Vulcan-Hart GCT60 User manual

Brand: Vulcan-Hart

Model: GCT60

Type: User manual

This manual is also suitable for

INSTALLATION & OPERATION MANUAL

VULCAN ENDURANCE Series

Gas Hot Plates

MODELS:

GCT12 GCT24

GCT36 GCT48

GCT60 GCT72

www.vulcanhart.com

ITW Food Equipment Group, LLC

10405 Westlake Drive

Charlotte, NC 28273

RETAIN THIS MANUAL FOR FUTURE USE

FORM F38202 Rev. A (07-08)

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED

FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

In the event a gas odor is detected, shut

down units at main shutoff valve and

contact the local gas supplier for service.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors or liquids in the vicinity of

this or any other appliance.

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, injury or death. Read the

installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

- 2 -

- 3 -

INSTALLATION, OPERATION AND CARE OF

VULCAN ENDURANCE SERIES GAS HOT PLATES

PLEASE KEEP THIS MANUAL FOR FUTURE USE

GENERAL

Vulcan hot plates are produced with quality workmanship and material. These hot plates are designed

with efficiency in cooking performance, sanitation, and ease of cleaning in mind. Proper installation,

usage and maintenance of your hot plate will result in many years of satisfactory performance.

The manufacturer suggests that you thoroughly read this entire manual and carefully follow all of the

instructions provided.

OPTIONAL FIELD INSTALLABLE ACCESSORIES

DESCRIPTION

ACCESSORIES

Flex Hose and Quick

Disconnect

- ¾” (18.75 mm) flex hose / disconnect, 4’ (1219 mm long).

- 1" (25 mm) flex hose / disconnect, 4' (1219 mm) long.

INSTALLATION

UNPACKING

This hot plate was inspected before leaving the factory. The transportation company assumes full

responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for

possible shipping damage. If the hot plate is found to be damaged, save the packaging material and

contact the carrier within 15 days of delivery.

If burner has been shipped using any package strapping devices, remove these before installing the hot

plate.

Before installing, check the type of gas supply (natural or propane) to make sure they agree with the

specifications on the rating plate located on the side of the hot plate. If the supply and equipment

requirements do not agree, do not proceed with the installation. Contact your dealer immediately.

LOCATION

The equipment area must be kept free and clear of combustible substances.

Installation clearances: COMBUSTIBLE NON-COMBUSTIBLE

CONSTRUCTION

Back: 6" (152 mm) 0"

Right Side: 10" (254 mm) 0"

Left Side: 10" (254 mm) 0"

The installation location must allow adequate clearances for servicing and proper operation. A minimum

front clearance of 24" (610 mm) is required.

- 4 -

The hot plate(s) must be installed so that the flow of combustion and ventilation air will not be

obstructed. Adequate clearance for air openings into the hot plate(s) must be provided. Make sure

there is an adequate supply of air in the room to allow for combustion of the gas at the burners.

INSTALLATION CODES AND STANDARDS

Your Vulcan hot plate must be installed in accordance with:

In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). This shall include but

not be limited to: NFPA #54 Section 10.3.5.2 for Venting. Copies may be obtained

from The American Gas Association Accredited Standards Committee Z223, @ 400 N.

Capital St. NW, Washington, DC 20001 or the Secretary Standards Council, NFPA, 1

Batterymarch Park Quincy, MA 02169-7471.

NOTE: In the Commonwealth of Massachusetts

All gas appliances vented through a ventilation hood or exhaust system equipped with

a damper or with a power means of exhaust shall comply with 248 CMR.

3. NFPA Standard # 96 Vapor Removal from Cooking Equipment, latest edition, available

from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

In Canada:

1. Local codes.

2. CAN/CSA-B149.1 Natural Gas Installation (latest edition)

3. CAN/CSA-B149.2 Propane Installation Code (latest edition), available from the

Canadian Gas Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3

The above are available from the Canadian Standard Association, 5060 Spectrum Way, Suite 100,

Mississauga, Ontario, Canada L4W 5N6.

CASTER EQUIPPED HOT PLATES

Hot plates mounted on casters must use a flexible connector (not supplied by Vulcan) that complies

with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69•CSA 6.16 and a quick-

disconnect device that complies with the Standard for Quick-Disconnect Devices for Use With Gas

Fuel, ANSI Z21.41•CSA 6.9. In addition, adequate means must be provided to limit movement of the

appliance without depending on the connector and the quick-disconnect device or its associated piping

to limit appliance movement. Attach the restraining device at the rear of the hot plate.

If disconnection of the restraint is necessary, turn off the gas supply before disconnection. Reconnect

this restraint prior to turning the gas supply on and returning the hot plate to its installation position.

If the hot plate is installed on casters and is moved for any reason, it is recommended that the hot plate

be re-leveled front to back and side to side.

LEVELING

To level the hot plate, place a carpenter's level on the hot plate and check leveling of the unit side to

side and front to rear. Achieve leveling by turning each foot section of the unit's leg as needed. Turning

the foot in a counter clockwise direction will increase height and clockwise will decrease.

GAS PRESSURE REGULATOR

A preset gas pressure regulator and street elbow is shipped with the hot plate. This regulator must be

installed by an authorized service person before the unit is placed into operation. See full unit data plate

located on the side of the hot plate, for pressure regulator setting information. If a manometer is being

used, utilizing one of the available pressure taps in the manifold, the manifold pressure with one burner

on should be ± 0.3" W.C. of the value indicated on the rating plate.

1. Locate the gas connection pipe protruding through the back of the unit.

2. Cover the pipe threads with pipe joint compound resistant to propane gases.

3. Screw the regulator onto the pipe hand tight with flow direction arrow pointing towards the back of

the unit and the regulator adjustment in the up right position.

4. With a pipe wrench, tighten the regulator securely in the upright position. (The regulator is preset

and should not require any additional adjustments.) The pressure regulator must be mounted

horizontally to ensure the proper preset outlet pressure. If mounted in any other direction, the outlet

pressure must be rechecked and possibly reset. A leak limiter is supplied with every regulator to

allow excess gas pressure to escape. Do not obstruct the limiter or the gas regulator, as obstruction

may cause the regulator to malfunction.

GAS CONNECTIONS

All gas supply connections and any pipe joint compound used must be resistant to the action

of propane gases.

Prior to lighting, check all joints in the gas supply line for leaks. Use soap and

water solution. Do not use an open flame.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

TESTING THE GAS SUPPLY SYSTEM

When test pressures exceed ½ psig (3.45 kPa), the hot plate and its individual shutoff valve must be

disconnected from the gas supply piping system.

When test pressures are ½ psig (3.45 kPa) or less, the hot plate must be isolated from the gas supply

system by closing its individual manual shutoff valve.

FLUE CONNECTIONS

DO NOT obstruct the flow of flue gases from the flue located on the rear of the hot plate. Proper

venting of flue gas is vital to the safe and efficient operation of the hot plate. Problems arising from the

intentional obstruction of the flue will result in voiding of warranty. It is recommended that the flue

- 5 -

gases be ventilated to the outside of the building through a ventilation system installed by qualified

personnel.

From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18"

(457 mm) must be maintained. Information on the construction and installation of ventilating hoods

may be obtained from the standard for "Vapor Removal from Cooking Equipment," NFPA No. 96 (latest

edition), available from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

OPERATION

The appliance and its parts are hot. Use care when operating, cleaning, or

servicing the appliance.

CONTROLS

Open Top Burner Valve — Allows gas to flow to the top burners. To open valve, turn knob

counterclockwise. To close valve, turn knob clockwise.

LIGHTING AND SHUTTING DOWN PILOTS

1. Remove front row of grates.

2. Turn the main gas supply valve to the ON position.

3. Light all standing pilots. Pilot access can be reached under the grate support beam running from

left to right.

4. Turn the burner valve ON to the desired heat.

5. If burners fail to light, turn off all valves, and then call an authorized installation or service person.

6. To shut down, turn the burner valve to the OFF position.

7. For complete shut down, turn all burner valves to the OFF position. Turn off main gas supply.

OPERATING SUGGESTIONS

Open-top burners are quickly lit and require no preheating time. Open top burners have a wide low to

high burner flame adjustment hot plate. This allows for better simmering performance at the lowest

possible stabilized setting. When simmering, turn the burner valve knob down until you reach the

optimum lowest burner flame setting to maintain the desired simmer point.

CLEANING

Shut off the gas before cleaning the appliance.

The appliance and its parts are hot. Be very careful when operating, cleaning, or

servicing the appliance.

Exterior surfaces may be cleaned using soft cloth and mild detergent. Do not use Dawn

® dish detergent

to clean the exterior or interior components of the hot plate.

- 6 -

- 7 -

Vulcan equipment is strongly constructed and is designed to give you long, satisfactory service at low

cost, provided you give it proper care. Frequent cleaning and occasional adjusting should reward you

with low operating and maintenance costs and faster, better service.

DAILY CLEANING

Clean cast iron open top grates with a mild soap and water solution. Rinse thoroughly and dry with a

clean, water-absorbent towel. Immediately after drying (with grates still removed from the hot plate top),

season grates lightly with liquid vegetable or spray-type cooking oil.

After seasoning, replace grates onto the hot plate. Turn on all open top sections to LOW and allow

them to burn for at least 15 minutes before using pots or pans on the hot plate top. Season the open

top grates after each cleaning. Failure to season grates will cause grates to rust.

EXTERIOR CLEANING

Daily

Clean exterior finish with a mild solution of soap or grease-dissolving cleaner. To remove discoloration,

use a nonabrasive cleaner. Always rub with the grain of the metal. Stainless steel areas of the hot plate

can be polished by using a soft dry cloth. If needed, add stainless steel polish to the soft cloth.

STAINLESS STEEL

Here are a few simple cleaning procedures that have been found effective for keeping stainless steel

equipment clean, sparkling and bright.

General Cleaning

Use ordinary soap or detergent and water for routine cleaning of stainless steel. To prevent water spots

and streaks, rinse thoroughly with warm water and wipe dry with a soft clean cloth. The addition of a

rinsing agent will also help prevent spotting. Do not pressure wash any portion of the hot plate.

Fingerprints

Fingerprints are sometimes a problem on highly polished surfaces of stainless steel. They can be

minimized by applying a cleaner that will leave a thin oily or waxy film. To use these cleaners, simply

wipe on and remove excess with a soft dry cloth. After using, subsequent fingerprints will usually

disappear when wiped lightly with a soft cloth or with a cloth containing a little of the cleaner. If the

surface is especially dirty to start, wash first with soap or detergent and water.

Heat Tint

Straw-colored or slightly darkened areas may appear on stainless steel around the hot plates where

temperatures reach 500°F (260°C) or more. This "heat tint" is caused by a slight oxidation of the

stainless steel and is not harmful. To control or minimize this condition, never use more heat than is

absolutely necessary.

MAINTENANCE & ADJUSTMENTS

FLUE

Check the flue when it is cool to be sure it is free of obstructions.

SERVICE AND PARTS INFORMATION

To obtain service and parts information, contact an authorized service agency in your area (refer to our

website, www.vulcanhart.com for a complete listing of authorized service and parts depots). When

- 8 -

calling for service, the following information must be available: model number, serial number, and gas

type. This information can be found on the main data plate, located on the side of the unit.

PRECAUTIONS

When scraping off heavy deposits of grease or oil from stainless steel equipment, never use ordinary

steel scrapers. Particles of ordinary steel may become embedded in, or lodge on, the surface of the

stainless steel. These will rust, causing unsightly stains and possible contamination of food. If it is

necessary to scrape, use stainless steel, wood, plastic or rubber tools.

TROUBLESHOOTING

PROBLEM CAUSES / CORRECTIONS

Excessive Valve Handle Temperatures /

Sticking Top Burner Valves

Verify that oven door is closed.

If door is closed properly, call for service.

Improper ventilation.

Poor Ignition Call for service.

Pilot and Burners Will Not Light Verify that main gas supply is turned on.

Verify that burner assembly is properly installed.

Call for service.

NOTES

FORM F38202 Rev. A (07-08) PRINTED IN THE U.S.A.

MODE D’INSTALLATION ET MODE D’EMPLOI

PLAQUES CHAUFFANTES

DE LA SÉRIE VULCAN ENDURANCE

MODÈLES:

GCT12 GCT24

GCT36 GCT48

GCT60 GCT72

www.vulcanhart.com

Une division de Groupe ITW Équipement alimentaire, LLC

10405 Westlake Drive

Charlotte, NC 28273

DOCUMENT À CONSERVER EN CAS DE BESOIN

F38202 Rév. A (07-08)

MESURES DE SÉCURITÉ IMPORTANTES

CE MANUEL A ÉTÉ PRÉPARÉ À L’INTENTION D’UN PERSONNEL QUALIFIÉ ET AUTORISÉ À

INSTALLER DES APPAREILS FONCTIONNANT AU GAZ ET À EFFECTUER LE DÉMARRAGE

INITIAL CHEZ LE CLIENT DE MÊME QUE LE RÉGLAGE DES APPAREILS CONCERNÉS DANS

CE MANUEL.

AFFICHER À UN ENDROIT VISIBLE LES PREMIERS SOINS À ADMINISTRER À TOUTE

PERSONNE AYANT RESPIRÉ LES GAZ QUE CET APPAREIL DÉGAGE. ON PEUT SE

PROCURER CES INFORMATIONS CHEZ LE FOURNISSEUR DE GAZ LE PLUS PRÈS.

IMPORTANT

En cas d’odeurs de gaz, éteindre l’appareil par le robinet

d’arrêt principal et communiquer avec la compagnie de

gaz la plus près ou avec le fournisseur de gaz attitré pour

l’entretien.

MESURE DE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence ni autres vapeurs

ou liquides inflammables à proximité de cet appareil ou de

tout autre appareil.

L’installation, le réglage, la modification, la réparation ou

l’entretien incorrects de cet appareil peuvent causer des

dommages matériels, des blessures ou la mort. Lire

attentivement les instructions d’installation, de

fonctionnement et d’entretien avant de procéder à son

installation ou entretien.

EN CAS DE PANNE DE COURANT, NE PAS FAIRE

FONCTIONNER CET APPAREIL.

- 2 -

Page is loading ...

Vulcan-Hart GCT60 User manual

Brand: Vulcan-Hart

Model: GCT60

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Vulcan-Hart GCT60 Manuel utilisateur

Vulcan-Hart GCT60 User manual

This manual is also suitable for

Vulcan-Hart GCT60 User manual

in other languages

Related papers

Other documents