Viking Range DDFF136 Operating instructions

Viking Range
Brand
Viking Range
Model
DDFF136
Type
Operating instructions

This manual is also suitable for

Viking Installation Guide
Free-Standing Refrigeration
Side Trim & Grille Installation
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
2
Required Components
Remove and discard screw and hinge cover. Remove
screw on hinge plate.
(Repeat if two hinges are used.)
Remove and discard plug button from hole on
non-hinge side.
Remove three screws from mullion area opposite the
center hinge.
Install set screws from bag into holes from
previous step.
Remove edge of corner cover.
Left Panel
Left Trim
Right Panel Right Trim
Front Grille
Adhesive
Tape
Set
Screws
Screws
Spacer
L Bracket
A
C
B
1
Bottom Mount Model Only
2
Bottom Mount Model Only
3
Bottom Mount Model Only
4
5
Installation
3
6
French Door and Side-by-Side Dispenser Models only
7
French Door and Side-by-Side Dispenser Models only
Unplug harnesses on door.
Remove ground screw from hinge on door. Hold for
replacement.
8
French Door and Side-by-Side Dispenser Models only
9
French Door and Side-by-Side Dispenser Models only
Apply electrical tape to harnesses and ground wire
coming from door.
Plug in proper harness kit to the harness
coming from the door.
10
French Door and Side-by-Side Dispenser Models only
B
A
A
11
Apply adhesive tape to grille assembly.
Attach brackets included in the kit to the grille
assembly.
4
Position spacers included in the kit on the non-hinge
side over the exposed hole from step one.
Feed wire harness and ground wire through the bottom
of the endcap and out through the hole in the rear of
the grille.
Bottom Mount Model only
12
13
French Door and Side-by-Side Dispenser Models only
Connect wire harness to wire harness
in cabinet. Connect ground screw. Secure wire harness
to top of the cabinet with a piece of tape.
14
French Door and Side-by-Side Dispenser Models only
15
1
2
French Door and Side-by-Side Dispenser Models only
Remove adhesive backing. Firmly press the grille
assembly down so the adhesive adheres to the cabinet.
Align grille assembly to front door and position grille
on top of unit.
C
16
Secure the grille brackets to the holes in the hinge plate.
17
72”
Raise the unit up until the measurement from the floor
to the top of the grille assembly is 72 inches or 6 feet.
5
18
2
1
2
Remove adhesive backing for the side trim. Locate the
top of the side trim with the top of the grille assembly.
Press the side trim into the refrigerator cabinet at the
center location.
19
2
2
1
complete
Shim trim has adhesive backing on both sides. Remove adhesive
backing on refrigerator side only. Fit the shim trim to the front of the
unit first. With center hinge, the shim trim will have a cutout. Use the
cutout to locate the height of the shim trim. Without a center hinge,
locate the top of the shim trim with the top of the refrigerator cabinet
.
6
7
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20426
(PS0605VR)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Viking Range DDFF136 Operating instructions

Viking Range
Brand
Viking Range
Model
DDFF136
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents