SCOTT LSX 10 User manual

SCOTT
Brand
SCOTT
Model
LSX 10
Type
User manual

SCOTT LSX 10 is a wireless LED light with speaker. It is compatible with iDXS 10L or iXSW 50 docking stations and can be used to improve the sound system. The device can be paired with the docking station, up to two speakers per group, and assigned to a group number from 1 to 8. Once paired, the speaker can be turned on or off, and the light can be dimmed using the docking station's remote control. The speaker has an output power of 10 W (r.m.s.) and a 2.25", 4 Ohm speaker. The LED light has a power of 5W and a lifespan of 30000 hours.

SCOTT LSX 10 is a wireless LED light with speaker. It is compatible with iDXS 10L or iXSW 50 docking stations and can be used to improve the sound system. The device can be paired with the docking station, up to two speakers per group, and assigned to a group number from 1 to 8. Once paired, the speaker can be turned on or off, and the light can be dimmed using the docking station's remote control. The speaker has an output power of 10 W (r.m.s.) and a 2.25", 4 Ohm speaker. The LED light has a power of 5W and a lifespan of 30000 hours.

MODEL NO.: LSX 10
WIRELESS LED LIGHT WITH SPEAKER
Instruction Manual
GB-1
PRECAUTIONS
Follow the instructions below to ensure the product is used safely and correctly.
PLACEMENT
. Do not use the unit in places which are extremely hot, cold, dusty, or humid.
. Do not restrict the airflow around the unit by placing it in a place with poor ventilation.
. Do not place the unit close to heat sources.
. Use the apparatus only in moderate climates.
. Do not expose the unit to rain or splash with water.
. Do not place objects filled with liquids, such as vases on the unit.
AC VOLTAGE
. Before use, check that the rated voltage of your unit matches your local voltage.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with an
arrowhead symbol within
a triangle is a warning
sign alerting the user to
the presence of
“dangerous voltage”
inside the unit.
ATTENTION: To reduce the
risk of electric shock, do not
remove the cover. There are no
user serviceable parts inside
the unit. Refer all servicing to
qualified personnel.
The exclamation mark
within a triangle is a
warning sign alerting the
user to the presence of
important instructions
accompanying the
product.
Congratulations on your purchase of this additional wireless light with loud
speaker that we hope will fully meet your requirements. It will allow you to
improve iDXS 10L / iXSW 50 system.
TABLE OF CONTENTS
PRECAUTIONS 1
TABLE OF CONTENTS 1
BOX CONTENTS 2
LOCATION OF CONTROLS 2
POWER SUPPLY AND INSTALLATION 2
BASIC OPERATION 2
MAINTENANCE 3
TROUBLESHOOTING GUIDE 3
TECHNICAL SPECIFICATIONS 3
GB-2
BOX CONTENTS
1. LED Light with speaker
2. Pin for pairing
3. Instruction manual
LOCATION OF CONTROLS
LED light
with speaker
1. E27 screw
2. LED light
3. Pair button
4. Standby LED
5. Speaker
POWER SUPPLY AND INSTALLATION
LED light with speaker
Make sure the power source is switched off before installation.
Screw the LED light with speaker to an E27 socket with an AC 100-240V ~
50/60Hz power source.
Note: Do not use your external dimmer control that may cause the unit
malfunction. To dim the light, press the button repeatedly.
BASIC OPERATION
Note: This LED light with speaker must be used with the docking station -
SCOTT model no.: iDXS 10L or iXSW 50. Refer to the instruction manual of
the docking station for detail operation.
Standby/On mode
Device Standby On
LED light with
speaker
Standby LED:
LED light:
On
Off
Off
On
PAIRING
Note: Make sure that the LED light with speaker is powered properly. Refer to the
manual of your iDXS 10 L or iXSW 50 system for more information about pairing.
Pairing is to ensure your LED light with speaker can receive RF transmission
correctly from the docking station.
1. If you want to pair this new light in an existing group (one station + 2 lights to
get stereo sound), you have to reset the pairing first: when the docking station
is in standby mode, use the piece (supplied) to press and hold the PAIR button
of the docking station for more than 10 seconds until the source LEDS at the
top of the docking station flash. The station then goes back to standby mode.
2. Press the PAIR buttons briefly at the bottom of the docking station first and
then the other devices within one minute. All the standby LEDs will blink rapidly
until the pairing is successful in about one minute and the source LEDS at the
top of the docking station will flash for few seconds.
3. For pairing the next group, repeat above step (2).
GB-3
After pairing, turn on the docking station and use the number buttons (1,…8, ALL)
on the remote control of docking station to select the group of your choice and
use the or button to turn on/off the speaker sound or adjust the light of the
LED light. Note:
• For pairing, the docking station must be in standby mode and the devices must
be switched on.
• The group number is assigned according to the sequence of pairing. Number
“1” will be assigned to the first paired group.
• First and second paired speakers in the same group are set to left and right
channels respectively.
• Each group can contain maximum two sets LED light with speaker.
• In case pairing is not successful, use a sharp object to press and hold the PAIR
button more than 10 seconds at the bottom of the docking station for resetting
in standby mode. Then, repeat the pairing operation mentioned above.
MAINTENANCE
Care and maintenance
To clean the casing, unplug the unit and wipe off dust and stains with a soft,
damp cloth. Do not use benzene, thinner or similar chemicals to clean the casing.
If at any time in the future you want to dispose of this product, please
note that electrical products should not be disposed of with household
waste. Find out where your nearest recycling centre is. Consult your
local authority or retailer for more details (Waste Electrical and
Electronic Equipment Directive).
TROUBLESHOOTING GUIDE
Problems Recommendations
1. The LED light with
speaker does not work
properly
1.1 Do pairing.
1.2 Do not use your external dimmer control.
TECHNICAL SPECIFICATIONS
LED light with speaker
Power source AC 100-240V ~ 50/60Hz
Light type LED, E27 screw
Lighting power 5 W
Light life 30000 Hours
Speaker 2.25”, 4 Ohm
Output power – Speaker 10 W (r.m.s.)
Power consumption 20 W (Light + speaker)
Standby power consumption < 1 W
Dimensions 138 (H) x 85 (Dia) mm
Weight 0.4 Kg
Note: Due to continuing improvements, the technical specifications are subject
to change without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

SCOTT LSX 10 User manual

SCOTT
Brand
SCOTT
Model
LSX 10
Type
User manual

SCOTT LSX 10 is a wireless LED light with speaker. It is compatible with iDXS 10L or iXSW 50 docking stations and can be used to improve the sound system. The device can be paired with the docking station, up to two speakers per group, and assigned to a group number from 1 to 8. Once paired, the speaker can be turned on or off, and the light can be dimmed using the docking station's remote control. The speaker has an output power of 10 W (r.m.s.) and a 2.25", 4 Ohm speaker. The LED light has a power of 5W and a lifespan of 30000 hours.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents