LG LD-1481S4 User manual

Brand: LG

Model: LD-1481S4

Category: Dishwashers

Type: User manual

This manual is also suitable for

OWNER’S MANUAL

WASHING MACHINE

WM0642H*

P/NO : MFL31245123

www.lg.com

Please read this manual carefully before operating

your set and retain it for future reference.

DISHWA SHER

OWNER'S MANUAL

Before beginning installation, read these instructions carefully.

This will simplify installation and ensure that the dishwasher is installed

correctly and safely. Leave these instructions near the dishwasher

after installation for future reference.

LD-1481*4

MFL68741410

CONTENTS ................................

IMPORTANT SAFETY

INSTRUCTIONS

Important safety instructions ..............3

Read all instructions before use ........4

Save these instructions ......................5

INSTALLATION INSTRUCTIONS

Prepare the installation opening .......7

Preparation for electrical wiring ........7

Preparing the dishwasher for

Installation ..........................................8

Installing the dishwasher in

its location .......................................... 8

Installation of drain hose ....................9

Installation of water inlet hose .........10

Final check and assembling ............10

How to level the dishwasher ............ 10

PARTS IDENTIFICATION ........

FUNCTION OF CONTROL

BUTTONS ................................

BEFORE USING FOR THE

FIRST TIME

Checking your water hardness level

..... 14

Setting up the softening system level

(hardness level) of your dishwasher

......15

Salt lling .........................................16

Adding rinse aid ............................... 17

INFORMATION FOR ENERGY

TEST ........................................

HOW TO USE AND OPERATE

Daily use load ..................................19

Cutlery basket ..................................20

Lower rack .......................................21

Upper rack .......................................21

Adding detergent .............................22

Relling ............................................ 24

Select the programme .....................25

Drying ..............................................26

OPERATING SEQUENCE ......

USER MAINTENANCE &

CLEANING INSTRUCTIONS

Not used for a long time ...................28

Cleaning the inside .........................28

Clean using white vinegar ...............28

Filters ............................................... 29

Upper spray arm .............................. 30

Lower spray arm .............................. 31

TROUBLE SHOOTING GUIDE

Display code (condition code) ..........32

Display code (error code) ................34

Washing problems ...........................35

Noise problems ................................37

General problems ............................38

Using SMARTDIAGNOSIS ..............40

SPECIFICATION .....................

CONTENTS

Thank you for buying an LG Dishwasher.

Please read your owner’s manual

carefully, it provides instruction on safe

installation, use and maintenance.

Retain it for future reference.

Record the model and serial number of

your Dishwasher.

Model No.

Serial No.

Date of Purchase

For your safety, the information in this manual must be followed to minimize the risk of fire or

explosion, electric shock, or to prevent property damage, injury to persons, or death.

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION

BEFORE USE

WARNING

Death or serious injury can occur if the instructions are not strictly followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance.

Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can cause death or serious injury.

All safety messages will follow the safety alert symbol and either the word DANGER,

WARNING or CAUTION.

These words mean:

WARNING

You may be injured or cause damage to the product,if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance

of injury, and tell you what can happen if the instructions are not followed.

CAUTION

Death or serious injury will occur if the instructions are not strictly followed.

DANGER

IMPORTANT SAFETY INSTRUCTIONS

• Please read this manual carefully

before using the dishwasher for the

first time.

• This manual contains very important

notes regarding the installation, use and

maintenance of your dishwasher.

• The manufacturer can not be responsible

for problems caused by ignoring these

safety and caution instructions.

• This dishwasher is designed for normal

indoor, domestic household use.

• Do not use the dishwasher for

industrial or commercial use, or for

anything other than domestic use.

• The appliance is not intended for use

by young children or infirm persons

without supervision.

• Check packaging and the dishwasher

immediately for signs of transport

damage. If the appliance is damaged,

do not put it into use but contact your

supplier without delay.

• This appliance is intended to be used in

household and similar applications such

as;

- Staff kitchen areas in offices and other

non retail food working environments;

- By clients in holiday appartments and

other residential type environments;

• If this product is used for commercial or

mobile purposes, it is not warranted.

(Example: Public places such as

restaurants, eateries or cafes, boats,

mobile homes and caravans.)

If the product is installed outside

the normal service area, any cost of

transportation involved in the repair of the

product, or the replacement of a defective

part, shall be borne by the owner.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before use

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the dishwasher,

follow basic precautions, including the following:

• Electrical connection must be in

accordance with the rating label.

• Electrical safety is only guaranteed

when the earth system of your house

is in accordance with the related local

regulations. (Do not use an extension

cable or cord unless suited and

approved by Australian Standards.)

• If the hot water exceeds 65ºC, adjust

the water heater setting. If the hot water

temperature can not be maintained below

65ºC, the dishwasher must be connected

to cold water.

• If power supply cord is damaged, it must

only be replaced by the manufacturer

or its service agent or a similar qualified

person in order to avoid a hazard.

• This appliance must be positioned so

that the electrical plug and water supply

connection tap is accessible.

• The appliance is to be connected to water

mains within allowable pressures, and

connected with the supplied hose and that

old hose-sets should not be reused.

During installation

• Only suitable household utensils

should be placed in the dishwasher.

(Please avoid utensils; that are non-

heat-resistant, metal decorated, etc.)

During use

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before use

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the dishwasher,

follow basic precautions, including the following:

• Do not use any kinds of solvent in your

dishwasher. They may cause an

explosion or fire.

• Do not spray water on the appliance.

It may cause the failure of electric parts

or electric shock.

• Do not push down or sit on the door

when the door is opened. It may cause

damage or failure of your dishwasher.

• Do not use the detergent for hand

washing.

Dishwasher detergent should be used

for normal operation.

• This appliance is fitted with a safety

function that automatically stops the

operation of the dishwasher when it is

exposed to abnormal electrical disturbance

on its mains.

• Dishwasher detergents are extremely

alkaline.They can be extremely dangerous

if swallowed.

Avoid detergent contact with skin and

eyes and keep children away from the

dishwasher when the door is open.

Check that the detergent dispenser is

empty after completion of each wash

cycle.

• Controls may be locked using Child Lock

mode to prevent all the settings from being

changed by a child once the dishwasher is

in operation.

• For safety reasons, the Power button will

still be operative with the Child Lock

engaged.

• Keep children away from detergents

and rinse-aids.

• Do not allow children to operate the

dishwasher.

• Young children should be supervised

to ensure that they do not play with the

appliance.

Child Safety

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-grounding conductor and

grounding plug. The plug must be plugged into an appropriate outlet that is properly installed

and grounded in accordance with all local codes and standards.

• Do not use an adapter this will defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

Save these instructions

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

The instructions shall state the substance of the following :

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

CAUTION

CAUTION concerning the Power cord

• Most appliances recommend they be placed upon a dedicated circuit; that is, a single

outlet circuit which powers only that appliance and has no additional outlets or branch

circuits. Check the specification page of this owner's manual to be certain.

• Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,

extension cords, frayed power cords, or damaged or cracked wire insulation are

dangerous. Any of these conditions could result in an electric shock or fire.

• Periodically examine the cord of your appliance, and if its appearance indicates

damage or deterioration, unplug it, discontinue use of the appliance, and have the cord

replaced with an exact replacement part by an authorized servicer.

• Protect the power cord from physical or mechanical abuse, such as being twisted,

kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall

outlets, and the point where the cord exits the appliance.

If the appliance is connected to an extension cord or power board, they must be positioned

so that they are not subject to water splashing or ingress of moisture.

WARNING

Improper connection of the equipment-grounding conductor can result in electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether the

appliance is properly grounded. Do not modify the plug provided with the appliance - if it

does not fit the outlet, have a proper outlet installed by a qualified electrician.

•

A qualified electrician/plumber or competent person should carry out any electrical/

plumbing work required to install this appliance.

WARNING

1. This appliance must be supplied with the

correct and same voltage shown on

instruction manual, and connected to an

individual, properly earthed branch circuit,

protected by a minimum 15 amp circuit

breaker or time delay fuse.

Wiring must be 2 wires with Earth.

2. The power plug must be in a accessible

location adjacent to and not behind the

dishwasher and within 1.2 meters of the

dishwasher side.(See page 9 Fig.A)

3. The power plug must be correctly earthed, if

in doubt, have it checked by a qualified

Electrician. No other appliance should be

connected to the same plug outlet by a

double adapter or similar plug.

Dangerous voltage

To indicate hazards arising

from dangerous voltages.

Note- in case of an application

warning sign, the rules

according to ISO 3864 should

be adhered to.

1. This dishwasher is designed to fit the size

shown as below.

2. Select a location as close to the sink as

possible for ease of connection to the water

and drain pipes.

3. To ensure good drainage, the dishwasher

should not be installed more than 1 meter

away from the sink.

4. If the dishwasher is installed in a corner, a

minimum of 5cm of space is required

between the washer and an adjacent cabinet

or wall.

Unit:mm

INSTALLATION INSTRUCTIONS

•

For personal safety, remove house

fuse or open circuit breaker before

installation.

•

it is strongly recommended not use

an extension cord or adapter plug

with this appliance.

Electrical and earthing connections must

comply with the national electrical code/

provincial and municipal code and/or

other local codes and standards.

CAUTION

•

Any bare wood surrounding the

dishwasher should be sealed with a

waterproof paint or sealant to prevent it

from swelling.

CAUTION

Prepare the installation opening

Preparation for electrical wiring

•

If the height of the opening is below

850mm, you can remove the top table by

unscrewing the 2 screws.

(Two from rear)

CAUTION

1. Lay the dishwasher on its back.

2. Adjust the legs to the required height

as shown in below figure.

1. Before sliding the dishwasher into the

installation opening, all necessary height

and height adjustments should be made

using a spanner.

2. Slide the dishwasher into the cabinet,

opening carefully. Make sure that the drain

hose inside the cabinet is not kinked or

stretched.

Adjust leg

INSTALLATION INSTRUCTIONS

Preparing the dishwasher for

installation

Installing the dishwasher in its

location

(use an open end or adjustable spanner.)

27mm or

1-1/16 inch

1. If the end of drain hose does not fit to the

drain line, use a rubber coupling (not

supplied) that is resistant to heat and

detergent.

2. This should be available from a plumbing

shop or a hardware store.

3. There are two typical connections as shown

in Figure A, B.

The S trap spigot must be drilled out cleanly

and free of obstruction to its maximum

internal diameter, if used for drainage.

To prevent siphoning, one of the following

methods must be used:

Check the waste spigot when initially installing.

An “OE” error can occur when the waste spigot

below the sink is not drilled out properly.

Please ensure the waste spigot connection to this

drain hose has been completely drilled out before

connecting and securing.

Connection to Waste spigot

When the drain hose is connected to a sink S

trap or waste disposal unit, the hose must be

looped up to the underside of the bench top

and secured.

Drain hose Extension

Extend drain hose as shown below.

Drain hose

extension kit

Fig. A

When the drain hose is connected to a

separate standpipe, it is essential that an

airtight connection be made.

Refer to Fig.B

Fig. B : Drainage connection - stand pipe.

INSTALLATION INSTRUCTIONS

Installation of drain hose

•

When you connect or extend drain hose,

make sure that the drain hose is not

kinked.

(Bends should have a 40mm radius.)

CAUTION

Use the drain hose extension kit appropriately.

• This dishwasher may be fed with either hot or

cold water. If the water can not be maintained

below 65ºC, the dishwasher must be connected

to cold water.

• When connecting, you may use sealant tape or

sealing compound to avoid water leaks.

• Make sure that the line is not kinked or sharply

bent.

• It is recommended that the new inlet hose be

used and not an existing or old hose.

Final check and assembling

1. Securely hand tighten supply hose to the

water supply.

Plug the power supply cord into an earthed

electrical point and switch on after having

turned on the circuit breaker.

2. After installing and prior to using the

dishwasher with crockery, we recommend that

you use the dishwasher on Quick mode to

rinse through. At this stage it is useful to

ensure that there are no operating problems or

water leaks.

When the dishwasher is used for the first time,

there may be a loud noise, if this happens, turn

off the power and restart the dishwasher.

After installing the dishwasher, you may notice a

slight sticking of the door to the dishwasher,

when you open or close the door. If this does

happen you need to adjust the level of the

dishwasher.

• If the door slants to the right, see fig. C follow

these instructions:

1) Unscrew(counter-clockwise) the left leg of

the back side and correct the level.

2) Check the opening of door and repeat if

necessary until the door opens and closes

properly.

• When the product is correctly leveled, there

should be no slant, stickiness or rubbing sound.

Fig. C

Case 1. In case the door is slanted to the right

• If the door slants to the left, see fig. D follow

these instructions:

1) Check the opening of the door to hear if

there is a sticking or rubbing sound.

2) Check the opening of door and repeat if

necessary until the door opens and closes

properly.

• When the product is correctly leveled, there

should be no slant, stickiness or rubbing sound.

Fig. D

Case 2. In case the door is slanted to the left

Water tap

Fig. A

Fig. B

Some models consist of an inlet valve combined

with a hose. (Fig. A)

Connect the water supply hose to the water tap.

(Fig. B)

After connecting the inlet hose to the tap, turn on

the tap to flush out foreign substances (dirt, sand

or sawdust) in the water lines. Let water drain into

a bucket, and check the water temperature.

Connect the supply hose to the water inlet valve.

INSTALLATION INSTRUCTIONS

Installation of water inlet hose How to level the dishwasher

PARTS IDENTIFICATION

1. Control panel

2. Door handle

3. Front cover

4. Lower cover

5. Display window

6. Power button

7. Drain hose

8. Inlet hose

9. Power cord

10. Adjustable leg

11. Upper rack

12. Cutlery basket

13. Detergent and rinse aid dispenser

14. Vapor vent cover

15. Upper spray arm

16. Lower spray arm

17. Filter ASM

18. Lower rack

19. Salt container cap

※ The appearance and specifications may vary without notice.

Funnel

Accessory

FUNCTION OF CONTROL BUTTONS

①

NOTE

The Dishwasher can be used without salt if not required,

however, the hardness level will need to be set to H0 so

that the indicator does not remain lit. (See page 14.)

①

Process Indicator

• Indicates current program phase.

• The Wash, Rinse and Dry lamps will flash during each phase of washing process.

• The Clean lamp flashes for 4 minutes at the end of the cycle.

②

Salt & Rinse Refill Indicator

• Salt : Refill with special salt when the

Salt lamp

turns on.

• Rinse : Refill with rinse aid when the Rinse turns on.

③

Half Load

• In case of a small load, use upper or lower rack to save energy.

• With each press, you can select the Upper or Lower rack only.

• In case you don’t select this button, the machine always operates the vario washing, which operates the upper and lower

spray arm alternately.

④

Extra Hot & Child Lock Indicator

• Lamp will turn on when the Extra Hot setting is on.

• Lamp will turn on when the Child Lock setting is on.

⑤

Time Left

• Before starting, the display window shows the running time of the selected program(except for the Auto programme).

•  After starting, the display window shows the remaining time.

• If the dishwasher has a problem, the error type will be displayed. (OE, IE, AE(EI), FE, HE, tE, LE, nE)

• If these error letters are displayed, please refer to the trouble shooting on page 29 and follow the guide.

⑥

Delay Start

• If you want to delay the start of the selected program, press this button.

• Press this button to increase the starting time by 1 hour increasements.

• The delay start time can be adjusted from 1 hour to 19 hours.

⑦

Program

• Press the cycle that corresponds to your desired wash cycle.

⑧

Extra Hot

• If you select the Extra Hot function, the operating temperature will be up to 80ºC.

(Dual Intensity, Auto, Eco, Eco and Soft Spray)

Programme Default Spray

Rinse

(Extra Hot)

(Rinse

)

Half load

(Upper)

(Lower)

Spray Child Lock Delay Start

Quick Strong

◦ ◦

Quick & Dry Strong

◦ ◦ ◦

Eco Strong

◦ ◦ ◦ ◦ ◦

Auto Medium

◦ ◦ ◦ ◦

Steam Care Medium

◦ ◦ ◦ ◦ ◦

Steam

Dual Spray

Medium

◦ ◦ ◦ ◦ ◦

Steam Power Strong

◦ ◦ ◦

SMARTDIAGNOSIS

™

function is available only for

the products with a

SMARTDIAGNOSIS

™

mark.

(Refer to Page 40.)

⑦

②

③ ④ ⑥

⑪

⑤ ⑨

⑧ ⑫⑩

• To engage the Extra Hot rinse in the allowable cycles, hold down the Dual Intensity & Auto buttons simultaneously.

⑨

Beep On/Off

• The dishwasher must be switched on.

• The beep on/off function can be engaged or disengaged by pressing the Delay Start and Quick & Dry buttons

simultaneously for a few seconds.

⑩

Eco and Soft Spray

• If you want to use Eco and Soft Spray course, press & hold Eco button for 3 seconds.

⑪

Child Lock

• Used to lock or unlock the control buttons to prevent all the setting from being changed by a child after starting the wash

cycle.

• To activate or release the Child Lock function, press the Quick & Dry and Quick buttons simultaneously for a few

seconds while the dishwasher is in operation.

• All controls will be disabled except the Child Lock and Power buttons.

• Turning off the dishwasher will not reset the Child Lock function. You must release the Child Lock before you can

operate the dishwasher. The Child Lock function cannot be engaged whilst the unit is in the off (stand by) mode.

⑫

Power

• For operating, press this button first for power on.

• After the programme has completed, this button automatically switches off for safety and energy saving.

• The unit will automatically turn off if the programme is interrupted and not resumed, or started within 4 minutes.

• In case of mild power surges to the machine, the power may be automatically turned off for safety.

•

To turn the power off during a programme, press the

Power

button twice.

Programme Default Spray Extra Hot

Half load

(Upper) (Lower)

Child Lock Delay Start

Quick Strong

◦ ◦ ◦

Eco Strong

◦ ◦ ◦ ◦

Eco Plus -

◦ ◦ ◦ ◦

Auto -

◦ ◦ ◦ ◦

Quick & Dry Strong

◦ ◦

Dual Intensity Medium

◦ ◦ ◦ ◦

■

Method 1

- Check the water hardness in your area.

(Your water supply management agency can help you with this.)

■

Method 2

- You can check water harness by using test kit included in the product.

① Immerse the test strip for 30 seconds (Not in running water!)

② Shake off liquid from the test kit, and then wait for 1 minute for checking the change of color.

③ Check the setting value applicable to the number of changed colors.

Step 1. Checking your water hardness level

< Water hardness level >

Hardness setting

BEFORE USING FOR THE FIRST TIME

In order to provide satisfactory rinsing results, the dishwasher requires soft water, i.e., containing

little or no lime, otherwise water stains will be left behind on the dishes and interior containers.

If the tap water exceeds a certain level of hardness, it must be softened, i.e., decalcified.

This is achieved by adding a special salt to the water softener inside the dishwasher.

The required amount of salt is set up according to how hard your tap water is.

This model has a water softener to soften hard water.

Please read these notes carefully for correct operation.

Before test Under test After test

* 2 areas changed

1 °e = 14.25 mg/l CaCO

f = 10 mg/l CaCO

d = 10 mg/l CaO (=1,78

f) (=1,25 °e)

Number of

the areas

(red-violet)

Hardness range

Water

quality

Softening

system

level

ºd ºe ºf

mmol/l

(Ca+Mg)

mg/l

<4 <5 <7 <0.7 <29

soft

very hard

4 -7 5 - 9 7 - 13 0.7 - 1.3 29 - 50 H1, H2

7 - 14 9 - 17.5 13 - 25 1.3 - 2.5 50 - 100 H3, H4

14 - 21 17.5 - 26 25 - 38 2.5 - 3.8 100 - 150 H5, H6

>21 >26 >38 >3.8 >150 H7

Step 2. Setting up the softening system level (hardness level)

of your dishwasher

BEFORE USING FOR THE FIRST TIME

For effective washing performance, adjust the setting corresponding to the hardness level of water

used in water supply. The water softener has 8 adjustment levels, and the dishwasher is programmed

at the factory for a water hardness level of H00. You can check the default setting value and adjust it

in the following manner:

1. Press Half Load

and Power button

simultaneously.

(Current setting value

indicated.)

2. Press the Half Load

button, and then set

up your intended

value.

(Scope of setting

value : H00~H07)

3. Press the Delay Start

button for saving the

setting.

(The power turns off

upon the saving.)

* The display may vary, depending on the model.

• The ‘Salt Filling’ light turns on in the display if salt is not in the softening system.

• If the hardness setting is set to H0, no light turns on in case of no salt.

NOTE

BEFORE USING FOR THE FIRST TIME

•

Do not pour any detergent in the water softener. It may cause a malfunction.

WARNING

Step 3. Salt Filling (Hard water requires salt filling)

Salt

Water

Salt filling must be made before starting the washing program. In case of insufficient salt, the ‘Salt

Filling’ light turns on in the display, unless the Hardness level has been set to H0. (refer to page 15)

1) Remove the lower rack and remove the cap of the water

softener placed in the left side of the bottom of the

washing part by rotating it counterclockwise.

2) Before using your dishwasher for the rst time, it is

necessary to Pour 1.5kg of salt and 1 litre of water

at the same time if intending to use the water softener

system. Refer to page 15 for Hardness level settings.

(Use a funnel when relling salt)

3) Wipe off any spilled salt around the water softener.

4) Fasten the cap tightly.

(Loosely fastened cap may cause rust due to salt spilled

into the container.)

5) Run the Quick course without dishes.

• Water softening salt can be purchased from salt distributors.

NOTE

! Check point

- Note for Fastening the Cap of the water softener.

• Seal the cap properly (by

aligning it horizontally and

turning it clockwise.)

BEFORE USING FOR THE FIRST TIME

•

If the rinse aid compartment flap is not closed properly, a large amount of rinse aid will release

into the tub and cause washability problems.

CAUTION

• If, after washing, you notice cloudy spots, streaks or water marks on your glassware, you

need to increase the setting level. If the glass is smeared or foam is present on the bottom,

select a lower setting.

NOTE

Step 4. Adding rinse aid

Rinse aid must not be added if dish washing tablets are used which contain a built in Rinse

aid. Too much or too little rinse aid can inhibit the drying performance.

1) Press the lever on the top of the

rinse aid compartment so that

the ap opens.

2) Pour the rinse up to the

maximum level indicator at the

bottom.

3) Adjust the quantity of rinse by

rotating the adjuster.

4) Close the cap after adjustment.

※

Rinse level setting

• You can adjust the quantity of rinse from level 1 to

level 6.

• The higher the level, the more rinse aid dispensed.

• If drying performance is not good, adjust the indicator

to a higher level.

■ Appliance loaded in accordance with

standard specifications.

• Capacity : 14 place settings

• Comparability course : Eco and Soft Spray

• Rinse Aid setting : 4

• Reference cleaner : 25g of detergent onto

the inside surface of the door.

• Door is opened at the end of the drying

cycle for the drying performance test.

(Door position : Open 50 mm)

• Height-adjustable Rack-U must be inserted

into the uppermost position.

2. Upper Rack

1. Cutlery Basket

3. Lower Rack

Dinner Plates Soup Plates Dessert Plates

INFORMATION FOR ENERGY TEST

1 2 3 4 5

Glasses

Cups

Saucers

Knives

•

Do not place pots or pans with plastic handles in the washer as the handles may deteriorate due

to the heat and detergent.

•

Water proof or long lasting lipstick smudges on glasses may not be removed during the wash.

CAUTION

Daily use load

HOW TO USE AND OPERATE

1. Cutlery Basket

2. Upper Rack

3. Lower Rack

NOTE

Non dishwasher safe items

The combination of high water

temperatures and dishwasher detergent

may damage particular items, therefore

we do not recommend using the

dishwasher to wash the following:

• Copper or anodised aluminium

•

Hand painted silver or gold leaf crockery

• Wood or bone handled utensils

• Iron or non rust proof utensils

• Plastic items which are not dishwasher

safe

• Expensive ware such as silver and

dishes with golden rings

• Fragile item such as crystal glasses

For effective washing performance, always

follow the following instructions.

Remove large particles

of food debris from

plates including bones

etc. before loading.

Items with burnt on

food should be soaked

prior to loading in the

dishwasher.

Deep based items

should be placed upside

down.

Make sure that all

items do not touch

each other.

Take care not to

obstruct the rotation of

spray arms.

Plastic items will not

dry well, compared to

other items.

HOW TO USE AND OPERATE

•

To prevent injuries, place knives and other

utensils with sharp points on the cutlery

rack.

•

If you want to load them in the cutlery

basket, place them with the pointed edges

facing downwards.

WARNING

1. Cutlery Basket

Place forks and spoons in the cutlery basket

with their handles downwards.

For Large utensils, such as whisks, the cover

can be opened by being unhinged.

Take care not to obstruct the rotation of the

spray arm.

Slide two baskets in opposite directions, then

pull them apart.

①

②

The basket can be split along its length,

increasing the lower rack’s loading versatility.

The cutlery shouldn’t

be longer than 18cm.

(In this case, use the

cutlery rack.)

Max.

18cm

Page is loading ...

LG LD-1481S4 User manual

Brand: LG

Model: LD-1481S4

Category: Dishwashers

Type: User manual

This manual is also suitable for

Download PDF

report

LG LD-1481S4 User manual

This manual is also suitable for

LG LD-1481S4 User manual

Related papers

Other documents