Zebra RA3051 Owner's manual

Type
Owner's manual

Zebra RA3051 is a WWAN radio kit with antennas that provides WAN, GPS, and Wi-Fi diversity. It includes a UMTS PHS8-P Expansion Module, M2x4 Torx T6 screws, a GPS jumper cable, a WAN main antenna, and a WAN diversity antenna.

This radio kit allows you to add WAN, GPS, and Wi-Fi capabilities to your Zebra handheld device. With the WAN capabilities, you can connect to the internet and access data from anywhere with a cellular signal. The GPS capabilities allow you to track your location and use navigation apps. The Wi-Fi diversity feature ensures that you have a strong and reliable Wi-Fi connection, even in areas with weak or congested Wi-Fi signals.

Zebra RA3051 is a WWAN radio kit with antennas that provides WAN, GPS, and Wi-Fi diversity. It includes a UMTS PHS8-P Expansion Module, M2x4 Torx T6 screws, a GPS jumper cable, a WAN main antenna, and a WAN diversity antenna.

This radio kit allows you to add WAN, GPS, and Wi-Fi capabilities to your Zebra handheld device. With the WAN capabilities, you can connect to the internet and access data from anywhere with a cellular signal. The GPS capabilities allow you to track your location and use navigation apps. The Wi-Fi diversity feature ensures that you have a strong and reliable Wi-Fi connection, even in areas with weak or congested Wi-Fi signals.

The RA3051 radio kit includes the UMTS PHS8-P Expansion Module along with the following:
M2x4 Torx T6 screws (x4)
GPS jumper cable
WAN main antenna
WAN diversity antenna
1. Remove the end-cap (x4 screws), back cover (x6 screws), and battery.
2. Remove the metal frame (x4 screws), and remove the existing Wi-Fi antenna
3. Slide the Diversity Antenna into the grooves along the right side of the unit.
4. Route the cables as indicated on the board – insert the red Wi-Fi antenna into the socket labelled Red and the green GPS antenna into the socket
labelled Green. Secure the cables by routing them through the clips.
CAUTION Installation of any components must be performed using appropriate anti-static devices. If unavailable, discharge body static by
touching a grounded metallic object before opening any covers on the hand-held.
Installation of any components must be performed
using appropriate anti-static devices. If unavailable, discharge body static by touching a grounded metallic object before opening any
covers on the hand-held.
.
NOTE If the unit does not have an imager or scanner end-cap attached, the WA6212 long blank end-cap is required. The WA6212 end-cap is
not included in the RA3051 kit. It must be ordered separately.
Metal
frame
Wi-Fi
antenna
Wi-Fi Diversity
antenna
Route cables through clips
GPS antenna
(green)
Wi-Fi Main antenna
(red)
RA3051 WWAN RADIO KIT WITH ANTENNAS
(WAN/GPS/WI-FI DIVERSITY)
INSTALLATION INSTRUCTIONS
8000323-001 Revision A — March 2015
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment,
they will contact the Global Support Center at: http://www.zebra.com/support
.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies Company.
© 2015 Symbol Technologies, Inc.
5. Insert the flex cable into the camera connector on the unit, using the white indicator to ensure proper alignment. Push the connector latch down to
lock it in place.
6. Press down on the flex cable to ensure that the double-sided adhesive has secured the flex cable in place.
7. Peel the liner away from the supplied white adhesive tape, and align it with the edge of the rubber square on the flex cable.
8. Press down on the tape to attach it to the flex cable, and fold the tape under so that it sticks to the board.
9. Install the back cover using the 6 screws provided, torqued to 2.5 in-lbs.
10. Install the end-cap (x4 screws), torqued to 2.5 in-lbs.
11. Install the battery and battery cover.
For this installation, you will need the following:
desktop docking station
USB flash drive
BooST script software – To receive the appropriate BooST script software release, contact:
www.zebra.com/support
Camera back cover
Camera connector
Press down here
  • Page 1 1
  • Page 2 2

Zebra RA3051 Owner's manual

Type
Owner's manual

Zebra RA3051 is a WWAN radio kit with antennas that provides WAN, GPS, and Wi-Fi diversity. It includes a UMTS PHS8-P Expansion Module, M2x4 Torx T6 screws, a GPS jumper cable, a WAN main antenna, and a WAN diversity antenna.

This radio kit allows you to add WAN, GPS, and Wi-Fi capabilities to your Zebra handheld device. With the WAN capabilities, you can connect to the internet and access data from anywhere with a cellular signal. The GPS capabilities allow you to track your location and use navigation apps. The Wi-Fi diversity feature ensures that you have a strong and reliable Wi-Fi connection, even in areas with weak or congested Wi-Fi signals.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI