B

F

A

E

D

C

A. 10–32 hex nut

B. Line 2 (red)

C. Ground-link screw

D. Bare (green) ground wire

E. Line 1 (black)

F. Terminal lug

13

Level Range

Determine if you have AquaLift

®

Technology or Steam Clean by

referring to the “Range Care” section of the User Instructions.

For Ranges with AquaLift

®

Technology or Steam Clean:

1. Place level on the oven bottom as indicated in one of the two

gures below depending on the size of the level. Check with

the level: side-to-side and front to back.

2. If range is not level, pull range forward until rear-leveling leg

is removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

For Ranges without AquaLift

®

Technology

or Steam Clean:

1. Place a standard at rack in oven.

2. Place level on the rack and check levelness of the range, rst

side-to-side; then front to back.

3. If range is not level, pull range forward until rear leveling leg

is removed from the anti-tip bracket.

4. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

Style 1: Ranges Equipped with a Storage Drawer:

Use a 1/4" (6.4 mm) drive ratchet, wrench or pliers to adjust

leveling legs up or down until the range is level. Push range

back into position. Check that rear leveling leg is engaged in

the anti-tip bracket.

Style 2: Ranges Equipped with a Warming Drawer

or Premium Storage Drawer:

Use a wrench or pliers to adjust leveling legs up or down

until the range is level. Push range back into position. Check

that rear-leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking

performance and best cleaning results using AquaLift

®

Technology and Steam Clean functions.

Warming Drawer or Premium

Storage Drawer

(on some models)

Remove all items from inside the warming drawer or premium

storage drawer, and allow the range to cool completely before

attempting to remove the drawer.

To Remove:

1. Open the warming drawer or premium storage drawer to its

fully open position.

2. Using a at-blade screwdriver, gently loosen the warming

drawer or premium storage drawer from the glide alignment

notch and lift up the drawer alignment tab from the glide.

3. Repeat Step 2 on the other side. The warming drawer or

premium storage drawer is no longer attached to the drawer

glides. Using both hands, pick up the warming drawer or

premium storage drawer to complete the removal.

To Replace:

1. Align the forward drawer notches with the notches in the

drawer glides on both sides. Place the rear alignment tabs

into the drawer glides on both sides.

2. Push the warming drawer or premium storage drawer in all

the way.

3. Gently open and close the warming drawer or premium

storage drawer to ensure it is seated properly on the glides

on both sides

A

B

C

A. Flat-blade screwdriver

B. Drawer alignment tab

C. Drawer glide notch

A

B

A. Drawer alignment tab

B. Drawer glide notch

14

Storage Drawer

(on some models)

The storage drawer can be removed. Before removing, make

sure drawer is cool and empty.

To Remove:

1. Pull the storage drawer straight back to the drawer stop.

2. Lift up the front of the drawer and pull the drawer out.

To Replace:

1. Lift up the front of the drawer and place the rear of the

drawer inside the range so that the drawer stop notch is

behind the drawer glide.

2. Lower the drawer so that the edge of the slide rail drops into

the slot in the drawer glide.

3. Slowly push the drawer into the range.

NOTE: When properly installed, the rear slides on the bottom

of the drawer will engage the base rails and the drawer will

not tip when items are placed in the drawer.

Oven Door

For normal range use, it is not suggested to remove the oven

door. However, if removal is necessary, make sure the oven is off

and cool. Then, follow these instructions. The oven door is heavy.

To Remove:

1. Open oven door all the way.

2. Pinch the hinge latch between two ngers and pull forward.

Repeat on other side of oven door.

A

A. Drawer stop notch

A

A. Engage drawer glide.

A

A. Hinge latch

3. Close the oven door as far as it will shut.

4. Lift the oven door while holding both sides.

Continue to push the oven door closed and pull it away from

the oven doorframe.

To Replace:

1. Insert both hanger arms into the door.

2. Open the oven door.

You should hear a “click” as the door is set into place.

3. Move the hinge levers back to the locked position. Check

that the door is free to open and close. If it is not, repeat

the removal and installation procedures.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See the “Level Range” section.

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, read

the “Range Care” section of the Use and Care Guide or User

Instructions.

6. Read the “Range Use” section of the Use and Care Guide or

User Instructions.

7. Plug power cord into appropriate outlet. Turn power on.

8. Turn on surface burners and oven. See the Use and Care

Guide or User Instructions for specic instruction on range

operation.

15

If range does not operate, check the following:

■ Household fuse is intact and tight; or circuit breaker has

not tripped.

■ Range is plugged into an outlet.

■ Electrical supply is connected.

IMPORTANT: If the range control displays an F9 or F9, E0

error code, the electrical outlet may be miswired. Contact

a qualied electrician to verify the electrical supply.

■ See “Troubleshooting” in the Use and Care Guide or User

Instructions.

When the range has been on for 5 minutes, check for heat. If

range is cold, turn off the range and contact a qualied technician.

Moving the Range

When moving range, slide range onto cardboard or hardboard to

avoid damaging the oor covering.

If removing the range is necessary for cleaning or maintenance:

For power supply cord-connected ranges:

1. Slide range forward.

2. Unplug the power supply cord.

3. Complete cleaning or maintenance.

4. Plug in power supply cord.

5. Check that the anti-tip bracket is installed and engaged. See

the “Verify Anti-Tip Bracket Is Installed and Engaged” section.

6. Check that range is level.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

For direct-wired ranges:

1. Disconnect power.

2. Slide range forward.

3. Complete cleaning or maintenance.

4. Check that the anti-tip bracket is installed and engaged.

See the “Verify Anti-Tip Bracket Is Installed and Engaged”

section.

5. Check that range is level.

6. Reconnect power.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Page is loading ...

Whirlpool WFE320M0JB Installation guide

Whirlpool WFE320M0JB Installation guide

in other languages

Related papers

Other documents