Korg TR User manual

Operation Guide

2E

ii

To ensure long, trouble-free operation,

please read this manual carefully.

Precautions

Location

Using the unit in the following locations can result

in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

Power supply

Please connect the designated AC/AC power sup-

ply to an AC outlet of the correct voltage. Do not

connect it to an AC outlet of voltage other than that

for which your unit is intended.

Interference with other electrical devices

This product contains a microcomputer. Radios and

televisions placed nearby may experience reception

interference. Operate this unit at a suitable distance

from radios and televisions.

Handling

To avoid breakage, do not apply excessive force to

the switches or controls.

Care

If the exterior becomes dirty, wipe it with a clean,

dry cloth. Do not use liquid cleaners such as ben-

zene or thinner, or cleaning compounds or ﬂamma-

ble polishes.

Keep this manual

After reading this manual, please keep it for later

reference.

Keeping foreign matter out of your equipment

• Never set any container with liquid in it near

this equipment. If liquid gets into the equipment,

it could cause a breakdown, fire, or electrical

shock.

• Be careful not to let metal objects get into the

equipment. If something does slip into the

equipment, unplug the AC/AC power supply

from the wall outlet. Then contact your nearest

Korg dealer or the store where the equipment

was purchased.

Data handling

Malfunctions due to incorrect operation may cause the

contents of memory to be lost, so we recommend that

you save important data on the external media (SD

card etc.). Please be aware that Korg will accept no

responsibility for any damages which may result from

loss of data.

* Company names, product names, and names of formats etc.

are the trademarks or registered trademarks of their respective

owners.

THE FCC REGULATION WARNING (for U.S.A.)

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Unauthorized changes or modiﬁcation to this system can void

the user’s authority to operate this equipment.

CE mark for European Harmonized Standards

CE mark which is attached to our company’s products of AC

mains operated apparatus until December 31, 1996 means it

conforms to EMC Directive (89/336/EEC) and CE mark Directive

(93/68/EEC). And, CE mark which is attached after January 1,

1997 means it conforms to EMC Directive (89/336/EEC), CE

mark Directive (93/68/EEC) and Low Voltage Directive (73/23/

EEC).

Also, CE mark which is attached to our company’s products of

Battery operated apparatus means it conforms to EMC Directive

(89/336/EEC) and CE mark Directive (93/68/EEC).

About copyright

This device is intended for use with material of

which you yourself are the copyright owner or for

which you have received permission from the

copyright owner to duplicate. If you are not the

copyright owner or have not received permission

from the copyright owner to duplicate the mate-

rial, you are in violation of copyright law, and may

be liable for damages and penalties. If you are

unsure of your rights to the material, please con-

sult a legal specialist.

iii

Thank you for purchasing the

Korg TR music workstation

.

To ensure trouble-free enjoyment, please read this manual carefully and use the instrument

as directed.

About this manual

The owner’s manuals and how to use

them

The TR come with the following owner’s manuals.

• Operation Guide

• Parameter Guide

• Voice Name List (

included in the CD-ROM)

Operation Guide

First read this manual carefully to gain a basic under-

standing of the instrument and to learn basic opera-

tion.

“Introduction”

explains the function of each part, how

to make connections, basic operation, and gives an

overview of each mode.

“Quick Start”

explains basic topics (selecting sounds,

convenient functions for performance). If you wish to

begin playing immediately, read this section ﬁrst.

“Basic Functions”

contains mode-by-mode explana-

tions of what you need to know to edit sounds, record

on the sequencer, and record samples (If the separately

sold EXB-SMPL option is installed). This section also

explains how to use the arpeggiator, effects.

“

Appendices

” contains information on troubleshoot-

ing, speciﬁcations, and various other information.

Parameter Guide

The Parameter Guide contains explanations and other

information regarding the operations of the parame-

ters and settings on the TR. The explanations are orga-

nized by mode, and page. Explanations and other

information on the effects and their parameters are also

provided for each effect.

Refer to this guide when an unfamiliar parameter

appears in the display, or when you need to know

more about a particular function.

Voice Name List

This lists the multisamples and drumsamples that are

built into the TR, and the factory preset combinations,

programs, drum kits, and user arpeggio patterns.

Refer to these lists when you wish to know more about

the preloaded sounds.

Conventions in this manual

References to the TR

The TR is available in 88-key, 76-key and 61-key mod-

els, but all three models are referred to without distinc-

tion in this manual as “the TR.” Illustrations of the

front and rear panels in this manual show the 61-key

model, but the illustrations apply equally to the 76-key

and 88-key models.

Abbreviations for the manuals OG, PG, VNL

References to the manuals included with the TR are

abbreviated as follows in this document.

OG

: Operation Guide

PG

: Parameter Guide

VNL

: Voice Name List (

included in the CD-ROM)

Switches and knobs [ ]

References to the switches, dials, and knobs on the

panel are enclosed in square brackets [ ].

Parameters in the LCD display screen “ “

Parameters displayed in the LCD screen are enclosed

in double quotation marks “ “.

Boldface type

Parameter values are printed in boldface type.

Content that is of particular importance is also printed

in boldface type.

Procedure steps

1

2

3

...

Steps in a procedure are listed as

1

2

3

...

☞

p.

■

,

☞

PG p.

■

These symbols indicate a reference page number in the

Operation Guide or in the Parameter Guide.

Symbols , ,

These symbols respectively indicate cautions, advice,

and MIDI-related explanations.

Example screen displays

The values of the parameters shown in the example

screens of this manual are only for explanatory pur-

poses, and may not necessary match the values that

appear in the LCD screen of your instrument.

MIDI-related explanations

CC#

is an abbreviation for Control Change Number.

In explanations of MIDI messages,

numbers in square

brackets [ ]

always indicate hexadecimal numbers.

iv

Table of Contents

Introduction .................................1

Overview.......................................... 1

Main features .............................................1

Overview of the modes ...............................3

Front and rear panel ......................... 5

Front panel.................................................5

Rear panel..................................................8

Objects and functions in the LCD screen .....10

Setup.............................................. 12

Connecting audio equipment etc................12

1. Connecting the AC/AC power supply.12

2. Connecting audio output devices..........12

3. Connecting pedals etc..............................13

Connections to MIDI equipment/computers.13

1. Connections to MIDI equipment............13

2. Connections to a computer.....................13

Inserting/removing a card in the

SD card slot ..............................................14

Connecting separately sold options............14

1. Audio input connections.........................14

2. SCSI connections.......................................14

Basic operation ............................... 15

Selecting modes, pages and tabs; setting

parameters...............................................15

1. Selecting modes........................................15

2. Selecting pages and tabs..........................15

3. Selecting parameters................................16

4. Setting a parameter ..................................16

Quick Start ................................18

Turning the power on/off ................ 18

1. Turning the power on............................18

2. Turning the power off............................18

Listening to the demo songs............. 19

Loading demo playback data ....................19

Selecting and playing a demo song in the

Sequencer mode .......................................19

Playing a cue list.......................................20

Selecting and playing a program......21

Selecting a program .................................21

Selecting and playing a

combination.....................................23

Selecting a combination............................23

Using controllers to modify the

sound..............................................24

Joystick....................................................24

SW1, SW2 ...............................................24

REALTIME CONTROLS [1], [2], [3], [4] ........25

Keyboard.................................................26

Foot pedals ..............................................26

Using the arpeggiator while you

play ................................................27

Using the arpeggiator in Program mode....27

Settings using controllers ........................... 27

Settings in the LCD screen ......................... 28

Using the arpeggiator as you play in

Combination mode ...................................29

Settings in the LCD screen ......................... 29

Playing with the RPPR (Realtime Pattern

Play/Recording) function..................31

Simple program editing....................32

Performance Edit ......................................32

Realtime controls ......................................32

Simple combination editing ..............33

An example of editing ..............................33

Sampling (recording a sample).........35

Sampling a sound and playing it back as

“one-shot” ...............................................35

Using the insert effect while you sample ....36

Assigning a name to the sample or

multisample..............................................37

Saving sample data..................................38

Converting a multisample into a program..38

Sampling and looping a drum phrase........39

v

Basic functions...........................42

Saving data.....................................42

Types of data that can be saved ................42

Writing to internal memory .......................43

Writing a program or combination........... 43

Writing global settings, user drum kits, and

user arpeggio patterns............................ 45

Saving on external media..........................46

MIDI data dump........................................47

Restoring the factory settings............48

Loading the preloaded data.......................48

Program mode ................................49

How a program is organized.....................49

Basic program editing ...............................49

Oscillator settings ........................................ 50

Controller settings .......................................51

Pitch settings................................................. 51

Filter settings ................................................ 52

Amplifier settings ........................................ 54

LFO settings.................................................. 55

Arpeggiator settings.................................... 55

BUS settings.................................................. 55

Insert Effect settings .................................... 55

Master Effect settings .................................. 55

More about Alternate Modulation..............56

Auto Song Setup function ..........................56

Combination mode ..........................57

How a combination is organized ...............57

Basic combination editing........................... 57

Timbre 1–8 program, pan and volume..... 58

Controller settings .......................................59

Settings for status, MIDI channel, and

playing mode........................................... 59

Note timing and scale settings................... 60

Layer and split settings............................... 60

Velocity switch settings ..............................61

MIDI filter settings....................................... 61

Arpeggiator settings.................................... 61

Bus settings...................................................61

Insert Effect settings .................................... 61

Master Effect settings .................................. 61

Auto Song Setup function ..........................62

Sequencer mode..............................63

Features of the sequencer..........................63

The structure of Sequencer mode ...............64

Songs..............................................................64

Patterns.......................................................... 64

Cue List.......................................................... 64

Producing a song......................................65

Creating the basic song ...............................65

Song editing methods..................................71

Creating and playing a Cue List................73

Creating and recording RPPR (Realtime Pattern

Play/Record) ............................................75

Creating RPPR data .....................................75

RPPR playback .............................................76

Realtime-recording an RPPR

performance .............................................76

Recording the sound of a combination or

program...................................................77

Auto Song Setup function...........................77

Copy From Combi (Sequencer mode page

menu commands)....................................78

Caution and other functions in Sequencer

mode .......................................................80

Recording on the TR..................................81

Recording a track,

and recording a pattern..........................81

Sampling mode............................... 86

Features of EXB-SMPL ...............................86

How Sampling mode is organized.............87

In Sampling mode........................................87

Samples and Multisamples.........................87

Sampling..................................................88

Preparations for sampling ..........................88

Manual sampling .........................................89

Auto sampling..............................................90

Creating multisample indexes and

sampling ...................................................91

Loop settings ............................................92

The grid display ...........................................92

Sample (waveform data) editing................93

Multisample editing ..................................94

Editing the indices .......................................94

Modifying the settings of an index............94

Converting a multisample to a program.....94

Using Time Slice to divide a sample and play it

in Sequencer mode...................................95

Global mode................................... 97

Creating a drum kit...................................97

About drum kits...........................................97

Editing a drum kit........................................98

Media mode.................................. 100

How Media mode is organized................100

Media that can be used..............................100

Formatting media ...................................100

SD card handling....................................100

About the write protect setting of an

SD card..................................................100

vi

Loading data ..........................................101

Types of data that can be loaded..............101

Data loading procedure.............................101

Saving data............................................102

Types of data that can be saved ...............102

Arpeggiator settings...................... 103

Arpeggiator settings for a program .........103

Arpeggiator on/off ....................................103

Arpeggiator settings...................................103

Linking the arpeggiator to a program.....105

Arpeggiator settings in Combination and

Sequencer modes....................................105

Arpeggiator on/off ....................................105

Arpeggiator settings...................................105

Linking the arpeggiator to the

combination............................................106

Creating a user arpeggio pattern.............107

About user arpeggio patterns...................107

Editing a user arpeggio pattern................107

Dual arpeggiator editing...........................110

Synchronizing the arpeggiator.................111

Synchronization between arpeggiators A

and B........................................................111

Synchronization between the arpeggiators

and sequencer in Sequencer mode......111

Synchronization with an external sequencer

in Program, Combination, or Sequencer

modes ......................................................111

Effects settings............................... 112

Effects in each mode................................112

Routing settings and effect settings...........112

Effect settings for a program.....................112

Effect settings in combination, and song 114

Effect settings in Sampling mode (requires

the EXB-SMPL option)..........................114

Effect settings for the AUDIO INPUT

(requires the EXB-SMPL option).........115

About dynamic modulation (Dmod)..........115

Other functions ............................. 117

Tuning to another instrument/

Transposing............................................117

Bypassing the effects...............................117

Specifying the function of the Assignable

Switch and Assignable Pedal...................117

Selecting different Velocity and Aftertouch

curves.....................................................118

Creating original scales...........................118

Changing the scale..................................118

Setting the function of [SW1] and [SW2] ..119

Setting the B-mode functions of REALTIME

CONTROLS [1]–[4] ..................................119

Adjusting the contrast (brightness) of the LCD

screen....................................................120

Using this instrument as a data filer.........120

Tap tempo control...................................120

Shortcuts................................................120

Appendices .............................121

Troubleshooting.............................121

Specifications and options..............124

Specifications .........................................124

Operating requirements for connection to a

computer................................................125

Options..................................................125

MIDI Implementation Chart.............126

Index.............................................127

1

Introduction

Overview

Introduction

Overview

Main features

Overview

The TR Music Workstation features Korg’s acclaimed

HI (Hyper Integrated) synthesis system.

It contains high-quality preset multisamples/pro-

grams/combinations, an effect section, plus a

sequencer, dual polyphonic arpeggiator, RPPR, four-

channel audio output, and numerous other functional-

ity.

Controllers such as the joystick, [SW1] and [SW2] keys,

REALTIME CONTROLS [1]–[4] knobs, or connected

pedals can be used to control ﬁlter or effects, allowing

you to modify the sound in realtime as you perform.

Arpeggiator gate or velocity, or the tempo of the arpeg-

giator or sequencer can also be controlled.

In addition, the optional EXB-SMPL sampling

upgrade can be installed to add two-channel audio

input and sampling functionality. (

☞p.35, 88, ☞PG

p.260)

The TR is the ideal music workstation for music pro-

duction or live performance.

HI (Hyper Integrated) synthesis system

The HI (Hyper Integrated) synthesis system is a PCM

tone generator system with full digital signal process-

ing that guarantees pristine sound, and features enor-

mous ﬂexibility in musical extensibility, modulation,

and effect routing.

Tone generator section:

• 64 MB of preset PCM ROM containing 470

multisamples and 518 drumsamples.

• The sampling frequency is 48 kHz, and the

maximum polyphony is 62 voices.

Filter/synthesis section:

• 24 dB/oct Low Pass Resonance type or 12 dB/oct

Low Pass & High Pass type filters can be used. A

wide variety of filter effects can be achieved, from

active sounds with aggressive resonance to subtle

tones using a high pass filter.

•A broad range of editing parameters gives you

control over every aspect of the sound.

Effect section:

• One insert effect (stereo-in/stereo-out), two master

effects (mono-in/stereo-out), and a three-band

master EQ (stereo-in/stereo-out) can all be used

simultaneously. You can select from 89 types of

effect algorithms, and edit them.

• Highly flexible effect routing is possible. Effects can

also be routed freely to the individual outputs.

Alternate Modulation and Effect Dynamic Modula-

tion:

• The synthesis section (filter etc.) provides Alternate

Modulation functionality, and the effect section

provides Effect Dynamic Modulation

functionality. This allows you to freely apply

modulation to parameters that affect the pitch,

filter, amp, EG, LFO, effects etc.

• LFO and delay time parameters can be

synchronized to MIDI clock/tempo. You can

synchronize sounds or effects to the tempo of the

sequencer or the arpeggiator.

Programs and combinations

• In the Program mode, the TR provides 512 user

programs, plus 128 programs + 9 drum sets for GM

compatibility.

When shipped from the factory, it is loaded with

high-quality programs that cover a wide range of

musical needs.

The 512 user programs can be modiﬁed by adjusting

the numerous editing parameters, the effects and

the arpeggiator, to create your own original pro-

grams.

• The TR provides 24 user drum kits and nine GM2-

compatible ROM drum kits. With the factory

settings, preset drum kits that cover a variety of

musical genres are provided. You can create your

own original drum kits by assigning a drumsample

or an original sampled sound to each note of the

keyboard. For each note, you can make filter and

amp settings, and even route the sound through

effects and to a individual audio output.

• The TR provides 384 user combinations. The

factory settings contain a wide variety of Preload

combinations.

A combination allows you to use layers, splits, or

velocity switches etc. to combine up to eight pro-

grams together with effects and two arpeggiators, in

order to create complex sounds that could not be

produced by a program. You can also make settings

that include external tone generators.

2

Sequencer

TR provides a high-performance 16-track MIDI

sequencer, with more than sufﬁcient power for use as a

stand-alone sequencer. The sequencer can serve as the

core that brings together TR’s numerous capabilities,

allowing it to serve as an integrated music worksta-

tion.

For more on TR’s sequencer (

☞p.63).

RPPR

TR features a RPPR (Realtime Pattern Play/Record-

ing) function.

In Sequencer mode, this function allows you to assign

preset patterns or user patterns (with a speciﬁed play-

back track) to individual keys on the keyboard, and

playback or record that pattern in realtime simply by

pressing the assigned key. Numerous preset patterns,

including patterns ideal for drum tracks, are built into

the internal memory.

Dual polyphonic arpeggiator

• Five preset arpeggio patterns (UP, DOWN, ALT1

ALT2, RANDOM) and 216 user arpeggio patterns

are provided. With the factory settings, these

contain a wide variety of preset user patterns.

In addition to providing conventional arpeggiator

functionality, the polyphonic arpeggiator of the TR

can respond to the pitches or timing at which you

play the keyboard, and produce a diverse range of

chords or phrases. This can be used to play a variety

of drum phrases (using the “Fixed Note Mode” that

is ideal for drums), bass phrases, or guitar and key-

board backing riffs. The arpeggiator is also effective

for use with subtly moving pads, synth sounds, or

sound effects.

In Combination mode, and Sequencer mode, the TR

provides dual arpeggiators that can simultaneously

play two arpeggio patterns. You can apply separate

arpeggio patterns to drum and bass programs, or

use keyboard splits or velocity to switch between

arpeggio patterns for an even more dynamic perfor-

mance.

4 channel audio output

• In addition to the L/MONO and R main stereo

audio outputs, TR provides two individual audio

outputs, for a total of four channels of audio

output. The sound from each oscillator, drum,

timbre/track, or insertion effect can be routed

freely to any output.

EXB-SMPL sampling upgrade

The following functionality can be added by installing

the separately sold EXB-SMPL option.

• Sampling mode is added. Input sources from the

two-channel audio inputs can be sampled and

edited to create original multisamples or samples,

which can then be used in a program or drum kit.

For details on the features of Sampling mode, refer

to p.86.

• Two-channel audio input is added. This two-

channel audio input allows 48 kHz 16 bit linear

mono/stereo sampling. A MIC or LINE level select

switch and level adjustment control supports a

wide range of external audio sources, from mic

level to line level.

The audio input can also be routed to the effects.

You can apply an effect while sampling, or use the

TR as a 2-in/4-out effect processor.

•A SCSI connector is added, allowing external SCSI

devices such as hard disks to be connected. A

connected external SCSI device can be used in the

same way as an SD card to save or load data.

3

Introduction

Overview

Overview of the modes

The TR has a large number of functions that let you

play and edit programs and combinations, record and

play sequence data, and manage data on media. The

largest unit used to organize these functions is called a

mode. The TR has ﬁve modes.

If the separately sold EXB-SMPL option is installed,

Sampling mode will be added (for a total of six

modes), and you will be able to record and edit sam-

ples.

Program mode

• Select and play programs

You can choose programs from rewritable banks A,

B, C, and D which contain a total of 512 programs,

and non-rewritable bank G (128 programs compati-

ble with the GM standard, and nine drum pro-

grams).

• Edit a program

Make settings for the oscillator, ﬁlter, amp, EG, LFO,

effects, and arpeggiator.

Select a multisample (the following multisamples

are available)

• 470 internal multisamples (ROM, EX)

• Multisamples (RAM) created in Sampling mode

(if the separately sold EXB-SMPL option is

installed)

• Create drum programs using a drum kit (created

in Global mode)

Combination mode

• Select and play combinations

A combination is a set of two or more programs (a

maximum of eight), and allows you to produce

complex sounds that could not be created by an

individual program.

You can choose combinations from rewritable banks

A, B, and C which contain a total of 384 combina-

tions.

• Edit a combination

Make settings for volume, pan, layer/split etc. for

each timbre (program), and make settings for effects

and the two arpeggiators etc.

Sequencer mode

• Use the 16-track sequencer to record and playback

songs.

• Make effect settings for the song.

• You can record a performance using the

arpeggiator(s) into a song or pattern.

• You can use a cue list to set up consecutive

playback of multiple songs, and specify the number

of repeats for each song.

• You can use a maximum of 20 cue lists, 200 songs,

and 150 preset patterns. One song can use as many

as 100 patterns.

• The TR can be used as a 16-track multitimbral tone

generator.

IFX

MFX 1

MFX 2

MEQ

Insert / Master Effect

Arpeggiator

OSC 1

Multi Sample - H

Drum Kit

Multi Sample - L

PITCH1

FILTER1 AMP1

OSC 2

Multi Sample - L

PITCH2

FILTER2

AMP2

Multi Sample - H

PROGRAM MODE

PROGRAM

IFX

MFX 1

MFX 2

MEQ

TRACK 1

TRACK 8

TRACK 2

TRACK 3

TRACK 4

TRACK 5

TRACK 6

TRACK 7

PROGRAM

Insert /Master Effect

Arpeggiator - A

Arpeggiatpr - B

SEQUENCER

PROGRAM

TRACK 9

TRACK 16

TRACK 10

TRACK 11

TRACK 12

TRACK 13

TRACK 14

TRACK 15

PROGRAM

IFX

MFX 1

MFX 2

MEQ

TIMBRE 1

TIMBRE 8

TIMBRE 2

TIMBRE 3

TIMBRE 4

TIMBRE 5

TIMBRE 6

TIMBRE 7

PROGRAM

Insert /Master Effect

Arpeggiator - A

Arpeggiatpr - B

COMBINATION MODE

GLOBAL MODE

Drum Sample / Sample - L

Drum Sample / Sample - H

Key

Assign

ARPEGGIATOR PATTERN

User Pattern: P0 - 4

DRUM KIT

User Pattern: U00 - 215

Sample

SAMPLING MODE (if the separately sold EXB-SMPL option is installed)

Sample

IFX

Insert Effect

AUDIO INPUT

1

AUDIO INPUT

2

MEDIA MODE

Multi Sample

4

• Create and playback patterns in realtime, using the

RPPR (Realtime Pattern Play/Recording) function.

Global mode

• Make settings that affect the entire TR, such as

master tune and global MIDI channel.

• Create drum kits (24 kits), user arpeggio patterns

(216 patterns), and user scales (16 one-octave scales

and 1 all-note scale).

• Create drum kits using the 518 internal drum

samples (ROM, EX). You can also use samples

(RAM) that were created in Sampling mode

(requires the separately sold EXB-SMPL option).

• Set the function of the assignable pedals and

assignable switches.

• Transmit data dumps of MIDI exclusive data.

• Adjust the input level from AUDIO INPUT 1 and 2

(if the EXB-SMPL option is installed). This setting is

valid outside of Sampling mode. The internal

effects can be applied to the external input sound.

The settings for Sampling mode are made

independently in Sampling mode itself.

Media mode

• Data of each mode can be saved and loaded using

the SD card slot or an external SCSI device (if the

separately sold EXB-SMPL option is installed).

• Media such as an SD card or hard drive (EXB-SMPL

option required) can be formatted, and then data

can be managed by copying etc.

• Korg format, AKAI, AIFF, and WAVE format

sample data can be loaded. Sample data can also be

saved in Korg format, or exported in AIFF or

WAVE format (if the separately sold EXB-SMPL

option is installed).

• Songs that you created in Sequencer mode can be

saved in SMF format. SMF files can be loaded as

Sequencer mode songs.

• You can use the Data Filer function (to save/load

MIDI exclusive data).

Sampling mode

(If the EXB-SMPL option is installed)

• An external audio device or mic connected to the

rear panel AUDIO INPUT jacks can be sampled

(recorded as a sample). An insert effect can also be

applied to the select input sound while it is being

sampled.

• Waveform data that was sampled or loaded in

Media mode can be modified using a variety of

editing functions, such as adjusting the loop point,

using Time Slice, or Time Stretch.

• You can edit multisamples (which consist of

multiple samples).

• You can convert a multisample into a program.

When this conversion is performed, a multisample

created in Sampling mode can be used in Program,

Combination, and Sequencer modes.

5

Introduction

Front and rear panel

Front panel

1. [SW1] key, [SW2] key

These keys are on/off switches for the functions to

which they were assigned in Program, Combination,

Sequencer and Sampling modes (if the EXB-SMPL

option is installed). When on, the key will light

(

☞p.24).

2. Joystick

This controls pitch or modulation, etc.

Move the joystick up/down or left/right (+Y, –Y,

–X, +X) to control (

☞p.24).

Various program parameters and effect parameters

will determine what is controlled by the joystick.

3. Headphone jack

A set of headphones with a (1/4") stereo phone plug

can be connected here.

The output from the L/MONO and R OUTPUT jacks

can be monitored in stereo through the headphones.

4. [VOLUME] slider

This adjusts the volume that is output from the OUT-

PUT jacks (L/MONO, R) and the headphone jack.

5. REALTIME CONTROLS

Use the [SELECT] key to select realtime controller

mode A/B/C, and use knobs [1]–[4] to control the

tone, effects, MIDI control changes, and arpeggiator

etc. while you perform. (

☞p.25, 27)

[SELECT] key

This key switches the realtime controller between A-

mode, B-mode, and C-mode. The LED of the selected

mode will light.

[ARP ON/OFF] key

This key turns the arpeggiator on/off. When on, the

key will light.

[1], [2], [3], [4] knob

A-mode

[1] LPF CUTOFF:

Controls the cutoff frequency of the low pass ﬁlter.

[2] RESONANCE/HPF:

Controls the ﬁlter resonance level or the high pass ﬁlter

cutoff frequency.

1

3

4

7

9

10

13

12

2

5

68

11

6

[3] EG-INTENSITY:

Controls the ﬁlter EG intensity.

[4] EG-RELEASE:

Controls the ﬁlter/amp release time.

B-mode

[1] ASSIGNABLE 1:

[2] ASSIGNABLE 2:

[3] ASSIGNABLE 3:

[4] ASSIGNABLE 4:

Controls the functions that are assigned in each mode

(Program, Combination, Sequencer, or Sampling (if the

EXB-SMPL option is installed)).

C-mode

[1] ———: not used

[2] ARP-GATE:

Controls the gate time (note duration) of the arpeggi-

ated notes. At the center position (12 o’clock), the set-

ting of the arpeggiator “Gate” parameter will be used.

Rotating the knob toward the left will shorten the time,

and rotating it toward the right will lengthen the time.

[3] ARP-VELOCITY:

Controls the velocity (playing strength) of the arpeggi-

ated notes. At the center position (12 o’clock), the set-

ting of the arpeggiator “Velocity” parameter will be

used. Rotating the knob toward the left will weaken

the velocity, and rotating it toward the right will

strengthen the velocity.

[4] TEMPO:

Controls the tempo of the arpeggiator or of the

Sequencer mode .

The LED beside “TEMPO” will blink at quarter note

intervals of the speciﬁed tempo.

6. Mode keys, [COMPARE] key

These keys are used to enter each mode.

Pressing a key will enter the corresponding mode (the

key will light). (

☞p.15)

[COMBI] key

Combination mode will be selected.

[PROG] key

Program mode will be selected.

[SEQ] key

Sequencer mode will be selected.

[GLOBAL] key

Global mode will be selected

[MEDIA] key

Media mode will be selected.

[COMPARE] key

Use this key when you wish to compare the sound of

the program or combination that you are currently

editing with the un-edited sound that was written into

memory. You can also use this key to make “before and

after” comparisons when recording or editing in

Sequencer mode (

☞p.16).

[SAMPLING] (EXB-SMPL) key

This key selects the Sampling mode.

This is valid only if the separately sold EXB-SMPL

option is installed.

If the separately sold EXB-SMPL option is not

installed, pressing the [SAMPLING] key will cause

a message of “No Sampling Upgrade Installed” to

be displayed.

7. [TIMBRE/TRACK] key,

[F1 T1/T9] … [F8 T8/T16] keys

Function [F1]–[F8] keys

These keys select the tabs that are displayed in each

page. They are also used to execute utilities and other

functions.

Timbre/track select [T1/T9]–[T8/T16] keys

By holding down the [TIMBRE/TRACK] key and

pressing a [T1/T9]–[T8/T16] key, you can select the

timbre/track parameters corresponding to the key

number.

When a single page displays the parameters for tim-

bres 1–8 of a Combination or for tracks 1–8/9–16 of

Sequencer mode, these keys select one of these tim-

bres/tracks.

8. LCD screen

Here you can select pages, and parameters, and set val-

ues. (

☞p.10)

9. VALUE controllers

The following VALUE controllers are used to set the

value of the selected parameter (

☞p.16).

7

Introduction

Front and rear panel

[VALUE] dial

Use this dial to modify the value of the parameter.

[INC]/[DEC] keys

These are used to increase or decrease the parameter

value in steps of one. It is convenient to use these to

make ﬁne adjustments.

Numeric keys [0] – [9], [ENTER] key, [–] key,

[./HOLD] key

Use these keys to numerically input a parameter value.

Use numeric keys [0]–[9], the [–] key, and the [./

HOLD] key to enter the value, and press the [ENTER]

key to conﬁrm it. The [./HOLD] key lets you input a

value with a decimal point. The [–] key inverts the sign

(+/–) of the parameter value.

In addition, [./HOLD] can be used if you wish to select

sounds by category in program or combination mode.

By holding down the [ENTER] key and pressing a

numeric key [0]–[9], you can select up to ten utility

menu commands for the current page.

10. [CATEGORY] key, [AUDITION] key

[CATEGORY] key

In each mode, you can directly access the utility menu

“Select by Category” by choosing a parameter that can

be selected by category and then pressing the [Cate-

gory] key.

This allows you to view and select programs or combi-

nations by category. (

☞p.22)

[AUDITION] key

This key activates the Audition function, which plays

a riff (phrase) suitable for each preloaded or preset pro-

gram.

In Program mode, pressing the [AUDITION] key (the

key will light) will cause the audition riff to play

repeatedly.

In Sampling mode (if the EXB-SMPL option is

installed), the selected sample will be played.

11.[EXIT] key, [MENU PAGE +/–] key, CURSOR

keys [ ], [

–], [ ], [ +]

[EXIT] key

In Program, Combination, Sequencer, Sampling (if the

separately sold EXB-SMPL option is installed), and

Global modes, pressing this key from anywhere other

than page 1.1 will take you to page 1.1 of that mode.

When a dialog box is open, this key will cancel the set-

tings made in the dialog box and close the dialog box

(corresponds to the “Cancel”). If a Utility menu or

page menu is open, pressing [EXIT] will close the

menu.

[MENU PAGE +/–] key

Use this key to select different pages on screen. When

you press this key, a list of the pages within the mode

will appear in the LCD screen. Use the function key

[F1]–[F7] or cursor keys [ ], [ ], [ ], [ ] to select the

desired page, and press the [F8] key to move to the

selected page.

You can also move to a desired page by holding down

the [MENU] key and using numeric keys [1]–[7] to

enter a two-digit page number.

In addition, you can hold down the [MENU] key and

use cursor keys [ ], [ ] to switch pages in the order of

1.1→2.1→2.2→2.3. (

☞p.15)

CURSOR keys [ ], [ –], [ ], [ +]

Use these keys to select different parameters on screen.

In addition, you can hold down the [MENU] key and

use cursor keys [ ], [ ] to switch pages in the order of

1.1→2.1→2.2→2.3. (

☞p.15)

12.BANK keys

These keys are used to switch Program/Combination

banks.

PROG BANK: [A], [B], [C], [D], [GM]

When selecting programs, use keys [A], [B], [C], [D],

and [GM]. The key of the selected bank will light.

Each time you press [GM], you will cycle through the

GM banks and the drum bank as follows: G, g(d), G ...

etc.

COMBI BANK: [A], [B], [C]

When selecting combinations, use keys [A], [B], and

[C]. The LED of the selected bank will light.

In Combination, and Sequencer modes when the edit

cell (highlighted area) is located at the program of a

timbre or track, you can use the BANK keys to select

the bank of the program. The bank key of the program

selected for that timbre/track will light.

In dialog boxes such as Write Program or Write Com-

bination, these keys are used to specify the program or

combination bank that will be the writing destination,

etc.

8

13.SEQUENCER/SAMPLING

(If the separately sold EXB-SMPL option is

installed)

[PAUSE] key

This key pauses playback of a song or cue list (the key

will light). Press the key again to cancel Pause (the key

will go dark).

[ REW] key

This key rewinds playback of a song or cue list.

Rewind will occur when you press the key (the key

will light). (This will not operate during recording.)

[FF ] key

This key fast-forwards playback of a song or cue list.

Fast-forward will occur when you press the key (the

key will light). (This will not operate during record-

ing.)

[LOCATE] key

This key resets the playback location of a song or cue

list to a speciﬁed location. You can also press this key

when “stuck notes” occur for some reason.

[REC/WRITE] key

When you press this key in Sequencer mode, the TR

will enter recording-ready mode (the key will light). If

you then press the [START/STOP] key, recording will

start. (

☞p.81)

When you press this key in Program, Combination, or

Global modes, a dialog box will appear. If you then

press the [F8] (“OK”) key, the edited content will be

written. (

☞p.43, 45)

When you press this key in Sampling mode (if the

EXB-SMPL option is installed) and then press the

[START/STOP] key, sample recording will begin.

(

☞p.35)

[START/STOP] key

In Sequencer mode, this key starts/stops song record-

ing/playback, or cue list playback. (The key will blink

in time with the beat during recording or playback.)

In Sampling mode (if the EXB-SMPL option is

installed), press the [REC/WRITE] key and then press

the [START/STOP] key to start/stop sample recording.

In the SMPL 2.1–2: Sample Edit, Edit2 page, pressing

this key will sound the sample.

Rear panel

1. SD card slot

You can insert an SD card in this slot.

Refer to p.14 for details on inserting, removing, and

handling media.

2. USB B connector (for connecting to a

computer)

You can connect your computer to this connector.

Using a single USB cable, your TR can send and receive

MIDI information to and from a computer . This elimi-

nates the need for a MIDI interface and the associated

cables. (

☞PG p.233)

What is USB?

USB stands for Universal Serial Bus, and is an interface

for transferring data between a computer, a keyboard

and/or peripheral devices.

The USB connector of the TR is only able to trans-

mit and receive MIDI data.

3. [POWER] switch

This switch turns the power on/off (☞p.18).

4. AC power supply connector (~AC9V)

Connect this to the included AC/AC power supply.

After connecting the power supply cable to TR, con-

nect the other end to an AC outlet (

☞p.12).

5. AUDIO OUTPUT

Connect these outputs to the input jacks of your amp

or mixer. In addition to the L/MONO and R main ste-

reo audio outputs, TR provides two individual audio

outputs. The sound from each oscillator, drum, tim-

bre/track, or insertion effect can be freely routed to

any output (

☞p.112–).

3

4

6

78

2

1

5

9

Introduction

Front and rear panel

(MAIN) L/MONO, R

These are unbalanced phone jacks (☞p.12).

These are the main audio output jacks. By setting “Bus

Select” to L/R, the output from an oscillator, an inser-

tion effect, an individual drum part, or the metronome

can be output to the (MAIN) L/MONO and R jacks.

When making connections in stereo, use L/MONO

and R. When making connections in mono, use the L/

MONO jack.

(INDIVIDUAL) 1, 2

These are unbalanced phone jacks (☞p.12).

These are individual (independent) audio output jacks.

By cycling the “Bus Select” through 1, 2, 1/2 an oscilla-

tor, an insertion effect, an individual drum part, or the

metronome etc. can be assigned to be output from the

(INDIVIDUAL) 1, 2 jacks. The output from the 1, 2

jacks is not affected by the [VOLUME] slider.

6. Pedal connections

ASSIGNABLE PEDAL jack

The separately sold Korg XVP-10 EXP/VOL pedal or

EXP-2 foot controller (options) can be connected to this

jack. (

☞p.13).

Its function can be assigned in Global mode, allowing

you to use the pedal to control the volume, etc.

(

☞p.117)

ASSIGNABLE SWITCH jack

A separately sold on/off foot switch such as the Korg

PS-1 foot switch can be connected here (

☞p.13).

Its function can be assigned in Global mode, allowing

you to use the foot switch as a modulation controller,

to select programs or combinations, or to start/stop the

sequencer (

☞p.117).

DAMPER jack

A separately sold switch-type pedal such as the Korg

DS-1H damper pedal can be connected here.

If a DS-1H is connected, it will function as a half-

damper pedal. In order to ensure that the half-damper

pedal functions correctly, please adjust the polarity and

the sensitivity (

☞PG p.126, 128).

If any other switch-type pedal is connected, it will

function as a damper switch.

Set the polarity according to the pedal that you con-

nected. (

☞PG p.128)

7. MIDI

MIDI IN connector

Musical data and sound settings etc. are received at

this connector.

Use this to play TR from another connected MIDI

device (

☞PG p.233).

MIDI OUT connector

Musical data and sound settings etc. are transmitted

from this connector.

Use this to control another connected MIDI device

from TR (

☞PG p.233).

If MIDI data is being transmitted from the TR via

USB to your computer, transmission from the

MIDI OUT connector is halted.

MIDI THRU connector

Musical data and sound settings etc. that are received

at the MIDI IN connector are re-transmitted without

change from the MIDI THRU connector.

You can use this to connect multiple MIDI devices via

MIDI cables (

☞PG p.233).

8. EXB-SMPL

(If the separately sold EXB-SMPL option is

installed)

These connectors are used to sample mono or stereo

audio from a mic or audio device (

☞p.35, 39), or to use

the internal effect processor to apply effects. (

☞p.115)

The MIC/LINE level select switch ([MIC/LINE]

switch) and the level adjustment knob ([LEVEL] knob)

allow a wide range of audio sources to be input, from

mic level to line level.

SCSI connector

Use a SCSI cable to connect this to a SCSI-compatible

device (hard disk drive, CD-ROM drive, etc.). (

☞ EXB-

SMPL owner’s manual)

AUDIO INPUT 1, 2 jacks

These are unbalanced phone audio input jacks. (

☞p.14)

Connect them to the OUTPUT jack(s) of your external

audio device or mic.

[LEVEL] knob

This knob adjusts the input level of the AUDIO INPUT

1, 2 jacks. (

☞p.35)

[MIC/LINE] switch

This switch selects the input level of the AUDIO

INPUT 1, 2 jacks. (

☞p.35)

10

Objects and functions in the LCD

screen

a: Current page

This indicates the currently selected page within

the mode. From the left, this area shows the mode

name, page number:name, tab name, and the

parameter name of the edit cell.

b: Tab

Most pages are divided into two or more tabs. By

pressing the closest function key [F1]–[F7], you can

select a tab to access the corresponding page.

c: Parameters

The parameters for various settings are displayed

in the LCD screen. Use cursor keys [ ], [ ], [ ],

[] to select the desired parameter.

d: Edit cell

When you use the cursor keys [ ], [ ], [ ], [ ],

the selected parameter will be highlighted in the

LCD screen. This area is called the edit cell, and

your editing will affect the highlighted area.

The parameter value of the edit cell can be modi-

ﬁed using VALUE controllers such as the [VALUE]

dial or the [INC]/[DEC] keys (

☞p.16). For parame-

ters that accept a key number or a velocity value,

you can also hold down the [ENTER] key and play

a note on the keyboard to enter the key number or

velocity value.

e: Check box

Use cursor keys [ ], [ ], [ ], [ ] to select a check

box (edit cell), and use a VALUE controller such as

the [VALUE] dial or the [INC]/[DEC] keys to add

or remove the check mark.

When checked, the parameter will function, when

unchecked, the parameter will not function.

f: Function buttons

By pressing the function key [F1]–[F8] nearest this

button, you can turn various functions on/off.

, :

In Media mode, these select the current directory.

:

Accesses the utility menu where you can execute

utility menu commands.

Other function buttons examples

* Utility menu

In each page, you can press the “UTILITY” func-

tion button (the [F8] key) to access the utility

menu. The utility menu contains commands that

can be used in that page. The utility menu that

appears will differ depending on the page that is

selected.

You can also select up to ten utility menu com-

mands by holding down the [ENTER] key and

pressing a numeric key [0]–[9].

Press the [EXIT] key to close the utility menu.

For , press the [F7] key to select the desired

utility menu command. You can also use the cur-

sor keys [ ], [ ], [ ], [ ] to make your selection.

For , press the [F8] key to open the dialog

box of the selected utility menu command.

This key also switches the status of commands that

you check or uncheck.

b: Tab

a: Current page d: Edit cell e: Check box

c: Parameter f: Function buttons

Mode name Parameter namePage number:name

Tab name

Sequencer mode: EDIT/DONE, INSERT, CUT,

COPY, JUMP, DONE, Tie, Rest,

Back, Done (used in Cue List,

Event Edit, Step Recording)

REVERT (copy and paste RPPR

settings)

Global mode: TEXT, KEY+, –

Sampling mode (if the separately sold EXB-SMPL

option is installed):

INSERT, CUT, COPY, CREATE

(create multisample), L/R,

ZOOM

11

Introduction

Front and rear panel

* Dialog boxes

When you select a utility menu command etc., a

dialog box will open.

Use the cursor keys [ ], [ ], [ ], [ ] to select

parameters. Use the VALUE controllers (

☞p.16) to

input the parameter values. When selecting pro-

gram or combination numbers in a dialog box, you

can use the BANK [A]–[GM] keys in addition to

the VALUE controllers.

As in the utility menu, press the function key [F1]–

[F8] nearest etc. (function button 2) to access

the execution or operation screen. In some cases, a

dialog box will appear. Follow the directions

shown in the dialog box.

To execute, select (press the [F8] key). To

cancel without executing, select (press the

[F7] key). The dialog box will close. The [EXIT] key

is equivalent to “Cancel,” “Done,” or “Exit.”

* Function buttons 2

Press the function key [F1]–[F8] nearest this button

to execute the function.

:

Utility menu, etc.

*Text dialog box

When you use the function keys to select , a

text dialog box will appear.

In this dialog box you can rename text (e.g., the

name of a program, combination, or song). (

☞p.44)

* Scroll bar

This indicates that the list contains selections or

parameters that cannot all be shown in the screen

at once. Use the cursor keys [ ], [ ], [ ], [ ] to

move within the list.

* Page menu

In Combination, Program, Sequencer, Global, or

Sampling (if the separately sold EXB-SMPL option

is installed) modes, pressing the [MENU] key will

display a list of the pages in that mode. (The page

in which you where when you pressed the

[MENU] key will be highlighted.)

To select a page, press the nearest function key

[F1]–[F7]. By pressing the same key you can move

consecutively downward. You can also use cursor

keys [ ], [ ], [ ], [ ] to move left/up/down/

right.

You can also move to the desired page by holding

down the [MENU] key and using numeric keys

[0]–[7] to enter a two-digit page number. In addi-

tion, you can hold down the [MENU] key and use

the cursor keys [ ], [ ] to move in steps of one

page; in the example shown below, this would be

Play → P/M → Ctrl → Prm1 → ... etc.

* Other objects

To use slider- or knob-shaped objects, use the cur-

sor keys [ ], [ ], [ ], [ ] to select the desired

item, and use the VALUE controllers to adjust the

value.

Other types of objects are shown in the effect rout-

ing screen. (

☞p.112)

Scroll

bar

KnobsSliders

Routing

12

Setup

Connecting audio equipment etc.

Connections must be made with the power turned

off. Please be aware that careless operation may

damage your speaker system or cause malfunc-

tions.

1. Connecting the AC/AC power

supply

Connect the included AC/AC power supply to the

AC power supply inlet of TR, and then connect the

other end of the cable to an AC outlet.

2. Connecting audio output devices

AUDIO OUTPUT (MAIN) L/MONO, R,

(INDIVIDUAL) 1, 2

Here, you can connect a set of ampliﬁed monitor

speakers or your audio system to output TR’s sound.

If you wish to use the AUDIO OUTPUT (INDIVID-

UAL) 1–2 jacks of TR, we recommend that you use a

mixer.

If you playback TR through your stereo audio sys-

tem, be aware that high volumes may damage

your speakers. Be careful not to raise the volume

excessively.

Connect the AUDIO OUTPUT (MAIN) L/MONO

and R jacks to the INPUT jacks of your powered

monitor system, mixer etc.

L/MONO and R are the main outputs. If you are

outputting in stereo, make connections to the

(MAIN) L/MONO jack and the R jack. If you are

outputting in monaural, make connections to the

(MAIN) L/MONO jack. We recommend that you

playback in stereo if possible.

If you wish to output from the AUDIO OUTPUT

(INDIVIDUAL) 1, 2, jacks, connect these jacks to

your mixer, and then connect the mixer output to

the INPUT of your powered monitor system etc.

For details on the output of each jack (

☞p.112–

“Routing”).

Headphones

When using headphones, plug them into the head-

phones jack located on the front panel.

Power Switch

PHONES

Headphones

to an AC outlet

AC/AC power supply

Connecting the power cable

Connection to a computer

INPUT

PHONES

Headphones

Connecting audio output devices

Powered monitors, etc.

INPUT

OUTPUT

Connecting pedals etc

Connecting separately sold

Connecting MIDI equipment

USB cable

computer

13

Introduction

Setup

3. Connecting pedals etc.

Foot pedal connections

A foot pedal can be connected to control the volume or

other functions.

Connect a separately sold Korg assignable pedal such

as the XVP-10 EXP/VOL or EXP-2 to the rear panel

ASSIGNABLE PEDAL jack.

The function controlled by the foot pedal is speciﬁed in

GLOBAL 1.1–3: System, Foot page “Foot Pedal

Assign” (

☞p.117, PG p.127, 227).

Foot switch connections

A foot switch controls sostenuto, soft pedal on/off,

arpeggiator on/off, to select programs or combina-

tions, and to start/stop the sequencer etc.

Connect a separately sold Korg foot switch such as the

PS-1 to the rear panel ASSIGNABLE SWITCH jack.

The function that will be controlled by the foot switch

and the polarity of the foot switch can be set in GLO-

BAL 1.1–3: System, Foot page “Foot SW Assign,” and

“Foot SW Polarity” (

☞p.117, PG p.127, 226).

Damper pedal connections

Allows you to sustain the sound while playing.

Connect a Korg DS-1H damper pedal (separately sold

option) to the rear panel DAMPER jack. If a DS-1H is

connected, you can produce half-damper effects.

The polarity of the damper pedal can be set in GLO-

BAL 1.1–3: System, Foot page “Damper Polarity,” and

its sensitivity can be adjusted by the GLOBAL 1.1–1

System utility menu command “Half Damper Calibra-

tion.” (

☞PG p.126, 128)

Connections to MIDI equipment/

computers

1. Connections to MIDI equipment

The keyboard, controllers, and sequencer etc. of TR can

be used to control an external MIDI tone generator.

Conversely, another MIDI keyboard or sequencer can

control the tone generator of TR to produce sound.

Use MIDI cables to connect the MIDI connectors

of TR with the MIDI connectors of your external

device.

☞ PG p.233 “MIDI applications – Connecting MIDI

devices/computers”

If MIDI data is being transmitted from the TR via

USB to your computer, transmission from the

MIDI OUT connector is halted.

2. Connections to a computer

Your performance on the TR, as well as controller and

sequencer data, can be sent to a computer, and the tone

generator of the TR can be played from the computer

either via USB or via a MIDI interface.

You can use a MIDI interface to connect the MIDI

connectors of TR to the MIDI connectors of your

computer.

You can connect the TR’s USB B connector to the

USB connector of your computer.

☞ PG p.233 “MIDI applications – Connecting MIDI

devices/computers”

Some USB-MIDI interfaces may not be able to

transmit or receive the TR’s MIDI exclusive mes-

sages.

The USB connector of the TR is only able to trans-

mit and receive MIDI data.

14

Inserting/removing a card in the

SD card slot

If an SD card is inserted in the SD card slot, you can

use it to save or load various types of TR data.

Inserting a card

1 Insert an SD card in the SD card slot.

With the card label facing upward, insert the con-

nector end of the card into the SD card slot and

press it in until you hear a click.

Make sure that the card is oriented correctly when

you insert it. Forcing it in the wrong direction may

damage the slot or the card, and the data may be

lost.

Removing a card

Never remove an SD card from the slot while load-

ing, saving, or formatting is in progress.

1 Remove the card from the SD card slot.

Press the card inward; you will hear a click, and the

card will pop out part-way, allowing you to pull it

completely out.

Refer to the owner’s manual included with your

card, and observe the guidelines for handling and

use.

Connecting separately sold

options

By installing the separately sold EXB-SMPL option you

can add two channels of audio input jacks and a SCSI

connector.

For details on installing the EXB-SMPL, refer to PG

p.260.

1. Audio input connections

Connect a mic or the OUTPUT jacks of an external

audio device to the AUDIO INPUT 1, 2 jacks when you

want to sample in Sampling mode (if the separately

sold EXB-SMPL option is installed), or in Program,

Combination, or Sequencer mode when you want to

apply an internal effect to an external input sound and

output the processed sound from the OUTPUT jacks.

For details on connections when sampling in Sam-

pling mode, refer to p.35.

For details on connections when applying an

effect in other modes and outputting to the OUT-

PUT jacks, refer to p.115.

2. SCSI connections

You can connect SCSI-compatible devices (hard disks,

CD-ROM drives etc.). (

☞EXB-SMPL Operation Man-

ual)

SD card

SD card slot

Guitar

CD player, analog record player, etc.

If a passive type guitar (a guitar

without an internal preamp) is

connected, it will not be possible to

sample at an appropriate level due to

the impedance mismatch. Such

instruments must be connected via a

preamp or effect unit.

Effect processor etc.

Page is loading ...

Korg TR User manual

This manual is also suitable for

Korg TR User manual

Related papers

Other documents