Broan iQ Drive Furnace Blower Kit Installation guide

Brand: Broan

Model: iQ Drive Furnace Blower Kit

Type: Installation guide

Installation Instructions

WARNING:

To avoid the risk of electrical shock, personal

injury, or death, disconnect electrical power

before installing this kit or performing

maintenance.

Before beginning installation, read these instructions

thoroughly and follow all warning and cautions in these

instructions and on the unit. These instructions are primar-

ily intended to assist qualiﬁed individuals experienced in

the proper installation of this appliance. Some local codes

require licensed installation/ service personnel for this type

of equipment. Improper installation, service, adjustment,

or maintenance can cause ﬁre, electrical shock or other

conditions which may result in personal injury or property

damage. Unless otherwise noted in the instructions, only

factory authorized kits or accessories may be used when

modifying this product.

1. SPECIFICATIONS

The variable speed blower kit number 904621 is designed

for installation in all “B” and “C” cabinet upﬂow *G6 and

*GF1 furnaces only. This kit is not intended for use on

downﬂow furnaces.

2. INSTALLATION REQUIREMENTS

Check Equipment - After unpacking, inspect the kit

thoroughly for concealed damage. If damage is found,

notify the transportation company immediately and ﬁle a

concealed damage claim. All installations shall be made

as described in the installation instructions and in accor-

dance with applicable national and local codes including

the requirements of local utilities.

3. INSTALLATION

Conversion of Single Stage Upﬂow

Furnace

1. Disconnect electrical power to the furnace.

2. Remove the upper and lower access doors from the

furnace.

3. Remove the electrical plug containing the blower

wires from the receptacle located on the left side of

the blower deck.

4. Remove the screws that hold the blower assembly

and remove the blower.

5. Attach the blower mounting brackets, supplied in the

kit, to the blower housing.

6. Slide the variable speed blower kit into the furnace.

Be sure that the sides of the blower are captured by

all of the blower mounting tabs in the blower deck.

Secure with the two screws removed in step 4.

Blower Kit for Gas Furnace Applications

7. Remove the front cover from the control panel. Con-

nect the thermostat wires from the auxiliary board to

the integrated control board in the furnace.

IMPORTANT NOTE: All wires should be routed

through a strain relief bushing. All signal wires

(shielded wires) should be routed separately from

the single conductor wires.

8. Connect the pressure transducer from the coil to 4

pin terminal labeled "P3" on the EXV Board.

9. Connect the temperature sensor from the evapora-

tor coil to the 3 pin terminal labeled "P2" on the EXV

Board.

10. Connect the 1/4 inch coil thermister leads from the

evaporator coil to the indicated location on the auxiliary

board.

11. Connect the EXV coil from the evaporator coil to the

6 pin terminal on the EXV Board labeled "P1".

12. Replace the transformer on the furnace with the

60VA transformer (Part No. 622057) that is provided

in the kit, and connect to the furnace control board.

Self tapping screws may be required to install the

transformer.

13. Connect the Black wire from the noise ﬁlter to "L1"

on the furnace control board, and the White wire to

the neutral terminal on the control board. Use the

piggy back connector to re-attach the Black wire to

the board.

14. Connect the Blue wire that is placed on the "Twin"

terminal on the interface board to the "Twin" terminal

on the integrated control board on the furnace.

15. A set of thermostat wires is furnished with the kit.

These 4 wires are connected to the "Thermostat"

terminals on the interface board. These wires include

a noise ﬁlter ring. DO NOT REMOVE THE FILTER

RING. This has been supplied by the factory to avoid

electrical interference. Field supplied wire shall be

used to connect the Red wire to "R" on the thermostat

control, the Yellow wire to "A", the White wire to "B",

and the Green wire to "C".

16. A set of wires is furnished to connect the outdoor

condensing unit to the interface board. These 3 wires

are connected to the "O.D. Unit" terminals on the in-

terface board. These wires include a noise ﬁlter ring.

DO NOT REMOVE THE FILTER RING. Refer to the

outdoor unit installation instructions for connection.

IMPORTANT NOTE: The use of shielded cable

is required for the connection to the thermostat

controller. This wire is ﬁeld supplied. Ground the

shielded cable at the furnace end only on the

grounding lug on the interface board bracket.

Conversion of 2-Stage Upﬂow Furnaces

with Factory Installed Variable Speed

Blower (See Figures 1 & 3)

1. Disconnect electrical power to the furnace

2. Remove the upper and lower access doors from the

furnace.

3. Remove the screws that hold the blower assembly.

4. Remove the factory installed variable speed blower

including the wires connected to the integrated control

board in the furnace.

5. Remove all three wires that are fastened to the closed

end connector. Please note that one of the brown wires

is secured between the closed end connector and

the white wire on pin 13 of the variable speed motor.

These wires will not be used with the IQ Drive.

6. Remove the yellow wire from the Y-connector that

is attached to the gas valve. These wires will not be

used with the IQ Drive.

7. Connect the yellow wire from the W2 terminal of the

auxiliary board in the IQ Drive blower kit to the high

side terminal of the gas valve. (See Figure 2)

8. Install the IQ Drive blower kit as described in the

installation section for single stage furnaces, making

the conversions in steps 5 through 16.

Figure 2. Conversion of 95+ *TE Furnace

INTERFACE

BOARD

GAS VALVE

CONTROL

BOARD

ADD-ON

BOARD

RCYGW

W2 Y2

TWIN

LOW

CONDENSATE

PRESSURE SWITCH

LOW

WHITE

BLUE

RED

YELLOW

BLUE

YELLOW

BROWN

YELLOW

BROWN

123

456

FIGURE 2. 95+ FURNACE GAS VALVE WIRING

INTERFACE

BOARD

FURNACE

CONTROL

BOARD

GAS VALVE

HI LO C

YELLOW

BROWN

Figure 1. Wiring for furnaces with 2-stage gas valve.

Conversion of 2-stage Upﬂow Furnace with

Factory Installed Fixed Speed Blower

1. Disconnect electrical power to the furnace

2. Remove the upper and lower access doors from the

furnace.

3. Remove the screws that hold the blower assembly

and remove the blower.

4. Remove the DPST relay from the furnace and the

wires that connect to it. The relay and the wiring will

not be used with the IQ Drive.

5. Remove the brown wire that connects between the

DPST relay and the closed end connector in the fur-

nace. Also remove all three wires that are fastened

by the closed end connector. These wires will not be

used with the IQ Drive.

6. Remove the yellow Y-connector that is attached to

the gas valve. These wires will not be used with the

IQ Drive.

7. Install the IQ Drive blower kit as described in the

installation section for single stage furnaces, making

the conversions in steps 5 through 16.

8. Connect the yellow wire from the W2 terminal of the

auxiliary board in the IQ Drive blower kit to the high

side terminal of the gas valve. (See Figure 1)

Conversion of 92+ 2-stage Upﬂow Furnace

Models *TE Series with Factory Installed Vari-

able Speed Blower (See Figures 2 & 4)

1. Disconnect electrical power to the furnace

2. Remove the upper and lower access doors from the

furnace.

3. Remove the screws that hold the blower assembly

and remove the blower.

4. Install the IQ Drive blower kit as described in the

installation section for single stage furnaces, making

the conversions in steps 5 through 16.

5. Find wires that are fastened to the closed end connec-

tor. Please not that one of the brown wires is secured

between the closed end connector and the white wire

on pin 13 of the variable speed motor.

6. Remove the factory installed variable speed blower

including the wires connected to the integrated control

board in the furnace.

7. Cut and remove the brown wire from the variable speed

motor attached to the closed end connector. Insulate

the other end brown wire with insulation tape.

8. Disconnect the yellow wire from the low ﬁre side

terminal on the gas valve that leads to the variable

speed motor.

9. Attach the W2 wire from the Interface board to

the W2 terminal on Add-on combustion board.

(See Figure 2)

Figure 3. IQ Wiring Diagram

MOTOR

NOISE

FILTER

INTERFACE

BOARD

H Y

O.D. UNIT

I.D. BLOWER

THERMOSTAT

TWIN

DX+

DX-

GND

C R

DX-

DX+

OUTDOOR

UNIT

THERMISTOR

THRU CORE

RING

TEMP

SENSOR

COIL

THRU CORE

RING

POWER

CABLE

PLUG

CONNECTOR

GREEN

WHITE

RED

YELLOW

WHITE

GREEN

EXV

BOARD

SW2

THERM

SW1

COMM

EXV

OFF

SUCTION TEMP.

SENSOR

SUCTION PRESS.

SENSOR

PLUG

CONNECTOR

CONTROL

CABLE

HUM

EAC

THERMOSTAT

CONTROL

3 Amp Fuse

TWIN

COM

24 V

Neutrals

EAC

HUM

HEAT

COOL

XFMR

Unused Motor

Leads

120V

24V

WHITE

BLOWER OFF

180

120

FURNACE

BOARD

CONNECT TO

GAS VALVE

(TWO-STAGE

FURNACES ONLY)

RED

BLACK

RED

BLACK

WHITE

GREEN

BLACK

WHITE

RED

WHITE W/BLACK STRIPE

BLACK W/WHITE STRIPE

GREEN

WHITE

BLACK

WHITE

GREEN

YELLOW

WHITE

BLUE

RED

GRAY

YELLOW

710677 (Replaces 7106220)

Furnace Kit for System

Legend

Field Wiring

Factory Wiring:

Low Voltage

High Voltage

03/07

7106770

Figure 4. Wiring for 95+ 2-Stage Furnace

7106800

5. SELECTING BLOWER-OFF TIME

DELAY.

The blower off time delay can be adjusted through the

programming screen. The time delay can be adjusted

from 60 to 180 seconds. To enable this feature, the blower

off delay on the furnace board must be positioned to 60

seconds in order for the desired delay to be active. The

default setting on the thermostat is 120 seconds.

4. SELECTING THE GAS HEATING

AIRFLOW

To select the airﬂow, enter into the programming screen

on the controller thermostat. Select the input rate of the

gas furnace, then select the desired temperature rise.

PLEASE NOTE: Improper selection of the temperature

rise may result in limit operation. It is recommended that

a full furnace cycle is witnessed before the furnace is

placed in operation.

For 95+ 2-Stage Model Furnaces (2-Stage Inducer)

FLAME SENSOR

PRESSURE

LOW

HI HI

LOW

SWITCH

PRESSURE

SWITCH

BLOWER DOOR

SWITCH

TRANSFORMER

24 V

120 V

WHITE W/BLK STRIPES

BLK W/ WHITE STRIPES

IGNITO

2-PIN

HOUSING

6-PIN PLUG

3-PIN PLUG

3-PIN HOUSING

(SUPPLIED W/ INDUCER)

INDUCER

PRIMARY

GAS

VALV E

COM

24 V

3 AMP FUSE

BLOWER OFF

TWIN

FLAMESTATUS

VENT SAFETY SWITCH

HILOWC

SUPPLY AIR

LIMIT SWITCH

FLAME ROLL-OUT

SWITCH

ADD ON BOARD

Y2 W2

CONDENSAT E

BLOCKED VENT

EAC

HUM

HEAT

COOL

EAC

XFMR

NEUTRALS

R C

Y G W

MOTOR

NOISE

FILTER

345

O.D. UNIT

I.D. BLOWER

THERMOSTAT

TWIN

DX+

DX-

GND

DX-

DX+

GRD

COIL

THERMISTOR

TEMP

SENSOR

COIL

THR

4-PIN

HARNESS

U CORE

RING

THRU CORE

RING

POWER

BUSHING

CABLE

CONTROL

CABLE

INTERFACE

BOARD

BLACK

RED

YELLOW

WHITE

GREEN

RED

PLUG

3-PIN HARNESS

CONNECTOR

THERMOSTAT

CONTROL

OUTDOOR

UNIT

OUTDOOR

UNIT

9-PIN PLUG

456

RED

WHITE

GREEN

HARNESS

EXV

BOARD

SW2

THERM

SW1

COMM

EXV

OFF

SUCTION TEMP.

SENSOR

SUCTION PRESS.

SENSOR

GREEN

BLACK

WHITE

RED

EXV

6-WIRE CABLE

CABLE

WHITE

GREEN

BLACK

3-PIN PLUG

6-PIN PLUG

WHITE

BLACK

FURNACE

BOARD

GREEN

RED

YELLOW

GRAY

RED

BLUE

WHITE

BLACK

BLUE

ORANGE

WHITE

GREEN

BLACK

RED

BROWN

GREEN

ORANGE

YELLOW

BROWN

YELLOW

WHITE

BLACK

VIOLET

BLACK

RED

BLACK

WHITE

VIOLET

FIELD WIRING

LEGEND:

LOW VOLTAGE

HIGH VOLTAGE

STATUS

RED LIGHT

Power On ON

Limit Circuit Open or External Load On "W"1 FLASH

Pressure Switch is Open with Inducer On 2 FLASHES

Hi Pressure Switch is Open (Add-on board LED) 2 FLASHES

Pressure Switch is Closed with Inducer Off3 FLASHES

Ignition Failure (Check Ground) 4 FLASHES

115 VAC & Neutral Reversed or no Ground 5 FLASHES

False Flame or Gas Valve Relay ShortedContinuous

Power Of

OFF

FAULT CONDITION

FLAME

YELLOW

LIGHT

Low Flame Sensor Signal

Continuous

Flash

Flame Presen

NOTES:

1. Use copper conductors only.

2. If any of the original wires as supplied with the furnace must be replaced,

it must be replaced with wiring material having a temperature rating of at

least 105˚ C.

3. Refer to the Installation Instructions provided with the furnace for the

appropriate heating and cooling settings for your application.

4. Ensure that wires from the blower remain connected to the board thermo-

stat terminals after making the field thermostat connections.

708751A (Replaces 7087510)

Speciﬁcations & illustrations subject to change without notice or incurring obligations (05/15).

Broan iQ Drive Furnace Blower Kit Installation guide

Broan iQ Drive Furnace Blower Kit Installation guide

Broan iQ Drive Furnace Blower Kit Installation guide

Related papers

Other documents