York YVF/YVS User manual

Brand: York

Model: YVF/YVS

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

York YVF/YVS is a fan coil air conditioner designed for vertical installation in concealed, cabinet, or recessed wall models. These units are often used for perimeter heating and cooling of various buildings, including offices, corridors, hospitals, apartments, hotels, and other multi-room structures.

Key Features:

Versatile Mounting Options: Concealed (YVC), cabinet (YVF/YVS), or recessed wall (YWC) models to suit different installation requirements.
Heating and Cooling: Provides both heating and cooling functionality, making it suitable for year-round comfort.
Water Coil: Utilizes a hydronic coil for efficient heat transfer, compatible with hot or chilled water systems.

Key Features:

Versatile Mounting Options: Concealed (YVC), cabinet (YVF/YVS), or recessed wall (YWC) models to suit different installation requirements.
Heating and Cooling: Provides both heating and cooling functionality, making it suitable for year-round comfort.
Water Coil: Utilizes a hydronic coil for efficient heat transfer, compatible with hot or chilled water systems.

INSTALLATION, OPERATION, & MAINTENANCE

FAN COIL

AIR CONDITIONERS

Supersedes: Form 115.20-NOM3 (105) Form 115.20-NOM3 (1006)

***** WARNING TO INSTALLER, SERVICE PERSONNEL AND OWNER *****

Altering the product or replacing parts with non authorized factory parts voids all warranty or

implied warranty and may result in adverse operational performance and/or a possible hazardous

safety condition to service personnel and occupants. Company employees and/or contractors are

not authorized to waive this warning.

Notes:

1. 2-Pipe units have one water coil. 4-Pipe units have two water coils.

2. Changeover is used to select heating or cooling mode.

3. YORK International does not recommend “fan cycle” applications for cooling on unit mounted thermostats.

4. For proper operation, control valve must be normally closed.

5. Aquastats provided where required.

MODEL YVC -Vertical Concealed Model

The YVC model fan coil is designed to be furred into the

wall where the supply and return or both are connected

to short runs of ductwork. These units are often used

for perimeter heating and cooling of ofﬁces, corridors,

hospitals, apartments, hotels, and other multi-room

buildings.

MODEL YVS I YVF -Vertical Cabinet Models YVS

(Slant Top), YVF (Flat Top)

The YVS I YVF model fan coils have the addition of an

attractive, painted cabinet to blend with any decor. These

units will have heavy-duty stamped face louvered grilles

(Style A), plastic discharge grilles (Style A), or metal

grilles (Style B). These units are typically installed in

plain sight, under windows or against walls in schools,

hospitals, ofﬁce buildings, and other institutions.

MODEL YWC -Vertical Recessed Wall Model

The YWC model fan coil is designed to be recessed

into the wall. These units are engineered to be quiet and

designed to be easy to install and service. These units

are ideal for perimeter heating and cooling in hotels,

apartments, hospitals, public ofﬁce buildings, ofﬁces,

corridors, and other multi-room buildings. This unit

comes standard with a decorative wall panel for front

supply and return air.

00563VIPa

00803VIPa

YVC

YVF/YVS

YWC

00771VIPa

L23953Y 1006

YORK INTERNATIONAL

FORM 115.20-NOM3 (1006)

TABLE OF CONTENTS

FIG. 1 – VERTICAL UNITS ONLY - YVC, YWC, YVF, YVS AIR FLOW

Reference Documents:

• IOM for YH (Horizontal Units) Form 115.20-NOM3 (Latest)

• IOM for YSHW, YSHX Form115.22-NOM5 (Latest)

• IOM for YSVW, YSVX Form 115.22-NOM2(Latest)

• Parts List Form 115.20-RP2(Latest)

These documents can be ordered through Publications Dept.

or downloaded @ http://intranet.york.com/web0003/library/default.asp

LDO6704

INSTALLATION

...............................................................................................................................................

3-10

RECEIVING

...................................................................................................................................................

STORAGE

.....................................................................................................................................................

PREPARE WALL FOR MOUNTING

..............................................................................................................

WIRING

..........................................................................................................................................................

PIPING

...........................................................................................................................................................

STARTUP CHECKLIST

.....................................................................................................................................

MAINTENANCE

.................................................................................................................................................

12 - - - -YVC 126 31 R YPP* N1

CFM (100'S)

3,4,6,8,10,12 CONTROL OPTIONS

VALVE PACKAGE

COIL CONNECTIONS

R - Right Hand

L - Left Hand

COIL TYPE

3 - 3 Row

4 - 4 Row

31 - 3 Row Cool, 1 Row Heat

41 - 4 Row Cool, 1 Row Heat

UNIT STYLE

YVC - Concealed

YVF - Cabinet Flat Top

YVS - Cabinet Slope Top

YWC - Recessed Wall

UNIT VOLTAGE

126 - 120V - 1PH - 60Hz

246 - 208/240V - 1PH - 60Hz

225 - 220V - 1PH - 50Hz

277 - 277V - 1PH - 60Hz

YORK INTERNATIONAL

INSTALLATION

FORM 115.20-NOM3 (1006)

RECEIVING

Material in this shipment has been inspected at the

factory and released to the transportation agency in

good condition. When received, a visual inspection of

all cartons should be made immediately. Any evidence

of rough handling or apparent damage should be noted

on the delivery receipt and the material inspected in the

presence of the carrier's representative.

If damage is found, a claim should be

ﬁled against the carrier immediately.

STORAGE

If the equipment is not to be immediately installed, store

it in a dry location with the motor protected against

moisture, dust, corrosion and physical damage.

PREPARE WALL FOR MOUNTING

Depending upon building construction, provisions

for mounting the unit must be made by the contractor

according to architects; drawings.

Unit must not be operated during

building construction due to excessive

airborne dust and debris. The units

must not be operated under any cir-

cumstances without an air ﬁlter in

place.

It is recommended that all mounting

holes be used for proper installation.

YVS / YVF UNIT STYLE (VERTICAL CABINET)

See Fig 7 for unit details and dimensions.

Mounting location must allow enough clearance to

permit the removal of screws that secure the cabinet

panels. After selecting the location for the unit, remove

the front panel. The front panel must be removed on

the YVS or YVF unit to gain access to the coil, drain

connections and electrical junction box. To accomplish

this:

1. Pull ﬁrmly on the lower cabinet door (each side)

until the cabinet releases from its friction fastener.

2. Proceed to lift the door assembly straight up and

off the cabinet frame.

YVC UNIT STYLE ( VERTICAL CONCEALED)

See Fig 8 for unit details and dimensions.

Mounting location must allow enough clearance to

permit the removal of screws that secure the cabinet

panels. After selecting the location for the unit:

1. Remove the front panel.

2. Position the unit in its permanent location, making

sure it is level to insure proper drainage and opera-

tion, and secure the unit in place.

3. Secure the unit to the wall using the four, 1/2 inch

holes provided (two on each end of the unit).

Access must be provided for servicing the unit. If this

access is provided by a removable panel, ample space

must be allowed for access to electrical and plumbing

controls.

YWC UNIT STYLE (RECESSED WALL)

See Fig 9 for unit details and dimensions.

Mounting location must allow enough clearance to

permit the removal of all mechanical parts within the

unit.

1. Frame the unit as required so the front panel of the

wall unit will be ﬂush with the drywall surface when

installed.

2. Frame around the perimeter of the unit as required

for securing the drywall. See Table 1 below for

drywall openings.

MODEL NUMBER DRYWALL CUTOUT DIM

HT x WD

3YWC 28 x 42

4YWC 28 x 50

6YWC 28 x 58

8YWC 28 x 66

10YWC 28 x 74

12YWC 28 x 82

TABLE 1 – DRYWALL OPENINGS

YORK INTERNATIONAL

FORM 115.20-NOM3 (1006)

INSTALLATION

WIRING

All wiring must comply with the local and national code

requirements. Units are provided with wiring diagrams

and nameplate data to provide information required for

necessary ﬁeld wiring.

For power wiring a control box is provided on the

cabinet for connection of power supply and is located

on the opposite side of piping.

Any devices such as fan switches or

thermostats that have been furnished

by the factory for ﬁeld installation

must be wired in strict accordance

with the wiring diagram that is sup-

plied with the unit. Failure to do so

could result in damage or injury.

V A L V E

L (L 1)

N (L 2)

P OW E R

S U P P L Y

G R D

T B 1-1 T B 1-2 T B 3-1 T B 3-2 T B 2-2 T B 2-4

T B 2-3 T B 1-4 T B 2-1

H E A T O F F C OO L

ME D

H E A T C O OL

L O

L 1

T B 3-3 T B 2-5

MO T O R

T B 1-1 T B 1-2 T B 3-1 T B 2-2

T B 3-2 T B 2-3 T B 2-4 T B 1-4 T B 2-1

T B 3-3

MO T O R

O F F

C OO L

ME D

HI LO

L(L1)

N (L2)

V AL V E

R IS E

AQ UAS T AT

P OW E R

S U P P LY

G R D

HE AT

T B 2-5

T HE R MIS T O R

(UNIT -MT D )

(O P T IO NAL )

FIG. 2 - MANUAL CHANGEOVER,

CONTINUOUS FAN, T420 THERMOSTAT.

NO AQUASTAT LOCKOUT

2-PIPE HEAT / COOL

FIG. 3 - AUTO CHANGEOVER,

CONTINUOUS FAN, T421 THERMOSTAT.

LDO6889

LDO6890

3. Mount the unit in its permanent location; making

sure it is level to insure proper drainage

and operation. 2 – ½” holes have been provided on

each end of the unit for securing the unit to the wall

studs.

4. After the drywall has been installed, recheck to

make sure the unit’s front panel is ﬂush with the

exterior drywall surface. Shimming of the unit

may be required to get a seal between the unit and

panel.

5. Install the wall panel to the front of the unit using the

¼-20 x 1-1/2” long, painted, Phillips head screws

(4 on unit sizes 3,4,6 and 8; 6 on unit sizes 10 and

12). ¼” cage nuts are located in the slotted front

panel of the unit.

6. Remove the lower return air grille to get access to

the ﬁlter.

YORK INTERNATIONAL

INSTALLATION

FORM 115.20-NOM3 (1006)

L (L1)

N (L2)

P OW E R

S U P P LY

G R D

T B 1-1 T B 1-2 T B 3-1 T B 3 -2 T B 2-2 T B 2-4

T B 2-3 T B 1-4 T B 2-1

HE AT O F F C OO L

ME D

HE AT C OO L

T B 3-3 T B 2-5

MO T O R

V AL V E S

T HE R MIS T O R

(UNIT -MT D )

T B 1-1 T B 1-2 T B 3-1 T B 2-2

T B 3-2 T B 2-3 T B 2-4 T B 1-4 T B 2-1

T B 3-3

O F F

C OO L

ME D

HI LO

HE AT

T B 2-5

L (L1)

N (L2)

P OW E R

S U P P LY

G R D

MO T O R

V AL V E S

FIG. 4 - MANUAL CHANGEOVER,

CONTINUOUS FAN, T420 THERMOSTAT. FIG. 5 - AUTO CHANGEOVER,

CONTINUOUS FAN, T421 THERMOSTAT.

4-PIPE HEAT / COOL

LDO6891 LDO6892

PIPING

These units employ a hydronic coil designed for use

with either hot or chilled water.

All piping must be adequately sized to meet the design

water ﬂow requirements as speciﬁed for the speciﬁc

installation. Piping must be installed in accordance with

all applicable codes.

PIPE SIZES

• Tubing connections are 5/8" OD on all models.

• Manual air vents are provided standard on all

coils.

• All chilled water piping must be insulated to prevent

condensation.

PRECAUTIONS

1. Flush all ﬁeld piping prior to connection to remove

all debris.

2. Use wet cotton rags to cool valve bodies when

soldering.

3. Open all valves (mid-way for hand valves, manually

open on motorized valves) prior to soldering.

4. When soldering to bronze or brass, heat the pip-

ing while in the socket/cup and begin introducing

the solder when the ﬂux boils rapidly. Avoid direct

ﬂame into the solder joint.

5. Heat can only be applied to the cup of the valve body

for a minimal time before damage occurs (even with

the use of wet rags).

Prior to connecting to the fan coil,

all external piping must be purged

of debris.

When connecting piping or valve

kits to fan coil units, do not bend or

reposition the coil header tubing for

alignment purposes. This could cause

a tubing fracture resulting in a water

leak when water pressure is applied

to the system.

YORK INTERNATIONAL

FORM 115.20-NOM3 (1006)

INSTALLATION

Many valve packages will not phys-

ically allow all components to fit

over an auxiliary drain pan. It is the

installers responsibility to ensure ad-

equate condensation prevention. The

installer must also ensure that there

is no condensate drippage onto elec-

trical components beneath insulated

components.

6. Avoid rapid quenching of solder joints, as this will

produce joints of inferior quality.

7. The valve package will not support the weight of

the connecting pipes. All pipes, which are connected

to the units, must be completely supported prior to

connection to the unit.

8. Provisions must be made for expansion and con-

traction of piping systems. All horizontal and

vertical risers, including runouts, must be able to

withstand signiﬁcant movement with temperature

changes. Failure to do so will result in damage and

failure of piping, ﬁttings and valves throughout the

building.

9. Never insulate the heads or motorized portion of

control valves. Damage can occur in the form of

excessive heat build up and interference to the

operation and moving parts will result.

10. All piping made in the ﬁeld should be installed with

consideration of additional space for any electrical

routing that may be required.

11. Hydronic systems are not designed to hold pres-

surized air and should only be tested with water.

After the system has been proven leak free, all lines and

valve control packages must be insulated as speciﬁed

on the building plans.

DRAIN PIPING

Drain line installation must adhere to all code requirements.

The plastic auxiliary drain pan is to be located under the

coil/valve connections supported by its mounting bracket.

Make sure drain pan is level for proper drainage.

The auxiliary drain pan connection is suitable to receive

a standard 3/4” PVC coupling or elbow. Route the

condensate line such that it will have adequate slope

from the pan to the drain. After condensate line has been

run, make sure plastic drain line from blower plate nipple

is routed to plastic auxiliary drain pan and plastic cap is

installed on other nipple on the blower plate.

Note the 1-1/2” x 4-I/2” indentation in the plastic drain pan

(see Figure 6). This area is provided for the supply and

return runouts if they are brought up from below the pan.

All piping must be well insulated to prevent sweating.

Remove or cover the secondary drain

pan before soldering the supply and

return coil connections as hot solder

or the torch ﬂame may damage the

pan.

00182VIP

FIG. 6 - DRAIN PAN

YORK INTERNATIONAL

INSTALLATION

FORM 115.20-NOM3 (1006)

FIG. 7 - FAN COIL UNITS - DIRECT DRIVE, MODEL YVS & YVF

19-3/8

CONTROL ACCESS

DOOR

RETURN AIR OPENING

8-1/8 8-1/8

1/2

1/2 DIA. MTG.

HOLES

2 EACH SIDE

5/16 DIA. MTG.

HOLES

2 EACH SIDE

OPTIONAL BACK FRESH AIR INTAKE

DAMPER AND INSECT SCREEN

(SEE DETAIL)

*DIMENSIONS MAY VARY FOR

UNITS WITH NONSTANDARD

VALVE PACKAGES

516

SECONDARY PLASTIC

DRAIN PAN 0.84 O.D.

FOR 3/4" PVC PIPE

UNIT SIZES 10 & 12

Have two openings 2" apart

centered on center line

2-1/2

1/2

YVS YVF

BACK

TOP

FRONT

END END

1/2" PERMANENT

FILTER REMOVABLE

THRU RETURN AIR

OPENING

PLASTIC DISCHARGE

GRILLE

LEFT HAND UNIT SHOWN

7-1/4*

5-1/8

9-1/4

2-3/8

3-3/4

4-1/2

7-7/8

9-1/4

3-3/4

27-5/8

4-1/2

7-7/8

GENERAL DIMENSIONS

SIZE MODEL 3 4 6 8 10 12

DIM "A" 43 51 59 67 75 83

COIL CONNECTION

COOLING HEATING

5/8" O.D.

SWEAT

5/8" O.D.

SWEAT

LDO10373

YORK INTERNATIONAL

FORM 115.20-NOM3 (1006)

INSTALLATION

FIG. 8 - FAN COIL UNITS - DIRECT DRIVE, MODEL YVC

UNIT SIZES 10 & 12

Have two openings 2" apart

centered on center line

2-1/2

1/2

*DIMENSIONS VARY FOR UNITS

WITH NON STANDARD VALVE

PACKAGES

ALL DIMENSIONS ARE IN INCHES

SUPPLY &

RETURN

WATER

CONNECTIONS

1/2 DIA. MTG

HOLES

2 EACH SIDE

SECONDARY

PLASTIC DRAIN

PAN 0.84 O.D.

FOR 3/4" PVC

PIPE

SUPPLY AIR OPENING

FRONT ACCESS PANEL

CONTROL BOX

RETURN AIR OPENING

(MTG. HOLES)

1/2" PERMANENT FILTER

REMOVABLE THRU

RETURN AIR OPENING

1" SUPPLY

DUCT

COLLAR

TOP

FRONT

END

1-7/8 1-7/8

7/8 7/8

7-1/4*

5-1/8

19-3/8

6-5/8

9-1/4

24-1/2

(RIGHT HAND UNIT SHOWN)

Hand of unit determined by

cooling coil connection when

facing the front of unit.

LDO10367

GENERAL DIMENSIONS IN INCHES

MODEL A B C D E

3 YVC 27-1/2 18 25-1/2 26-1/2 22-3/4

4 YVC 35-1/2 26 33-1/2 34-1/2 31-3/4

6 YVC 43-1/2 34 41-1/2 42-1/2 39-3/4

8 YVC 51-1/2 42 49-1/2 50-1/2 47-3/4

10 YVC 59-1/2 50 57-1/2 58-1/2 55-3/4

12 YVC 67-1/2 58 65-1/2 66-1/2 63-3/4

YORK INTERNATIONAL

INSTALLATION

FORM 115.20-NOM3 (1006)

FIG. 9 - FAN COIL UNIT DIMENSIONS - DIRECT DRIVE, MODEL YWC

LDO10324

GENERAL DIMENSIONS IN INCHES

MODEL A C D E COIL CONN SIZE

COOLING HEATING

3 YWC 27-1/2 25-1/2 26-1/2 22-3/4

5/8 O.D.

SWEAT

5/8 O.D.

SWEAT

4 YWC 35-1/2 33-1/2 34-1/2 31-3/4

6 YWC 43-1/2 41-1/2 42-1/2 39-3/4

8 YWC 51-1/2 49-1/2 50-1/2 47-3/4

10 YWC 59-1/2 57-1/2 58-1/2 55-3/4

12 YWC 67-1/2 65-1/2 66-1/2 63-3/4

22-3/8

*DIMENSIONS VARY FOR UNITS

WITH NON STANDARD VALVE

PACKAGES

ALL DIMENSIONS ARE IN INCHES

SUPPLY &

RETURN

WATER

CONNECTIONS

1/2 DIA. MTG

HOLES

2 EACH SIDE

SECONDARY

PLASTIC DRAIN

PAN 0.84 O.D.

FOR 3/4" PVC

PIPE

CONTROL BOX

RETURN AIR OPENING

(MTG. HOLES)

1/2" PERMANENT FILTER

REMOVABLE THRU

RETURN AIR OPENING

TOP

FRONT

(RIGHT HAND UNIT SHOWN)

Hand of unit determined by

cooling coil connection when

facing the front of unit.

END

1-7/8

7/8

7-1/4*

5-1/8

6-5/8

5-1/4

24-1/2

YORK INTERNATIONAL

FORM 115.20-NOM3 (1006)

INSTALLATION

SUPPLY &

RETURN

WATER

CONNECTIONS

1/2 DIA. MTG

HOLES

2 EACH SIDE

WIDTH

HEIGHT

RETURN AIR OPENING

(RIGHT HAND UNIT SHOWN)(RIGHT HAND UNIT SHOWN)

MODEL DRYWALL CUTOUT DIMENSIONS

MODEL HEIGHT WIDTH MINIMUM HEIGHT

ABOVE FLOOR (A)

3YWC 28" 42" 6"

4YWC 28 50" 6"

6YWC 28 58" 6"

8YWC 28 68" 6"

10YWC 28 74" 6"

12YWC 28 82" 6"

FIG. 10 - YWC FAN COIL INSTALLATION LOCATION DIMENSIONS

YORK INTERNATIONAL

INSTALLATION

FORM 115.20-NOM3 (1006)

FAN COILS START - UP CHECKLIST

Fan INSPECTION -

The fan should be inspected and cleaned, in conjunction with maintenance of the motor and bearings. It is

important to keep the wheel clean in order to avoid imbalance and vibration.

❑ Check tightness of fan bearing locking collar.

❑ With power off, check blower wheel set screws for tightness and ensure that the blower wheel(s) rotate freely and quietly.

❑ Check tightness of all motor base and mounting bolts.

❑ Check motor connections to ensure that they are secure and made in accordance with the wiring diagram

❑ Rotate all moving components manually. Adjust as required.

❑ Installer has cleaned out interior.

❑ Ensure drain pan free from foreign material.

❑ Ensure air ﬁlters are clean, installed properly and secured. Use the directional arrows or other information on the ﬁlter to

determine the proper ﬂow direction.

INSTALL CHECKLIST

❑ Equipment received as ordered.

❑ Unit checked for damage interior and exterior.

❑ Make sure all ductwork is complete and available for full air ﬂow.

❑ Unit installed level to ensure proper drainage and operation.

❑ Unit installed with proper clearances.

❑ Ensure condensate water will drain toward the drain connection. An overﬂow drain may be required as a back up to a clogged

primary drain.

❑ Check that coil(s), valves and piping have been leak checked and insulated as required.

❑ Main coil drain pan must be properly trapped and charged with water before units are started.

❑ Ensure that all air has been vented from the system.

❑ Return valves to their proper operating positions prior to start-up.

❑ Repair any solder joint leaks and gently tighten any leaking valve packing nuts and piping accessories as required.

❑ Install all panels.

NOTE: If the m

monthly to prevent moisture from accumulating in the bearings. (See Form 50.20-NM3, Long Term Storage)

CLEANING CHECKLIST

CONTROLS CHECKLIST

❑ Check that supply voltage matches nameplate data.

❑ Ensure that the unit is properly grounded.

❑ Controls installation complete

❑ Check all electrical connections for tightness.

❑ Review electrical print for correct wiring.

MAINTENANCE

MOTOR

The blower motor should be cleaned annually and if it

has oiling ports, it should be oiled with a good grade of

SAE 20 oil. Normally a few drops of oil in each bearing

is sufﬁcient.

If motor service is required, it can be removed in the

following manner:

1. Disconnect electrical power to the unit at the discon-

nect switch and lock out.

2. Remove two screws, securing blower deck to unit.

3. Locate motor lead wires where they connect to the

side panel, (lower rear on the electrical box side).

4. The quick connect plug needs to be squeezed on top

and bottom to release it from its socket (dual motor

units have two plugs).

5. Now slide blower / motor deck out of unit to ser-

vice.

6. Reverse process to install.

COIL

The coil must be kept clean by any of the following

methods.

1. Cleaning with low-pressure compressed air.

2. Flushing or rinsing with water (a detergent is ad-

visable for greasy surfaces).

3. Prior to the water system start-up and balancing, the

chilled/hot water systems should be ﬂushed to clean

out dirt and debris, which may have accumulated

during construction. All unit service valves are to

be closed during this process. Strainers are to be

installed in the piping mains to prevent this material

from entering the units during normal operation.

FILTERS

Clean or Replace Air Filters Regu-

larly

The intervals at which filters require replacement

depend on local conditions.

Because of dust and lint in the room, room-air ﬁlters load

up much more rapidly than outdoor-air ﬁlters. Under

normal conditions, the room air ﬁlter requires cleaning

every six to eight weeks.

The ﬁlter is a permanent type and may be removed and

washed with a garden hose. Filter should be completely

dry before reinstalling. To remove the ﬁlter, rotate the

retaining rod holding the front edge of the ﬁlter so it

can drop below the front panel of the cabinet, then pull

outward to remove. To reinstall the ﬁlter, slide the ﬁlter

into the ﬁlter channels on both sides of the unit. Rotate

ﬁlter retaining rod on lower front edge of cabinet door

so that it is under the ﬁlter, then push the rod upward

into the cabinet door.

To ensure proper maintenance of the ﬁlters, it is best

to follow an organized maintenance procedure. The

following one is recommended:

Divide the total number of units on the job into six

equal groups. Each week inspect, clean or replace the

ﬁlters in each group, in rotation. This insures a uniform

servicing interval. The interval may be lengthened or

shortened as determined by experience. If inspection

shows only the room-air ﬁlter to be dirty, this one alone

should be replaced.

Dirty ﬁlters reduce the air and heating

capacities of the Unit. When the ﬁlters

are excessively dirty, the unit heating

capacity will be so reduced that it is in-

effective for heating the room. When

a room fails to heat, always check the

ﬁlters.

CLEAN UNIT INTERIOR

Once a year clean the fans and coils of the unit

thoroughly. Remove the access panel as necessary.

Wipe the interior of the unit clean with a rag. Wipe the

motor and inside and outside of the fan housings. (In

cooling units, clean out the drain pan.)

Tele. 800-861-1001

www.York.com

P.O. Box 1592, York, Pennsylvania USA 17405-1592 Subject to change without notice. Printed in USA

Form 115.20-NOM3 (1006)

Supersedes: Form 115.20-NOM3 (105)

York YVF/YVS User manual

Brand: York

Model: YVF/YVS

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

Key Features:

Versatile Mounting Options: Concealed (YVC), cabinet (YVF/YVS), or recessed wall (YWC) models to suit different installation requirements.
Heating and Cooling: Provides both heating and cooling functionality, making it suitable for year-round comfort.
Water Coil: Utilizes a hydronic coil for efficient heat transfer, compatible with hot or chilled water systems.

Download PDF

report

York YVF/YVS User manual

This manual is also suitable for

York YVF/YVS User manual

Related papers

Other documents