Definitive Technology DI 6.5STR User manual

Brand: Definitive Technology

Model: DI 6.5STR

Category: Soundbar speakers

Type: User manual

Unpacking Your Disappearing In-Wall Speakers

Please Inspect For Shipping Damage

Each loudspeaker leaves our plant in perfect condition. Any visible or concealed

damage most likely occur

ed in handling after it left our plant and should be r

epor

ted

at once to your Definitive dealer or the deliver

y company that deliver

ed your loud

speaker. Please unpack your system carefully. Save all cartons and packing materials

in case you move or need to ship your system. Recor

d the serial number found on

the back of the speakers, and on the car

ton, in this manual and save it for futur

reference should your speaker need service. For your best protection, register your

Di Series pr

oducts on-line at

http://r

egistration.definitivetech.com.

Definitive Technology

Di SERIES

OWNER’S MANUAL

Models: 3.5R, 4.5R, 5.5R, 6.5R, 8R, 6.5STR, 5.5S and 6.5S

Thank You

Thank you for choosing the Definitive Technology Disappearing In-Wall loud

speaker. The Di Series products offer extraordinary sound quality from speakers that

are barely visible when installed in a wall or ceiling. Our engineers spent many

years developing this pr

oduct. In order to ensure that you experience the finest per

formance possible, we encourage you to take a moment to fully read this owner’s

manual and familiarize yourself with the proper installation and set-up procedures

for your Di Series speaker

Definitive Technology

Di 5.5S

Di 6.5R

Di 6.5S

Di 6.5STR Di 8R

Di Series

Di 3.5R

Di 4.5R Di 5.5R

Di SERIES

OWNER’S MANUAL

Painting Di Series Speakers

Your Di Series speakers may be painted to match the color of the wall

or ceiling in which they are installed. Failure to follow the following

painting instructions may result in seriously degraded sound quality.

It is your responsibility to make sure your painting contractor sees and

follows these instructions.

1. DO NOT PAINT THE GRILLE WITH A BRUSH OR ROLLER —

they will clog the fine mesh of the grille and cloth scrim and result

in poor sound quality.

2. Remove the grille from the speaker and place it on a drop cloth,

newspaper or plastic sheet.

3. The grille MUST be spray painted with one of the following:

• Spray paint that closely matches the desired finish/color

• A custom spray bomb, color matched to your paint finish

• Indoor latex paint using a spray gun (paint must be diluted

to the paint manufacturer’s specifications)

4. Removing the backing cloth (scrim) is not required.

5. Paint should be applied in a series of thin coats sprayed at

approximately 60 degrees from the grille surface, allowing each

coat to fully cure before applying additional coats.

6. To ensure that the paint distribution is evenly applied, each coat

should be applied from at least 4 different directions to the grille.

(N, S, E & W) This will ensure an even coverage on the grille.

7. Once the grille has been painted and the paint has fully cured, you

may use a brush, or small roller to touch-up the outer edge of the

grille frame — being VERY careful not to get any additional paint

on the grille mesh surface.

Optional Fire-Rated Enclosures

Definitive Di Series speakers have been designed to meet UL 1480 and

2043 standar

ds when used with the appr

opriate optional Definitive

fire-rated enclosures. All plastic parts used in the speakers are V0 flame

rated as per UL 94.

While these enclosures are necessary in most countries for commercial

and multi-family dwelling installations, r

esidential customers may want

to use them for added safety and/or to r

educe the sound fr

om “leaking”

into adjacent rooms.

Placement Options

Definitive T

echnology Di Series Loudspeakers give you nearly endless

placement options. But remember that placement choice for your in-wall

speakers bears careful consideration, as installation requires that you cut a

hole in your wall or ceiling! Fill a room with sound by installing in-wall

speakers in nearly any wall or ceiling location although it is best to keep

the speakers at least 2 feet (60 cm) from side walls [

Figure 1]. When using

Di Series models in home theater applications follow the guidelines

[illustrated in

Figures 2, 3 and 4]. Definitive Di Series In-Wall Loudspeakers

have aimable tweeters that allow you to focus their sound towar

d or

away from your listening ar

ea depending on the application.

Figure 1

Figure 2

Figure 3

Figure 4

Di SERIES

OWNER’S MANUAL

Aiming the Tweeter

A tweeter aimed toward your listening position improves imaging and

detail. To aim the tweeter, first install the speaker in the desired location.

Rotate the tweeter so that the arrow on the tweeter faceplate is pointing

in the direction you wish to aim the tweeter [Figure 5] then gently push

the tweeter in that direction [Figure 6]. When using Di Series In-Wall

Loudspeakers as front/main home theater speakers or as stereo speakers

in a distributed audio system aim the tweeter toward the main listening

position. For rear/surround speakers installed in walls or ceilings, aim

the tweeter toward the nearest reflecting surface (an adjacent wall or

ceiling) for a more diffuse sound field (if you so desir

e; for mor

e dir

ect

sound, aim the tweeters at your listening position).

nvironmental EQ

(not included on Di 3.5R and Di 4.5R models)

If your listening room is very reflective, with smooth sheetrock walls,

hardwood floors, and non-cushioned furniture, the sound will be overly

“bright” and unnatural. Engaging the Environmental EQ feature

[Figure 7] (by selecting the “–” setting) compensates for the effect of

overly loud treble. If your room is has a lot of absorbing surfaces such as

over-stuffed furniture, heavy drapes and rugs such that the speakers

sound “dull,” engage the “+” setting to boost treble response. Leave the

switch in the center position in rooms with a balance of reflecting and

absorbing surfaces (most rooms fall into this category). Note: the Di 6.5STR

has a two position switch; the minus symbol “-” represents normal treble

output and the plus symbol “+” represents treble boost.

Installation

Installation Cautions

Installation of Disappearing Series Loudspeakers requires skills in

using tools such as a drill, screwdriver, saws and power tools. Installation

also entails running wires through walls. You should have a thorough

understanding of local building and fire codes and a familiarity with

the ar

ea behind the wall or ceiling into which you plan to install

your speakers.

When cutting holes in and running wires through walls/ceilings you run

the risk of cutting electrical wires or water pipes thereby causing safety

hazards and property damage. If you are in any doubt that you possess

the necessary skills or tools, contact your Definitive Technology dealer,

general contractor or a professional installer.

Required Tools

• Pencil for marking the location of installation.

•

Bubble level (for Di 5.5S and Di 6.5S models only)

• Keyhole saw, utility knife or material- appropriate incising

implement for cutting drywall or other wall material.

• Phillips head screwdriver.

•

Power drill with appropriate bit (optional, for starting wall cut).

Installation Procedure

• You must first install speaker wires that meet appropriate building and

fire codes before installing the speakers. Use at least 18 gauge wire or

heavier to ensur

e optimum sound quality

Figure 7

Figure 5

Point tweeter in desired

direction by turning the

tweeter assembly.

Figure 6a

Push gently in

direction of arrow

to set angle.

Figure 6b

• Once you have cut the hole, pull the speaker wire

out of the hole and connect the speaker. Strip

inch (12 mm) of insulation from each of the two

conductors of the wire to expose the bare metal

and twist each of the conductors into a single

unfrayed strand. Note that one of the terminals

on the rear of each speaker is marked red (+) and

the other black (-). Make certain that you connect

the wire from the red terminal (+) of your amplifi-

er or receiver to the red terminal (+) on your

speaker and the wire from the black terminal (-)

of your amplifier or receiver to the black terminal

(-) on your speaker

. Most wire has some indicator

(such as color

-coding, ribbing or writing) on one

of the two conductors to help you maintain

consistency [

Figure 11a]. In the case of the Di

6.5STR single speaker ster

eo model, both left

and right channel speaker wires are connected

to the speaker [Figur

e 11b

• Push down on the top of the terminal to reveal

the wir

e hole in the side of the terminal post and

insert the wire into the hole [

Figure 12]. Release

the pr

essur

e on the terminal to secure the wire.

• Loosen the rotating lock arms by turning the lock

arm screws on the front of the speaker counter

clockwise

⁄2 to 1 turn, just enough to allow the lock

arm to move freely. [Figure 13]. Make sure that the

otating lock ar

ms ar

e flipped inwar

ds [

Figur

e 14

]

so that your speaker fits into your cutout.

• Make sure the material into which you plan to mount the speakers

(plaster, drywall, paneling, stone, etc.) can support the weight of

the speakers (see specification page for the weight of your model).

• Make sure the locations you select do not conceal studs, electrical

wiring or plumbing. Prior to installation, hold the speaker with

grille on in your chosen

location to make sure it safely

clears obstacles such as studs,

corners, beams, lighting

fixtures and door/window

rames. Your cutout must

be at least 2" (50 mm) from

adjoining walls or ceiling,

internal studs or plumbing.

• Using the supplied template,

trace the installation location

with a pencil. You can do

this by holding the template

in your pr

eferred location

and tracing around it. In the

case of the rectangular

models (Di 5.5S and Di 6.5S)

use a bubble level to square

and level the template.

[

Figures 8 & 9]

• Carefully cut the hole

with the appropriate cutting

tool for your wall or ceiling

material. Start the hole by

drilling a hole on the inside

of the tracing (with the drill

bit just inside the line). Use

this hole to insert the saw

or knife and begin cutting

[

Figure 10]. The holes for the

Di 3.5R and Di4.5R must be

cut very precisely as their

flanges ar

e only

" (9.5 mm)

wide. W

e r

ecommend using

hole saws to cut the holes

for these models — 3

" for

the Di 3.5R and a 4

" for

the Di 4.5R.

Definitive Technology

AMP L IF IE R OR

REC E IV ER

igure 8

Figure 9

Figure

11b

Figur

e 10

Figure 12

Figure 11a

Left channel wires

Right channel wires

Template

–

Definitive Technology

• Place the speaker carefully into the cutout. If you have a level, use it

to help you correctly align rectangular speaker models. Tighten the

lock arm screws with a screwdriver [Figure 15]. This will rotate the

lock arms [Figure 16] and secure the speaker to the wall/ceiling.

Do not over-tighten the lock arm screws. If you are using a powered

screwdriver or drill set the torque to a value of 7 in. – lb. (8dN – m)

• Install the grille on the speaker frame. Powerful magnets hold the

grille in place.

Lock arms

tucked

in prior

to installing

speaker

in wall.

Figure 14

Figure 13

Lock arm

screws.

Turn counter

clockwise

to loosen.

Figur

e 16

Figur

e 15

Lock ar

scr

ews.

n clock

wise to

tighten lock

ms and

secur

e speaker

to sur

face.

Di SERIES

OWNER’S MANUAL

SAFETY FIRST

When installing your Di Series In-Wall Loudspeakers, be aware of the

weight of your particular model (see specification page for the weight

of your model) and the sturdiness of the material into which you are

installing the speaker. Also be aware of any concealed studs, electrical

wiring or plumbing in the wall or ceiling into which you are installing

the speakers. If you are not sure of a safe way to install these speakers,

consult a professional installer, your authorized Definitive Technology

dealer, or a building contractor.

Technical Assistance

It is our pleasure to offer assistance if you have any questions regarding

your Definitive loudspeakers. Please contact your nearest Definitive

Technology dealer or call us directly at (800) 228-7148 (US & Canada),

01 (410) 363-7148 (all other countries) or e-mail

[email protected].

Service

Service work on your Definitive loudspeakers will normally be performed

by your local Definitive Technology dealer. If your dealer is unable or

unwilling to perform service contact us for alternative options. Please

note that the address given in this manual is the address of our offices

only. Under no circumstances should loudspeakers be shipped

to our offices or returned without contacting us first and

obtaining return authorization.

Definitive Technology Offices

11433 Cr

onridge Drive

Owings Mills, Maryland 21117

Phone: (800) 228-7148 (US & Canada),

01 (410) 363-7148 (all other countries)

ARNING: LISTEN CAREFULL

Definitive T

echnology loudspeakers and subwoofers are capable of

playing at extremely high volume levels, which could cause serious or

per

manent hearing damage. Definitive T

echnology accepts no liability

for hearing loss, bodily injury or property damage resulting from the

misuse of its products.

You should limit prolonged exposur

e to volumes that exceed

85 decibels (dB).

For more about safe volume levels refer to the Occupational

Health and Safety Administration (OSHA) guidelines at:

www.osha.gov/dts/osta/otm/noise/standar

ds_mor

e.html.

NOTES

EQAT020209

Specifications

Di 3.5R Di 4.5R Di 5.5R Di 6.5R Di 6.5STR Di 8R Di 5.5S Di 6.5S

rille Diameter 4-9/16"

(

11.6 cm)

-3/8"

(

13.55 cm)

-3/8"

(

18.62 cm)

-5/16"

(

21.04 cm)

-5/16"

(

21.04 cm)

-3/4" (

4.76 cm)

—

Grille Length —— — — — —7-3/8" (18.61 cm) 8-5/16" (21.01 cm)

Grille Width —— — — — —7-3/8" (18.61 cm) 8-5/16" (21.01 cm)

Cutout Diameter 3-3/4" (9.55 cm) 4-1/2" (11.5 cm) 6-5/16" (16 cm) 7-1/4" (18.4 cm) 7-1/4" (18.4 cm) 8-3/4" (22.2 cm) ——

Cutout Width —— — — — —6-5/16" (16 cm) 7-1/4" (18.4 cm)

Cutout Length —— — — — —6-5/16" (16 cm) 7-1/4" (18.4 cm)

Total Depth * 3" (7.55 cm) 3-3/8" (8.64 cm) 3-5/8" (9.04 cm) 3-5/8" (9.07cm) 3-5/8" (9.07 cm) 3-7/8" (9.77 cm) 3-5/8" (9.04 cm) 3-7/8" (9.70 cm)

Mounting Depth In-Wall ** 2-1/2" (6.3 cm) 2-7/8" (7.4 cm) 3-1/16" (7.8 cm) 3-1/16" (7.8 cm) 3-1/16" (7.8 cm) 3-3/8" (8.5 cm) 3-1/16" (7.8 cm) 3-1/16" (7.8 cm)

Woofer 3-1/2" (8.9 cm) 4-1/2" (11.4 cm) 5-1/4" (13.3 cm) 6-1/2" (16.5 cm) 6-1/2" (16.5 cm) 8" (20 cm) 5-1/4" (13.3 cm) 6-1/2" (16.5 cm)

Tweeter 3/4" (20 mm) 3/4" (20 mm) 1" (25 mm) 1" (25 mm) 2 @ 3/4" (20 mm) 1" (25 mm) 1" (25 mm) 1" (25 mm)

Product Weight 1.9 lb. (0.85 kg) 2.6 lb. (1.16 kg) 3.7 lb. (1.67 kg) 3.8 lb. (1.73 kg) 4.4 lb. (2.14 kg) 4.8 lb. (2.14 kg) 3.8 lb. (1.73 kg) 4 lb. (1.79 kg)

Frequency Response 40 Hz – 30 kHz 35 Hz – 30 kHz 28 Hz – 30 kHz 26 Hz – 30 kHz 26 Hz – 30 kHz 26 Hz – 30 kHz 28 Hz – 30 kHz 26 Hz – 30 kHz

Sensitivity 87 dB 88 dB 89 dB 90 dB 90 dB 90 dB 89 dB 90 dB

Impedance All models are compatible with 4 – 8 Ohm outputs.

Min/Max Recommended Power 10/125 10/150 10/175 10/200 10/125 10/225 10/175 10/200

* From back of mounting flange to deepest part of product

** Total depth when product installed in 1/2"

(12.7mm) thick material

Di SERIES

OWNER’S MANUAL

For more information on Definitive Technology Loudspeakers and accessories,

visit www.definitivetech.com, or email [email protected].

Definitive Technology, Owings Mills, Maryland, USA. 800-228-7148

DEI Sales Co., dba Definitive Technology (herein “Definitive”) warrants to the original

retail purchaser only that this Definitive loudspeaker product (the “Product”) will be free

from defects in material and workmanship for a period of five (5) years covering the

drivers and cabinets, and three (3) years for the electronic components from the date of

the original purchase from a Definitive Authorized Dealer. If the Product is defective in

material or workmanship, Definitive or its Authorized Dealer will, at its option, repair

or replace the warranted product at no additional charge, except as set forth below. All

replaced parts and Product(s) become the property of Definitive. Product that is repaired

or replaced under this warranty will be returned to you, within a reasonable time, freight

collect. This warranty is non-transferrable and is automatically void if the original

purchaser sells or otherwise transfers the Product to an

y other par

This Warranty does not include service or parts to repair damage caused by accident,

misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use,

voltage in excess of the rated maximum of the unit, cosmetic appearance of cabinetry not

directly attributable to defects in material or workmanship. This warranty does not cover

the elimination of externall

y g

ener

ated static or noise

, or the corr

ection of antenna

problems or weak reception. This warranty does not cover labor costs or damage to the

Product caused by installation or removal of the Product. Definitive Technology makes no

arr

anty with respect to its products purchased from dealers or outlets other than

Definitive Technology Authorized Dealer.

THE WARRANTY IS AUTOMATICALLY VOID IF:

The pr

oduct has been dama

ed, alter

ed in an

y way, mishandled during transportation,

or tampered with.

2) The product is damaged due to accident, fire, flood, unreasonable use, misuse, abuse,

customer applied cleaners, failure to observe manufacturers warnings, neglect or

related events.

3) Repair or modification of the Product has not been made or authorized by Definitive

Technology.

4) The product has been improperly installed or used.

Product must be returned (insured and prepaid), together with the original dated proof of

purchase to the Authorized Dealer from whom the Product was purchased, or to the

nearest Definitive factory service center. Product must be shipped in the original shipping

container or its equivalent. Definitive is not responsible or liable for loss or damage to

Product in transit.

THIS LIMITED

WARRANTY IS THE ONLY EXPRESS WARRANTY THAT

APPLIES TO YOUR PRODUCT. DEFINITIVE NEITHER ASSUMES NOR

AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY OTHER

OBLIGATION OR LIABILITY IN CONNECTION WITH YOUR PRODUCT OR THIS

ARRANTY

ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO

EXPRESS, IMPLIED,WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED AND DISCLAIMED TO

THE MAXIMUM EXTENT

ALLO

WED BY LA

ALL IMPLIED

ARRANTIES ON

PRODUCT ARE LIMITED TO THE DURATION OF THIS EXPRESSED

WARRANTY. DEFINITIVE HAS NO LIABILITY FOR ACTS OF THIRD PARTIES.

DEFINITIVE’S LIABILITY, WHETHER BASED ON CONTRACT, TORT, STRICT

LIABILITY, OR ANY OTHER THEORY, SHALL NOT EXCEED THE PURCHASE

PRICE OF THE PRODUCT FOR WHICH A CLAIM HAS BEEN MADE. UNDER NO

CIRCUMST

ANCE

WILL DEFINITIVE BEAR ANY LIABILITY FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES. THE CONSUMER AGREES AND

CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND

DEFINITIVE SHALL BE RESOL

VED IN

CCORD

ANCE

WITH CALIFORNIA

LAWS IN SAN DIEGO COUNTY, CALIFORNIA. DEFINITIVE RESERVES THE

RIGHT TO MODIFY THIS WARRANTY STATEMENT AT ANY TIME.

Some states do not allow the exclusion or limitation of consequential or incidental

damages, or implied warranties, so the above limitations may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

LIMITED USA WARRANTY

5-YEARS FOR DRIVERS AND CABINETS, 3-YEARS FOR ELECTRONIC COMPONENTS

This product complies with the essential requirements of the EMC directive 89/336/EEC.

Definitive Technology DI 6.5STR User manual

Brand: Definitive Technology

Model: DI 6.5STR

Category: Soundbar speakers

Type: User manual

Download PDF

report

Definitive Technology DI 6.5STR User manual

Definitive Technology DI 6.5STR User manual

Related papers

Other documents