Transcension UP-2 Uni Pack 2 User manual

Brand
Transcension
Model
UP-2 Uni Pack 2
Category
Stroboscopes & disco lights
Type
User manual
UP-2 Uni Pack 2
Order code: BOTE32
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
1
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power
supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g. short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
2
Overview:
1, Output 10A Max.
2, Segment display Shows current activity or function.
3, Menu button Press to enter next function
4, Up Button Each press will increase the value once.
Pressing and holding down the buttons will increase the
settings quickly.
5, Down Buton Each press will decrease the value once.
Pressing and holding down the buttons will decrease the
settings quickly.
6, LTP slider This slider adjusts channel output intensity and complies with LTP
principle (Latest take precedence)
7, Fuse F10A 250V 5 x 20mm
8, DMX In 3-Pin XLR male socket, used to receive DMX data
9, DMX Out 3-Pin XLR female socket, used to send DMX data
3
Operating instructions:
DMX Address Mode
Switch Pack Mode
4
A123
1, The display shows the DMX address
of the current setting e.g. “123”.
A125
2, Each press of the “UP or “DOWN” buttons will change
the DMX address one by one. Pressing and holding
down the buttons will change the DMX address quickly.
Once the DMX address is set, it will be stored
into the memory automatically.
Note: During DMX addressing, the output is disabled.
A---
1, When the DMX address is complete, press the
“MENU” button to enter the next function.
s---
2, Press the “UP” or “DOWN” buttons until the
display shows “S---”.
5
Operating instructions:
Switch Pack Mode (cont..)
S-o n
3, Press the ”MENU” button to enter Switch Pack Mode.
The Switch Pack Mode consists of Switch On (S-on) and
Switch Off (S-of).
In the Switch On mode, output is turned on and the xture
lights regardless of DMX signal
In the Switch Off mode, output is turned off and the xture is
controlled by DMX signal. When the DMX level is less than
40%, the xture goes off and when the DMX level exceeds
40% the xture is on.
A-o f
4, Press the “UP” or “DOWN” buttons to swap between Switch
On and Switch Off modes.
A 1 2 5
5, Once the Switch Pack is selected , press the ”MENU” button
to return to the DMX address mode.
6
Operating instructions:
Dimmer Pack Mode
A125
1, Press the “MENU” button to enter the next function.
L888
2, Press the “MENU” button to enter the Dimmer Limit mode.
L888
3, Press the “UP: or “DOWN buttons to change the value
within the range of 10-100. Each press will change the
value once and holding down the buttons will change the
value quickly.
Once the Dimmer Limit is selected, it will be stored
automatically.
p888
4, Press the “MENU” button to enter DIMMER Preset mode.
p888
6. Press the “MENU” button to return to the DMX address
mode.
Operating instructions:
Dimmer Pack Mode (Cont...)
Technical Specications
Power supply: 240v
Channel Output: 10A Max.
DMX In: 3-Pin XLR male
DMX Out: 3-Pin XLR female
Fuse: F10A 250v 5 x 20mm
Dimensions: 182 x 92 x 65mm
Weight: 1.1Kgs
A125
5, Press the “UP: or “DOWN buttons to change the value
within the range of 10-100. Each press will change the
value once and holding down the buttons will change the
value quickly.
Once the Dimmer Preset is selected, it will be stored
automatically.
7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Transcension UP-2 Uni Pack 2 User manual

Brand
Transcension
Model
UP-2 Uni Pack 2
Category
Stroboscopes & disco lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents