S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C– 40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
This VELLO product is warranted to the original purchaser to be free from defects in materials and
workmanship under normal consumer use for a period of one (1) year from the original purchase
date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s respon
-
sibility with respect to this limited warranty shall be limited solely to repair or replacement, at the
provider’s discretion, of any product that fails during normal use of this product in its intended
manner and in its intended environment. Inoperability of the product or part(s) shall be deter
-
mined by the warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration,
abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PRO
-
VIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO ANY IMPLIED WARRANY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. This warranty provides you with specic legal rights, and you may also have additional
rights that vary from state to state.
To obtain warranty coverage, contact the Vello Customer Service Department to obtain a return
merchandise authorization (“RMA”) number, and return the defective product to Vello along with
the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s
own risk and expense.
For more information, or to arrange service, visit www.vellogear.com or call Customer Service at
212-594-2353.
Vello is a Gradus Group Brand. Product warranty provided by the Gradus Group.
www.gradusgroup.com
Vello is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved
S
2S
ENTER
MENU
DISP
PRINT
IR
Remote
Display
Control
for Sony
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-STV infrared remote
control. This wireless remote lets you take photos, shoot video, print images,
and control playback on your Sony DSLR or NEX camera from up to fteen
feet away. The Vello IR-STV is especially useful for preventing camera shake
during long exposures and for taking self-portraits. It can also be used to
trigger a remote camera when shooting events.
Precautions
Before using your Vello IR-STV infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent it from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
• Do not clean this product with agents containing corrosive or ammable
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into a
re, as this can cause the batteries to leak corrosive liquids, generate heat,
or explode.
Overview
* These controls perform the same function as their on-camera equivalents.
Note: Except for the S, S2, and Video buttons, the buttons will work only
when the camera is plugged into a TV.
Using Your IR-STV as a Remote Trigger
The Vello IR-STV can trigger your camera’s shutter from up to fteen feet
away. To use your IR-STV as a remote trigger, turn on your camera and
follow these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter. To release the shutter with a two-second delay, press
the 2S button.
The Vello IR-STV can trigger video shooting on compatible Sony cameras. To
start shooting video, press the Video button. To stop shooting video, press
the Video button again.
Note: Please see your camera’s user manual for complete instructions and
supported features.
WIRELESS CAMERA
ACTIVATION AND
PLAYBACK
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2013 Gradus Group
Important! Because infrared technology requires line-of-sight communica-
tion between the two devices, make sure there are no obstructions
between the remote and your camera’s sensor.
Playback, Slideshow, and Printing
You can use your Vello IR-STV remote to wirelessly control playback on
your Sony camera when the camera is plugged into your TV. Most of the
buttons on the IR-STV will correspond with the buttons on your Sony
camera.
To begin a slideshow, press the slideshow button on the remote. Use the
right or left buttons on the multi-selector to display the next or previous
image, and use the ENTER button for play and pause.
To print images while viewing them on the TV, follow these steps:
1. Use an HDMI cable to connect your camera to an HDTV.
2. Plug your camera into a PictBridge-compliant printer.
3. Display the image you want to print, and then press the PRINT button on
the remote control.
For more information about the playback and printing features, consult your
camera’s manual.
Replacing the Battery
The Vello IR-STV is powered by a 3 V CR2025
lithium battery. To replace the battery, follow
these steps:
1. Use your ngernail to pry the battery tray
out of the remote.
2. Remove the old battery and replace it with a new one, making sure the
side marked with a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
Specications
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 32°F–104°F (0°C–40°C)
• Storage temperatures: -4°F–140°F (-20°C–60°C)
• Battery type: 3 V CR2025 lithium
• Dimensions: 3.6 × 1.6 × 0.4 in. (90.3 × 40.9 × 10.8 mm)
• Weight: 0.8 oz. (22.6 g)
Compatible Cameras
Sony
®
DSLR A230 / A330/ A380 / A390 / A500 / A550 / A560 / A580
DSLR A700 / A850 / A900 / SLT: A33 / 55 / A57 / A65 / A77 / NEX: 5
5n / 6 / 7
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use. To obtain
warranty coverage during the Warranty Period, contact your place of
purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number. This warranty does not extend to damage or
failure which results from misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN,
VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal
rights, and you may also have additional rights which vary from state to state.
Rotate*
Multi-Selector
Shutter Release*
Index*
Slideshow
Begins a slideshow
of images.
Enlarge
Enlarges the
selected image.
Shrink
Shrinks the
selected image.
Display*
Delete*
Menu*
Playback*
Print
Prints the selected
image on a connected
PictBridge-compliant
printer.
Shutter Two-
Second Delayed
Releases the shutter
after a two-second
delay.
Histogram
Displays histogram
onscreen.
IR-STV
CR2025
OPEN
Video Button:
Starts and stops
video shooting.
Introduction
Thank you for choosing Vello.
Congratulations on the purchase of your Vello IR-P1 infrared remote
control. This wireless remote lets you take photos and zoom in and out on
1 is especially useful
for preventing camera shake during long exposures and for taking
self-portraits. It can also be used to trigger a remote camera when shooting
events.
Precautions
Before using your Vello IR-P1 infrared remote control, please read the
following safety notices carefully and thoroughly to ensure safe use, and to
help prevent damage to your remote control or injury to yourself or others.
• Remove the battery from this product before long-term storage in order
to prevent i
t from leaking corrosive liquids.
• This product is not water resistant. Keep it away from rain, snow,
humidity, and general moisture.
substances such as paint thinner, benzene, or nail polish remover.
• Strong light and weak batteries may adversely affect the transmission of
the infrared signal.
• Dispose of used batteries properly. Never heat them or throw them into
heat, or explode.
Overview
Using Your Vello IR-P1 as a Remote Trigger
The Vello IR-P1
away. To use your IR-P1 as a remote trigger, turn on your camera and follow
these steps:
1. Remove the plastic separator from the battery.
2. Set up your shot and make sure your camera is in focus.
3. Set your camera for remote triggering. For more information about the
remote triggering feature, consult your camera’s manual.
4. Aim the remote at the camera’s infrared sensor and press the S button to
release the shutter.
Note: With compatible cameras aim the remote at the camera’s infrare
d
sensor and press the W/T button to zoom out or in.
WIRELESS SHUTTER
ACTIVATION
INFRARED
REMOTE
CONTROL
USER MANUAL
www.vellogear.com
© Copyright 2012 Gradus Group
Note: Please see your camera’s user manual for complete instructions and
supported features.
Important! Because infrared technology requires line-of-sight
communication between the two devices, make sure there are no
obstructions between the remote and your camera’s sensor.
Replacing the Battery
The Vello IR-P1 is powered by a 3 V CR2025 lithium battery. To replace the
battery, follow these steps:
1. Push the tab in the direction indicated by
the arrow in the illustration, and pull the
battery tray out of the remote.
2. Remove the old battery and replace it with a
new one, making sure the side marked with
a plus sign (+) is facing up.
3. Push the battery tray back into the remote so it locks in place.
• Operating distance: up to 15 ft. (4.6 m)
• Operating temperatures: 41°F–104°F (5°C–40°C)
• Battery type: 3 V CR2025 lithium
• Typical battery life: up to 3 years; 20,000 exposures
• Dimensions: 3.4 × 1.6 × 0.23 in. (86.3 × 40.2 × 6 mm)
• Weight: .6 oz (17 g)
Compatible Cameras
Pentax
®
K30 / K-01 / K-5 / K-5 II / K-5 IIs / K-R / Q / Q10 / X-5
Warranty
Vello provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from t
he original purchase date or thirty (30) days
after replacement whichever occurs later. Our responsibility with respect to
this limited warranty shall be limited solely to repair or replacement, at its
option, of any product which fails during normal consumer use.
To obtain warranty coverage during the Warranty Period, contact your
place of purchase (“Seller”) to obtain a return merchandise authorization
(“RMA”) number, and return to Seller the defective product along with
proof of purchase and
the RMA number. This warranty does not extend to
damage or failure which results from misuse, neglect, accident, alteration,
abuse, improper installation or maintenance. EXCEPT AS PROVIDED
HEREIN, VELLO MAKES NEITHER ANY EXPRESS WARRANTIES NOR
ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
rights, and you may also have additional rights which vary from state to
state.
S
W/T
Shutter
Release
Wide-Angle/
Telephoto
(zoom out/in)
IR-P1
CR2025
PUSH
OPEN
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
DigiCare PLS-FW50 User manual
-
Sony DSLR-A390 User manual
-
Xcellon MCO-EV6 Quick setup guide
-
-
Promaster INFRARED REMOTE CONTROL for Sony User manual
-
Sony SLT-A33 User manual
-
Promaster Infrared Remote Shutter Release for Sony Owner's manual
-
Sony SLT-A65X Operating instructions
-
Polsen HPC-A20 Closed Back Studio Monitor Headphones User manual
-
