Closet Maid 71031 User manual

Brand
Closet Maid
Model
71031
Type
User manual

Closet Maid 71031 is a versatile shelving system that allows you to add shelving wherever you need it. It includes all the necessary hardware for quick and easy installation, and the shelves can be cut to any desired length. The shelves are made of sturdy steel and can hold up to 50 pounds of weight, making them ideal for storing a variety of items.

Closet Maid 71031 is a versatile shelving system that allows you to add shelving wherever you need it. It includes all the necessary hardware for quick and easy installation, and the shelves can be cut to any desired length. The shelves are made of sturdy steel and can hold up to 50 pounds of weight, making them ideal for storing a variety of items.

3’
Shelf
Add a shelf wherever you need it.
Includes all hardware
71031
71031
36” W x 12”D
91,5AN x 30,5P cm
71031
www.closetmaid.com
REPLACEMENT
POLICY
If a ClosetMaid
®
product does not
give the user complete satisfaction when
installed in accordance with manufactur-
er's instructions, it will be exchanged
free of charge. Only the unsatisfactory
part in a multi-piece product will
be exchanged.
Manufacturer reserves the right to
change specifications without notice.
Made in U.S.A.
1-800-874-0008 (U.S.A., Canada)
3’
Shelf
Add a shelf wherever you need it.
Includes all hardware
36” W x 12”D
91,5AN x 30,5P cm
Note: If necessary, cut shelf between wires with a hacksaw or boltcutter in one inch increments to desired length.
CAUTION: Sharp ends on shelf when cut. Immediately place endcaps onto cut shelf ends.
a. Place shelf endcaps onto exposed shelf wires.
Nota: Si es necesario, corte la repisa a la longitud deseada con una sierra cortametales o un cortador de pernos en
incrementos de una pulgada (2,54 cm).
PRECAUCIÓN: Los extremos de las repisas quedan afilados al cortarlas. Coloque los tapones en los extremos de las
repisas cortadas inmediatamente.
a. Coloque los tapones en los alambres expuestos de la repisa.
1
2
a. Lightly draw a level line at desired shelf location the exact length of shelf. Measure and mark a wall clip location
2" from each end of shelf. Measure and mark remaining wall clips as shown below. For cut shelves in other sizes,
install a wall clip 2" from each end of shelf and space remaining wall clips at even intervals between end wall clips.
Never install wall clips more than 11" apart.
b.Drill 1/4" holes at marked locations. DO NOT PUNCH HOLES.
c.  Push wall clip into drilled holes. Push pin into wall clip. Use bottom of hammer handle to push in pin. For removal,
pry pin out with screwdriver.
a. Trace una línea nivelada en la ubicación deseada con la longitud exacta de la repisa. Mida y marque la ubicación
del fijador en la pared a 2" (5 cm) hacia adentro de cada extremo de la repisa. Mida y marque el resto de las
ubicaciones de los fijadores como se muestra a continuación. Para repisas cortadas a otros tamaños, instale un
fijador a 2" (5 cm) de cada extremo de la repisa y coloque los demás fijadores a intervalos iguales entre los de los
extremos. Nunca instala los fijadores con una separación mayor a 11" (27,9 cm).
b. Perfore agujeros de 1/4" (6 mm) en las ubicaciones marcadas. USE TALADRO SOLAMENTE.
c. Empuje los fijadores en los agujeros perforados. Empuje la clavija en el fijador. Use la parte inferior del mango de
un martillo para empujar la clavija. Para quitarlas, saque la clavija con un destornillador.
Note Nota
# 1021 # 1031
2' (61cm)
2" (5,1cm)
8" (20,3cm)
6" (15,2cm) 6" (15,2cm)
2" (5,1cm)
a.
b. c.
3
a.
a.
c. d.b.
a. Firmly push shelf into wall clips. Allow shelf to hang down from clips.
b. Position support bracket on shelf (as shown) no more than 3" from end of shelf. Space support brackets
no more than 36" apart.
c. Level shelf. Drill 1/4" hole through wall using bracket as guide. DO NOT PUNCH HOLES.
d. Push anchor into drilled hole. Push pin into anchor. Use bottom of hammer handle to push in pin.
a. Empuje la repisa firmemente en los fijadores. Deje que la repisa cuelgue de los fijadores.
b. Coloque el soporte en la repisa (como se muestra) a no más de 3" (7,6 cm) del extremo de la repisa. Coloque los
soportes con un separación máxima de 36" (91,4 cm).
c. Nivele la repisa. Perfore agujeros de 1/4" (6 mm) en la pared usando el soporte como guía. USE TALADRO SOLAMENTE.
d. Empuje el tarugo en el agujero perforado. Empuje la clavija en el tarugo. Use la parte inferior del mango de un
martillo para empujar la clavija.
x x x
x
3' (91cm)
2" (5,1cm)
8" (20,3cm) 8" (20,3cm)
8" (20,3cm) 8" (20,3cm)
2" (5,1cm)
x x x x
x
# 1041
4' (1,22cm)
2" (5,1cm)
9" (23cm) 9" (23cm)
9" (23cm) 9" (23cm)8" (20,3cm)
2" (5,1cm)
x x x x x
x
# 1061
6' (1,83cm)
2" (5,1cm)
10" (25,4cm) 10" (25,4cm)8" (20,3cm)
10" (25,4cm) 10" (25,4cm) 10" (25,4cm) 10" (25,4cm)
2" (5,1cm)
x x xx x xx
x
  • Page 1 1

Closet Maid 71031 User manual

Brand
Closet Maid
Model
71031
Type
User manual

Closet Maid 71031 is a versatile shelving system that allows you to add shelving wherever you need it. It includes all the necessary hardware for quick and easy installation, and the shelves can be cut to any desired length. The shelves are made of sturdy steel and can hold up to 50 pounds of weight, making them ideal for storing a variety of items.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents