Honda Honda Engines G400 Electric Start Owner's manual

Honda
Brand
Honda
Model
Honda Engines G400 Electric Start
Category
Engine
Type
Owner's manual

This manual is also suitable for

Honda Honda Engines G400 Electric Start is a reliable and powerful engine that is perfect for a variety of applications. With its 10 horsepower and 2.3 kg-m of torque, it can easily handle even the toughest tasks. The electric starter makes it easy to get started, and the counterclockwise PTO shaft rotation provides versatility for a variety of attachments.

The G400 is also fuel-efficient, consuming only 270 g/hp-h (0.59 lb/hp-h). This makes it an economical choice for long-term use. And with its dry weight of only 33 kg (72.7 lb), it is easy to transport and maneuver.

Honda Honda Engines G400 Electric Start is a reliable and powerful engine that is perfect for a variety of applications. With its 10 horsepower and 2.3 kg-m of torque, it can easily handle even the toughest tasks. The electric starter makes it easy to get started, and the counterclockwise PTO shaft rotation provides versatility for a variety of attachments.

The G400 is also fuel-efficient, consuming only 270 g/hp-h (0.59 lb/hp-h). This makes it an economical choice for long-term use. And with its dry weight of only 33 kg (72.7 lb), it is easy to transport and maneuver.

Click SAVE to save this manual to your computer. Thank you for choosing Honda.
FOR
SAFE
OPERATION
WARNING:
*
To prevent fire hazards and to provide adequate ventilation, keep the engine at least
3
ft away from
buildings and other equipment, during operation.
*
Do
not place flammable objects, such as, gasoline, matches, etc., close
to
the engine while it is running.
*
Refuel in a well ventilated area
with
the engine stopped. Gasoline is flammable and explosive under certain
conditions.
*
Do
not smok'e or allow flames or sparks where the engine is refueled or where gasoline is stored.
*
Do
not overfill the tank. There should be no fuel in the filler neck. Make sure that the filler cap is closed
*
If
any fuel is spilled, make sure the area
is
dry before starting.
*
Operate the engine
on
a level surface to prevent fuel spillage.
*
This engine
is
not equipped with
a
spark
arrester, and operation may be illegal in some
areas. Check local laws and regulations before
operation.
securely.
WARNING:
*
Exhaust contains poisonous carbon monoxide
Avoid inhalation
of
exhaust gases. Never
engine in a closed garage or confined area.
gas.
run
Check
cleaner
for
dirt
j
Check cleaner
tor
rut
or obstruction of elc-
i
or
obstruction
of
ele.
Check oil
level
and con-
dition.
~ ments.
i
ment.
,
f
--I
Check battery condition
+Be
sure
the
nuid
level
of
each
dl is
+Add distilled water if necessary.
+Check battery
@
2nd
Q
terminals
for
between upper and lower
levcl
marks.
proper
connection.
\
Check reduction
gear
oil
level
Fill
with
"SE"
rated
SAE
1OW-40
engine oil, if nccossary.
<
l/2
>
Fuel
tiller
an
Fuel valve
Air
cleaner
Throttle
lever
Engine
switch Spark plug
.
.,
....
..
''
Fill
sump
%th
"SE"
rated
SAE
1OW-40
engine
oil.
\'
\
First
20
Hrs.
operating Every
50
Hrs. operating
CHANGE ENGINE OIL AND REDUCTION GEAR OIL CLEAN AIR CLEANER ELEMENT ing in a dusty area.
Clean more frequently if operat-
ing solvent. After drying, soak in
oil and squeeze out the excess. After hand tightening oil filler cap, tighten
with
a
lever
*
Wash
“B”
and
“C”
in cleaning
solvent. After drying, refill with
clean engine
oil
up
to
oil level
mark.
*
Tap
“D”
and “E” lightly or blow
clean by applying compressed air
from the inside of the elements.
~-
,
Every
100
Hrs.
operating
I
WARNING
CHANGE ENGINE OIL CLEAN FUEL STRAINER CLEAN SPARKPLUG ANDCHECK
GAP
,
Do not use gasoline or
low
flash
,
point solvents for cleaning. They are
ilammable and explosive under cer-
0.6
-
0.7
mrn
(.024
-
,027
in) tain conditions.
Use NGK
B4H
or BR4HS
wash
removed parts
m solvent, dry them
thoroughly and in-
stall securely. Turn
the fuel valve “ON”
and check for leaks.
CDI
rype
’
’
Every
300
Hrs.
operating
0.9
-
1.0 mm
LO35
-
,039 in)
Use NGK BPJHS-IO or
BPR-4HS-iO
,
*
Check fuel tube for cracks or
’
leaks. Replace, if necessary.
1
encine dealer. The following adjustments should be performed by your Honda general purpose
ADJUST IGNITION TIMING ADJUST VALVE CLEARANCE ADJUST CARBURETOR SCREWS
*
Carburetor with pilot screw
Adjust contact breaker points
so
that they
*
Measure at TDC on comprcsslon stroke
*
Start the englne and adjust idle speed by
’)
Tighten
the
“IeW
it
just start
to
open, when
“F”
mark on whenengine is cold. turning the throttle
stop
screw.
flywheel aligns with the mark on crankcase.
*
STANDARD:
tightly, then back it off the number
of
turns
shown below:
*
IGNITION TIMING: 2O”BTDC. IN
0.05
-
0.1
1
mrn
(.0020
-
,0043
in)
EX 0.09
-
0.15
mm
(.0035
-
.0059
in)
G300
l/E
turns
G400
2
turns
*
If the clearance is less than the standard
2)
Adjust idle speed
as
outlined left.
~
limit, grind valve stem or replace valve.
-.
CYLINDER HEAD
GASKET
PILOT
SCREW
N VALVE
i
!,
CONTACT
BREAKER ASSY
The CDI type does not require adjustment.
I
i
’
A
throttle control cable (optional) may be used in
any
one
of
the
four
pull
directions shown.
Use
:I
either a
solid
core wire, or a flexible core wire with
4
a
return
spring and wire end.
j
THROTTLE CONTROL
Wire end
e
Flexible wire
core, mounting
BATTERY
t
Recommended battery
is
*Use only automobile
12V-32AH.
type vinyl covered wire
,fL,,/
effective diameter is (for
low
voltagej whose
&
(0.172
in) and which
utilizes press fit terminals
between the battery and
the engine. Length must
,/
7
+Protect the terminals
be within lm
(3
Ft).
with grease and com-
pletely cover the positive
cap. When connecting
terminal with
a
rubber
and negative leads are
terminals, ensure posltive
correctly connected.
a
j-
more than
4.4
mrn
*With electric starter
c
/
G300
I
G400
Cycle, valve arrangement
4
cycle, side valve
Displacement cc (cu
in)
1
272
(16.6)
1
406
(24.8)
Max. output hp/rpm
I
7/3,600
Max. torque kg-m (ft-lb)
I
1.5
(10.8)
2.3
116.6)
10/3,600
I
.,
Fuel consumption g/hp-h (lb/hp-h)
1
285 (0.62)
1
270 (0.59)
Starting system
25 (55.1)
1
33 (72.7)
Dry weight kg
(Ib)
Counterclockwise
PTO shaft rotation
D.C. starter motor
ALL INFORMATION, ILLUSTRATIONS, DIREC-
TIONS AND SPECIFICATIONS INCLUDED IN THIS
PUBLICATION ARE BASED ON THE LATEST
PRODUCT INFORMATION AVAILABLE AT THE
TIME
OF
APPROVAL FOR PRINTING. HONDA
MOTOR CO., LTD. RESERVES THE RIGHT TO
MAKE CHANGES AT ANY TIME WITHOUT NOTICE
AND WITHOUT INCURRING ANY OBLIGATION
WHATEVER.
NO PART
OF
THIS PUBLICA4TION MAY BE RE-
PRODUCED WITHOUT WRITTEN PERMISSION.
HONDA
HONDA
MOTOR
CO.,
LTD.
TOKYO.
JAPAN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Honda Honda Engines G400 Electric Start Owner's manual

Honda
Brand
Honda
Model
Honda Engines G400 Electric Start
Category
Engine
Type
Owner's manual
This manual is also suitable for

Honda Honda Engines G400 Electric Start is a reliable and powerful engine that is perfect for a variety of applications. With its 10 horsepower and 2.3 kg-m of torque, it can easily handle even the toughest tasks. The electric starter makes it easy to get started, and the counterclockwise PTO shaft rotation provides versatility for a variety of attachments.

The G400 is also fuel-efficient, consuming only 270 g/hp-h (0.59 lb/hp-h). This makes it an economical choice for long-term use. And with its dry weight of only 33 kg (72.7 lb), it is easy to transport and maneuver.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents