Ohlins FGYA304 Mounting Instruction

Category
Motorcycles
Type
Mounting Instruction
Owners Manual
Mounting instruction Öhlins front fork kit
FG YA 304 for Yamaha YZ 2003
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB is prohibited. Printed in Sweden.
Rebound damping
adjuster
Compression
damping adjuster
Öhlins front fork MX
Your Öhlins front fork MX 2003 is an upside down
type front fork featuring the following adjusters.
Compression damping adjuster
Adjustments are made at the bottom of the front
fork leg. Use a flat screw driver.
Rebound damping adjuster
Adjustments are made at the top of the fork leg.
Use a flat screw driver.
Spring preload adjuster
Adjustments are made by turning the nut at the top
of the fork leg. Clockwise for harder adjustment,
counter clockwise too release the preload.
Use a 17 mm key.
NOTE!
When delivered the Öhlins front fork is dialed to
recommended settings for the specific brand and
make of the motorcycle. If you have changed the
setting check like this:
The adjusters have a normal right hand tread. Turn
the damping adjusters clockwise to fully closed (pos.
zero [0]). Turn counter clockwise to open and count
the clicks until you reach the recommended number
of clicks. See Setup data at page 4.
CAUTION!
Do not use to much force, delicate sealing surfaces
can be damaged.
Spring preload
adjuster
Checking sag and ride height
Front suspension
F1. Bike on a stand with the
suspension fully extended = ............
F2. Bike on the ground without rider = ............
F3. Bike on the ground with rider = ............
Free sag
F1 - F2 = ............
Ride height
F1 - F3 = ............
Rear suspension
R1.Bike on a stand with the
suspension fully extended = ............
R2.Bike on the ground without rider = ........... .
R3.Bike on the ground with rider = ............
Free sag
R1 - R2 = ............
Ride height
R1 - R3 = ............
NOTE!
If ride height is higher than recommended,
softer spring/springs must be used.
If ride height is lower than recommended,
harder spring/springs must be used.
Contact your Öhlins dealer for advice.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00. Fax +46 8 590 025 80.
www.ohlins.com
Part No. FG YA 304. Issued 03 02 13
Setup data
Lenght 938 mm
Stroke 300 mm
Rebound adjuster 14 clicks
Compression adjuster 14 clicks
Spring preload 3 mm
Front fork oil level 110 mm
Front fork position 4 mm
Bike on a stand. Bike on the ground. Bike with rider on.
F1
R1
F2
R2
F3
R3
Fork position is
measured from
the top of the fork
leg, to the top
surface of the
triple clamp.
x mm
Oil level
Oil level is
measured from
the top of the
outer leg, with the
top nut off, the
fork fully
compressed and
no spring
installed.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your suspen-
sion and this manual. Please consult your Öhlins
dealer if you have any questions with regard to
the contents of the manual.
NOTE!
During storage and transportation, espe-
cially at high ambient temperature, the oil
and grease used for assembling may run out
inside the packing and damage the
expanded polystyrene packing material. This
is not unusual and is in no way detrimental
to the shock absorber.
Kit contents
Before installing the suspension components,
please check the contents of the kit, listed on
the front page of this instruction. If anything is
missing, contact your Öhlins dealer.
Description Part No. Pcs.
Front fork type FG YA 304
Spring (4.1 N/mm) 02328-41 2
Spring (4.3 N/mm)*
Spring (4.5 N/mm) 02328-45 2
Pre-load tube 02386-01 2
Spring support 02387-01 2
Fork leg cover 02309-80 1 pair
Bolts for cover, M6x12 02314-01 6
Sticker Öhlins 00197-01 2
Owner´s Manual 1
* Use a 4.1 N/mm spring in one leg and
a 4.5 N/mm in the other.
Before installation
Öhlins Racing AB can not be held responsible for
any damage whatsoever to suspension components
or vehicle, or injury to persons, if the instructions for
fitting and maintenance are not followed exactly.
Similarly, the warranty will become null and void if
the instructions are not adhered to.
WARNING!
1. Installing suspension components, that is
not approved by the vehicle manufacturer,
may affect the stability of your vehicle. Öhlins
Racing AB cannot be held responsible for
any personal injury or damage whatsoever
that may occur after fitting the suspension
components. Contact an Öhlins dealer or
other qualified person for advice.
2. Please study and make certain that you
fully understand all the mounting instructions
and the owners manuals before handling this
suspension components kit. If you have any
questions regarding proper installation
procedures, contact an Öhlins dealer or other
qualified person.
3. The vehicle service manual must be
referred to when installing the Öhlins
suspension components
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special
precautions must be taken to avoid
damage to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Notes
WARNING!
1. It’s advisable to have an Öhlins dealer or other
qualified person to fit your front fork.
2. Instructions in the motorcycle workshop manual
are to be followed when removing the front fork.
3. When working on the motorcycle it must be
securely supported to prevent it from falling over.
Mounting Instructions
1
Put the bike on a stand so the front wheel has
ground clearance. Make sure it’s steadily positioned
and will not fall over.
2
Remove the front wheel, protecting covers and
the brake caliper. Let the caliper stay fitted to the
brake hose.
3
Remove the original fork legs and fit the Öhlins
fork legs to the triple clamps.
CAUTION!
Do not overtighten the clamps. There is a risk of
deforming the fork leg tubes. See the motorcycle’s
Workshop manual for correct torques.
NOTE!
The front fork legs must be aligned be-
fore the front wheel axle is tightened.
2
3
2
5
Upper triple clamp
Lower triple clamp
Front leg cover
Brake
caliper
Caliper
protection
cover
Front fork leg
Front wheel
6
Tighten the wheel axle and refit the removed pro-
tecting covers. Fit the Öhlins front leg covers.
NOTE!
Make sure that all bolts are tightened to the correct
torque and that nothing restrains the front fork when
the suspension is been fully compressed. See the
motorcycles workshop manual.
7
Continue your work with adjustments, see Öhlins
Owner’s Manual.
NOTE!
Before you continue, make sure that the front
springs are installed. If they are not, proceed with
the instructions at page 4 – Installing springs.
4
Put the wheel back in position. Reassemble the
brake and fit the hose holder.
NOTE!
Do not tighten the front wheel axle before the
front legs are aligned. (5)
5
Let the motorcycle stand on the ground and com-
press the front suspension as hard as possible a
couple of times. This will align the fork legs.
NOTE!
Another way to align the front legs is to rotate
the front wheel as fast as possible and bring it to
a fast stop by braking.
Notes
Installing springs
1
Put the bike on a stand and loosen the screws in
the fork top crown that hold the fork legs.
NOTE!
On most MX-bikes you have to take the handle
bar off before you can unscrew the top cap.
Unscrew the top cap, using top cap tool 1761-02.
2
NOTE!
Closing the compression and the rebound valves
will keep the damper rod extended, making it
easier to install the new spring.
Pull out the damper rod as far as possible.
Close the compression and the rebound valve
(clockwise).
Tool 1761-02
Top cap
Fork leg
Flat
screwdriver
Guide sleeve
3
Install the the correct spring. Two pairs of springs
are provided – spring ratio 4.1 N/mm and 4.5 N/
mm, respectively.
NOTE!
A spring ratio of 4.3 N/mm is obtained if a 4.1 N/mm
spring is used in one leg and a 4.5 N/mm spring in
the other leg.
4
Reinstall the spring support, the pre-load tube
and the top nut.
Spring
Top cap
Pre-load tube
Spring support
4
3
1
2
5
Install the fork top cap. Tighten (30 Nm) the top
cap and the lock nut against each other, use a
17 mm and 24 mm wrench.
Adjust the compression and the rebound valves
according to specification card.
17 mm
wrench
24 mm
wrench
5
CAUTION!
Do not overtighten the clamps. There is a risk of
deforming the fork leg tubes. See the motorcycle’s
Workshop manual for correct torques.
7
Tighten the screws in the fork top crown.
6
Refit the top cap and tighten. Use top cap tool
1761-02.
The top cap should not be tightened hard, only
turned in position by hand.
Tool
1761-02
6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ohlins FGYA304 Mounting Instruction

Category
Motorcycles
Type
Mounting Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI