Page is loading ...
BF-22377 HAMPTON BAY COLLECTION 7 DRAWER CHEST
Home Decorators
ASSEMBLY INSTRUCTIONS
Made In China
Collection
LEFT
DRAWER PANEL SIDE-7PCS
RIGHT
FEET-4PCS
DRAWER PANEL BACK-7PCSDRAWER PANEL BOTTOM-7PCS
DRAWER PANEL SIDE-7PCS
DRAWER PANEL FRONT-7PCS
BOTTOM PANEL-1PC
I
L
J
K
part needed.
and hardware to the provided list to be sure all parts are present.
inside the carton during shipment.Once uppacked,compare all parts
Thank you for purchasing this quality product.Be sure to check all
provide your order number,item number and part number/letter of the
or fax our Custormer service Department.For speady service,please
If any parts or hardware are missing or damaged,please phone,e-mail
packaging material carefully for small parts,which may have loose
CB
PARTS LIST
TOP PANEL-1PC
E
A
D
LEFT SIDE PANEL-1PC
numbered to assure fast,easy and correct assembly.
Follow instructions listed below in proper sequence as
G
H
BACK PANEL-1PC
F
RIGHT SIDE PANEL-1PC
ACROSS PANEL-6PCS
IMPORTANT NOTE:
RIGHT OUTER SLIDER-7PCS
LEFT OUTER SLIDER-7PCS
RIGHT INNER SLIDER-7PCS
LEFT INNER SLIDER-7PCS
SCREWS-7PCS
SCREWS-56PCS
T
R
S
U
V
Y
W
KNOBS-7PCS
X
M
P
O
N
CAM-BOLTS-20CS
Q
CAM-TOOL-1PC
SCREWS-98PCS
SCREWS-28PCS
THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
NOTE:
TO PREVENT DAMAGE DURING ASSEMBLY,PLEASE ASSEMBLE THIS ITEM WITH AT
HOW TO USE THE CAM-TOOL
ARROW
ARROW
SHOULDER
LEAST TWO PEOPLE.
TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
NOTE:
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT.IN ORDER
UPON OPENING THOROUGHLY CLEAN ALL WOODS SURFACES TO REMOVE DUST
NOTE:
ATTACH THE DRAWER PANEL SIDE(H/I)TO DRAWER PANEL FRONT(G)USING SCREWS(Q).
INSERT DRAWER PANEL BOTTOM(J)INTO SLOT IN DRAWER PANEL SIDE(H/I).
ATTACH RIGHT/LEFT INNER SLIDE(W/V)TO DRAWER PANEL SIDE(H/I)USING SCREWS(U).
ATTACH DRAWER PANEL BACK(K)TO DRAWER PANEL SIDE USING SCREWS(H/I).
ROTATE THE 4 FEET(L)INTO HOLES IN BOTTOM PANEL(B).
2).ASSEMBLE THE FEET(L)
B
ATTACH THE KNOB(M)TO DRAWER PANEL FRONT(G)USING SCREWS(N).
1).ASSEMBLE THE DRAWER.
L
U
V
INSERT THE 12 DOWELS(R)INTO HOLES IN ACROSS PANEL(E).
ROTATE THE CAM-BOLTS(O)INTO HOLES IN SIDE PANEL(C/D).
ASSEMBLE THE ACROSS PANEL(E)
PLACE THE CAM-BOLTS(O)INTO HOLES IN PANEL(E)AND ATTACH USING CAM-LOCKS(P).
O
E
R
P
E
E
E
E
E
D
ROTATE THE 4 CAM-BOLTS(O)INTO HOLES IN BOTTOM PANEL(B).
ASSEMBLE BOTTOM PANEL(B)
P
B
O
PLACE THE CAM-BOLTS(O)INTO HOLES IN PANEL(C/D)ATTACH USING 4 CAM-LOCKS(P).
ROTATE THE 4 CAM-BOLTS(O)INTO HOLES IN TOP PANEL(A).
5).ASSEMBLE THE TOP PANEL(A).
ATTACH 14 RIGHT&LEFT OUTER SLIDE(Y/X)TO PANEL(C/D)USING SCREWS(U).
Y
X
O
P
U
PUSH THE 7 DRAWER IN TO SLIDE-OUTS.
ASSEMBLE THE DRAWERS
ASSEMBLE THE BACK PANEL(F)
ATTACH BACK PANEL(F)USING SCREWS(S).
S
F
/
