165mm+-2
122mm+-2
165mm+-2 165mm+-2
4
3
6
1 2
5
122mm+-2
4
1
122mm+-2
122mm+-2
Quick Start Guide
Do not try to open the camera by yourself which may cause damage to the camera or electric shock.
Do not fire the flash in a close distance (less than 1 meter) to human eyes.
Keep the camera away from the reach of children or animals to prevent them from swallowing the batteries or small accessories.
Avoid using the camera if any form of liquid enters the camera. If it happens, switch off the camera and contact the company that you
bought this camera from for help.
Do not operate this camera with wet hands which may cause electric shock.
Do not place or store the camera in a high temperature environment which may cause damage to the camera.
Do not mix to use different types of batteries or new and old batteries.
Take out the batteries to avoid electricity leakage which may damage the camera when the camera is not in use for a long period.
Unplug the camera from the adapter (if used) to avoid damage to the camera if the camera is not to be used in a long period.
It's normal that the temperature of the camera body rises after using for a long period.
Photo Frame
Focus Range
(
)M
acro
Memory Card
Digital Zoom
Exposure
Date
Image Quality
( )Super fine
( )Fine
( )Normal
White Balance
(
)
Auto
(
)
Daylight
(
)
Sunset
( )Fluorescent
( )Tungsten
AUTO
Voice Memo
4
Battery Status
( )Battery full
( )Battery half
drained
( )Battery
drained
1
Working Mode
( )Shooting mode
( )Playback mode
( )Movie clip m
ode
( )Setup mode
2
3
5
6
7
8
Image Size
( )2048x1536
( )1600x1200
( )1280x960
( )2560x1920
9
Flash Mode
(
)
Auto flash
(
)
Auto flash with
red-eye
reduction
( )Slow Sync
( )Flash off
11
13
Icon IntroductionIcon Introduction
10
12
4
0006
2003/10/30
+
X4
X1
+0.5
1
2
3
4
5
6
7
8
9
11
12
13
1
10
3
1.Switch on the power.
2.Set the Mode Dial at Shooting Mode ( ) for still image or Movie Clip Mode ( ) for video recording.
3.The setting of the focus range for still image capture is required as follows
Macro ( ) : 0.3m
Normal ( ): 1.4m~infinity
4.Refer to the User Manual -- Advanced Functionality Settings (page10)to set up the features based on your needs.
5.Hold still and press down the Shutter Button.
6.The LED Indicator starts blinking right after the Shutter Button is released.
7.Once the LED Indicator stops blinking, you are ready to take another shot.
Note
A message of "Low Light!" appearing on the TFT LCD Monitor as a warning is to remind you that the image that you are going to
capture is under a low light environment. To compose a good quality image, it is strongly recommended to go to the Flash Mode and
select Auto Flash to supply more light sources.
Basic Photography
Slide the "POWER" switch sideways and hold it awhile to switch on the camera.
Repeat the action above to switch off the camera.
1. Check if the camera is switched off.
2. Slide the Battery / Memory Card Cover out to open it.
3. Load 2 x AA batteries into the battery chamber, following the
polarity indication.
4. Close the Battery / Memory Card Cover.
Switch On or Off the Camera
Loading the Batteries
PC Connection
6
CARD FULL
MEMORY FULL
CARD LOCKED
(ICON BLINKING)
LOCK
NO IMAGE
FILE ERROR
MEMORY ERROR
CARD ERROR
LOW BATTERY !
(ICON BLINKING)
HAND SHAKE
ICON ( )
There is insufficient card memory capacity
to store an image.
There is insufficient internal memory
capacity to store an image.
The SD card is under protection.
The Image can't be deleted under protection.
There is no image stored in the memory card
or built-in flash memory.
File format error.
Memory is damaged or failed.
Card is damaged or failed.
Battery power is drained.
The environment is too dark in "Flash Off"
mode.
Delete the stored image(s) in the memory
card or insert a new memory card.
Delete the stored image(s) in the flash
memory.
Set the card protection switch at non-
protection position.
Unlock the protected image.
Please take pictures or record movie
clips.
Insert a new SD/MMC card or
format the media.
Format the media.
Insert a new SD/MMC card
Insert new batteries.
Cancel the Flash off mode.
Messages Causes Solutions
Safety Notes
1
Installing the Camera's Driver
Installing Ulead Photo Explorer
Downloading the image(s)
Please refer to the User Manual for the details.
Please refer to the User Manual for the details.
Please refer to the User Manual for the details.
1. Switch off the camera.
2. Open the Battery / Memory Card Cover.
3. Insert the SD card into the card slot and press it down until a click
sound happens.
4. Close the Battery / Memory Card Cover.
Getting Ready
Inserting or Removing an SD Card
2
5
Getting Started
Error Message TableError Message Table
R9000094
1. R9000094 2. Pantone 282C 3. 80P
Working Mode
Focus Range
Flash Modes
Digital Zoom
Thumbnails
Self-timer
Movie Clip
Memory Card Inside
Battery Status
Image Size (Resolution)
Image Quality
White Balance
Exposure
Protected Image
Print (DPOF)
Voice Memo
Darkness Warning
Photo Frame
Processing
AUTO
+
+
-
0
X1
X4
1 2 3
11
44
22 33
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
KONICA KD-30M User manual
-
Tekxon Technology TX6000 User manual
-
Samsung DIGIMAX V50 User manual
-
Samsung L73S User manual
-
Samsung KENOX X70 User manual
-
-
-
Samsung VLUU NV15 User manual
-
-
Samsung SAMSUNG L700 User manual
