Deck Impressions 90032-132PBL-WT Installation guide

Brand: Deck Impressions

Model: 90032-132PBL-WT

Type: Installation guide

This manual is also suitable for

Parts List:

Step 1:

Fig. 2

Fig. 1

Step 3:

Fig. 3

Step 4: Attach top and bottom rails to deck posts (Fig. 4) and drill 1/4" hole in deck posts for wire (Fig. 5).

Fig. 4 Fig. 5

Step 5: Reinstall screw covers previously removed in Step 3 above and feed wire through post and across top rail connectors. Fig. 6

Important - Screw Cover Installation -

Step 2: Cut top and bottom rails to length, allowing for rail mounts of

fit and size. Place rails face to face. Starting from the center of the

rails, mark 4 1/8" on center. Fig. 2

The T2 screw cover must be properly installed for the system to work.

Improper installation of the screw cover will prevent the pierce connectors

from making electrical contact with the wire. Elimination of this critical part

from the assembly could result in an electrical short should the pierce

connectors contact the metal head of the screw. The T2 screw cover is

intended to be installed with the hollow center facing the screw head (see

Ill. A). The opposite side of the cover forms the seat for the pierce

connectors to contact the wire (see Ill. B). The side that faces the baluster

has a raised center and raised outer edge, forming a channel between the

inside and outside edge. The T2 screw cover fits snugly when aligned and

pressed into place. Access to the mounting screw for replacement of

damaged rails or balusters will require the removal of the T2 screw cover.

Measure rails from post to post. Fig. 1

For Lighted Baluster Models 171-Series

Lighted Baluster Installation Instructions

For Use With Landscape Lighting Systems Only

Deck Impressions

Parts Diagram

Read and Save These Instructions

Outdoor Use Only

Ill. B (Faces wire)

Fig. 3A Fig. 3B Fig. 3C

Ill. A (Covers screw head)

Fig. 6

from the top rail connector and remove top rail connector

from baluster (Fig. 3A). Using one of the provided

mounting screws, push the pointed end of the screw

through the hole in the back side of the rail connector to

pop out the plastic screw head cover (Fig. 3B). The

bottom rail connector can be removed from the opposite

end of the lighted baluster by sliding the connector sleeve

up the baluster (Fig. 3C). Attach baluster rail connectors

to the top and bottom rails using the screws provided. For

non-lighted balusters, use accessory Deck Impressions

mounting hardware 171-7620 (sold separately). Fig. 3

For lighted balusters, unscrew the rail connector sleeve

T2 - screw cover

T4 - threaded collar

B2 - bottom sleeve

T1 - top rail connector

T3 - pierce connector

B1 - bottom rail connector

Step 6:

Fig. 8

Fig. 7

Step 8:

Fig. 9

Step 9: (Optional - requires accessory part # 171-7626, Sold Separately)

Cover exposed wire with Deck Impressions wire covers. Fig. 10.

Mixing Lighted and Non-Lighted Balusters?

Fig. 10

Align pierce connectors with 16 AWG SPT-2W landscape wire. Press firmly to pierce wire. Fig. 7. For installation of non-lighted

balusters, follow instructions included with accessory hardware pack 171-7620 (sold separately).

Limited 5 Year Warranty: Creative Industries warrants the lighted balusters to be free from defects in material and workmanship for a period of five

(5) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and

service. If this product is found to be defective, Creative Industries' only obligation and your exclusive remedy, is the repair or replacement of the

product at Creative's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect

or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in a way not in

accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse,

abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to

the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. Creative does not warrant and

specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. Creative

Industries specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any

labor expense costs involved in the replacement or repair of said product. Some states do not allow the exclusion or limitation of incidental

consequential damages, so the limitations and exclusions above may not apply to you. This warranty is in lieu of all other express or implied

warranties. All implied warranties, including the warranty of merchantability and the warranty of fitness for a particular purpose are hereby modified to