Aeg-Electrolux KB9820E-M User manual

Category
Ovens
Type
User manual
KB9820E
User manual Built-in fan / steam
oven
Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Operating instructions 3
Safety information 3
Electrical safety 3
Children's safety 3
Safety during use 3
How to avoid damage to the appliance
3
Description of appliance 4
General view 4
Control panel 5
Oven layout 5
Accessories Oven 6
Before first use 6
Setting and changing the time 6
Cleaning for the first time 7
Getting to know the appliance 8
Operating the oven 8
The electronic oven controls 8
Oven Functions 11
Inserting the oven shelf and baking tray
11
Grease filter 12
Steam cooking functions 12
Additional functions 14
Clock functions 15
Other functions 20
Uses, charts and tips 21
Cooking with Steam 21
Baking 25
Roasting 31
Low temperature cooking 32
Single economy grill 33
Rotitherm Roasting 33
Defrosting 34
Drying 35
Making preserves 35
Programmed functions and recipes 36
Cleaning and care 42
The outside of the appliance 42
Oven interior 42
Accessories 43
Grease filter 43
Side rails 43
Steam generation system 45
Oven lighting 45
Oven door 46
What to do if ... 47
Installation instructions 48
Safety instructions for the installer 49
Disposal 53
Packaging material 53
Service 53
European Guarantee 53
www.electrolux.com 54
Subject to change without notice
2
Contents
Operating instructions
Safety information
Important safety instructions!
Read carefully and keep for future use!
Electrical safety
This appliance must only be connected by a qualified installation engineer .
In the event of a fault or damage to the appliance: Take the fuses out or switch off.
Repairs to the appliance must only be carried out by qualified service engineers .
Considerable danger may result from improper repairs. If repairs become necessary,
please contact our Customer Care Department or your dealer.
Children's safety
Never leave children unsupervised while the appliance is operating.
This appliance is fitted with a child safety device.
Safety during use
This appliance should be used only for normal domestic cooking, roasting and baking of
food.
Be careful if connecting electrical appliances to sockets near to this appliance. Electrical
leads must not be caught under the hot oven door.
Warning: Risk of burns! The interior surfaces of the oven become very hot during use.
Warning: Do not under any circumstances open the oven door during steam
cooking. The escaping steam can cause moisture damage to units. Avoid any direct
contact with the escaping steam.
If you use ingredients containing alcohol in the oven, a slightly flammable mixture of
alcohol and air may ensue. In this case, be careful when opening the door. Do not handle
any sources of heat, sparks or naked flames when doing so.
People (including children), who, because of their physical, sensory or mental capabilities
or their inexperience or ignorance, are not able to use the appliance safely, should not
use this appliance without supervision by or instruction from a responsible person.
Information on acrylamides
According to the latest scientific knowledge, intensive browning of food, especially in
products containing starch, can constitute a health risk due to acrylamides. Therefore we
recommend cooking at the lowest possible temperatures and not browning foods too much.
How to avoid damage to the appliance
Do not line the oven with aluminium foil and do not place a baking tray or saucepan
etc. on the floor, as otherwise the oven enamel will be damaged by the heat build-up.
Fruit juices dripping from the baking tray will leave stains, which you will not be able to
remove. For very moist cakes, use a deep tray.
Do not put any strain on the oven door when open.
Never pour water directly into the oven when it is hot. This could cause damage to and
discoloration of the enamel.
Safety information
3
Rough handling, especially around the edges of the front panel, can cause the glass to
break.
Do not store any flammable materials inside the oven. These could ignite when the oven
is switched on.
Do not store any moist foods inside the oven. This could cause damage to the enamel.
Do not leave dishes uncovered in the oven after switching off the cooling fan. Moisture
may form inside the oven or on the glass door and also get onto the units.
Information on the oven enamel
Changes to the colour of the oven's enamel surface as a result of use do not affect the
appliance's suitability for normal and correct use. They therefore do not constitute a defect
in terms of warranty law.
Description of appliance
General view
1
2
3
1 Control panel
2 Door handle
3 Full glass door
4
Description of appliance
Control panel
1
2
3
1 Oven displays
2 Oven function buttons
3 Water drawer
Oven layout
1
6
5
7
1
2
3
2
3
4
1 Grill element
2 Light in the oven
3 Grease filter
4 Rear wall heating element fan
5 Steam generator/Steam rosette
Description of appliance
5
6 Side rails, removable
7 Oven shelf levels
Accessories Oven
Shelf
For cookware, cake tins, roasts and grilling food.
Baking tray
For cakes and biscuits.
Patisserie tray
For rolls, brezels and small pastries.
Can be use for steam function. Discoloration of
the surface has no impact on function.
Quick Sponge 180
Extremely absorbent sponge for absorbing any re-
sidual water from the steam generator.
Before first use
Setting and changing the time
The oven only works when the time has been set.
6
Before first use
When the appliance has been connected to the
electrical supply or when there has been a power
cut, the time symbol
flashes automatically.
1. To change a time of day that has already been
set, press the clock function
button re-
peatedly until the time symbol
flashes.
2. Use the
or button to set the current
time.
After approx. 5 seconds, the flashing stops and the
clock displays the time of day set.
The appliance is now ready to use.
The time can only be modified if the child safety
device is deactivated, none of the clock functions
Countdown
, Cook time or End and no
oven function is set.
Cleaning for the first time
Before you use the oven for the first time, you should clean it thoroughly.
Do not use any sharp or abrasive cleaning tools or materials! These could damage the
surface.
For metal fronts, use normal commercially available cleaning agents.
1. Open the oven door.
The lighting in the oven is switched on.
2. Remove all accessories and side rails and clean with a warm solution of water and
washing-up liquid.
3. Also wipe the oven out with a warm solution of water and washing-up liquid and then
dry it.
4. Wipe the front of the appliance with a damp cloth.
Before first use
7
Getting to know the appliance
The appliance can be operated in test mode for testing or performing all operating steps.
The oven is not heating up.
Switching test mode on
1.
Switch off the appliance using the on/off
button .
2. Press and hold baking/roasting programme
buttons
and at the same time until an
acoustic signal sounds and "d" lights in the
display.
Switching test mode off
1.
Switch off the appliance using the on/off
button .
2. Press and hold baking/roasting programme
buttons
and at the same time until an acoustic signal sounds and "d" goes out
in the display.
Operating the oven
The electronic oven controls
The display field
1 2 3 4
567
1 Memory: P / Test: d
2 Steam mode
3 Temperature/Time
4 Clock functions/Operating time
5 Thermometer symbol
6 Baking/Roasting programmes
7 Oven functions
8
Operating the oven
Control panel
1
2
3
6
5 4
1 On/Off
2 Baking/Roasting programmes
3 +/- button
4 Clock functions
5 Memory function
6 Oven function selection
General notes
Always switch on the appliance first using the On/Off
button.
When the selected function is lit, the oven begins to heat up or the set time begins to
count down.
When the selected temperature is reached, a signal sounds.
The oven light is switched on as soon as an oven function is started or the oven door is
opened.
If the door is open and the appliance is switched off, the oven light goes off after 10
minutes.
Switch off the appliance using the On/Off
button.
Selecting an oven function
1. Switch on the appliance using the On/Off
button.
Operating the oven
9
2. Press the or button repeatedly until
the desired oven function appears.
A suggested temperature appears in the
temperature display.
If the suggested temperature is not
changed within approx. 5 seconds, the oven
begins to heat up.
Changing the oven temperature
Press the
or button to raise or lower the
temperature.
The setting changes in 5°C steps.
Thermometer symbol
The slowly rising thermometer symbol
indicates how far the oven has heated up.
The three segments of the thermometer symbol
flashing one after the other show that
Fast Warm Up is on.
Changing the oven function
To change the oven function press the
or
button until the function you want is displayed.
10
Operating the oven
Switching the oven off
Switch off the appliance using the On/Off
but-
ton.
Cooling fan
The fan switches on automatically to keep the ap-
pliance surfaces cool. When the oven is switched
off, the fan continues to run to cool the appliance
down and then switches itself off.
Oven Functions
Oven functions Use
Steam Cooking
For vegetables, potatoes, rice, pasta or other side-dishes.
Interval Steam Cook-
ing
For baking, roasting and warming up chilled and frozen
meals.
Ventitherm ® Fan Op-
erated Cooking
For roasting and baking on up to two levels at the same
time.
Rotitherm Roasting For roasting larger pieces of meat or poultry on one level.
The function is suitable for gratinating and browning .
Single Economy Grill For grilling flat foodstuffs and for toasting .
Defrost/Drying For defrosting and drying herbs, fruit and vegetables.
Low temperature
cooking
For preparing particularly tender and succulent roasts.
Moist Fan Cooking
For energy-saving baking and cooking of mainly dry bakery
items as well as for baking in tins on one level.
Inserting the oven shelf and baking tray
Shelf runner safety and anti-tip device
To increase shelf runner safety, all insertable components have a small curved indentation
at the bottom on the right and left-hand edge.
Always insert insertable components so that this indentation is at the back of the oven
interior. This indentation is also important for preventing the insertable components from
tipping.
Operating the oven
11
Baking tray :
Push the baking tray between the guide bars of
the selected oven level.
Oven shelf :
Insert the oven shelf so that the feet point down-
wards.
Push the oven shelf between the guide bars of
the selected oven level.
The high rim around the oven shelf is an addi-
tional device to prevent cookware from slipping
off.
Grease filter
Only use the grease filter when roasting to
protect the rear heating elements from fat
splashes.
Inserting the grease filter
Hold the grease filter by the tab and insert the
two mounts downwards into the opening on the
rear wall of the oven (fan opening)
Removing the grease filter
Hold the grease filter by the tab, unhook it and
lift out.
Steam cooking functions
The steam cooking functions must always be set in conjunction with the clock functions
Cooking Time
or End Time (see chapter Clock Functions Cooking Time / End Time
).
12
Operating the oven
Only water can be used as the liquid.
A buzzing tone is heard when the water has been used up. The buzzing tone switches off
again shortly after the water is refilled.
Due to the automatic steam dispersal period of about 5 minutes at the end of the cooking
time and the heating up time of approx. 2 minutes, settings under 10 minutes have little
effect.
Steam will continue to escape when the door is opened.
Steam cooking
1. Do not fill the water (approx. 650 ml) di-
rectly into the steam generator, but into
the water drawer in the control panel.
The water supply lasts for approx. 30 mi-
nutes.
2. Switch the oven on using the On/Off
button.
3. Using the
or button, select the
steam cooking function
and using
the
or button, set the desired tem-
perature (range 50°C - 96°C).
4. Using the clock functions button
, se-
lect the cooking time
or end time
function and using the or button,
set the desired cooking time or switch-off
time you want. After approx. 2 minutes,
the first steam appears. A single audible
signal indicates when the cooking tem-
perature of approx. 96°C is reached.
A triple acoustic signal indicates the end of cooking time.
5. Stop the signal and switch off the oven by pressing the On/Off
button.
After the oven has cooled down, soak up any remaining water from the steam generator
using a sponge and, if necessary, wipe with a few drops of vinegar.
Leave the door open to let the oven dry completely.
Interval cooking
The continual change from hot air to steam takes place automatically.
1. Do not fill the water (approx. 250 ml) directly into the steam generator, but into the
water drawer in the control panel.
2. Switch the oven on using the On/Off
button.
Operating the oven
13
3. Using the or button, select the interval cooking function and using the
or button, set the desired temperature.
4. Using the clock functions button
, se-
lect the cooking time
or end time
function and using the or button,
set the desired cooking time or switch-off
time you want.
Then proceed as for steam cooking
.
Additional functions
Baking/Roasting programmes
Use the given recipes for this function.
Selecting the programme
1. Switch the oven on using the On/Off
button. Press the baking/roasting pro-
gramme button
, then keep pressing
the
or button until the programme
you want (P1 to P12) appears in the dis-
play.
The symbol for the corresponding oven
function appears in the function dis-
play.
The cooking time appears in the clock
display, the cooking time symbol
lights up.
Press the clock functions
button, then press the or button, to change the
cooking time.
After approx. 5 seconds, the oven switches itself on.
2. When the time has elapsed, a signal sounds for 2 minutes. The symbol for cooking time
flashes.
The oven switches itself off.
3. The signal can be stopped by pressing any button.
Delaying the start
The start of the cooking time can be delayed (see Clock Function end time
).
Ending cooking time early
Switch the oven on using the On/Off
button.
Memory function
The Memory function can be used to save one setting which is used very frequently.
1. Set oven function, temperature and if necessary the clock functions Cooking Time
and/or End Time .
14
Operating the oven
2. Press and hold the Memory function
button for approx. 2 seconds until a signal
sounds. The setting is saved.
To save another setting, press and hold the
Memory function
button again for approx.
2 seconds. The previously saved setting is re-
placed by the new one.
Starting the Memory function
1. Switch the oven on using the On/Off
but-
ton.
2. Use the memory function
button to call up
the saved setting.
Clock functions
1
2
3
4
5
6
1 Clock functions
2 Clock displays
Operating the oven
15
3 Time
4 Cook Time/End Time/Operating Time
5 Clock functions
6 Selector buttons
Countdown
To set a countdown. When it has counted down, a signal sounds.
This function has no effect on the oven.
Cooking time
To set how long the oven is to operate.
End time
For setting when the oven is to switch itself off again.
Time
To set, change or find out the time (see section Before using for the first time).
General instructions
After a clock function has been selected, the corresponding symbol flashes for about 5
seconds. During this period, the desired times can be set or modified using the
or
button.
When the desired time has been set, the symbol continues to flash for approx. 5 seconds.
After this the symbol lights up. The set countdown
begins.
The time set for cooking time
and end time begins to count down after the selected
function starts.
Countdown
1. Press the clock function button re-
peatedly until the countdown symbol
flashes.
2. Using the
or button set the desired
countdown (max. 99.00 minutes).
16
Operating the oven
After approx. 5 seconds the display shows the time
remaining. The countdown symbol
lights up.
When the time has elapsed, a signal sounds for 2
minutes. "0.00" lights up and the countdown sym-
bol
flashes.
To turn off the signal: Press any button.
Cooking time
1. Select the oven function and temperature
using the
or button.
2. Press the clock function button
re-
peatedly until the cooking time symbol
flashes.
3. Using the
or button, set the desired
cooking time.
Operating the oven
17
The oven switches itself on. The symbol for cooking
time
lights up.
Press the clock functions button repeatedly to
check the current time.
When the time has elapsed, a signal sounds for 2
minutes. The oven switches itself off.
"0.00" appears and the cooking time symbol
flashes.
To turn off the signal: Press any button.
End Time
1. Select the oven function and temperature
using the
or button.
2. Press the clock functions button
re-
peatedly until the end time symbol
flashes.
3. Using the
or button, set the desired
switch-off time.
18
Operating the oven
The symbols for end time and cooking time
light up.
The oven switches itself on automatically.
Press the clock functions button repeatedly to
check the current time.
When the time has elapsed, a signal sounds for 2
minutes. The oven switches itself off.
"0.00" appears and the symbols for end time
and cooking time flash.
To turn off the signal: Press any button.
Setting both cooking time
and end time
Cooking time and end time can be used simultaneously, if the oven is to be switched
on and off automatically at a later time .
1. Select oven function and temperature.
2. Using the cooking time
function, set
the time required for cooking the dish,
e. g. 1 hour.
3. Using the end time
function, set the
time at which the dish is to be ready,
e. g. at 14:05.
Operating the oven
19
The symbols for cooking time and end time
light up.
The oven switches itself on automatically at the
time calculated, e. g. at 13:05.
When the set cook time has elapsed, a signal
sounds for 2 minutes and the oven switches itself
off, e. g. at 14:05.
Other functions
Switching off the display
You can save energy by switching off the display.
Switching off the display
1. Switch off the appliance using the On/Off
button. Residual heat must not be dis-
played.
2. Press the clock buttons
and at the
same time until the display goes dark.
As soon as the appliance is operated again, the
display automatically switches itself on. When
the appliance is next switched off, the display
goes out again.
To have the time permanently displayed again,
you must switch the display on again.
Switching on the display
1. Switch off the appliance using the On/Off
button.
2. Press the clock buttons
and at the same time until the display lights up again.
Child lock
As soon as the child lock is activated, it is no longer possible to operate the oven.
Switching on the child lock
1. Switch off the appliance using the On/Off
button. No oven function may be se-
lected.
2. Press and hold the baking/boasting pro-
gramme buttons
and at the same
time, until SAFE appears in the display.
The child lock is now on.
Switch off the child lock
1. Switch off the appliance using the On/Off
button.
20
Operating the oven
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Aeg-Electrolux KB9820E-M User manual

Category
Ovens
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI