The Miller JK000000 Cross Slide is a versatile and durable piece of equipment designed to provide horizontal or vertical movement for welding equipment. With a total slide movement of 4 inches and a weight capacity of 8 lbs. 12 oz., this cross slide can accommodate a wide range of welding equipment and accessories. The included loading curve ensures that the equipment is properly balanced and safe to operate. Installation is simple, with pre-drilled mounting holes and supplied hardware.
The Miller JK000000 Cross Slide is a versatile and durable piece of equipment designed to provide horizontal or vertical movement for welding equipment. With a total slide movement of 4 inches and a weight capacity of 8 lbs. 12 oz., this cross slide can accommodate a wide range of welding equipment and accessories. The included loading curve ensures that the equipment is properly balanced and safe to operate. Installation is simple, with pre-drilled mounting holes and supplied hardware.
May 1995 FORM:
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
OM-1100A
For Cross Slides
SECTION 1 – INTRODUCTION
Table 1-1. Specifications
Total Slide
Movement
Overall
Dimensions
Weight
4 in. (102 mm)
1-5/8 x 6 x 16 in.*
(41 x 152 x 406 mm)
8 lbs. 12 oz. (4 kg)
*Includes 6 in. (152 mm) for crank handle
Chart 1-1. Cross Slide Loading
CAUTION: INCORRECT CROSS SLIDE
LOADING can cause personal injury and
equipment damage.
• Total load weight must fall within limits of
loading curve.
Distance
Load Weight
(Center Of Mass)
Carrier Face
Plate
Bottom
Pan
S-0094
SA-052 831-A
LOADING SAFETY CHECK:
1. Estimate combined weight of all accessories and
distance of center of mass from carrier face plate.
2. Check values against chart. Loading condition
must fall within safe operation zone curve.
3. Adjust weight/distance if necessary.
1-1. GENERAL INFORMATION AND SAFETY
A. General
Information presented in this manual and on various la-
bels, tags, and plates on the unit pertains to equipment
design, installation, operation, maintenance, and
troubleshooting which should be read, understood, and
followed for the safe and effective use of this equipment.
B. Safety
The installation, operation, maintenance, and trouble-
shooting of arc welding equipment requires practices
and procedures which ensure personal safety and the
safety of others. Therefore, this equipment is to be in-
stalled, operated, and maintained only by qualified
persons in accordance with this manual and all applica-
ble codes such as, but not limited to, those listed at the
end of Section 1 – Safety Rules For Operation Of Arc
OM-1100 Page 2
Welding Power Source in the welding power source
Owner’s Manual.
1-2. SAFETY ALERT SYMBOL AND SIGNAL
WORDS
The following safety alert symbol and signal words are
used throughout this manual to call attention to and
identify different levels of hazard and special instruc-
tions.
This safety alert symbol is used with the signal
words WARNING and CAUTION to call atten-
tion to the safety statements.
WARNING statements identify procedures or
practices which must be followed to avoid seri-
ous personal injury or loss of life.
CAUTION statements identify procedures or
practices which must be followed to avoid minor
personal injury or damage to this equipment.
IMPORTANT statements identify special instructions
necessary for the most efficient operation of this equip-
ment.
1-3. DESCRIPTION
The cross slide design provides horizontal or vertical
movement of welding equipment. Two cross slides may
be installed to provide X-Y (both horizontal and vertical)
movement of welding equipment.
Cross slide mounted equipment must be within the lim-
its of the loading curve shown in Chart 1-1.
SECTION 2 – INSTALLATION AND MAINTENANCE
WARNING: ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Shut down wire feeder system and
welding power source, and disconnect
input power employing lockout/tagging
procedures before inspecting, installing,
or servicing.
Lockout/tagging procedures consist of pad-
locking line disconnect switch in open posi-
tion, removing fuses from fuse box, or shut-
ting off and red-tagging circuit breaker or oth-
er disconnecting device.
2-1. INSTALLATION (Figure 3-1)
WARNING: Read and follow safety infor-
mation at beginning of entire Section 2
before proceeding.
CAUTION: WELD SPATTER, DIRT, AND
DUST can affect cross slide operation.
• Mount cross slide where it will be least
subjected to weld spatter, dirt, and dust.
IMPORTANT: The 4-1/4 in. (108 mm) square mounting
hole pattern in the cross slide bottom pan and carrier
plate permits mounting one cross slide on top of another
to provide X-Y movement
1. Turn crank handle to move carrier plate and ex-
pose two mounting holes in bottom pan. Install
supplied 3/8-16 x 1-1/4 cap screws and lock
washers.
2. Turn crank handle to move carrier plate in oppo-
site direction and expose two remaining
mounting holes in bottom pan. Install supplied
3/8-16 x 1-1/4 cap screws and lock washers.
3. Install welding equipment on carrier plate using
customer supplied 3/8-16 cap screws. Mounting
screws should not interfere with carrier travel.
2-2. SHAFT TENSION ADJUSTMENT (Figure 3-1)
WARNING: Read and follow safety infor-
mation at beginning of entire Section 2
before proceeding.
The cross slide has been factory set to require 12 in.-lb.
(82.7 kPa) torque to turn the crank handle and should
not require further adjustment. If the cross slide compo-
nents work loose and the handle turns too freely,
readjust as follows:
1. Remove all equipment mounted to the carrier
plate.
2. Loosen cone point set screw. Tighten screw drive
nut on the drive screw until sufficient drag is felt
while turning crank handle.
3. Tighten set screw on the screw drive nut.
4. Install equipment removed in Step 1.
2-3. CLEANING AND LUBRICATION (Figure 3-1)
WARNING: Read and follow safety infor-
mation at beginning of entire Section 2
before proceeding.
Every six months clean and apply a light lubricant, such
as SAE 20 oil, to the drive screw and the slide bars (see
Figure 3-1, items 4, 10 and 11).
OM-1100 Page 3
SECTION 3 – PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
12
14
15
13
ST-044 347-D
Figure 3-1. Complete Assembly
Description Quantity
Part
No.
Item
No.
1 044 205 CRANK, handle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 010 650 PIN, spring CS .125 x 1.000 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 128 501 SCREW, set stl sch 10-32 x .125 cone point 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 128 500 NUT, screw drive 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 078 671 PIN, spring CS .093 x .500 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 085 199 SCREW, drive 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 174 661 PLATE, end w/bearing 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 085 198 BEARING, thrust 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 000 365 RING, retainer E .500 shaft grv x .025thk 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 044 211 CARRIER, plate 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 044 214 NUT, cross slide 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 079 304 SCREW, cap stl sch slflkg .250-20 x .750 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 174 619 BAR, slide 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 044 208 BAR, slide 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 114 414 SCREW, mach stl phflh 10-24 x .875 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 174 659 PLATE, end 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 601 966 SCREW, cap stl hexhd .375-16 x 1.250 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 602 221 WASHER, lock stl intl tooth .375 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
602 213 WASHER, lock stl split .375 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
601 872 NUT, stl hex full .375-16 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 044 201 PAN, bottom 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 144 415 SCREW, mach stl phflh 10-24 x .625 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BE SURE TO PROVIDE MODEL WHEN ORDERING REPLACEMENT PARTS.
-
1
-
2
-
3
Miller JK000000 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
The Miller JK000000 Cross Slide is a versatile and durable piece of equipment designed to provide horizontal or vertical movement for welding equipment. With a total slide movement of 4 inches and a weight capacity of 8 lbs. 12 oz., this cross slide can accommodate a wide range of welding equipment and accessories. The included loading curve ensures that the equipment is properly balanced and safe to operate. Installation is simple, with pre-drilled mounting holes and supplied hardware.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KB065368 Owner's manual
-
-
Miller Travel Master SB-10D Owner's manual
-
-
-
-
-
-
-