Eizo FDU2603WT User manual

Important

• Please read the Precautions and this User’s Manual carefully to

familiarize yourself with safe and effective usage.

• The software described in this document is provided based on the

Software License Agreement, and can be used only when you agree

with the contents of the agreement.

• This document exclusively describes the projected capacitive touch

panel monitor.

• For information about how to connect the monitor, refer to the Setup

Manual of your monitor.

• The latest software and User’s Manual are available for download

from our web site:

http://www.eizoglobal.com

User’ s Manual

Touch Panel Setting Tool

2

About This Document

1. EIZO Corporation shall retain the copyright to this document. Reprinting this document in part or

in whole without prior permission from EIZO Corporation is strictly prohibited.

2. The contents of this document are subject to change without notice.

3. While we take great care in producing this document, if you nd any errors or omissions, please

contact EIZO.

4. Notwithstanding the above, EIZO shall not assume any responsibility for damages, loss of prots,

and the like, resulting from the use of this document.

Windows, .NET Framework are registered trademarks of Microsoft Corporation in the United States and

other countries.

DMT-DD is a registered trademark of DMC Co, Ltd.

EIZO and the EIZO logo are registered trademarks of EIZO Corporation in Japan and other countries.

Other company and product names are trademarks or registered trademarks of their respective companies.

About This Document

This document describes the procedures required to operate the EIZO projected capacitive touch panel

monitor in Windows 10 / Windows 8.1 / Windows 7.

About DMT-DD

DMT-DD is the software used to operate EIZO touch panel monitors in Windows 10 / Windows 8.1 / Windows 7.

The available operating system varies depending on the model you are using. For details, refer to the User’s

Manual of the model you are using.

3

Contents

3-11. Tool Setting .................................................. 35

●

Resident Function ......................................... 35

Chapter 4 Troubleshooting .............................. 36

Chapter 5 Reference Information ................... 38

5-1. Uninstalling the Touch Panel Driver ......... 38

●

USB Connection............................................ 38

●

COM Port Connection ................................... 38

5-2. Uninstalling DMT-DD .................................. 40

Contents

About This Document ........................................... 2

About DMT- DD ....................................................... 2

Contents ................................................................. 3

Chapter 1 Introduction ....................................... 4

1-1. Outline ............................................................ 4

●

Operating Conditions ...................................... 4

1-2. Precautions ................................................... 4

Chapter 2 Setup .................................................. 5

2-1. Setup Flow ..................................................... 5

2-2. Installing DMT-DD ......................................... 6

2-3. Installing the Touch Panel Driver ................ 8

●

Installing the Touch Panel Driver (USB

Connection) ..................................................... 9

●

Installing the Touch Panel Driver (COM

Port Connection) ............................................. 9

2-4. ConguringaTouchPanel .........................12

2-5. RegisteringaCongurationFile ................14

2-6. Calibrating the Touch Panel Monitor .........17

2-7. Calibrating the Sensitivity of the Touch

Panel Monitor ...............................................18

Chapter 3 Touch Screen Properties ............... 19

3-1. Touch Panel Device List ............................. 20

3-2. Software Settings ........................................21

●

Software Settings .......................................... 22

●

Calibration ..................................................... 23

3-3. Touch Input Setting .................................... 25

●

Touch Input .................................................... 25

●

Touch Form ................................................... 26

●

Lift-off Delay .................................................. 26

●

Touch Enabled .............................................. 26

●

Inversion ........................................................ 26

3-4. Touch Sound................................................ 27

●

Play Type ....................................................... 27

●

Sound Timing ................................................ 28

●

Beep Setting .................................................. 28

●

Name of the le to play ................................. 28

3-5. Right-click .................................................... 29

3-6. Hardware Setting ........................................ 30

3-7. Hardware Information .................................31

3-8. CongurationFile ....................................... 32

●

Conguration File .......................................... 32

●

Addition and Deletion of Conguration File .. 32

●

Default Setting ............................................... 33

3-9. Touch Setting .............................................. 33

3-10. Mouse Setting ............................................. 34

4

Chapter 1 Introduction

1-1. Outline

DMT-DD provides the functions necessary to operate a touch panel. The functions are as follows:

• Install and Uninstall of the touch panel driver

• Conguration of the touch panel driver

●

Operating Conditions

The following shows the conditions that need to be satised to operate DMT-DD on the EIZO

projected capacitive touch panel monitor.

OS • Windows 10 (32 bit / 64 bit)

• Windows 8.1 (32 bit / 64 bit)

• Windows 7 (32 bit / 64 bit)

Software .Net Framework 3.5

Hard disk Approximately 10MB of free space / data le capacity on the system drive

Interface • USB

• RS-232C (COM port connection)

Attention

• The available operating system varies depending on the model you are using. For details, refer to the User’s

Manual of the model you are using.

• System-builder version of Windows 8.1 / Windows 10 is not supported.

Note

• “(Limited) Touch Support” may be indicated in the system properties, however, this does not affect the

operation of the touch panel.

1-2. Precautions

• If this software is used under the following conditions, the software may not operate properly.

- Usage methods that are different from the instructions contained in this document

- Usage in operating conditions other than those specied

- Usage in an environment where mouse emulation software or any similarly functioning software is

installed

- Using after installing the software by overwriting a previous version

• EIZO shall not be liable in any way for any issues that may arise from using this software. Be sure to

back up your system before installing this software.

5

Chapter 2 Setup

2-1. Setup Flow

1. Connecting the product

• Refer to the Setup Manual of your model.

2. Starting the computer

3. Installing DMT-DD (page 6)

4. Installing the touch panel driver (page 8)

5. Conguring the touch panel (page 12)

6. Registering the conguration le (page 14)

7. Calibrating the touch positions (page 17)

Completion

6

Chapter 2 Setup

2-2. Installing DMT-DD

Attention

• If you need to re-install DMT-DD, e.g. when upgrading, uninstall DMT-DD rst. Then restart your PC and install

DMT-DD.

1.

Log in to the computer using an account that has administrator privileges.

For information on user account privilege settings, contact your system administrator.

2.

Insert the "EIZO LCD Utility Disk" into the optical disk drive.

3.

Open the "Touch Panel" tab, and under "Touch Panel Driver", click "Install".

The “Welcome to the DMT-DD Setup Wizard” window will appear.

Note

• To perform installation by downloading DMT-DD from our website, carry out the following procedure.

1. Extract the downloaded le.

2. Double-click “DMT-DDSetup.msi” (Windows 8.1 / Windows 7) or “DMT-DDSetup_ms.msi” (Windows 10).

Attention

• If an installer other than the installer dedicated to the OS used is executed, a message appears and

installation fails. Be sure to execute the dedicated installer.

7

Chapter 2 Setup

4.

Install the software in accordance with the on-screen instructions.

Note

• During the installation procedure, the following screen may appear several times. If so, click on “Install”.

5.

Click “Close”.

Installation is completed at this point. If DMT-DD was installed successfully, a shortcut is created on

the desktop.

8

Chapter 2 Setup

2-3. Installing the Touch Panel Driver

Merely installing DMT-DD does not enable the touch panel to function. You must install the driver in each

touch panel monitor. The installation procedure differs depending on the method used to connect the

touch panel.

Attention

• You must have local administrative privileges for the user account. For information on user account privilege

settings, contact your system administrator.

• Depending on the user account control settings, the following window may appear. Click “Yes”.

Note

• When you add or change a touch panel monitor to be connected to your computer, you need to install a driver for

the touch panel monitor.

• The installation method of the touch panel driver differs depending on the connection cable.

- For details on the installation procedure for “COM port connection” that uses an RS-232C cable, refer to

"Installing the Touch Panel Driver (COM Port Connection)" (page 9).

- For details on the installation procedure for “USB connection” that uses a USB cable, refer to "Installing the

Touch Panel Driver (USB Connection)" (page 9).

• The COM port connection and the USB connection cannot be used at the same time on the same touch panel

monitor.

9

Chapter 2 Setup

●

Installing the Touch Panel Driver (USB Connection)

The touch panel driver will be installed automatically when a USB cable is connected after DMT-DD

is installed. If the USB cable is already connected before installing DMT-DD, disconnect and connect

the USB cable again, or click “Install”.

Attention

• After the installation procedure is completed, you must reboot the computer.

●

Installing the Touch Panel Driver (COM Port Connection)

1.

Check if the signal cable is properly connected.

2.

Launch DMT-DD.

3.

From the “Touch Panel Device List”, select the icon of the touch panel to which

the touch panel driver is to be installed.

Note

• Touch the screen of the monitor to which the touch panel driver is to be installed, then the icon connected

with the monitor that you touched will be selected.

10

Chapter 2 Setup

4.

Click “Install”.

Attention

• When you click “Install”, a message may appear.

• Check the following points, then click “Install” again.

- Uncheck “Disabled COM port search” if it is checked.

- Check that the RS-232C cable is properly connected.

The conrmation window will appear.

11

Chapter 2 Setup

5.

Click “Yes”.

Installation will start.

Note

• If the driver is being installed for the rst time, the following window will appear several times. Click “Install”.

When the installation procedure is completed, a message will appear.

6.

Click “OK”.

Installation is completed at this point.

When the installation procedure has been completed successfully, the icon in the “Touch Panel

Device List” will change to the “Installed” icon.

7.

Reboot the computer.

12

Chapter 2 Setup

2-4. ConguringaTouchPanel

Associate the touch panel device (USB connection or COM port connection) with the monitor (video

signal cable connection such as DVI and D-Sub).

Attention

• If you replace the monitor or change the COM port or USB port used to connect the monitor, you will need to run

“Monitor conguration” from “Device Addition”.

• If you have changed any display setting(s) of the monitor (expansion or reproduction display, or aspect ratio), you

will need to run “Monitor conguration”.

1.

In“DeviceAddition”,clickthe“Monitorconguration”button.

The following window will appear on the rst monitor.

Touch the touch screen of this monitor twice consecutively.

If you want to proceed to set the next monitor, press the Enter button.

If you want to cancel, press the ESC button.

The driver con󲻻gured on this monitor will be indicated below.

If the monitor displaying this window is not a touch panel monitor, press “Enter” on the keyboard. The

window shown above moves to the next monitor to the right. Repeat this until the window is displayed

on the relevant touch panel monitor.

To cancel the setting, press “Esc” on the keyboard.

13

Chapter 2 Setup

2.

Touch the touch panel twice.

The touch panel device is associated with the monitor, and the display on the touch panel monitor

changes to the following window.

Touch the touch screen of this monitor twice consecutively.

If you want to proceed to set the next monitor, press the Enter button.

If you want to cancel, press the ESC button.

The driver con󲻻gured on this monitor will be indicated below.

　(1) ROOT\HIDCLASS\0001

Note

• Displayed contents differ depending on the environment.

3.

Close the selection window.

Press “Enter” on the keyboard.

4.

Reboot the computer.

14

Chapter 2 Setup

2-5. RegisteringaCongurationFile

If you register a conguration le, you can congure the operation mode of the touch panel.

Attention

• You must register a conguration le for each installed touch panel driver.

• In the default setting, no conguration le is registered. When no conguration le is registered, the “Touch.mfd”

le will be set.

1.

In “Basic Setting” - “Device Select”, select the touch panel driver for which a

congurationleistoberegistered.

2.

Inthe"CongurationFile"tab,selectaleaccordingtotheinputmethodfrom

the"CongurationFile"pull-downmenu.

Touch digitizer mode

(Touch.mfd)

Mouse emulation mode

(Mouse.mfd)

Two or more simultaneous touch points are available.

*1

Only single point touch is available.

Enables the same operations as those of the mouse as well as multi-

touch operations such as image zoom and rotation.

The cursor reacts in the same way

when you operate the mouse.

*1 The allowable number of simultaneous touch points varies depending on the monitor you are using. For

details, see the User’s Manual of the monitor.

Note

• The “Conguration File” is not registered by default. If the conguration le is not registered, the touch

digitizer mode (“Touch.mfd” le) is selected. When you want to use mouse emulation mode, select the “Mouse.

mfd” le.

15

Chapter 2 Setup

3.

Click “Register”.

A message will appear, indicating that the setting has been completed.

If you select "Touch.mfd", execute the following steps.

4.

In “Touch Settings” - “Tablet PC Settings”, click “Open”.

The windows standard “Tablet PC Settings” window will appear.

5.

Selectthe“Display”tab,andunder“Congure”,click“Setup”.

The following window will appear on the rst monitor.

Touch this screen to identity it as the touchscreen.

If this is not the Tablet PC screen, press Enter to move to the next screen.

To close the tool, press Esc.

If the monitor displaying this window is not a touch panel monitor, press “Enter” on the keyboard. The

window shown above moves to the next monitor to the right. Repeat this until the window is displayed

on the relevant touch panel monitor.

To cancel the setting, press “Esc” on the keyboard.

When the setting is completed, the message window is closed, and the display returns to the "Tablet

PC Settings".

16

Chapter 2 Setup

6.

Display "Touch Panel Setting Tool", and open "Basic Setting" - "Touch Input

Setting".

7.

Specify "Touch Data Mode" to suit the operating system you are using.

Setting Description

Serial Mode (default setting) Select this mode if you are using Windows 8.1 or an earlier operating system.

Hybrid Mode Select this mode if you are using Windows 10 or a later operating system.

8.

After selecting the touch data mode, click “Entry”.

The touch data mode is specied.

9.

Reboot the computer.

17

Chapter 2 Setup

2-6. Calibrating the Touch Panel Monitor

Calibrate the touch panel monitor to align the touched positions with the positions at which the cursor is

displayed in response to each touch.

1.

In “Basic Setting” - “Device Select”, select the touch panel monitor on which

positions are to be calibrated.

2.

Click “4Point” or “9Point” in the “Software Setting” tab.

The calibration window will appear.

3.

Touch the center of the marker displayed in the window.

Tap the each cross on the screen as it appeared in order to input

a calibration sample.

If you want to stop inputting a calibration sample,

press the ESC button.

Do you change the display orientation until calibration is completed.

Touching the marker causes the next marker to appear. Touch the center of the new marker.

When all the markers are touched, the calibration is completed. The conrmation window will appear.

4.

Click “OK”.

The position calibration is completed at this point.

18

Chapter 2 Setup

2-7. Calibrating the Sensitivity of the Touch Panel

Monitor

Calibrate the sensitivity of the touch panel monitor.

1.

In "Basic Setting" - "Device Select", select the touch panel monitor you want

to calibrate the sensitivity for.

2.

Click "Open" in the "Hardware Setting" tab.

The sensitivity calibration window will appear.

When the sensitivity calibration window is closed, calibration is completed.

19

Chapter 3 Touch Screen Properties

When you launch DMT-DD, the “Touch Screen Properties” window will appear.

Using the “Touch Screen Properties”, you can congure the operation settings and calibrate the touch panel.

20

Chapter 3 Touch Screen Properties

3-1. Touch Panel Device List

If you click “Device Addition”, icons of USB connected touch panels, connectable COM ports, or

installed touch panels are displayed in the “Touch Panel Device List”.

Note

• When you connect or disconnect a USB connected touch panel, the “Touch Panel Device List” will be

updated automatically.

• Click “List Update” to update the “Touch Panel Device List”.

• If you check “Disabled COM port search”, touch panels connected to COM ports will not be searched.

This check box is unchecked by default. If you uncheck this, touch panels connected to COM ports will be

searched automatically.

• The “Touch panel device list” is not automatically updated when installing or uninstalling the touch panel

driver.

• The icons will appear as below.

Icon

Connection

Type

Unconnected COM Port COM Port USB Port

*1

USB Port

Touch Panel

Driver

- Before installation After installation Before installation After installation

Status

- - √ - √

√ : They can be used as a touch panel monitor.

*1 This icon appears if the touch panel monitor has been connected via USB before installing DMT-

DD. The driver will be installed by selecting the icon then clicking “Install”, or by disconnecting and

connecting the USB cable again.

Page is loading ...

Eizo FDU2603WT User manual

Eizo FDU2603WT User manual

Related papers

Other documents