Mastervolt Remote ICC User manual

Mastervolt
Brand
Mastervolt
Model
Remote ICC
Type
User manual
REMOTE ICC ENGLISH
DIMENSIONS
PRODUCT DESCRIPTION AND APPLICATION
With the Remote ICC you can operate and check the actual status of
the Mass Combi remotely. A remote connection cable (6m) is
included with the delivery.
SAFETY REGULATIONS AND MEASURES
• Install the Remote ICC according to the stated instructions.
• Only allow changes in your electrical system to be carried out by
qualified electricians.
• Connections and safety features must be executed according to
the locally applicable regulations.
• Do not work on the Mass Combi and/or the electrical installation if
it is still connected to the external AC or DC.
INSTALLATION
(see also the user’s manual of the Mass Combi)
1. Switch off the Mass Combi and disconnect the external AC power.
Then remove the DC fuses.
2. Make a cut out using the outline drawings of Figure 1.
3. Open the connection compartment of the Mass Combi. Refer to
the user’s manual of the Mass Combi.
4. Connect the communication cable between the REMOTE
connection of the Mass Combi and the Remote ICC (Figure 2).
5. Close the connection compartment of the Mass Combi.
GUARANTEE TERMS
Mastervolt guarantees that the Remote ICC has been built according
to the legally applicable standards and stipulations. If you fail to act
in accordance with the regulations, instructions and stipulations of
this user’s manual, damage can occur and/or the unit will not fulfill
the specifications. This may mean that the guarantee will become
null and void.
The standard period is 2 years.
LIABILITY
Mastervolt cannot be held liable for:
• Consequential damage resulting from the use of the Remote ICC.
• Possible errors in the included manual and the consequences of
these.
• Use that is inconsistent with the purpose of the product.
CONNECTION
OPERATION
Mastervolt International B.V, P.O.Box 22947, NL-1100 DK Amsterdam, The Netherlands. Tel.: +31-20-3422100 Email: info@mastervolt.com Web: www.mastervolt.com v1.0 071218EN
Figure 1
Dimensions in mm [inch]
39 [1.54]
39
[
1.54
]
40
[
1.57
]
52
[
2.05
]
6
[
0.24
]
18.5
[
0.73
]
118.5 [4.67]
110 [4.33]
128 [5.04]
140 [5.51]
MASTERBUSREMOTE QRS232
+5A
NEG
TEMP. SENS
BATTERY
1 - 2 - 3 - 4
POS
+
“REMOTE”
connection
ICC panel
Figure 2
DC load
Charger mode: Displays the DC
charge current as a percentage of the
maximum current
Inverter mode: Displays the AC power
as a percentage of the maximum power
State of Charge
Charger mode: Displays the state
of charge, bulk, absorption or float
Inverter mode: Displays the
approximate battery voltage
Inverter LED
Green: the Mass Combi is operating in
inverter mode
Red: an error is detected
Charger LED
Green: the Mass Combi is
operating in charger mode
Red: an error is detected
AC Input
Illuminated: incoming AC power is
available and within specifications
Fast blinking: incoming AC power is
available, but quality is insufficient
Failure LED:
When illuminated red, a failure is
detected. The cause of failure is
explained in the user manual of the Mass
Combi.
On/Off switch. Notes:
• This switch will not operate if the main switch on the Mass Combi is set to Off.
• The Mass Combi is not entirely off when the Mass Combi is switched off via the Remote
ICC. The no-load drain is less then 5mA and is used to keep the data buses connected to
the remote panel active
Figure 3
  • Page 1 1

Mastervolt Remote ICC User manual

Mastervolt
Brand
Mastervolt
Model
Remote ICC
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents