Hobart 705S is a multipurpose kitchen appliance that can both tenderize and slice various food products. It features 86 blades set on two rollers, providing a total of 1,118 cutting surfaces. This design allows for simultaneous cutting and tenderizing from both sides, resulting in uniform and tender results. The Hobart 705S is also equipped with stainless steel knives that can be adjusted to produce slices in two different thicknesses: 1/2 inch and 3/8 inch.
Hobart 705S is a multipurpose kitchen appliance that can both tenderize and slice various food products. It features 86 blades set on two rollers, providing a total of 1,118 cutting surfaces. This design allows for simultaneous cutting and tenderizing from both sides, resulting in uniform and tender results. The Hobart 705S is also equipped with stainless steel knives that can be adjusted to produce slices in two different thicknesses: 1/2 inch and 3/8 inch.
Model 705
Tenderizer/Stir Fry Cutter
❏ 705 Tenderizer
❏ 705-S Stir Fry Cutter
Item #
Standard Features
➤ ❑ Model 705 Tenderizer consists of 86 blades
on two rollers providing 1,118 cutting edges;
design cuts and knits the meat from both sides
simultaneously for smooth meat flow and a
uniform tenderizing pattern that tightly seals in
juices when cooked
➤ ❑ Model 705-S Stir Fry Cutter produces clean,
uniform strips of meat to a pre-set thickness of
either 1/2” (13 mm) or 3/8” (10 mm) thick; up to
14 stainless steel knives cleanly cut up to 13 strips
at a time
➤ 1-speed, 1/2 HP, totally enclosed and permanently
lubricated knife motor
➤ Furnished in 115/60/1, 7.6 amp, AC, ETL listed
➤ Finish is corrosion resistant and sanitary
burnished aluminum with clear Lexan safety
cover; unit disassembles quickly without tools
for easy cleaning
➤ ❑ Model 705 Tenderizer Basket assembly
includes blades, rollers and strippers of heavy-
duty stainless steel, with nylon spacers
➤ ❑ Model 705-S Stir Fry Cutter Basket assembly
includes blades, spacers, traction drive and
stripper of heavy-duty stainless steel
➤ The unit handles product up to 1-1/4”
(32 mm) thick by 7-7/8” (200 mm) wide
➤ Direct gear drive transmission, resiliently coupled
and enclosed with permanently lubricated gear box
➤ Safety cover electromagnetic interlock prevents
the tenderizer from running when cover is raised
➤ On/off, rocker type switch
➤ Attached 6-foot, flexible, 3-wire cord and plug for
grounded receptacle
➤ Model SFC Stir Fry Cutter Basket Assembly
converts 705 and earlier model Berkel tenderizers
to optional stir fry cutters
Accessories
❑ SFC Stir Fry Cutter Basket – 3/8” (10 mm)
❑ SFC Stir Fry Cutter Basket – 1/2” (13 mm)
❑ Leg Runners
Tenderizer/Stir Fry Cutter Model 705
Berkel Company • 4406 Technology Drive • South Bend, IN 46628-9700
574-232-8222 • 800-348-0251 • FAX 888-888-2838 • www.berkel.com
Form #SPC17-0902N
Safety and Convenience Features
Berkel Model 705 tenderizer produces a better
product. The unit provides a smooth meat flow
and uniform tenderizing pattern that cuts and knits
the meat from both sides simultaneously. This
thorough tenderizing process produces an
appetizing product that seals in the juices when
cooked. The clear Lexan safety cover facilitates the
feed process while keeping the operator’s hands
at a safe distance from the tenderizing blades. An
electromagnetic interlock cuts power to the unit
when the cover is raised.
Model 705-S Stir Fry Cutter produces clean, uniform
3/8” or 1/2” thick strips of meat. The unit’s stainless
steel knives with positive product drive produce
up to 13 consistently cut strips at a time. Both
models are easy to clean and disassemble quickly
without tools.
Approved By:
Date
Model 705
C
705 Tenderizer Technical Manual Page 3 of 26
Form #SPC17-0902N Made in the U.S.A. © 2002 Berkel Company Litho in U.S.A.
Berkel Company • 4406 Technology Drive • South Bend, IN 46628-9700
574-232-8222 • 800-348-0251 • FAX 888-888-2838 • www.berkel.com
Tenderizer/Stir Fry Cutter Model 705
Model 705
Tenderizer/Stir Fry Cutter
Specifications
Models: ❑ Model 705 Tenderizer consists of 86
blades on two rollers providing 1,118 cutting
edges; design cuts and knits the meat from both
sides simultaneously for smooth meat flow and a
uniform tenderizing pattern that tightly seals in
juices when cooked.
❑ Model 705-S Stir Fry Cutter produces clean,
uniform strips of meat to a pre-set thickness of
1/2” (13 mm) or 3/8” (10 mm) thick. Stainless steel
knives cleanly cut up to 13 strips at a time.
❑ Model SFC Stir Fry Cutter Basket Assembly
converts 705 and earlier model Berkel tenderizers
to optional stir fry cutters.
Motor: 1-speed, 1/2 HP, totally enclosed, perma-
nently lubricated ball bearings, thermally protected.
Electrical: Furnished in 115/60/1, 7.6 amp, AC,
ETL listed.
Finish/construction: Finish is corrosion resistant
and sanitary burnished aluminum with clear Lexan
safety cover. The unit disassembles quickly
without tools for easy cleaning.
Transmission: Direct gear drive transmission,
resiliently coupled and enclosed with permanently
lubricated gearbox.
Cutting Capacity: Model 705 and 705-S handle
product up to 1-1/4” (32 mm) thick by 7-7/8”
(200 mm) wide.
Tenderizer Group: Model 705 Tenderizer Basket
assembly includes blades, rollers and strippers of
heavy-duty stainless steel with nylon spacers.
Stir Fry Cutter Group: Model 705-S Stir Fry Cutter
Basket assembly includes blades, spacers, traction
drive and stripper of heavy-duty stainless steel.
Safety Cover Interlock: Electromagnetic interlock
deactivates the tenderizer/stir fry cutter when the
safety cover is raised so the unit will not run.
On/Off Switch: Highly reliable, on/off, manual,
rocker type switch.
Cord and Plug: Attached 6-foot, flexible, 3-wire cord
and plug for grounded receptacle.
Warranty: All parts, service and travel coverage for
one year, excluding wear items.
As we continually strive to improve our products, specifications
are necessarily subject to change without notice.
Model No. Product 705-S Slice Output Product Dimensions
Capacity Thickness Speed Width A Depth B Height C
705 1-1/4” (32 mm) thick 1/2”, 3/8” 120 RPM 16-1/8” 13-5/8” 16-1/4”
7-7/8” (200 mm) wide (13, 10 mm) (410 mm) (346 mm) (413 mm)
Motor Electrical Weight Box Dimensions
Width Depth Height
1-speed 115/60/1 Net 62 lbs. (28 kg) 20-1/2” 19” 19”
1/2 HP Ship 70 lbs. (32 kg) (521 mm) (483 mm) (483 mm)
A
C
B
10”
(254 mm)
15-1/2”
(394 mm)
705 Tenderizer Technical Manual Page 4 of 26
12 • 705 & 705S OWNER/OPERATOR MANUAL
OWNER/OPERATOR
MANUAL
IMPORTANT NOTICE
This manual contains Important Safety
Instructions which must be strictly
followed when using this equipment.
NOTICIA IMPORTANTE
Este manual contiene importantes instrucciones
de seguridad que deben ser seguidas el pie de la
letra cuando utilice esta maquina.
MODELS
705 & 705S
TENDERIZER
705 Tenderizer Technical Manual Page 5 of 26
705 & 705S OWNER/OPERATOR MANUAL • 11
BEFORE USING THIS EQUIPMENT
Berkel’s tenderizers are designed to tenderize/slice meat and other food prod-
ucts safely and efficiently. However, unless the operator is properly trained
and supervised, there is the possibility of a serious injury. It is the responsibil-
ity of the owner to ensure that this tenderizer is used properly and safely,
strictly following the instructions contained in this manual and any require-
ments of local law.
No one should use or service this tenderizer without proper training and su-
pervision. All operators should be thoroughly familiar with the procedures
contained in this manual. Even so, Berkel cannot anticipate every circum-
stance or environment in which its tenderizers will be used. You, the owner
and operator, must remain alert to the hazards posed by the function of a ten-
derizer—particularly the sharp rotating blades/knives. No one under 18 years
of age should operate this equipment. If you are uncertain about a particular
task, ask your supervisor.
This manual contains a number of safe practices in the General Safety Instruc-
tion Section. Additional warnings are placed throughout this manual. WARN-
INGS RELATED TO YOUR PERSONAL SAFETY ARE INDICATED
BY:
WARNING
If any warning label, wall chart or manual becomes misplaced, damaged or
illegible, please contact your nearest distributor or Berkel directly, for a free
replacement.
Remember, however, THIS MANUAL OR THE WARNING LABELS DO
NOT REPLACE THE NEED TO BE ALERT AND TO USE YOUR
COMMON SENSE WHEN USING THIS TENDERIZER.
705 Tenderizer Technical Manual Page 6 of 26
705 & 705S OWNER/OPERATOR MANUAL • 1
TABLE OF C ONTENTS
Page
General Safety Instructions.................................................................................................................. 2-3
Equipment Identification ..................................................................................................................... 4
Intended Uses ...................................................................................................................................... 5
Safety Characteristics .......................................................................................................................... 5
Unpacking and Installation.................................................................................................................. 5
Cleaning and Maintenance .................................................................................................................. 6
Reassembly.......................................................................................................................................... 7
Overloading ......................................................................................................................................... 7
Models ................................................................................................................................................. 8
Troubleshooting................................................................................................................................... 8
Repair Parts/Repair Service................................................................................................................. 9
Specifications....................................................................................................................................... 9
Warranty ............................................................................................................................................ 10
Berkel Company • World’s Leading Manufacturer of Slicers and Food Processing Equipment
BERKEL COMPANY
4406 Technology Drive · South Bend, Indiana 46628-9700
574/232-8222 · Fax 574/232-8116
(800)348-0251
Form No. 4297R0202 Printed in USA Berkel Company Part No. 3175-00598
705 Tenderizer Technical Manual Page 7 of 26
2 • 705 & 705S OWNER/OPERATOR MANUAL
PELIGRO
CUCHILLA FILOSA
para evitar serios accidentes a su
persona siga las instrucciones de este
manual y
1. NUNCA utlice esta mçquina sin previa instrucciùn y autorizaciùn de su
supervisor.
2. LA MáQUINA DEBE apoyarse sobre un nivel solido y plano.
3. LOS PROTECTORES deben colocarse ANTES de enchufar y operar la
máquina.
4. SIEMPRE utilice el enchufe original proveido por el fabricante.
5. SIEMPRE utilice el utensillo para empujar la
comida - nunca su mano.
6. NUNCA TOQUE LA CUCHILLA CON
LA MANO.
7. MANTENGA manos, brazos, cabello y
ropa suelta LEJOS de toda parte en movimiento
de la máquina.
8. EN CASO DE QUE LA MáQUINA SE TRABE,
apague y desconecte ANTES de sacar lo que la obstruye.
9. APAGUE Y DESCONECTE LA MáQUINA antes de limpiar,
sanitizar, o arreglar.
10. UTILIZE UNICAMENTE los repuestos provistos por el fabricante.
11. EN CASO de que los membretes de ‘PELIGRO’ se desprendan
de la máquina o sean illegibles, llame al fabricante o a su
representante de service Berkel para que lo reemplace sin cargo.
705 Tenderizer Technical Manual Page 8 of 26
705 & 705S OWNER/OPERATOR MANUAL • 3
WARNING
SHARP KNIFE BLADE
to avoid serious personal injury
follow all the instructions in this manual
and
1. NEVER touch this machine without training and authorization by your
supervisor.
2. MACHINE MUST BE on solid level support.
3. GUARDS MUST BE in place before plugging in and turning on machine.
4. ALWAYS use three pronged plug provided.
5. ALWAYS use food pusher not your hand.
6. NEVER TOUCH ROTATING KNIFE.
7. KEEP hands, arms, hair and loose clothing
clear of all moving parts.
8. SHOULD MACHINE JAM, turn off and unplug
before removing obstruction.
9. TURN OFF AND UNPLUG machine from power source before cleaning,
sanitizing or servicing.
11. USE ONLY the attachments provided by the manufacturer.
12. SHOULD any warning label on a machine come off or become unreadable
contact the manufacturer or your designated Berkel service location for a
free replacement.
705 Tenderizer Technical Manual Page 9 of 26
4 • 705 & 705S OWNER/OPERATOR MANUAL
EQUIPMENT IDENTIFICATION
Safety Cover
ON/OFF Switch
Blade and
Frame Assembly
Locking
Lever
Clutch Gear
705 Tenderizer Technical Manual Page 10 of 26
705 & 705S OWNER/OPERATOR MANUAL • 5
INTENDED USES
The 705 and 705S tenderizers are designed for processing the following types of food products:
• Beef
• Poultry
• Pork
• Vegetables
The following items are not suitable to be processed on the 705 and 705S tenderizers:
• Products on/with bones
• Frozen products
• Non-food products
SAFETY CHARACTERISTICS
• The cover is equipped with a safety interlock that will not allow the tenderizer to be turned on
unless the cover is in the down position.
• The tenderizer does not cause noise pollution; the noise level is below 70dB.
• Make sure the line voltage matches the tenderizer before the main is connected; voltage is listed
on the serial plate.
WARNING
TO PREVENT SERIOUS PERSONAL INJURY, DO NOT MODIFY
OR REMOVE THE SAFETY PROVISIONS IN ANY WAY.
UNPACKING & INSTALLATION
1. Unpack the Blade and Frame assembly from its carton.
2. Raise the cover to its top position.
3. Lift the blade and frame assembly by gripping the knife frame guides in the center, with drive
clutches to your left. Lower the blade and frame assembly into the front of the machine until it
rests firmly on the four (4) support pins. Slide assembly to the left, which engages the clutches.
4. Lower the safety neck forward into the operating position.
705 Tenderizer Technical Manual Page 11 of 26
6 • 705 & 705S OWNER/OPERATOR MANUAL
WARNING
FOR PERSONAL SAFETY, THIS TENDERIZER WILL NOT OPERATE WITHOUT THE
SAFETY NECK IN PLACE. NEVER RAISE OR LOWER THE SAFETY NECK WITH THE
MACHINE TURNED ON, BOTH FOR PERSONAL PROTECTION AND MACHINE PROTEC-
TION. ALWAYS TURN MACHINE OFF WHEN NOT IN USE. ONLY RUN MACHINE BY
USING THE ON/OFF SWITCH, NEVER BY RAISING OR LOWERING THE COVER.
5. Uncoil power cord and plug into a grounded, approved outlet. (Specifications for this machine
are found on the serial plate located on the left-hand leg.)
6. Push ON/OFF rocker switch to ON. If cutting knives do not rotate, turn machine OFF and
unplug power cord. Lack of rotation indicates that the clutches are not engaging. Raise the
safety shield and slide the assembly to the left. Lower safety shield, plug in power cord and turn
ON.
THE TENDERIZER IS NOW READY TO USE.
CLEANING & MAINTENANCE
1. Turn off machine and unplug power cord.
2. Remove safety cover by raising cover and pulling the spring loaded pivot knob to your left. Lift
out.
3. Hand wash and rinse the safety cover and set it aside to air dry. Sanitize with an approved
sanitizer before reassembling. Only use an approved sanitizing solution, Berkel part number
4975-00400.
WARNING
TO PREVENT CUTS, ALWAYS WEAR APPROVED
SAFETY GLOVE WHEN HANDLING STIR-FRY BLADES.
4. Grip the blade and frame assembly at the center of the frame sides. Move to the right to disen-
gage from the clutch. Lift out and set it on a working surface.
5. Push down the locking plate on the right side of the assembly.
WARNING
KNIVES ARE SHARP. ONLY HANDLE BLADES AND KNIVES
BY THE SHAFT ENDS TO AVOID CUTTING HANDS.
6. Grasp both ends of front blade assembly and lift out of frame. Set it back out of the way. Do the
same with the rear blade assembly.
7. Lift out front stripper plate.
8. Remove back stripper plate by rotating up and out.
NOTE: There is no back stripper plate on a stir-fry assembly.
705 Tenderizer Technical Manual Page 12 of 26
705 & 705S OWNER/OPERATOR MANUAL • 7
9. All removable parts can be soaked and scrubbed using a bristled brush and good quality deter-
gent approved for food processing equipment.
10. Rinse thoroughly and set aside to air dry while you are washing the machine case.
11. Sanitize all blade and frame assembly parts and tenderizer unit.
REASSEMBLY
1. Replace stripper plates with solid flanges to the outside of the assembly, teeth to the center and
pointing up. (Front and back stripper plates for the tenderizer group are interchangeable.)
2. Inspect blades (especially if blades have been jammed by bone segments or have been mis-
handled). If any of the blades in the assembly are bent, replace with a new blade immediately,
otherwise you could damage the blade assembly.
3. With lock plate down, grasp blades by shaft ends and replace. Match color end plugs on blade to
matching colored dots on frame: Red for rear blade, white for front blade.
NOTE: Blade shafts are not interchangeable.
4. Raise locking plate up to lock blade assembly in place.
5. Replace the blade and frame assembly as previously shown and slide to the left to engage with
the clutches.
6. Replace safety cover by retracting pivot pin and latching into the housing. Lower safety neck
into closed position.
7. Plug power cord into wall receptacle.
THE TENDERIZER IS NOW READY TO USE.
OVERLOADING
The machine may jam from overloading or by a piece of bone accidentally being fed into the blades.
If this should happen:
1. Turn off machine immediately.
2. Unplug power cord.
3. Disassemble frame and blade assembly. Inspect for bent blades.
4. Remove obstructions, clean, inspect and reassemble.
705 Tenderizer Technical Manual Page 13 of 26
8 • 705 & 705S OWNER/OPERATOR MANUAL
MODELS
Model 705: Tenderizer (includes tenderizer blade and frame assembly).
Model 705S: Stir-Fry Cutter (includes stir-fry cutter blade and frame assembly).
Model SFC: Stir-Fry Blade and Frame Assembly (to convert 705 and earlier model Berkel to
optional stir-fry cutter use).
TROUBLESHOOTING
Should your tenderizer fail to function properly, here are a few things you can check before calling a
Designated Berkel Service Location for service.
Product not tenderizing or slicing properly:
1. Are the knives/blades dull or bent? If so, contact your nearest Designated Berkel Service Loca-
tion for replacement.
2. Does the product size exceed the capacity of the tenderizer? Too large a product may rub against
the cover or frame assembly causing interference to normal slicing or tenderizing.
3. Are the blade assemblies securely mated to the driving gears? If not, make sure that the basket
assembly is pushed all the way to the left.
Electrical failure:
1. Is tenderizer fully plugged into a properly grounded 120 volt AC outlet?
2. Inspect power cord. Has it been damaged, cutting off electrical flow? If so, call your Designated
Berkel Service Location to replace the power cord.
3. Is ON/OFF switch in the ON position?
4. Are you getting electricity from the wall outlet? Check by plugging in another piece of equip-
ment with the same electrical requirements. Also, check circuit breaker or fuse
5. Is the Lexan cover completely down?
6. If you are getting electrical power and your tenderizer is still not operating, contact your Desig-
nated Berkel Service Location.
If correction of any of the above conditions does not result in a functional tenderizer, call your
Designated Berkel Service Location.
705 Tenderizer Technical Manual Page 14 of 26
705 & 705S OWNER/OPERATOR MANUAL • 9
REPAIR PARTS/REPAIR SERVICE
Please contact your Designated Berkel Service Location for any repair parts and/or repair service
required on your Berkel tenderizer. Additional information may be obtained from:
Service Support Center
Berkel Company
4406 Technology Drive
South Bend, Indiana 46628-9700
574/232-8222 · Fax 574/232-8116
(800) 348-0251
SPECIFICATIONS
Motor: 1/2hp, 115 volt, 60 cycle single phase, 7.5 amps, thermally protected
Transmission: Direct gear drive, resiliently coupled, enclosed in a permanently lubricated
gearbox.
Output Speed: 120 RPM
Product Capacity: 1
1
/
4
” (32mm) x 7
7
/
8
” (200mm)
Dimensions:
Width: 16” (406mm)
Width: 16” (406mm) (foot to foot)
Depth: 13-5/8” (346mm)
Depth: 10-5/8” (270mm) (foot to foot)
Height: 16” (406mm)
Weight:
Net: 60 lbs. (27.3 kg)
Shipping: 72 lbs. (32.7 kg)
Stir-Fry Sizes: 3/8” (9.5 mm) part number 4975-00324
1/2” (13 mm) part number 4975-00324
11/16” (17.5 mm) part number 4975-00324
7/8” (22 mm)
part number 4975-00324
Protective Glove: Small, part number 4975-00319
Medium, part number 4975-00320
Large, part number 4975-00321
Cleaning Brush: Part number 4975-00320
705 Tenderizer Technical Manual Page 15 of 26
10 • 705 & 705S OWNER/OPERATOR MANUAL
WARRANTY
Berkel Company (“Berkel”) warrants to the Buyer of new equipment that said equipment, when
installed in accordance with our instructions and subjected to normal use, is free from defects
in material or workmanship for a period of one (1) year from the date of sale.
1
BERKEL SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MER-
CHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE.
Berkel’s obligation and liability under this warranty is expressly limited to repairing or
replacing equipment that proves to be defective in material or workmanship within the appli-
cable warranty period. Berkel or a Designated Berkel Service Location will perform all
repairs pursuant to this warranty. Berkel expressly excludes responsibility for incidental or
consequential damages to buyer or any third party, including, without limitation, damages
arising from personal injuries, lost profits, loss of business opportunity, loss of property,
economic losses, or statutory or exemplary damages, whether in negligence, warranty, strict
liability or otherwise.
This warranty does not apply to: periodic maintenance of equipment including but not lim-
ited to lubrication, replacement of worn blades, knives, stones, knobs, accessories, and mis-
cellaneous expendable supply items, and other adjustments required due to installation set-up
or normal wear.
These warranties are given only to the first purchaser from a Berkel Authorized Channel of
Distribution. No warranty is given to subsequent transferees.
The foregoing warranty provisions are a complete and exclusive statement of the warranty
between the buyer and seller. Berkel neither assumes nor authorizes any persons to assume
any other obligation or liability connection with said equipment.
1
Model 180 slicers carry a 90-day warranty.
705 Tenderizer Technical Manual Page 16 of 26
705 Tenderizer Technical Manual Page 17 of 26
BK46724
NOTICIA IMPORTANTE
Este manual contieneimportantes instrucciones
de seguridad que deben ser seguidas el pie de la
letra cuando utilice esta maquina.
Parts Listing
Model 705
IMPORTANT NOTICE
This manual contains important safety
instructions which must be strictly
followed when using this equipment.
705 Tenderizer Technical Manual Page 18 of 26
2
705 Tenderizer Technical Manual Page 19 of 26
3
(*) For Blade Options, See Page 5
705 Tenderizer Technical Manual Page 20 of 26
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Hobart 705S Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Hobart 705S is a multipurpose kitchen appliance that can both tenderize and slice various food products. It features 86 blades set on two rollers, providing a total of 1,118 cutting surfaces. This design allows for simultaneous cutting and tenderizing from both sides, resulting in uniform and tender results. The Hobart 705S is also equipped with stainless steel knives that can be adjusted to produce slices in two different thicknesses: 1/2 inch and 3/8 inch.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
