822 90 22-44/rev I
HIDEAWAY MINI-KITCHEN INSTRUCTIONS
E
LECTRICAL
-
Sockets for the mini-kitchen.
A
n authorized electrician should carry out the electrical
i
nstallation. The sockets should be fitted on the wall at
the back of the sink base (see drawings). The voltage for
both the hotplates and the refrigerator is 230 - 240 V.
ASSEMBLING
F
irst unpack the base unit and position in front of the place
of installation and provide space around it for assembly.
Check that the electrical connections have been prepared
prior to the installation.
Remove the protection film from the kitchen sink plus the
three screws, (save no. 1) which hold the kitchen sink at
the back edge. Unpack the top unit. Unclip the doors and
put them aside in order not to damage them. Loosen the
six transport screws (save no. 2). Lift up the top unit and
place it on top of the base unit.
Please take extreme care, as the 3 metal runners on
the lower part of the top unit are very sharp.
W
ear heavy-duty protective gloves for this part of
the installation.
Take care not to displace the sink fitting from its position
on the bottom unit.
Place the top unit level with the front edge of the base unit.
Please note the depth of the top unit is 620 mm and the
bottom is 600 mm. Screw in the three screws that you
saved (no. 1) through the back edge profile. The six transport
screws which you saved (no. 2) should be used to attach
both of the side rails to the sink unit.
In order to do this, use a metall drill with 2,5 mm diameter
and drill through the pre bored holes in the side edge profiles
t
hrough onto the kitchen sink´s side gables.
Tighten the screws.
Remove the safety metal bar profile that is fitted between
the inner sides of the top unit at the lower front edge and
re-mount the screws.
F
INAL
A
SSEMBL
Y
•
Re-hang the doors and if needed, adjust the hinges.
• Connect the plugs in the right wall sockets and test
all functions.
• Check that the safety micro switch cuts the circuit to
the lighting and the hotplates but not to the refrigerator.
• Connect water and run through to check seals are tight.
SAFETY INSTRUCTIONS
The compact kitchen is approved by SEMKO for connection
according to the enclosed instructions. The hotplates effect
1000 W respectively 1200 W may not be increased by
exchange. The top unit has a safety switch for the hot-
plates and light / socket assembly.
The safety switch closes the circuit when the door is shut
and may not be bypassed.
ELECTRICAL INSTRUCTIONS
H
IDEA
WAY M
INI-KITCHEN WITH HOTPLA
T
ES
1
. 2 No. 13 amp sockets are required for the base unit.
1
No. 13 amp socket is required for the top unit.
(
An additional 13-amp socket may also be required for
a microwave housed within the top unit).
2. The 2 wires located at the back of the top cupboard
u
nit
m
ust
b
e connected to the control box located
under the sink (behind the controls for the hotplates).
This ensures that the circuit to the hotplates is cut off
when the upper doors are closed.
3. The blue wire already connected to the terminal block
(in the control box), must be moved over by one, to
allow the two additional wires from the top unit to be
connected. (See the attached wiring diagram).
4. The microwave can be connected to the light / socket
switch or alternatively the lead can be taken through
the back of the top unit and connected to an additional
13 amp socket. This will enable the internal 13 amp socket
switch to be used for other appliances e.g. A kettle.
5. The 13 amp plug from the top unit
must be connected
to a separate socket from the base unit, which includes
the fridge and hotplates, or any other appliance.
Do not use 2/3 way connectors or gang sockets.
The top unit should not be connected to the same phase
as the base unit.
HIDEAWAY MINI-KITCHEN WITHOUT HOTPLATES
1. 1 No. 13 amp socket is required for the refrigerator in
the base unit.
2. 1 No. 13 amp socket is required for the light / socket
switch located at the back of the cupboard unit.
(An additional 13-amp socket may also be required for
a microwave housed within the top unit).
3. The microwave can be connected to the light / socket
s
witch or alternatively the lead can be taken through
the back of the top unit and connected to an additional
13 amp socket. This will enable the internal 13 amp socket
switch to be used for other appliances e.g. A kettle.
4. The 13 amp plug from the top unit must be connected
to a separate socket from the base unit, which includes
the fridge and hotplates, or any other appliance.
Do not use 2/3 way connectors or gang sockets.
The top unit should not be connected to the same phase
as the base unit.
W
iring diagram for connecting the top cupboard to a base unit fitted with hotplates.
T
OP DIAGRAM
A
BOTTOM DIAGRAM B
Showing existing connections to be found in the control box situated behind the hotplate knobs on the base unit.
Showing the spiral hose with 2 wires located at the rear of the top cupboard.
These wires, when connected, activate the door ”cut-out” switch.
The blue wire (2) in diagram
A must be moved to a neighbouring terminal (as shown), in order that the
2 wires that activate the door switch can then be connected.
-
1
-
2
Electrolux E1000 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Parkinson Cowan SiG450WN Acclaim User manual
-
-
-
-
Zanussi ZCMiD User manual
-
-
-
-
-