Ohlins YA709 Mounting Instruction

Type
Mounting Instruction
© Öhlins Racing AB. All rights reserved. Any re-
printing or unauthorized use without the written
permission of Öhlins Racing AB is prohibited.
Printed in Sweden.
Mounting Instructions YA709_1 Issued 2007 03 12
These instructions and other documents
can be downloaded from
www.ohlins.com
Mounting Instructions
Kit Contents:
Part no. Pcs.
Shock absorber YA709 1
Bracket 20030-01 1
Spacer 20047-01 1
Screw K6S M6x12 05404-01 2
Screw K6S M6x40 05404-08 1
Öhlins Sticker black 00191-13 2
Öhlins Sticker white 00191-20 2
Memo Notes Sticker 01180-01 1
Owner’s Manual 07241-02 1
Before installing this shock absorber,
check the contents of the kit listed
below. If anything is missing, please
contact your nearest Öhlins dealer.
SHOCK ABSORBER YA709
for Yamaha XVS650A DragStar Classic
Before installing this product, read the Öhlins Owner’s Manual!
I
ns
t
a
ll
in
g
a
s
ho
c
k
a
b
s
o
r
b
e
r
t
h
a
t
is
no
t
a
pp
r
o
v
ed
b
y
t
h
e
v
e
h
ic
le
m
an
u
fa
ct
ur
e
r
m
a
y
a
f
f
e
c
t t
h
e
sta
b
il
it
y
of
yo
u
r
ve
h
i
cl
e.
In
st
a
ll
ing
a
s
ho
c
k
a
b
s
o
r
ber
t
h
a
t
is
not
a
p
pr
ov
e
d
b
y
t
h
e
v
e
h
ic
l
e
m
a
n
u
fac
ture
r
m
a
y
a
f
f
e
c
t t
h
e
s
ta
b
i
l
it
y
of
y
ou
r
v
e
h
i
c
le
.
I
nst
a
lling
a
sh
o
c
k
a
b
s
o
rb
e
r
t
ha
t
is
n
o
t
a
p
p
r
o
v
ed
b
y
the
ve
h
ic
le
m
a
n
u
fa
c
t
u
r
e
r
m
ay
af
fe
ct
th
e
s
t
a
b
il
it
y
of
y
ou
r
ve
h
ic
le
.
In
sta
ll
ing
a s
h
oc
k a
b
s
orbe
r
t
h
a
t
is
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
veh
ic
l
e
m
a
n
u
fa
c
tur
e
r
m
ay
af
fec
t th
e
sta
b
il
it
y o
f
y
o
u
r v
e
h
ic
le
.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00 Fax +46 8 590 025 80
www.ohlins.com
WITH SET-UP DATA
During storage and transportation,
especially at high ambient tempera-
ture, some of the oil and grease used
for assembling may leak and stain
the packaging. This is in no way det-
rimental to the product, wipe off the
excessive oil/grease with a cloth.
Always ensure that the basic settings made by
Öhlins are intact.
Set-up Data
Spring preload 10 mm
Rebound damping 16 clicks
Shock absorber length 276,5
+0
mm
Stroke 34,5 mm
Spring 21012-54
Free spring length 120
+0
mm
ADJUSTMENTS
1
2
3
1
2
3
-12
-3
Spring Preload
Turn the knob on the hydraulic preload
adjuster to set the spring preload. Turn
clockwise to increase the preload, turn
counter clockwise to deacrease it.
Rebound
Turn the wheel on the piston shaft above
the end eye/bracket. Turn clockwise to
increase damping, turn counter clockwise
to decrease.
NOTE!
When delivered the Öhlins shock absorber
is dialed to the recommended settings
for the specifi c vehicle model. If you have
changed the setting, reset according to the
following:
The adjuster has a right hand thread. Turn
the adjuster clockwise to fully closed (pos.
zero [0]). Turn counter clockwise to open
and count the clicks until you reach the
recommended number (see Set-up Data).
CAUTION!
Do not use force, delicate sealing surfaces
can be damaged. Handtighten only.
Length
We recommend you to adjust the length
before installing the shock absorber to
the vehicle. Use two wrenches. Hold the
upper nut with one hand and at the same
time loosen the lock nut (lower nut). Turn
the end eye/ bracket to the desired length.
Lock the lock nut.
Tightening torque: 40 Nm
WARNING!
The adjustable end eye/bracket must not be
threaded out more than that the groove is fully
visible beneath the lock nut. This is maximum
length. After adjusting, make sure that the lock
nut is tightened.
HOW TO INSTALL
1
Put the motorcycle on a workstand so that the
rear wheel barely touches the ground.
WARNING!
Make sure the vehicle is securely supported so
that it will not tip.
2
Remove the seats. Consult your vehicle service
manual.
3
Remove the right side cover.
4
Remove the left side cover and the engine
cover.
5
Remove the tool box and the mud fl ap.
7
Install the Öhlins shock absorber. Make sure
that the shock absorber fi ll screw is at the top
and pointing towards the rear. Lead the hy-
draulic preload adjuster hose above the shock
absorber out to the left side of the vehicle. See
gure. Temporarily leave it while attaching the
shock absorber.
8
Fasten the front and the rear shock absorber
attachments, do not tighten yet.
9
Tighten the front and rear shock absorber at-
tachments.
NOTE!
Lower the motorcycle so that the shock
absorber is slightly compressed, before tighten-
ing the screws.
NOTE!
Recommendation! Before installing the Öhlins
shock absorber:
• clean the vehicle thoroughly
• adjust the length of the shock absorber (check
the headlight angle after adjusting the length!)
10
Reinstall the mud fl ap and the tool box.
NOTE!
The hydraulic preload adjuster hose should be
lead through the cavity of the tool box as indi-
cated in the fi gure.
11
Replace the upper left screw of the engine
cover with the bracket, spacer and screw pro-
vided in this kit. Reinstall the engine cover with
the original three screws.
12
Attach the hydraulic preload adjuster to the
bracket on the engine cover. Make sure that it
is horizontal (See fi gure 11).
1
2
5
6
Remove the front and the rear attachments of
the original shock absorber and remove it.
WARNING!
It is advisable to have an Öhlins dealer install the
shock absorber.
WARNING!
Make sure that the hydraulic preload adjuster
hose runs in soft bends. Also check that it does
not come in contact with the exhaust pipe or
any sharp edges.
4
13
Reinstall the side covers and the seats. Make
sure that all removed parts are installed in the
same way as they were before the installation.
NOTE!
Make sure that all screws are tightened to the
correct torque and that nothing fouls or restricts
movement of the shock absorber when the sus-
pension is being fully compressed or extended.
7
11
Fill screw
NOTE!
  • Page 1 1
  • Page 2 2

Ohlins YA709 Mounting Instruction

Type
Mounting Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI