Friedrich ES12N33B Installation guide

Type
Installation guide

This manual is also suitable for

Installation Instructions
Kühl Color Kit
For Use with Kühl and Kühl+ units
Please read these instructions completely before attempting installation.
NOTE: These instructions apply to the Friedrich Kühl Series.
Kit Contents: Quantity
Door Decorative Front (Size & Color)
1
Top Decorative Cover (Top Cover)
1
Hinge Pin
2
Tool Top Cap Removal (Screwdriver)
1
Instruction Sheet
1
Tools Required: Friedrich supplied screwdriver
Step 1. Front cover removal and install:
Please use the provided screwdriver to release top decorative cover free from unit’s decorative front.
This is accomplished by positioning the flat blade of the screwdriver into the seam (about 1” from end)
between the top cover and the decorative front. Be careful not to apply pressure to the front
horizontal louver (vents) while releasing the top cover. The top cover has 4 tab locks which hold it in
position. By inserting the blade slightly and gently twisting the tab lock can be released. Work from
the left side to the right side releasing the lock tabs until the top cover cap is loose.
Model Kühl Series
92003705_00 (5-10) Friedrich Air Conditioning Co. Page 1 of 4
Post Office Box 1540 / San Antonio, Texas 78295-1540
(210) 357-4400 / (800) 541-6645 / www.friedrich.com
TAB LOCKS (4)
NOTE: Gently slide top
cover forward
Next, with the top cover cap still in place, slide it toward you until it is free from the unit decorative
front.
Unpack the new top cover. Note that it has interlock ribs on its bottom side which will slide in to the
channels located on the top of the decorative front top surface.
Carefully align the new top cover cap interlocking rib to enter the decorative front receiving channel
and push the top cap cover to fully engage the interlock rib to the channel. Continue to push the top
cap until the locking tabs become engaged with the decorative front. The new top cover cap should
now be installed.
Step 2. Decorative front door removal and installation
Model Kühl Series
92003705_00 (5-10) Friedrich Air Conditioning Co. Page 2 of 4
Post Office Box 1540 / San Antonio, Texas 78295-1540
(210) 357-4400 / (800) 541-6645 / www.friedrich.com
Secure the interlocking rib to the
receiving channel by sliding the top
cover backward into place
The decorative front filter access door can be easily removed by utilizing the small screwdriver again.
Open the door completely and observe the hinge pins near the inside bottom left and right corners of
the door. Gently pry the hinge pin to cause it to rotate upward. Once the hinge pin is rotated clear of
the doors’ locking rib it can be removed. Gently pull the hinge pin to the side to remove it from the
door and the decorative front. With the hinges removed the door will be free to be removed from the
unit’s decorative front.
Unpack the new decorative door. New hinge pins are included with the kit and can be used if
needed.
Model Kühl Series
92003705_00 (5-10) Friedrich Air Conditioning Co. Page 3 of 4
Post Office Box 1540 / San Antonio, Texas 78295-1540
(210) 357-4400 / (800) 541-6645 / www.friedrich.com
Slide the provided screwdriver under
the hinge and pop upward to release
the hinge pin
Carefully position the new decorative door to the decorative front and while holding it in place, insert a
hinge and rotate its position to lock it into place. Next insert the other hinge pin to the opposite end
and rotate it to lock it into position.
The new decorative door is now installed.
Model Kühl Series
92003705_00 (5-10) Friedrich Air Conditioning Co. Page 4 of 4
Post Office Box 1540 / San Antonio, Texas 78295-1540
(210) 357-4400 / (800) 541-6645 / www.friedrich.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Friedrich ES12N33B Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI