Pioneer DVD / CD WRITER User manual

Brand: Pioneer

Model: DVD / CD WRITER

Category: Optical disc drives

Type: User manual

Pioneer DVD / CD WRITER lets you easily read and write a wide range of disc formats, including DVD-R/RW, DVD+R/RW, CD-R/RW, and more. With write speeds up to 24X for CD-R and 8X for DVD-R, you can quickly and easily create your own custom discs. The drive also features a 2MB buffer memory, which helps to ensure smooth and reliable performance. Whether you're backing up important files, creating music CDs, or watching DVDs, Pioneer DVD / CD WRITER is the perfect choice for all your disc-related needs.

Page is loading ...

English

Nederlands Español Italiano Deutsch Français

FEDERAL COMMUNICATIONS COMMISSION

DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause un-

desired operation.

Product Name: DVD-R/RW DVD+R/RW CD-R/RW WRITER

Model Number: DVR-A06

Responsible Party Name: PIONEER ELECTRONICS (USA) INC.

Custormer Support Division

Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810 U.S.A.

Phone: (310) 952-2820

Thank you for buying this Pioneer product.

Please review these operating instructions to install and run your drive properly. After you have

finished reading the instructions, put them away in a safe place for future reference.

K015 En

The Generation of Acoustical Noise Is Less Than 70dB.

(ISO7779/DIN45635)

For pluggable equipment the socket-outlet shall be installed near

the equipment and shall be easily accessible.

Location: on top of the cover.

IMPORTANT NOTICE

Record the model and serial numbers of this drive below. The

numbers are on the top panel.

Model No. DVR-A07

Serial No.

Keep these numbers for future reference.

H059 En

CLASS 1 LASER PRODUCT

LASER KLASSE 1

WARNING:

Handling the cord on this product or cords associated with accessories sold with this drive exposes

the user to lead, a chemical known to the State of California and other governmental entities to

cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

English

SAFETY INSTRUCTIONS

To ensure your personal safety and to maximize the full operating potential of your drive, read and follow these

safety notices:

ENVIRONMENT - DO NOT expose the unit to excessive dust, high temperature, or high humidity. Please

avoid subjecting the unit to vibrations or shocks.

POWER - Turn OFF your system before installating hardware devices.

READ & RETAIN INSTRUCTIONS - Read all safety and operating instructions before installing the drive.

FOLLOW INSTRUCTIONS - Follow all operating and use instructions.

HEED WARNINGS - All warnings must be adhered to.

CLEANING - DO NOT use liquid, aerosol cleaners, or alcohol on the dirve. Use only a damp cloth to clean

the exterior housing.

WATER AND MOISTURE - DO NOT use this product near water.

POWER SOURCES - Operate this product from the type of power source indicated on the label. If you are

not sure of the type of power available, consult an authorized Pioneer dealer.

OVERLOADING - DO NOT overload wall outlets and extension cords. Doing so can result in fire or electric

shock.

OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product. Touching dangerous voltage

points may cause a short resulting in fire or electric shock. Do not spill liquid of any kind on this product.

CONDENSATION - If the drive is moved from a cool environment to a warmer location, moisture can form

inside of the mechanism causing performance issues. If you are moving the unit to a location with a warmer

temperature, let the product stand for 1 to 2 hours at the new site before turning it ON.

SERVICING - Do not attempt to repair this product yourself. Opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

(Refer to the enclosed Service and Support Card.)

÷ Remove dust or lint from the disc with a soft cloth by

wiping from the inside to the outside edge rather than in

a circular motion.

÷ Do not use record-cleaning or anti-static agents as the

solutions may cause damage to a disc.

Always store your discs in proper DVD-R storage cases when

not in use. Check for dirt or dust on discs especially on the

recording side before use.

÷ Avoid touching or scratching the signal surface (shiny

side) of the disc.

÷ Hold the disc by the edges or by the center hole and one

edge.

÷ Do not affix paper or other types of labels to the disc.

÷ Discard warped or cracked discs as they may cause

damage to the drive.

÷ Avoid specialty shaped discs such as hearts or polygons.

• Write Speed

1X, 2X, 4X, and 8X Zone CLV at DVD-R

1X, 2X, and 4X CLV at DVD-RW

2.4X, 4X, 6X CLV, and 8X Zone CLV at DVD+R

2.4X and 4X CLV at DVD+RW

4X, 8X, 16X and 24X Zone CLV at CD-R

4X, 10X, 16X, and 24X Zone CLV at CD-RW

• Maximum Read Speed

12X CAV at DVD-ROM

40X CAV at CD-ROM

• Buffer Memory Size :

2 MBytes (Write/Read)

* ATAPI Interface:

ATA/ATAPI-5 and SFFC INF-8090i Ver5.11

• IDE Data Transfer Mode :

PIO Mode 4/Multi Word DMA Mode 2/Ultra DMA Mode 2

• Supports Video CD

• 5.25inch Half-Height built in type

• Stereo Audio Output

• LCD Tilt Servo Mechanism

• Horizontal/Vertical orientation available

• Low vibration Mechanism by DRA system

• Headophone Output and Volume Control Knob (optional)

Disc Format (Read/Write)

• KODAK Photo CD Singles and Multi-session

• Video CD and CD text data

• CD-ROM, CD-R and CD-RW (HS & US) discs

• DVD-ROM, DVD-R (Ver 2.0 General) and DVD-RW (Ver 1.0 & 1.1) discs

• DVD single layer/dual layer /120 mm disc/80 mm disc

• Reads DVD-RAM (Ver 2.0 & 2.1)

• +R (Ver 1.0 & 1.1)

• +RW (Version 1.2)

• CD-ROM Mode 1

• CD-ROM XA Mode2 (form 1, form2)

• CD-DA

• CD-Extra (CD PLUS)

• Supports Buffer Under Run protection (CD & DVD)

* Drive will obtain Microsoft® Windows® Logo Program (WHQL) certification

Note:

To write to disc, install an applicationam that supports your chosen format.

FEATURES

English

ABOUT REGION CODES

The region code can only be changed 5 times including the first setting. The fifth

change becomes PERMANENT, therefore, avoid changing the region codes unless

absolutely necessary.

÷ Region codes are part of the DVD Standard for devices. However, Region codes

on DVD discs are optional. A disc without a specific Region code can be played

on all standard players.

INTERFACE

FRONT VIEW

1 Forced Ejection Hole

If the tray fails to open when pressing the Eject button, turn off the system power and wait for

the disc to stop spinning. Once the power is OFF, it make take as long as 1 minute for the disc

to stop. Insert a stiff rod into the hole and push to eject the tray. During normal operation,

always use the Eject button to open the tray.

2 BUSY Indicator

Operation status is indicated as follows.

During reading: Lights

During writing: Lights

3 Ventilation Hole

Do not block the vents.

4 Eject Button

To unload/load the disc, press the Eject button.

5 Disc Tray

Open the tray by pressing the Eject button. Place a CD or DVD disc on to the tray with the

label facing up. Press the Eject button again or push the front panel of tray to close the tray

and load the disc.

Do not attempt to use force to pull out the disc tray.

When playing 8 cm (3.15") Discs

When the drive is installed vertically an 8cm (3.15") disc cannot be played. Attaching an adapter

has no affect on on verically mounted drives.

Note: The Volumn Control Knob and the Head Phone Jack are optional.

INTERFACE

REAR VIEW

Pin Name Function

1 L Left channel audio output

2 G Ground

3 G Ground

4 R Right channel audio output

Pin Name Function

1 MA on The drive is the master device

2 SL on The drive is the slave device

3 CS on Set the drive to Cable Select

4 Reserved

5 Reserved

6 Audio Output

This connector is for output of analog audio and is compatible with Molex 70553. Choose a

suitable connection cable.

Pin Name Function

1 +12 Power supply input for DC +12 V

2 G Ground

3 G Ground

4 +5 Power supply input for DC +5 V

7 Device Configuration Jumper

The Switch changes to ON when a jumper is added (Pin 1 is on lower-right).

Verify that the power is OFF before changing the jumper setting.

The factory default forPin # 1 is ON.

8 Host IDE Interface

Use a 40-pin flat cable to connect the drive to the computer's Enhanced-IDE port. The maximum

length for this cable is 18 inches.

9 DC Input

English

1 Turn OFF the computer and remove the power cord from the wall outlet. Remove the

cover or front panel from the PC.

2 Remove the blank panel covering an empty 5.25” slot.

3 Install the slide rails on the drive.

(slide rails may be purchased separately from the computer manufacturer)

4 Insert the drive into the slot.

5 Refer to the computer’s instruction manual if additional mounting methods are required.

÷ Mounting screws must be no longer than 3/16” or 5 mm. Using longer screws may

damage the drive.

÷ When mounting screws are loose, the vibrations from the spinning disc may cause a

ripping noise. To prevent this noise, tighten the screws.

INSTALLATION

÷ Turn OFF the power to the computer.

÷ Connect the power cable from the computer to the drive with the connector in the

correct orientation.

÷ Connect the IDE interface cable to the drive with the IDE connector’s pin 1 aligned

with the drive’s pin 1.

÷ If a sound card is being used, connect the computer’s audio output to the sound card

using an audio cable.

This drive is powered by the computer rather than having a separate power cord.

Do not use a power supply other than the computer’s internal unit.

CONNECTIONS

English

[Setting]

This drive may be installed horizontally or vertically.

[Disc Size]

⇑ 12 cm (4.72”) / 8 cm (3.15”)*

* 8 cm (3.15") discs cannot be used on vertically installed drives.

[Data Transfer Rate]

Data Read (Sustained)

DVD Max. 16.2 MBytes/sec. (5X-12X CAV over 16-block transfer)

CD Max. 6.0 MBytes/sec. (17.2-40X CAV over 16-block transfer)

Data Write (Sustained)

DVD Ave. 10.8 MBytes/sec. (8X DVD-R, +R)

CD Ave. 3.6 MBytes/sec. (24X CD-R)

Host Interface specification

PIO Mode 4, Multiword DMA Mode2 16.6 MBytes/sec.

Ultra DMA Mode2 *33.3 MBytes/sec.

• The data transfer rate may not be output due to disc conditions (scratches, etc.).

NOTE:

Ifattempting to read dirty, damaged or unbalanced media, the drive automatically slows the

disc rotation thus lowering the transfer rate.

[Access Time/ Seek Time]

Access time (Random average)

DVD-ROM 140 ms DVD-RAM 150 ms CD-ROM 130 ms

Seek time (Random average)

DVD-ROM 130 ms DVD-RAM 140 ms CD-ROM 120 ms

[Audio Characteristic]

Line Out 0.75 ± 0.1 Vrms (at 10 kΩ load)

[Others]

Power Supply DC +12 V, 0.6 A

DC +5 V, 0.8 A

Dimensions 148 (W) x 42.3 (H) x 198 (D) mm

(including front panel)

5-27/32 (W) x 1-11/16 (H) x 7-25/32 (D) in.

Weight 1.1 kg (2.43 lb)

Operation temperature +5°C to +45°C (41°F to 113°F)

Operation humidity 5% to 85% (no condensation)

Storage temperature – 40°C to +60°C (– 40°F to 140°F)

Storage humidity 5% to 90% (no condensation)

[Accessories]

Mounting screws (4)

Operating instructions (1)

CD of bundled software programs (1)

NOTE: Specifications and design subject to modifications without notice, due to improvements.

Published by Pioneer Corporation.

SPECIFICATIONS

Page is loading ...

Pioneer DVD / CD WRITER User manual

Brand: Pioneer

Model: DVD / CD WRITER

Category: Optical disc drives

Type: User manual

Download PDF

report

in other languages

français: Pioneer DVD / CD WRITER Manuel utilisateur
español: Pioneer DVD / CD WRITER Manual de usuario

Pioneer DVD / CD WRITER User manual

Pioneer DVD / CD WRITER User manual

in other languages

Related papers

Other documents