Sharp LL-S242A-W Owner's manual

LL-S242A-W

LL-P202V

LCD MONITOR

MONITEUR LCD

MONITOR LCD

SETUP MANUAL

MANUEL D’INSTALLATION

MANUAL DE INSTALACIÓN

ENGLISH ...... E1

FRANÇAIS ..... F1

ESPAÑOL .... S1

ENGLISH FRANÇAIS ESPAÑOLENGLISH FRANÇAIS ESPAÑOL

IMPORTANT:

To aid reporting in case of loss or theft, please record the

product’s model and serial numbers in the space provided.

The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

WARNING:

FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the

manufacturer could void the user’s authority to operate this equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B computing equipment.

Declaration of Conformity

SHARP LCD MONITOR, LL-S242A-W/LL-P202V

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

Responsible Party: SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL: 1-800-BE-SHARP

U.S.A. ONLY

CAN ICES-3(B)/NMB-3(B)

CANADA ONLY

CANADA SEULEMENT

ENGLISH

1

E

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS

INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning ash with arrowhead symbol, within

a triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufcient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within a triangle is

intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your

product, please read the Safety Precautions carefully before using this product.

DEAR SHARP CUSTOMER

IMPORTANT INFORMATION

Contents

Read the manuals in the “Manual” folder of the provided CD-ROM. (Adobe Reader is required to view the manuals.)

[ENGLISH]

IMPORTANT INFORMATION ............................................1

DEAR SHARP CUSTOMER .............................................. 1

SAFETY PRECAUTIONS ..................................................2

SAFETY INSTRUCTION ...................................................3

Supplied Components ..................................................... 4

Applying the Logo Sticker ..............................................4

Binding Cables ................................................................. 5

Connecting Peripheral Equipment .................................6

Connecting the Monitor to a Power Source ..................7

Installation ........................................................................8

Turning Power ON/Off ...................................................11

Specications ................................................................12

The volume is set to 0 when the monitor is shipped from the factory.

2

E

SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly

handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can

result in electric shock and/or re. In order to prevent potential danger, please observe the following instructions when installing,

operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the

following precautions carefully before using the product.

1. Read instructions — All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future

reference.

3. Observe warnings — All warnings on the product and in the instructions must be observed closely.

4. Follow instructions — All operating instructions must be followed.

5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do

not use liquid cleaners or aerosol cleaners.

6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result

in accidents.

7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto

it. Be careful of equipment which drains water such as an air-conditioner.

8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.

Do not cover or block these vents and openings since insufcient ventilation can cause overheating and/or shorten the life

of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.

Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the

manufacturer’s instructions are followed.

9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from

resting on them.

10. The screen used in this product is made of glass. Therefore, it can break when the product is dropped or applied with

impact. Be careful not to be injured by broken glass pieces in case the screen breaks.

11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause re or electric shock.

12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage ows in

the product, and inserting an object can cause electric shock and/or short internal parts.

For the same reason, do not spill water or liquid on the product.

13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualied service person to perform servicing.

14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualied service

person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls

not described in the instructions can cause damage, which often requires extensive adjustment work by a qualied

technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product

needs servicing.

15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement

parts specied by the manufacturer, or those with the same characteristics and performance as the original parts. Use of

unauthorized parts can result in re, electric shock and/or other danger.

16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method

recommended by the manufacturer.

18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating

products (including ampliers).

19. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,

severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and

missile launch control in a weapon system.

20. Do not touch the parts of the product or the AC adapter that become hot for long periods of time. Doing so may result in

low-temperature burns.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal

and DisplayPort input terminal.

ENGLISH

3

E

- Do not use the monitor where there is a lot of dust, where

humidity is high, or where the monitor may come into contact

with oil or steam, as this could lead to re.

- Ensure that the monitor does not come into contact with

water or other uids. Ensure that no objects such as paper

clips or pins enter the monitor as this could lead to re or

electric shock.

- Do not place the monitor on top of unstable objects or in

unsafe places. Do not allow the monitor to receive strong

shocks or to strongly vibrate. Causing the monitor to fall or

topple over may damage it.

- Continuous Operation Time and Warranty

This product has been designed based on the assumption

of 15 or fewer hours of usage in one day. Continuous usage

that exceeds 15 hours in one day is not covered by the

warranty.

- Do not use the monitor near heating equipment or in places

where there is likelihood of high temperature, as this may

lead to generation of excessive heat and outbreak of re.

- Do not use the monitor in places where it may be exposed to

direct sunlight.

- The AC outlet shall be installed near the equipment and shall

be easily accessible.

- Do not use in applications where water or other uid may

adhere to the screen. If uid adheres to the screen, the touch

panel may not operate correctly.

- Do not use your nails, touch pens or digitizer pens other

than the one supplied, sharp pencils, or other hard objects to

operate the unit.

- If the pen tip of the digitizer pen is worn or damaged, replace

the pen tip. Failure to do so may scratch the screen or cause

the digitizer pen functions to not operate correctly.

SAFETY INSTRUCTION

The Power Cord and AC Adapter

- Use only the power cord and AC adapter supplied with the

monitor.

- When handling the AC adapter, observe the following:

Incorrect handling may result in re, electric shock, or injury.

• Do not drop the AC adapter or subject it to impact.

• Never disassemble the AC adapter. It contains high voltage

parts that are dangerous to touch.

• The AC adapter is for indoor use only. Do not use it outside.

• Do not use the supplied AC adapter with other devices.

- Do not damage the power cord and AC adapter nor place

heavy objects on it, stretch it or over bend it. Also, do not

add extension cords. Damage to the cord may result in re

or electric shock.

- Do not use the power cord with a power tap.

Adding an extension cord may lead to re as a result of

overheating.

- Do not remove or insert the power plug with wet hands.

Doing so could result in electric shock.

- Unplug the power cord if it is not used for a long time.

- Do not attempt to repair the power cord if it is broken

or malfunctioning. Refer the servicing to the service

representative.

- Do not stay in contact with the parts of the product and the

AC adapter that become hot for long periods of time.

Doing so may result in low-temperature burns.

- For your health, observe the following:

• If using the monitor continuously, take a 10- to 15-minute

break every hour to rest your eyes.

• Do not use the monitor in high-contrast light conditions.

• Do not use the monitor in locations where the screen is

subject to direct sunlight.

If a monitor is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many injuries,

particularly to children, can be avoided by taking simple precautions such as:

• Using xing devices like wall mount brackets recommended by the manufacturer.

• Only using furniture that can safely support the monitor.

• Ensuring the monitor is not overhanging the edge of the supporting furniture.

• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the

monitor to a suitable support.

• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.

• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.

SAFETY PRECAUTIONS (Continued)

4

E

Supplied Components

If any component should be missing, please contact your dealer.

Component LL-S242A-W LL-P202V

Liquid Crystal Display Monitor 1

AC adapter 1

Power cord 1

Digitizer pen - 1

Digitizer pen stand - 1

Digitizer pen cable clamper (clamper, xing screw: 1) - 1

Digitizer pen spare pen tips - 1

Touch pen 1 -

Variable stand (stand, xing screws: 4, hexagonal wrench) - 1

Rack stand (front, back, support, xing screws: 2) 1 -

USB cable (USB-microUSB Type B) 1

CD-ROM (Utility Disc) 1

Setup Manual (this manual) 1

Logo sticker 1

* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.

* Keep packaging for use when transporting monitor, etc.

Applying the Logo Sticker

You can apply the supplied logo sticker to the unit.

Attach as shown in the following diagram, as required.

Power LED

Landscape orientation Portrait orientation

ENGLISH

5

E

Binding Cables

Caution

• When connecting cables, spread a soft cloth on a stable level surface such as a desk, and gently place the monitor on it with

the screen facing down.

Video cable and USB cable

Secure the video cable (HDMI or DisplayPort) and USB cable using the cable clamp.

1. Remove the cable clamp.

Cable clamp

2. Route the cables through the cable

restraint slot.

Cable restraint

slot

3. Push the cable clamp down into

place.

Cable clamp

Digitizer pen cable

Secure the digitizer pen cable using the supplied clamper and xing screw.

1. Pass the digitizer pen cable through the ring of the clamper.

2. Attachtheclamperusingthexingscrew.

Clamper

Digitizer pen cable

Fixing screw

6

E

Caution

• Be sure to turn off the power and disconnect the plug from

the power outlet before connecting/disconnecting cables.

Also, read the manual of the equipment to be connected.

• Do not forcibly bend or apply force to cables. Doing so may

result in wire breakage or other damage.

• When connecting cables, spread a soft cloth on a stable

level surface such as a desk, and gently place the monitor

on it with the screen facing down.

• Do not use any cable that has a damaged or deformed

terminal. Using such cables may cause malfunctions.

• Connect USB devices that have the following thicknesses

around the connector area.

12mm

38mm

8mm

A

B

C

17mmD

D

B

C

A

TIPS

• Images may not be displayed properly depending on the

computer (video card) to be connected.

• To use the digitizer pen, the necessary software must be

installed on the computer from the supplied CD-ROM.

• When connecting a USB device to the USB terminal, use

only USB devices with current consumption of 500mA or

lower.

Connection with a PC

Connect the monitor and a PC using the connection cable.

n

Inputting video and audio

HDMI input terminal

Commercially available HDMI cable

(conforming to the HDMI standard)

To HDMI output

terminal on PC

Check the orientation of the connector and insert it horizontally

as far as it will go.

• It is possible to connect the monitor’s HDMI input terminal

to a smartphone or similar MHL-compliant device using a

commercially available MHL cable.

This product supports MHL 1.

Connecting Peripheral Equipment

DisplayPort input terminal

Commercially available DisplayPort cable

To DisplayPort output

terminal on PC

Check the orientation of the connector and insert it horizontally

as far as it will go.

TIPS

• The length of the signal cables or surrounding environment

may affect the image quality.

• The video from the terminal that has signal input is

displayed. In this state, even if a signal is input from the

other terminal, the display is not switched. To switch the

display, use [Input Select] on the menu screen.

• If the LCD monitor is turned on when there are input signals

from both terminals, the video from the DisplayPort input

terminal is displayed (factory default).

• The terms HDMI and HDMI High-Denition Multimedia

Interface, and the HDMI Logo are trademarks or registered

trademarks of HDMI Licensing LLC in the United States

and other countries.

• DisplayPort is a registered trademark of Video Electronics

Standards Association.

• MHL, the MHL logo, and Mobile High-Denition Link are

trademarks or registered trademarks of MHL, LLC in the

United States and other countries.

n

Using the touch panel

To use the touch panel, connect the monitor to a USB port on

a PC using the supplied USB cable.

USB terminal

Touch panel terminal

Supplied USB cable

To USB port on PC

Check the orientation of the connector and insert it horizontally

as far as it will go.

ENGLISH

7

E

Connecting Peripheral Equipment (Continued)

Connecting USB devices

When using a commercially available mouse, keyboard, or

other device, connect the device to the USB port.

USB terminal

USB cable

Check the orientation of the connector and insert it horizontally

as far as it will go.

Connecting the Monitor to a Power Source

Caution

• Use only the AC adapter and power cord supplied with the monitor.

1. Connect the monitor to the power outlet using the supplied AC adapter and power cord.

AC adapter core

Core restrainer

Back of monitor

AC adapter

connection terminal

Power cord

(Supplied)

AC adapter (Supplied)

For power

outlet

2. Push the AC adapter core into the core restrainer.

Connecting the digitizer pen

(LL-P202V)

When using the supplied digitizer pen, connect the digitizer

pen cable.

Digitizer pen connection terminal

Digitizer pen cable

Check the orientation of the connector and insert it horizontally

as far as it will go.

8

E

Installation

You can install the touch display for each monitor in the

following positions.

Installation position LL-S242A-W LL-P202V

Standing

position

Rack stand Yes No

Variable stand

No Yes

Pen writing position No Yes

Horizontal position Yes Yes

Installing on a stand

(Standing position)

n

LL-P202V

Placement on the variable stand

Place the unit on the supplied variable stand.

Caution

• The variable stand is designed for placement of the unit in

the landscape orientation. It cannot be used for the portrait

orientation.

• For installation, place the monitor face-down carefully on a

soft cloth on top of a at, stable surface.

• Applying excessive pressure to the LCD panel with your

hands may result in damage to the unit.

• Be careful not to get your ngers caught when adjusting the

angle, for example.

1. Place the variable stand on the rear of the monitor,

insertthexingscrewsandtightenbyhandtoposition

the stand.

2. Securelytightenthexingscrewsusingthesupplied

hexagonalwrench.

3. Place the monitor in the standing position, and adjust

the angle of the stand.

Hold the display with one hand so that it does not fall over,

hold the rear leg of the stand with your other hand, and

adjust the angle of the stand.

The legs can extend about 20 to 75 degrees in relation to

the at surface.

20°

75°

ENGLISH

9

E

Installation (Continued)

n

LL-S242A-W

Placement on the rack stand

Place the unit on the supplied rack stand.

1. Attach the back of the stand to the front.

Place the front and back sides together, and attach the

hinge.

Back

Front

Front hinge part

Back

Support

Tape

Front

Back hinge part

2. Spread the base of the front and back sides.

3. Peel off the adhesive tape securing the support to the

back side.

Back

Support

Tape

4. Fold down the support, inserting the tabs into the

holes on the front side.

5. Position the stand.

6. Place the monitor in the stand.

Landscape orientation

Run the cables out between the legs of the back side.

10

E

Installation (Continued)

Portrait orientation

Run the cables along the hollow on the front side and out

between the legs of the back side.

7. Securethemonitortothestandusingthetwoxing

screws.

Landscape orientation

Fixing screws (supplied)

Portrait orientation

Fixing screws (supplied)

Installing on a table

(Pen writing position/Horizontal

position)

Remove the monitor from the stand and place face-down on a

table or other level surface.

Caution

• Do not exert a large amount of force on the monitor from

above. Doing so may damage the ap. (LL-P202V)

• After removing the monitor from the rack stand, store the

stand so that the screws will not be lost.

n

LL-P202V

Pen writing position

Place the monitor on a table or other level surface.

1. Holdtheapbythedepressiononthebackofthe

monitorandpulltheapup.

Depression

2. Place the monitor where you want to use it.

Horizontal position

Place the monitor on a table or other level surface.

Caution

• When using the monitor horizontally, use the horizontal tab

in the upright position.

1. Lift up the two tabs on the back of the monitor.

ENGLISH

11

E

Installation (Continued)

Turning Power ON/Off

Turning on the power

1. Press the POWER button.

Press

POWER button

Power LED

The power LED turns on.

2. Turn on the PC.

The screen appears.

Status Status of the monitor

Green lit Signal input

Orange lit No signal input

Alternately ashing red and

green

Abnormal temperature

Caution

• When switching the POWER button off and back on,

always wait for an interval of at least 5 seconds. Rapid

switching may lead to errors or malfunctions.

• For a complete electrical disconnection, pull out the main

plug.

Turning off the power

1. Turn off the PC.

2. Depress the POWER button for around 2 seconds.

Depress for around

2 seconds

POWER button

The power LED turns off.

Caution

• If the monitor will not be used for a long time, disconnect

the power plug from the power outlet.

2. Place the monitor where you want to use it.

n

LL-S242A-W

Horizontal position

Place the monitor on a table or other level surface.

1. Simply lay the unit on the desired location.

12

E

Specications

Model LL-S242A-W (white) LL-P202V

Power requirement AC 100 V - 240 V, 50/60 Hz (when using the supplied AC adapter),

DC 19 V

Operating temperature 32°F to 95°F (0°C to 35°C)

Operating humidity 20% to 80% (no condensation)

Power consumption

(during normal operation) *

48W (36W) (when using supplied

AC adapter)

41W (29W) (when using supplied

AC adapter)

Dimensions (excluding protrusions) inch (mm) Approx. 22-5/16 x 1-1/8 x 13-5/16

(566.4 x 28.7 x 338.3) (WDH)

Approx. 18-1/4 x 1 x 10-13/16

(463.8 x 25.2 x 274.8) (WDH)

Weight lbs. (kg)

Approx. 10.58 (4.8) (excluding stand)

Approx. 12.13 (5.5) (including stand)

Approx. 5.07 (2.3) (excluding stand)

Approx. 7.94 (3.6) (including stand)

* When the DisplayPort input terminal and touch panel are connected.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement

without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from

these values in individual units.

Page is loading ...

Printed in China

Imprimé en China

Impreso en Chine

14A KS1

TINSE1348MPZZ(1)

Sharp LL-S242A-W Owner's manual

Sharp LL-S242A-W Owner's manual

in other languages

Related papers

Other documents